diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/clocksource/Kconfig | 7 | ||||
| -rw-r--r-- | drivers/clocksource/Makefile | 1 | ||||
| -rw-r--r-- | drivers/clocksource/timer-u300.c | 457 |
3 files changed, 0 insertions, 465 deletions
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig index 6bf89e242c36..b26bb9ea3e60 100644 --- a/drivers/clocksource/Kconfig +++ b/drivers/clocksource/Kconfig @@ -216,13 +216,6 @@ config PRIMA2_TIMER help Enables support for the Prima2 timer. -config U300_TIMER - bool "U300 timer driver" if COMPILE_TEST - depends on ARM - select CLKSRC_MMIO - help - Enables support for the U300 timer. - config NSPIRE_TIMER bool "NSpire timer driver" if COMPILE_TEST select CLKSRC_MMIO diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile index 08173383f2d9..ce8a3c01a72d 100644 --- a/drivers/clocksource/Makefile +++ b/drivers/clocksource/Makefile @@ -34,7 +34,6 @@ obj-$(CONFIG_ATLAS7_TIMER) += timer-atlas7.o obj-$(CONFIG_MXS_TIMER) += mxs_timer.o obj-$(CONFIG_CLKSRC_PXA) += timer-pxa.o obj-$(CONFIG_PRIMA2_TIMER) += timer-prima2.o -obj-$(CONFIG_U300_TIMER) += timer-u300.o obj-$(CONFIG_SUN4I_TIMER) += timer-sun4i.o obj-$(CONFIG_SUN5I_HSTIMER) += timer-sun5i.o obj-$(CONFIG_MESON6_TIMER) += timer-meson6.o diff --git a/drivers/clocksource/timer-u300.c b/drivers/clocksource/timer-u300.c deleted file mode 100644 index 37cba8dfd45f..000000000000 --- a/drivers/clocksource/timer-u300.c +++ /dev/null @@ -1,457 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * Copyright (C) 2007-2009 ST-Ericsson AB - * Timer COH 901 328, runs the OS timer interrupt. - * Author: Linus Walleij <linus.walleij@stericsson.com> - */ -#include <linux/interrupt.h> -#include <linux/time.h> -#include <linux/timex.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/types.h> -#include <linux/io.h> -#include <linux/clk.h> -#include <linux/err.h> -#include <linux/irq.h> -#include <linux/delay.h> -#include <linux/of_address.h> -#include <linux/of_irq.h> -#include <linux/sched_clock.h> - -/* Generic stuff */ -#include <asm/mach/map.h> -#include <asm/mach/time.h> - -/* - * APP side special timer registers - * This timer contains four timers which can fire an interrupt each. - * OS (operating system) timer @ 32768 Hz - * DD (device driver) timer @ 1 kHz - * GP1 (general purpose 1) timer @ 1MHz - * GP2 (general purpose 2) timer @ 1MHz - */ - -/* Reset OS Timer 32bit (-/W) */ -#define U300_TIMER_APP_ROST (0x0000) -#define U300_TIMER_APP_ROST_TIMER_RESET (0x00000000) -/* Enable OS Timer 32bit (-/W) */ -#define U300_TIMER_APP_EOST (0x0004) -#define U300_TIMER_APP_EOST_TIMER_ENABLE (0x00000000) -/* Disable OS Timer 32bit (-/W) */ -#define U300_TIMER_APP_DOST (0x0008) -#define U300_TIMER_APP_DOST_TIMER_DISABLE (0x00000000) -/* OS Timer Mode Register 32bit (-/W) */ -#define U300_TIMER_APP_SOSTM (0x000c) -#define U300_TIMER_APP_SOSTM_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_SOSTM_MODE_ONE_SHOT (0x00000001) -/* OS Timer Status Register 32bit (R/-) */ -#define U300_TIMER_APP_OSTS (0x0010) -#define U300_TIMER_APP_OSTS_TIMER_STATE_MASK (0x0000000F) -#define U300_TIMER_APP_OSTS_TIMER_STATE_IDLE (0x00000001) -#define U300_TIMER_APP_OSTS_TIMER_STATE_ACTIVE (0x00000002) -#define U300_TIMER_APP_OSTS_ENABLE_IND (0x00000010) -#define U300_TIMER_APP_OSTS_MODE_MASK (0x00000020) -#define U300_TIMER_APP_OSTS_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_OSTS_MODE_ONE_SHOT (0x00000020) -#define U300_TIMER_APP_OSTS_IRQ_ENABLED_IND (0x00000040) -#define U300_TIMER_APP_OSTS_IRQ_PENDING_IND (0x00000080) -/* OS Timer Current Count Register 32bit (R/-) */ -#define U300_TIMER_APP_OSTCC (0x0014) -/* OS Timer Terminal Count Register 32bit (R/W) */ -#define U300_TIMER_APP_OSTTC (0x0018) -/* OS Timer Interrupt Enable Register 32bit (-/W) */ -#define U300_TIMER_APP_OSTIE (0x001c) -#define U300_TIMER_APP_OSTIE_IRQ_DISABLE (0x00000000) -#define U300_TIMER_APP_OSTIE_IRQ_ENABLE (0x00000001) -/* OS Timer Interrupt Acknowledge Register 32bit (-/W) */ -#define U300_TIMER_APP_OSTIA (0x0020) -#define U300_TIMER_APP_OSTIA_IRQ_ACK (0x00000080) - -/* Reset DD Timer 32bit (-/W) */ -#define U300_TIMER_APP_RDDT (0x0040) -#define U300_TIMER_APP_RDDT_TIMER_RESET (0x00000000) -/* Enable DD Timer 32bit (-/W) */ -#define U300_TIMER_APP_EDDT (0x0044) -#define U300_TIMER_APP_EDDT_TIMER_ENABLE (0x00000000) -/* Disable DD Timer 32bit (-/W) */ -#define U300_TIMER_APP_DDDT (0x0048) -#define U300_TIMER_APP_DDDT_TIMER_DISABLE (0x00000000) -/* DD Timer Mode Register 32bit (-/W) */ -#define U300_TIMER_APP_SDDTM (0x004c) -#define U300_TIMER_APP_SDDTM_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_SDDTM_MODE_ONE_SHOT (0x00000001) -/* DD Timer Status Register 32bit (R/-) */ -#define U300_TIMER_APP_DDTS (0x0050) -#define U300_TIMER_APP_DDTS_TIMER_STATE_MASK (0x0000000F) -#define U300_TIMER_APP_DDTS_TIMER_STATE_IDLE (0x00000001) -#define U300_TIMER_APP_DDTS_TIMER_STATE_ACTIVE (0x00000002) -#define U300_TIMER_APP_DDTS_ENABLE_IND (0x00000010) -#define U300_TIMER_APP_DDTS_MODE_MASK (0x00000020) -#define U300_TIMER_APP_DDTS_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_DDTS_MODE_ONE_SHOT (0x00000020) -#define U300_TIMER_APP_DDTS_IRQ_ENABLED_IND (0x00000040) -#define U300_TIMER_APP_DDTS_IRQ_PENDING_IND (0x00000080) -/* DD Timer Current Count Register 32bit (R/-) */ -#define U300_TIMER_APP_DDTCC (0x0054) -/* DD Timer Terminal Count Register 32bit (R/W) */ -#define U300_TIMER_APP_DDTTC (0x0058) -/* DD Timer Interrupt Enable Register 32bit (-/W) */ -#define U300_TIMER_APP_DDTIE (0x005c) -#define U300_TIMER_APP_DDTIE_IRQ_DISABLE (0x00000000) -#define U300_TIMER_APP_DDTIE_IRQ_ENABLE (0x00000001) -/* DD Timer Interrupt Acknowledge Register 32bit (-/W) */ -#define U300_TIMER_APP_DDTIA (0x0060) -#define U300_TIMER_APP_DDTIA_IRQ_ACK (0x00000080) - -/* Reset GP1 Timer 32bit (-/W) */ -#define U300_TIMER_APP_RGPT1 (0x0080) -#define U300_TIMER_APP_RGPT1_TIMER_RESET (0x00000000) -/* Enable GP1 Timer 32bit (-/W) */ -#define U300_TIMER_APP_EGPT1 (0x0084) -#define U300_TIMER_APP_EGPT1_TIMER_ENABLE (0x00000000) -/* Disable GP1 Timer 32bit (-/W) */ -#define U300_TIMER_APP_DGPT1 (0x0088) -#define U300_TIMER_APP_DGPT1_TIMER_DISABLE (0x00000000) -/* GP1 Timer Mode Register 32bit (-/W) */ -#define U300_TIMER_APP_SGPT1M (0x008c) -#define U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT (0x00000001) -/* GP1 Timer Status Register 32bit (R/-) */ -#define U300_TIMER_APP_GPT1S (0x0090) -#define U300_TIMER_APP_GPT1S_TIMER_STATE_MASK (0x0000000F) -#define U300_TIMER_APP_GPT1S_TIMER_STATE_IDLE (0x00000001) -#define U300_TIMER_APP_GPT1S_TIMER_STATE_ACTIVE (0x00000002) -#define U300_TIMER_APP_GPT1S_ENABLE_IND (0x00000010) -#define U300_TIMER_APP_GPT1S_MODE_MASK (0x00000020) -#define U300_TIMER_APP_GPT1S_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_GPT1S_MODE_ONE_SHOT (0x00000020) -#define U300_TIMER_APP_GPT1S_IRQ_ENABLED_IND (0x00000040) -#define U300_TIMER_APP_GPT1S_IRQ_PENDING_IND (0x00000080) -/* GP1 Timer Current Count Register 32bit (R/-) */ -#define U300_TIMER_APP_GPT1CC (0x0094) -/* GP1 Timer Terminal Count Register 32bit (R/W) */ -#define U300_TIMER_APP_GPT1TC (0x0098) -/* GP1 Timer Interrupt Enable Register 32bit (-/W) */ -#define U300_TIMER_APP_GPT1IE (0x009c) -#define U300_TIMER_APP_GPT1IE_IRQ_DISABLE (0x00000000) -#define U300_TIMER_APP_GPT1IE_IRQ_ENABLE (0x00000001) -/* GP1 Timer Interrupt Acknowledge Register 32bit (-/W) */ -#define U300_TIMER_APP_GPT1IA (0x00a0) -#define U300_TIMER_APP_GPT1IA_IRQ_ACK (0x00000080) - -/* Reset GP2 Timer 32bit (-/W) */ -#define U300_TIMER_APP_RGPT2 (0x00c0) -#define U300_TIMER_APP_RGPT2_TIMER_RESET (0x00000000) -/* Enable GP2 Timer 32bit (-/W) */ -#define U300_TIMER_APP_EGPT2 (0x00c4) -#define U300_TIMER_APP_EGPT2_TIMER_ENABLE (0x00000000) -/* Disable GP2 Timer 32bit (-/W) */ -#define U300_TIMER_APP_DGPT2 (0x00c8) -#define U300_TIMER_APP_DGPT2_TIMER_DISABLE (0x00000000) -/* GP2 Timer Mode Register 32bit (-/W) */ -#define U300_TIMER_APP_SGPT2M (0x00cc) -#define U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_SGPT2M_MODE_ONE_SHOT (0x00000001) -/* GP2 Timer Status Register 32bit (R/-) */ -#define U300_TIMER_APP_GPT2S (0x00d0) -#define U300_TIMER_APP_GPT2S_TIMER_STATE_MASK (0x0000000F) -#define U300_TIMER_APP_GPT2S_TIMER_STATE_IDLE (0x00000001) -#define U300_TIMER_APP_GPT2S_TIMER_STATE_ACTIVE (0x00000002) -#define U300_TIMER_APP_GPT2S_ENABLE_IND (0x00000010) -#define U300_TIMER_APP_GPT2S_MODE_MASK (0x00000020) -#define U300_TIMER_APP_GPT2S_MODE_CONTINUOUS (0x00000000) -#define U300_TIMER_APP_GPT2S_MODE_ONE_SHOT (0x00000020) -#define U300_TIMER_APP_GPT2S_IRQ_ENABLED_IND (0x00000040) -#define U300_TIMER_APP_GPT2S_IRQ_PENDING_IND (0x00000080) -/* GP2 Timer Current Count Register 32bit (R/-) */ -#define U300_TIMER_APP_GPT2CC (0x00d4) -/* GP2 Timer Terminal Count Register 32bit (R/W) */ -#define U300_TIMER_APP_GPT2TC (0x00d8) -/* GP2 Timer Interrupt Enable Register 32bit (-/W) */ -#define U300_TIMER_APP_GPT2IE (0x00dc) -#define U300_TIMER_APP_GPT2IE_IRQ_DISABLE (0x00000000) -#define U300_TIMER_APP_GPT2IE_IRQ_ENABLE (0x00000001) -/* GP2 Timer Interrupt Acknowledge Register 32bit (-/W) */ -#define U300_TIMER_APP_GPT2IA (0x00e0) -#define U300_TIMER_APP_GPT2IA_IRQ_ACK (0x00000080) - -/* Clock request control register - all four timers */ -#define U300_TIMER_APP_CRC (0x100) -#define U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE (0x00000001) - -static void __iomem *u300_timer_base; - -struct u300_clockevent_data { - struct clock_event_device cevd; - unsigned ticks_per_jiffy; -}; - -static int u300_shutdown(struct clock_event_device *evt) -{ - /* Disable interrupts on GP1 */ - writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, - u300_timer_base + U300_TIMER_APP_GPT1IE); - /* Disable GP1 */ - writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, - u300_timer_base + U300_TIMER_APP_DGPT1); - return 0; -} - -/* - * If we have oneshot timer active, the oneshot scheduling function - * u300_set_next_event() is called immediately after. - */ -static int u300_set_oneshot(struct clock_event_device *evt) -{ - /* Just return; here? */ - /* - * The actual event will be programmed by the next event hook, - * so we just set a dummy value somewhere at the end of the - * universe here. - */ - /* Disable interrupts on GPT1 */ - writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, - u300_timer_base + U300_TIMER_APP_GPT1IE); - /* Disable GP1 while we're reprogramming it. */ - writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, - u300_timer_base + U300_TIMER_APP_DGPT1); - /* - * Expire far in the future, u300_set_next_event() will be - * called soon... - */ - writel(0xFFFFFFFF, u300_timer_base + U300_TIMER_APP_GPT1TC); - /* We run one shot per tick here! */ - writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT, - u300_timer_base + U300_TIMER_APP_SGPT1M); - /* Enable interrupts for this timer */ - writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE, - u300_timer_base + U300_TIMER_APP_GPT1IE); - /* Enable timer */ - writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE, - u300_timer_base + U300_TIMER_APP_EGPT1); - return 0; -} - -static int u300_set_periodic(struct clock_event_device *evt) -{ - struct u300_clockevent_data *cevdata = - container_of(evt, struct u300_clockevent_data, cevd); - - /* Disable interrupts on GPT1 */ - writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, - u300_timer_base + U300_TIMER_APP_GPT1IE); - /* Disable GP1 while we're reprogramming it. */ - writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, - u300_timer_base + U300_TIMER_APP_DGPT1); - /* - * Set the periodic mode to a certain number of ticks per - * jiffy. - */ - writel(cevdata->ticks_per_jiffy, - u300_timer_base + U300_TIMER_APP_GPT1TC); - /* - * Set continuous mode, so the timer keeps triggering - * interrupts. - */ - writel(U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS, - u300_timer_base + U300_TIMER_APP_SGPT1M); - /* Enable timer interrupts */ - writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE, - u300_timer_base + U300_TIMER_APP_GPT1IE); - /* Then enable the OS timer again */ - writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE, - u300_timer_base + U300_TIMER_APP_EGPT1); - return 0; -} - -/* - * The app timer in one shot mode obviously has to be reprogrammed - * in EXACTLY this sequence to work properly. Do NOT try to e.g. replace - * the interrupt disable + timer disable commands with a reset command, - * it will fail miserably. Apparently (and I found this the hard way) - * the timer is very sensitive to the instruction order, though you don't - * get that impression from the data sheet. - */ -static int u300_set_next_event(unsigned long cycles, - struct clock_event_device *evt) - -{ - /* Disable interrupts on GPT1 */ - writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, - u300_timer_base + U300_TIMER_APP_GPT1IE); - /* Disable GP1 while we're reprogramming it. */ - writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, - u300_timer_base + U300_TIMER_APP_DGPT1); - /* Reset the General Purpose timer 1. */ - writel(U300_TIMER_APP_RGPT1_TIMER_RESET, - u300_timer_base + U300_TIMER_APP_RGPT1); - /* IRQ in n * cycles */ - writel(cycles, u300_timer_base + U300_TIMER_APP_GPT1TC); - /* - * We run one shot per tick here! (This is necessary to reconfigure, - * the timer will tilt if you don't!) - */ - writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT, - u300_timer_base + U300_TIMER_APP_SGPT1M); - /* Enable timer interrupts */ - writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE, - u300_timer_base + U300_TIMER_APP_GPT1IE); - /* Then enable the OS timer again */ - writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE, - u300_timer_base + U300_TIMER_APP_EGPT1); - return 0; -} - -static struct u300_clockevent_data u300_clockevent_data = { - /* Use general purpose timer 1 as clock event */ - .cevd = { - .name = "GPT1", - /* Reasonably fast and accurate clock event */ - .rating = 300, - .features = CLOCK_EVT_FEAT_PERIODIC | - CLOCK_EVT_FEAT_ONESHOT, - .set_next_event = u300_set_next_event, - .set_state_shutdown = u300_shutdown, - .set_state_periodic = u300_set_periodic, - .set_state_oneshot = u300_set_oneshot, - }, -}; - -/* Clock event timer interrupt handler */ -static irqreturn_t u300_timer_interrupt(int irq, void *dev_id) -{ - struct clock_event_device *evt = &u300_clockevent_data.cevd; - /* ACK/Clear timer IRQ for the APP GPT1 Timer */ - - writel(U300_TIMER_APP_GPT1IA_IRQ_ACK, - u300_timer_base + U300_TIMER_APP_GPT1IA); - evt->event_handler(evt); - return IRQ_HANDLED; -} - -/* - * Override the global weak sched_clock symbol with this - * local implementation which uses the clocksource to get some - * better resolution when scheduling the kernel. We accept that - * this wraps around for now, since it is just a relative time - * stamp. (Inspired by OMAP implementation.) - */ - -static u64 notrace u300_read_sched_clock(void) -{ - return readl(u300_timer_base + U300_TIMER_APP_GPT2CC); -} - -static unsigned long u300_read_current_timer(void) -{ - return readl(u300_timer_base + U300_TIMER_APP_GPT2CC); -} - -static struct delay_timer u300_delay_timer; - -/* - * This sets up the system timers, clock source and clock event. - */ -static int __init u300_timer_init_of(struct device_node *np) -{ - unsigned int irq; - struct clk *clk; - unsigned long rate; - int ret; - - u300_timer_base = of_iomap(np, 0); - if (!u300_timer_base) { - pr_err("could not ioremap system timer\n"); - return -ENXIO; - } - - /* Get the IRQ for the GP1 timer */ - irq = irq_of_parse_and_map(np, 2); - if (!irq) { - pr_err("no IRQ for system timer\n"); - return -EINVAL; - } - - pr_info("U300 GP1 timer @ base: %p, IRQ: %u\n", u300_timer_base, irq); - - /* Clock the interrupt controller */ - clk = of_clk_get(np, 0); - if (IS_ERR(clk)) - return PTR_ERR(clk); - - ret = clk_prepare_enable(clk); - if (ret) - return ret; - - rate = clk_get_rate(clk); - - u300_clockevent_data.ticks_per_jiffy = DIV_ROUND_CLOSEST(rate, HZ); - - sched_clock_register(u300_read_sched_clock, 32, rate); - - u300_delay_timer.read_current_timer = &u300_read_current_timer; - u300_delay_timer.freq = rate; - register_current_timer_delay(&u300_delay_timer); - - /* - * Disable the "OS" and "DD" timers - these are designed for Symbian! - * Example usage in cnh1601578 cpu subsystem pd_timer_app.c - */ - writel(U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE, - u300_timer_base + U300_TIMER_APP_CRC); - writel(U300_TIMER_APP_ROST_TIMER_RESET, - u300_timer_base + U300_TIMER_APP_ROST); - writel(U300_TIMER_APP_DOST_TIMER_DISABLE, - u300_timer_base + U300_TIMER_APP_DOST); - writel(U300_TIMER_APP_RDDT_TIMER_RESET, - u300_timer_base + U300_TIMER_APP_RDDT); - writel(U300_TIMER_APP_DDDT_TIMER_DISABLE, - u300_timer_base + U300_TIMER_APP_DDDT); - - /* Reset the General Purpose timer 1. */ - writel(U300_TIMER_APP_RGPT1_TIMER_RESET, - u300_timer_base + U300_TIMER_APP_RGPT1); - - /* Set up the IRQ handler */ - ret = request_irq(irq, u300_timer_interrupt, - IRQF_TIMER | IRQF_IRQPOLL, "U300 Timer Tick", NULL); - if (ret) - return ret; - - /* Reset the General Purpose timer 2 */ - writel(U300_TIMER_APP_RGPT2_TIMER_RESET, - u300_timer_base + U300_TIMER_APP_RGPT2); - /* Set this timer to run around forever */ - writel(0xFFFFFFFFU, u300_timer_base + U300_TIMER_APP_GPT2TC); - /* Set continuous mode so it wraps around */ - writel(U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS, - u300_timer_base + U300_TIMER_APP_SGPT2M); - /* Disable timer interrupts */ - writel(U300_TIMER_APP_GPT2IE_IRQ_DISABLE, - u300_timer_base + U300_TIMER_APP_GPT2IE); - /* Then enable the GP2 timer to use as a free running us counter */ - writel(U300_TIMER_APP_EGPT2_TIMER_ENABLE, - u300_timer_base + U300_TIMER_APP_EGPT2); - - /* Use general purpose timer 2 as clock source */ - ret = clocksource_mmio_init(u300_timer_base + U300_TIMER_APP_GPT2CC, - "GPT2", rate, 300, 32, clocksource_mmio_readl_up); - if (ret) { - pr_err("timer: failed to initialize U300 clock source\n"); - return ret; - } - - /* Configure and register the clockevent */ - clockevents_config_and_register(&u300_clockevent_data.cevd, rate, - 1, 0xffffffff); - - /* - * TODO: init and register the rest of the timers too, they can be - * used by hrtimers! - */ - return 0; -} - -TIMER_OF_DECLARE(u300_timer, "stericsson,u300-apptimer", - u300_timer_init_of); |