diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/mfd/Kconfig | 10 | ||||
-rw-r--r-- | drivers/mfd/Makefile | 1 | ||||
-rw-r--r-- | drivers/mfd/janz-cmodio.c | 304 |
3 files changed, 315 insertions, 0 deletions
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 93d0e31c0438..05c137d16b04 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -418,6 +418,16 @@ config MFD_RDC321X southbridge which provides access to GPIOs and Watchdog using the southbridge PCI device configuration space. +config MFD_JANZ_CMODIO + tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board" + select MFD_CORE + depends on PCI + help + This is the core driver for the Janz CMOD-IO PCI MODULbus + carrier board. This device is a PCI to MODULbus bridge which may + host many different types of MODULbus daughterboards, including + CAN and GPIO controllers. + endmenu menu "Multimedia Capabilities Port drivers" diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index f177e064b31b..21eff85b288a 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -65,3 +65,4 @@ obj-$(CONFIG_MFD_TIMBERDALE) += timberdale.o obj-$(CONFIG_PMIC_ADP5520) += adp5520.o obj-$(CONFIG_LPC_SCH) += lpc_sch.o obj-$(CONFIG_MFD_RDC321X) += rdc321x-southbridge.o +obj-$(CONFIG_MFD_JANZ_CMODIO) += janz-cmodio.o diff --git a/drivers/mfd/janz-cmodio.c b/drivers/mfd/janz-cmodio.c new file mode 100644 index 000000000000..9ed630799acc --- /dev/null +++ b/drivers/mfd/janz-cmodio.c @@ -0,0 +1,304 @@ +/* + * Janz CMOD-IO MODULbus Carrier Board PCI Driver + * + * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu> + * + * Lots of inspiration and code was copied from drivers/mfd/sm501.c + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/pci.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/mfd/core.h> + +#include <linux/mfd/janz.h> + +#define DRV_NAME "janz-cmodio" + +/* Size of each MODULbus module in PCI BAR4 */ +#define CMODIO_MODULBUS_SIZE 0x200 + +/* Maximum number of MODULbus modules on a CMOD-IO carrier board */ +#define CMODIO_MAX_MODULES 4 + +/* Module Parameters */ +static unsigned int num_modules = CMODIO_MAX_MODULES; +static unsigned char *modules[CMODIO_MAX_MODULES] = { + "empty", "empty", "empty", "empty", +}; + +module_param_array(modules, charp, &num_modules, S_IRUGO); +MODULE_PARM_DESC(modules, "MODULbus modules attached to the carrier board"); + +/* Unique Device Id */ +static unsigned int cmodio_id; + +struct cmodio_device { + /* Parent PCI device */ + struct pci_dev *pdev; + + /* PLX control registers */ + struct janz_cmodio_onboard_regs __iomem *ctrl; + + /* hex switch position */ + u8 hex; + + /* mfd-core API */ + struct mfd_cell cells[CMODIO_MAX_MODULES]; + struct resource resources[3 * CMODIO_MAX_MODULES]; + struct janz_platform_data pdata[CMODIO_MAX_MODULES]; +}; + +/* + * Subdevices using the mfd-core API + */ + +static int __devinit cmodio_setup_subdevice(struct cmodio_device *priv, + char *name, unsigned int devno, + unsigned int modno) +{ + struct janz_platform_data *pdata; + struct mfd_cell *cell; + struct resource *res; + struct pci_dev *pci; + + pci = priv->pdev; + cell = &priv->cells[devno]; + res = &priv->resources[devno * 3]; + pdata = &priv->pdata[devno]; + + cell->name = name; + cell->resources = res; + cell->num_resources = 3; + + /* Setup the subdevice ID -- must be unique */ + cell->id = cmodio_id++; + + /* Add platform data */ + pdata->modno = modno; + cell->platform_data = pdata; + cell->data_size = sizeof(*pdata); + + /* MODULbus registers -- PCI BAR3 is big-endian MODULbus access */ + res->flags = IORESOURCE_MEM; + res->parent = &pci->resource[3]; + res->start = pci->resource[3].start + (CMODIO_MODULBUS_SIZE * modno); + res->end = res->start + CMODIO_MODULBUS_SIZE - 1; + res++; + + /* PLX Control Registers -- PCI BAR4 is interrupt and other registers */ + res->flags = IORESOURCE_MEM; + res->parent = &pci->resource[4]; + res->start = pci->resource[4].start; + res->end = pci->resource[4].end; + res++; + + /* + * IRQ + * + * The start and end fields are used as an offset to the irq_base + * parameter passed into the mfd_add_devices() function call. All + * devices share the same IRQ. + */ + res->flags = IORESOURCE_IRQ; + res->parent = NULL; + res->start = 0; + res->end = 0; + res++; + + return 0; +} + +/* Probe each submodule using kernel parameters */ +static int __devinit cmodio_probe_submodules(struct cmodio_device *priv) +{ + struct pci_dev *pdev = priv->pdev; + unsigned int num_probed = 0; + char *name; + int i; + + for (i = 0; i < num_modules; i++) { + name = modules[i]; + if (!strcmp(name, "") || !strcmp(name, "empty")) + continue; + + dev_dbg(&priv->pdev->dev, "MODULbus %d: name %s\n", i, name); + cmodio_setup_subdevice(priv, name, num_probed, i); + num_probed++; + } + + /* print an error message if no modules were probed */ + if (num_probed == 0) { + dev_err(&priv->pdev->dev, "no MODULbus modules specified, " + "please set the ``modules'' kernel " + "parameter according to your " + "hardware configuration\n"); + return -ENODEV; + } + + return mfd_add_devices(&pdev->dev, 0, priv->cells, + num_probed, NULL, pdev->irq); +} + +/* + * SYSFS Attributes + */ + +static ssize_t mbus_show(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct cmodio_device *priv = dev_get_drvdata(dev); + + return snprintf(buf, PAGE_SIZE, "%x\n", priv->hex); +} + +static DEVICE_ATTR(modulbus_number, S_IRUGO, mbus_show, NULL); + +static struct attribute *cmodio_sysfs_attrs[] = { + &dev_attr_modulbus_number.attr, + NULL, +}; + +static const struct attribute_group cmodio_sysfs_attr_group = { + .attrs = cmodio_sysfs_attrs, +}; + +/* + * PCI Driver + */ + +static int __devinit cmodio_pci_probe(struct pci_dev *dev, + const struct pci_device_id *id) +{ + struct cmodio_device *priv; + int ret; + + priv = kzalloc(sizeof(*priv), GFP_KERNEL); + if (!priv) { + dev_err(&dev->dev, "unable to allocate private data\n"); + ret = -ENOMEM; + goto out_return; + } + + pci_set_drvdata(dev, priv); + priv->pdev = dev; + + /* Hardware Initialization */ + ret = pci_enable_device(dev); + if (ret) { + dev_err(&dev->dev, "unable to enable device\n"); + goto out_free_priv; + } + + pci_set_master(dev); + ret = pci_request_regions(dev, DRV_NAME); + if (ret) { + dev_err(&dev->dev, "unable to request regions\n"); + goto out_pci_disable_device; + } + + /* Onboard configuration registers */ + priv->ctrl = pci_ioremap_bar(dev, 4); + if (!priv->ctrl) { + dev_err(&dev->dev, "unable to remap onboard regs\n"); + ret = -ENOMEM; + goto out_pci_release_regions; + } + + /* Read the hex switch on the carrier board */ + priv->hex = ioread8(&priv->ctrl->int_enable); + + /* Add the MODULbus number (hex switch value) to the device's sysfs */ + ret = sysfs_create_group(&dev->dev.kobj, &cmodio_sysfs_attr_group); + if (ret) { + dev_err(&dev->dev, "unable to create sysfs attributes\n"); + goto out_unmap_ctrl; + } + + /* + * Disable all interrupt lines, each submodule will enable its + * own interrupt line if needed + */ + iowrite8(0xf, &priv->ctrl->int_disable); + + /* Register drivers for all submodules */ + ret = cmodio_probe_submodules(priv); + if (ret) { + dev_err(&dev->dev, "unable to probe submodules\n"); + goto out_sysfs_remove_group; + } + + return 0; + +out_sysfs_remove_group: + sysfs_remove_group(&dev->dev.kobj, &cmodio_sysfs_attr_group); +out_unmap_ctrl: + iounmap(priv->ctrl); +out_pci_release_regions: + pci_release_regions(dev); +out_pci_disable_device: + pci_disable_device(dev); +out_free_priv: + kfree(priv); +out_return: + return ret; +} + +static void __devexit cmodio_pci_remove(struct pci_dev *dev) +{ + struct cmodio_device *priv = pci_get_drvdata(dev); + + mfd_remove_devices(&dev->dev); + sysfs_remove_group(&dev->dev.kobj, &cmodio_sysfs_attr_group); + iounmap(priv->ctrl); + pci_release_regions(dev); + pci_disable_device(dev); + kfree(priv); +} + +#define PCI_VENDOR_ID_JANZ 0x13c3 + +/* The list of devices that this module will support */ +static DEFINE_PCI_DEVICE_TABLE(cmodio_pci_ids) = { + { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_JANZ, 0x0101 }, + { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, PCI_VENDOR_ID_JANZ, 0x0100 }, + { 0, } +}; +MODULE_DEVICE_TABLE(pci, cmodio_pci_ids); + +static struct pci_driver cmodio_pci_driver = { + .name = DRV_NAME, + .id_table = cmodio_pci_ids, + .probe = cmodio_pci_probe, + .remove = __devexit_p(cmodio_pci_remove), +}; + +/* + * Module Init / Exit + */ + +static int __init cmodio_init(void) +{ + return pci_register_driver(&cmodio_pci_driver); +} + +static void __exit cmodio_exit(void) +{ + pci_unregister_driver(&cmodio_pci_driver); +} + +MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>"); +MODULE_DESCRIPTION("Janz CMOD-IO PCI MODULbus Carrier Board Driver"); +MODULE_LICENSE("GPL"); + +module_init(cmodio_init); +module_exit(cmodio_exit); |