diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/ata/sata_mv.c | 35 |
1 files changed, 18 insertions, 17 deletions
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index d689fb9ceb96..55d3ce087304 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -272,17 +272,17 @@ enum { SATA_FIS_IRQ_CAUSE_OFS = 0x364, SATA_FIS_IRQ_AN = (1 << 9), /* async notification */ - LTMODE_OFS = 0x30c, + LTMODE_OFS = 0x30c, /* requires read-after-write */ LTMODE_BIT8 = (1 << 8), /* unknown, but necessary */ - PHY_MODE3 = 0x310, - PHY_MODE4 = 0x314, + PHY_MODE2_OFS = 0x330, + PHY_MODE3_OFS = 0x310, + PHY_MODE4_OFS = 0x314, /* requires read-after-write */ PHY_MODE4_CFG_MASK = 0x00000003, /* phy internal config field */ PHY_MODE4_CFG_VALUE = 0x00000001, /* phy internal config field */ PHY_MODE4_RSVD_ZEROS = 0x5de3fffa, /* Gen2e always write zeros */ PHY_MODE4_RSVD_ONES = 0x00000005, /* Gen2e always write ones */ - PHY_MODE2 = 0x330, SATA_IFCTL_OFS = 0x344, SATA_TESTCTL_OFS = 0x348, SATA_IFSTAT_OFS = 0x34c, @@ -3168,7 +3168,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, } port_mmio = mv_port_base(mmio, idx); - tmp = readl(port_mmio + PHY_MODE2); + tmp = readl(port_mmio + PHY_MODE2_OFS); hpriv->signal[idx].amps = tmp & 0x700; /* bits 10:8 */ hpriv->signal[idx].pre = tmp & 0xe0; /* bits 7:5 */ @@ -3192,25 +3192,25 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, u32 m2, m3; if (fix_phy_mode2) { - m2 = readl(port_mmio + PHY_MODE2); + m2 = readl(port_mmio + PHY_MODE2_OFS); m2 &= ~(1 << 16); m2 |= (1 << 31); - writel(m2, port_mmio + PHY_MODE2); + writel(m2, port_mmio + PHY_MODE2_OFS); udelay(200); - m2 = readl(port_mmio + PHY_MODE2); + m2 = readl(port_mmio + PHY_MODE2_OFS); m2 &= ~((1 << 16) | (1 << 31)); - writel(m2, port_mmio + PHY_MODE2); + writel(m2, port_mmio + PHY_MODE2_OFS); udelay(200); } /* - * Gen-II/IIe PHY_MODE3 errata RM#2: + * Gen-II/IIe PHY_MODE3_OFS errata RM#2: * Achieves better receiver noise performance than the h/w default: */ - m3 = readl(port_mmio + PHY_MODE3); + m3 = readl(port_mmio + PHY_MODE3_OFS); m3 = (m3 & 0x1f) | (0x5555601 << 5); /* Guideline 88F5182 (GL# SATA-S11) */ @@ -3218,7 +3218,7 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, m3 &= ~0x1c; if (fix_phy_mode4) { - u32 m4 = readl(port_mmio + PHY_MODE4); + u32 m4 = readl(port_mmio + PHY_MODE4_OFS); /* * Enforce reserved-bit restrictions on GenIIe devices only. * For earlier chipsets, force only the internal config field @@ -3228,17 +3228,18 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, m4 = (m4 & ~PHY_MODE4_RSVD_ZEROS) | PHY_MODE4_RSVD_ONES; else m4 = (m4 & ~PHY_MODE4_CFG_MASK) | PHY_MODE4_CFG_VALUE; - writel(m4, port_mmio + PHY_MODE4); + writel(m4, port_mmio + PHY_MODE4_OFS); } /* * Workaround for 60x1-B2 errata SATA#13: * Any write to PHY_MODE4 (above) may corrupt PHY_MODE3, * so we must always rewrite PHY_MODE3 after PHY_MODE4. + * Or ensure we use writelfl() when writing PHY_MODE4. */ - writel(m3, port_mmio + PHY_MODE3); + writel(m3, port_mmio + PHY_MODE3_OFS); /* Revert values of pre-emphasis and signal amps to the saved ones */ - m2 = readl(port_mmio + PHY_MODE2); + m2 = readl(port_mmio + PHY_MODE2_OFS); m2 &= ~MV_M2_PREAMP_MASK; m2 |= hpriv->signal[port].amps; @@ -3251,7 +3252,7 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, m2 |= 0x0000900F; } - writel(m2, port_mmio + PHY_MODE2); + writel(m2, port_mmio + PHY_MODE2_OFS); } /* TODO: use the generic LED interface to configure the SATA Presence */ @@ -3269,7 +3270,7 @@ static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx, u32 tmp; port_mmio = mv_port_base(mmio, idx); - tmp = readl(port_mmio + PHY_MODE2); + tmp = readl(port_mmio + PHY_MODE2_OFS); hpriv->signal[idx].amps = tmp & 0x700; /* bits 10:8 */ hpriv->signal[idx].pre = tmp & 0xe0; /* bits 7:5 */ |