diff options
Diffstat (limited to 'include/drm')
37 files changed, 1077 insertions, 916 deletions
diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h index 2a1f85f9a8a3..f668e75fbabe 100644 --- a/include/drm/bridge/dw_hdmi.h +++ b/include/drm/bridge/dw_hdmi.h @@ -143,6 +143,11 @@ struct dw_hdmi_plat_data { const struct drm_display_info *info, const struct drm_display_mode *mode); + /* Platform-specific audio enable/disable (optional) */ + void (*enable_audio)(struct dw_hdmi *hdmi, int channel, + int width, int rate, int non_pcm); + void (*disable_audio)(struct dw_hdmi *hdmi); + /* Vendor PHY support */ const struct dw_hdmi_phy_ops *phy_ops; const char *phy_name; @@ -173,6 +178,8 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense); int dw_hdmi_set_plugged_cb(struct dw_hdmi *hdmi, hdmi_codec_plugged_cb fn, struct device *codec_dev); +void dw_hdmi_set_sample_non_pcm(struct dw_hdmi *hdmi, unsigned int non_pcm); +void dw_hdmi_set_sample_width(struct dw_hdmi *hdmi, unsigned int width); void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate); void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt); void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi, u8 *channel_status); @@ -187,9 +194,11 @@ void dw_hdmi_phy_i2c_set_addr(struct dw_hdmi *hdmi, u8 address); void dw_hdmi_phy_i2c_write(struct dw_hdmi *hdmi, unsigned short data, unsigned char addr); +void dw_hdmi_phy_gen1_reset(struct dw_hdmi *hdmi); + void dw_hdmi_phy_gen2_pddq(struct dw_hdmi *hdmi, u8 enable); void dw_hdmi_phy_gen2_txpwron(struct dw_hdmi *hdmi, u8 enable); -void dw_hdmi_phy_reset(struct dw_hdmi *hdmi); +void dw_hdmi_phy_gen2_reset(struct dw_hdmi *hdmi); enum drm_connector_status dw_hdmi_phy_read_hpd(struct dw_hdmi *hdmi, void *data); diff --git a/include/drm/dp/drm_dp_helper.h b/include/drm/display/drm_dp.h index 51e02cf75277..9e3aff7e68bb 100644 --- a/include/drm/dp/drm_dp_helper.h +++ b/include/drm/display/drm_dp.h @@ -20,17 +20,10 @@ * OF THIS SOFTWARE. */ -#ifndef _DRM_DP_HELPER_H_ -#define _DRM_DP_HELPER_H_ +#ifndef _DRM_DP_H_ +#define _DRM_DP_H_ -#include <linux/delay.h> -#include <linux/i2c.h> #include <linux/types.h> -#include <drm/drm_connector.h> - -struct drm_device; -struct drm_dp_aux; -struct drm_panel; /* * Unless otherwise noted, all values are from the DP 1.1a spec. Note that @@ -361,6 +354,7 @@ struct drm_panel; # define DP_PSR_IS_SUPPORTED 1 # define DP_PSR2_IS_SUPPORTED 2 /* eDP 1.4 */ # define DP_PSR2_WITH_Y_COORD_IS_SUPPORTED 3 /* eDP 1.4a */ +# define DP_PSR2_WITH_Y_COORD_ET_SUPPORTED 4 /* eDP 1.5, adopted eDP 1.4b SCR */ #define DP_PSR_CAPS 0x071 /* XXX 1.2? */ # define DP_PSR_NO_TRAIN_ON_EXIT 1 @@ -375,6 +369,7 @@ struct drm_panel; # define DP_PSR_SETUP_TIME_SHIFT 1 # define DP_PSR2_SU_Y_COORDINATE_REQUIRED (1 << 4) /* eDP 1.4a */ # define DP_PSR2_SU_GRANULARITY_REQUIRED (1 << 5) /* eDP 1.4b */ +# define DP_PSR2_SU_AUX_FRAME_SYNC_NOT_NEEDED (1 << 6)/* eDP 1.5, adopted eDP 1.4b SCR */ #define DP_PSR2_SU_X_GRANULARITY 0x072 /* eDP 1.4b */ #define DP_PSR2_SU_Y_GRANULARITY 0x074 /* eDP 1.4b */ @@ -1520,16 +1515,6 @@ enum drm_dp_phy { #define DP_LINK_CONSTANT_N_VALUE 0x8000 #define DP_LINK_STATUS_SIZE 6 -bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE], - int lane_count); -bool drm_dp_clock_recovery_ok(const u8 link_status[DP_LINK_STATUS_SIZE], - int lane_count); -u8 drm_dp_get_adjust_request_voltage(const u8 link_status[DP_LINK_STATUS_SIZE], - int lane); -u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SIZE], - int lane); -u8 drm_dp_get_adjust_tx_ffe_preset(const u8 link_status[DP_LINK_STATUS_SIZE], - int lane); #define DP_BRANCH_OUI_HEADER_SIZE 0xc #define DP_RECEIVER_CAP_SIZE 0xf @@ -1539,31 +1524,6 @@ u8 drm_dp_get_adjust_tx_ffe_preset(const u8 link_status[DP_LINK_STATUS_SIZE], #define DP_LTTPR_COMMON_CAP_SIZE 8 #define DP_LTTPR_PHY_CAP_SIZE 3 -int drm_dp_read_clock_recovery_delay(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], - enum drm_dp_phy dp_phy, bool uhbr); -int drm_dp_read_channel_eq_delay(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], - enum drm_dp_phy dp_phy, bool uhbr); - -void drm_dp_link_train_clock_recovery_delay(const struct drm_dp_aux *aux, - const u8 dpcd[DP_RECEIVER_CAP_SIZE]); -void drm_dp_lttpr_link_train_clock_recovery_delay(void); -void drm_dp_link_train_channel_eq_delay(const struct drm_dp_aux *aux, - const u8 dpcd[DP_RECEIVER_CAP_SIZE]); -void drm_dp_lttpr_link_train_channel_eq_delay(const struct drm_dp_aux *aux, - const u8 caps[DP_LTTPR_PHY_CAP_SIZE]); - -int drm_dp_128b132b_read_aux_rd_interval(struct drm_dp_aux *aux); -bool drm_dp_128b132b_lane_channel_eq_done(const u8 link_status[DP_LINK_STATUS_SIZE], - int lane_count); -bool drm_dp_128b132b_lane_symbol_locked(const u8 link_status[DP_LINK_STATUS_SIZE], - int lane_count); -bool drm_dp_128b132b_eq_interlane_align_done(const u8 link_status[DP_LINK_STATUS_SIZE]); -bool drm_dp_128b132b_cds_interlane_align_done(const u8 link_status[DP_LINK_STATUS_SIZE]); -bool drm_dp_128b132b_link_training_failed(const u8 link_status[DP_LINK_STATUS_SIZE]); - -u8 drm_dp_link_rate_to_bw_code(int link_rate); -int drm_dp_bw_code_to_link_rate(u8 link_bw); - #define DP_SDP_AUDIO_TIMESTAMP 0x01 #define DP_SDP_AUDIO_STREAM 0x02 #define DP_SDP_EXTENSION 0x04 /* DP 1.1 */ @@ -1727,651 +1687,4 @@ enum dp_content_type { DP_CONTENT_TYPE_GAME = 0x04, }; -/** - * struct drm_dp_vsc_sdp - drm DP VSC SDP - * - * This structure represents a DP VSC SDP of drm - * It is based on DP 1.4 spec [Table 2-116: VSC SDP Header Bytes] and - * [Table 2-117: VSC SDP Payload for DB16 through DB18] - * - * @sdp_type: secondary-data packet type - * @revision: revision number - * @length: number of valid data bytes - * @pixelformat: pixel encoding format - * @colorimetry: colorimetry format - * @bpc: bit per color - * @dynamic_range: dynamic range information - * @content_type: CTA-861-G defines content types and expected processing by a sink device - */ -struct drm_dp_vsc_sdp { - unsigned char sdp_type; - unsigned char revision; - unsigned char length; - enum dp_pixelformat pixelformat; - enum dp_colorimetry colorimetry; - int bpc; - enum dp_dynamic_range dynamic_range; - enum dp_content_type content_type; -}; - -void drm_dp_vsc_sdp_log(const char *level, struct device *dev, - const struct drm_dp_vsc_sdp *vsc); - -int drm_dp_psr_setup_time(const u8 psr_cap[EDP_PSR_RECEIVER_CAP_SIZE]); - -static inline int -drm_dp_max_link_rate(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return drm_dp_bw_code_to_link_rate(dpcd[DP_MAX_LINK_RATE]); -} - -static inline u8 -drm_dp_max_lane_count(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_MAX_LANE_COUNT] & DP_MAX_LANE_COUNT_MASK; -} - -static inline bool -drm_dp_enhanced_frame_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_DPCD_REV] >= 0x11 && - (dpcd[DP_MAX_LANE_COUNT] & DP_ENHANCED_FRAME_CAP); -} - -static inline bool -drm_dp_fast_training_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_DPCD_REV] >= 0x11 && - (dpcd[DP_MAX_DOWNSPREAD] & DP_NO_AUX_HANDSHAKE_LINK_TRAINING); -} - -static inline bool -drm_dp_tps3_supported(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_DPCD_REV] >= 0x12 && - dpcd[DP_MAX_LANE_COUNT] & DP_TPS3_SUPPORTED; -} - -static inline bool -drm_dp_max_downspread(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_DPCD_REV] >= 0x11 || - dpcd[DP_MAX_DOWNSPREAD] & DP_MAX_DOWNSPREAD_0_5; -} - -static inline bool -drm_dp_tps4_supported(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_DPCD_REV] >= 0x14 && - dpcd[DP_MAX_DOWNSPREAD] & DP_TPS4_SUPPORTED; -} - -static inline u8 -drm_dp_training_pattern_mask(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return (dpcd[DP_DPCD_REV] >= 0x14) ? DP_TRAINING_PATTERN_MASK_1_4 : - DP_TRAINING_PATTERN_MASK; -} - -static inline bool -drm_dp_is_branch(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_DOWNSTREAMPORT_PRESENT] & DP_DWN_STRM_PORT_PRESENT; -} - -/* DP/eDP DSC support */ -u8 drm_dp_dsc_sink_max_slice_count(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE], - bool is_edp); -u8 drm_dp_dsc_sink_line_buf_depth(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]); -int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpc[DP_DSC_RECEIVER_CAP_SIZE], - u8 dsc_bpc[3]); - -static inline bool -drm_dp_sink_supports_dsc(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]) -{ - return dsc_dpcd[DP_DSC_SUPPORT - DP_DSC_SUPPORT] & - DP_DSC_DECOMPRESSION_IS_SUPPORTED; -} - -static inline u16 -drm_edp_dsc_sink_output_bpp(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]) -{ - return dsc_dpcd[DP_DSC_MAX_BITS_PER_PIXEL_LOW - DP_DSC_SUPPORT] | - (dsc_dpcd[DP_DSC_MAX_BITS_PER_PIXEL_HI - DP_DSC_SUPPORT] & - DP_DSC_MAX_BITS_PER_PIXEL_HI_MASK << - DP_DSC_MAX_BITS_PER_PIXEL_HI_SHIFT); -} - -static inline u32 -drm_dp_dsc_sink_max_slice_width(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]) -{ - /* Max Slicewidth = Number of Pixels * 320 */ - return dsc_dpcd[DP_DSC_MAX_SLICE_WIDTH - DP_DSC_SUPPORT] * - DP_DSC_SLICE_WIDTH_MULTIPLIER; -} - -/* Forward Error Correction Support on DP 1.4 */ -static inline bool -drm_dp_sink_supports_fec(const u8 fec_capable) -{ - return fec_capable & DP_FEC_CAPABLE; -} - -static inline bool -drm_dp_channel_coding_supported(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_MAIN_LINK_CHANNEL_CODING] & DP_CAP_ANSI_8B10B; -} - -static inline bool -drm_dp_alternate_scrambler_reset_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_EDP_CONFIGURATION_CAP] & - DP_ALTERNATE_SCRAMBLER_RESET_CAP; -} - -/* Ignore MSA timing for Adaptive Sync support on DP 1.4 */ -static inline bool -drm_dp_sink_can_do_video_without_timing_msa(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) -{ - return dpcd[DP_DOWN_STREAM_PORT_COUNT] & - DP_MSA_TIMING_PAR_IGNORED; -} - -/** - * drm_edp_backlight_supported() - Check an eDP DPCD for VESA backlight support - * @edp_dpcd: The DPCD to check - * - * Note that currently this function will return %false for panels which support various DPCD - * backlight features but which require the brightness be set through PWM, and don't support setting - * the brightness level via the DPCD. - * - * Returns: %True if @edp_dpcd indicates that VESA backlight controls are supported, %false - * otherwise - */ -static inline bool -drm_edp_backlight_supported(const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE]) -{ - return !!(edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP); -} - -/* - * DisplayPort AUX channel - */ - -/** - * struct drm_dp_aux_msg - DisplayPort AUX channel transaction - * @address: address of the (first) register to access - * @request: contains the type of transaction (see DP_AUX_* macros) - * @reply: upon completion, contains the reply type of the transaction - * @buffer: pointer to a transmission or reception buffer - * @size: size of @buffer - */ -struct drm_dp_aux_msg { - unsigned int address; - u8 request; - u8 reply; - void *buffer; - size_t size; -}; - -struct cec_adapter; -struct edid; -struct drm_connector; - -/** - * struct drm_dp_aux_cec - DisplayPort CEC-Tunneling-over-AUX - * @lock: mutex protecting this struct - * @adap: the CEC adapter for CEC-Tunneling-over-AUX support. - * @connector: the connector this CEC adapter is associated with - * @unregister_work: unregister the CEC adapter - */ -struct drm_dp_aux_cec { - struct mutex lock; - struct cec_adapter *adap; - struct drm_connector *connector; - struct delayed_work unregister_work; -}; - -/** - * struct drm_dp_aux - DisplayPort AUX channel - * - * An AUX channel can also be used to transport I2C messages to a sink. A - * typical application of that is to access an EDID that's present in the sink - * device. The @transfer() function can also be used to execute such - * transactions. The drm_dp_aux_register() function registers an I2C adapter - * that can be passed to drm_probe_ddc(). Upon removal, drivers should call - * drm_dp_aux_unregister() to remove the I2C adapter. The I2C adapter uses long - * transfers by default; if a partial response is received, the adapter will - * drop down to the size given by the partial response for this transaction - * only. - */ -struct drm_dp_aux { - /** - * @name: user-visible name of this AUX channel and the - * I2C-over-AUX adapter. - * - * It's also used to specify the name of the I2C adapter. If set - * to %NULL, dev_name() of @dev will be used. - */ - const char *name; - - /** - * @ddc: I2C adapter that can be used for I2C-over-AUX - * communication - */ - struct i2c_adapter ddc; - - /** - * @dev: pointer to struct device that is the parent for this - * AUX channel. - */ - struct device *dev; - - /** - * @drm_dev: pointer to the &drm_device that owns this AUX channel. - * Beware, this may be %NULL before drm_dp_aux_register() has been - * called. - * - * It should be set to the &drm_device that will be using this AUX - * channel as early as possible. For many graphics drivers this should - * happen before drm_dp_aux_init(), however it's perfectly fine to set - * this field later so long as it's assigned before calling - * drm_dp_aux_register(). - */ - struct drm_device *drm_dev; - - /** - * @crtc: backpointer to the crtc that is currently using this - * AUX channel - */ - struct drm_crtc *crtc; - - /** - * @hw_mutex: internal mutex used for locking transfers. - * - * Note that if the underlying hardware is shared among multiple - * channels, the driver needs to do additional locking to - * prevent concurrent access. - */ - struct mutex hw_mutex; - - /** - * @crc_work: worker that captures CRCs for each frame - */ - struct work_struct crc_work; - - /** - * @crc_count: counter of captured frame CRCs - */ - u8 crc_count; - - /** - * @transfer: transfers a message representing a single AUX - * transaction. - * - * This is a hardware-specific implementation of how - * transactions are executed that the drivers must provide. - * - * A pointer to a &drm_dp_aux_msg structure describing the - * transaction is passed into this function. Upon success, the - * implementation should return the number of payload bytes that - * were transferred, or a negative error-code on failure. - * - * Helpers will propagate these errors, with the exception of - * the %-EBUSY error, which causes a transaction to be retried. - * On a short, helpers will return %-EPROTO to make it simpler - * to check for failure. - * - * The @transfer() function must only modify the reply field of - * the &drm_dp_aux_msg structure. The retry logic and i2c - * helpers assume this is the case. - * - * Also note that this callback can be called no matter the - * state @dev is in. Drivers that need that device to be powered - * to perform this operation will first need to make sure it's - * been properly enabled. - */ - ssize_t (*transfer)(struct drm_dp_aux *aux, - struct drm_dp_aux_msg *msg); - - /** - * @i2c_nack_count: Counts I2C NACKs, used for DP validation. - */ - unsigned i2c_nack_count; - /** - * @i2c_defer_count: Counts I2C DEFERs, used for DP validation. - */ - unsigned i2c_defer_count; - /** - * @cec: struct containing fields used for CEC-Tunneling-over-AUX. - */ - struct drm_dp_aux_cec cec; - /** - * @is_remote: Is this AUX CH actually using sideband messaging. - */ - bool is_remote; -}; - -ssize_t drm_dp_dpcd_read(struct drm_dp_aux *aux, unsigned int offset, - void *buffer, size_t size); -ssize_t drm_dp_dpcd_write(struct drm_dp_aux *aux, unsigned int offset, - void *buffer, size_t size); - -/** - * drm_dp_dpcd_readb() - read a single byte from the DPCD - * @aux: DisplayPort AUX channel - * @offset: address of the register to read - * @valuep: location where the value of the register will be stored - * - * Returns the number of bytes transferred (1) on success, or a negative - * error code on failure. - */ -static inline ssize_t drm_dp_dpcd_readb(struct drm_dp_aux *aux, - unsigned int offset, u8 *valuep) -{ - return drm_dp_dpcd_read(aux, offset, valuep, 1); -} - -/** - * drm_dp_dpcd_writeb() - write a single byte to the DPCD - * @aux: DisplayPort AUX channel - * @offset: address of the register to write - * @value: value to write to the register - * - * Returns the number of bytes transferred (1) on success, or a negative - * error code on failure. - */ -static inline ssize_t drm_dp_dpcd_writeb(struct drm_dp_aux *aux, - unsigned int offset, u8 value) -{ - return drm_dp_dpcd_write(aux, offset, &value, 1); -} - -int drm_dp_read_dpcd_caps(struct drm_dp_aux *aux, - u8 dpcd[DP_RECEIVER_CAP_SIZE]); - -int drm_dp_dpcd_read_link_status(struct drm_dp_aux *aux, - u8 status[DP_LINK_STATUS_SIZE]); - -int drm_dp_dpcd_read_phy_link_status(struct drm_dp_aux *aux, - enum drm_dp_phy dp_phy, - u8 link_status[DP_LINK_STATUS_SIZE]); - -bool drm_dp_send_real_edid_checksum(struct drm_dp_aux *aux, - u8 real_edid_checksum); - -int drm_dp_read_downstream_info(struct drm_dp_aux *aux, - const u8 dpcd[DP_RECEIVER_CAP_SIZE], - u8 downstream_ports[DP_MAX_DOWNSTREAM_PORTS]); -bool drm_dp_downstream_is_type(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4], u8 type); -bool drm_dp_downstream_is_tmds(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4], - const struct edid *edid); -int drm_dp_downstream_max_dotclock(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4]); -int drm_dp_downstream_max_tmds_clock(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4], - const struct edid *edid); -int drm_dp_downstream_min_tmds_clock(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4], - const struct edid *edid); -int drm_dp_downstream_max_bpc(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4], - const struct edid *edid); -bool drm_dp_downstream_420_passthrough(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4]); -bool drm_dp_downstream_444_to_420_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4]); -struct drm_display_mode *drm_dp_downstream_mode(struct drm_device *dev, - const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4]); -int drm_dp_downstream_id(struct drm_dp_aux *aux, char id[6]); -void drm_dp_downstream_debug(struct seq_file *m, - const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4], - const struct edid *edid, - struct drm_dp_aux *aux); -enum drm_mode_subconnector -drm_dp_subconnector_type(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4]); -void drm_dp_set_subconnector_property(struct drm_connector *connector, - enum drm_connector_status status, - const u8 *dpcd, - const u8 port_cap[4]); - -struct drm_dp_desc; -bool drm_dp_read_sink_count_cap(struct drm_connector *connector, - const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const struct drm_dp_desc *desc); -int drm_dp_read_sink_count(struct drm_dp_aux *aux); - -int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux, - u8 caps[DP_LTTPR_COMMON_CAP_SIZE]); -int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux, - enum drm_dp_phy dp_phy, - u8 caps[DP_LTTPR_PHY_CAP_SIZE]); -int drm_dp_lttpr_count(const u8 cap[DP_LTTPR_COMMON_CAP_SIZE]); -int drm_dp_lttpr_max_link_rate(const u8 caps[DP_LTTPR_COMMON_CAP_SIZE]); -int drm_dp_lttpr_max_lane_count(const u8 caps[DP_LTTPR_COMMON_CAP_SIZE]); -bool drm_dp_lttpr_voltage_swing_level_3_supported(const u8 caps[DP_LTTPR_PHY_CAP_SIZE]); -bool drm_dp_lttpr_pre_emphasis_level_3_supported(const u8 caps[DP_LTTPR_PHY_CAP_SIZE]); - -void drm_dp_remote_aux_init(struct drm_dp_aux *aux); -void drm_dp_aux_init(struct drm_dp_aux *aux); -int drm_dp_aux_register(struct drm_dp_aux *aux); -void drm_dp_aux_unregister(struct drm_dp_aux *aux); - -int drm_dp_start_crc(struct drm_dp_aux *aux, struct drm_crtc *crtc); -int drm_dp_stop_crc(struct drm_dp_aux *aux); - -struct drm_dp_dpcd_ident { - u8 oui[3]; - u8 device_id[6]; - u8 hw_rev; - u8 sw_major_rev; - u8 sw_minor_rev; -} __packed; - -/** - * struct drm_dp_desc - DP branch/sink device descriptor - * @ident: DP device identification from DPCD 0x400 (sink) or 0x500 (branch). - * @quirks: Quirks; use drm_dp_has_quirk() to query for the quirks. - */ -struct drm_dp_desc { - struct drm_dp_dpcd_ident ident; - u32 quirks; -}; - -int drm_dp_read_desc(struct drm_dp_aux *aux, struct drm_dp_desc *desc, - bool is_branch); - -/** - * enum drm_dp_quirk - Display Port sink/branch device specific quirks - * - * Display Port sink and branch devices in the wild have a variety of bugs, try - * to collect them here. The quirks are shared, but it's up to the drivers to - * implement workarounds for them. - */ -enum drm_dp_quirk { - /** - * @DP_DPCD_QUIRK_CONSTANT_N: - * - * The device requires main link attributes Mvid and Nvid to be limited - * to 16 bits. So will give a constant value (0x8000) for compatability. - */ - DP_DPCD_QUIRK_CONSTANT_N, - /** - * @DP_DPCD_QUIRK_NO_PSR: - * - * The device does not support PSR even if reports that it supports or - * driver still need to implement proper handling for such device. - */ - DP_DPCD_QUIRK_NO_PSR, - /** - * @DP_DPCD_QUIRK_NO_SINK_COUNT: - * - * The device does not set SINK_COUNT to a non-zero value. - * The driver should ignore SINK_COUNT during detection. Note that - * drm_dp_read_sink_count_cap() automatically checks for this quirk. - */ - DP_DPCD_QUIRK_NO_SINK_COUNT, - /** - * @DP_DPCD_QUIRK_DSC_WITHOUT_VIRTUAL_DPCD: - * - * The device supports MST DSC despite not supporting Virtual DPCD. - * The DSC caps can be read from the physical aux instead. - */ - DP_DPCD_QUIRK_DSC_WITHOUT_VIRTUAL_DPCD, - /** - * @DP_DPCD_QUIRK_CAN_DO_MAX_LINK_RATE_3_24_GBPS: - * - * The device supports a link rate of 3.24 Gbps (multiplier 0xc) despite - * the DP_MAX_LINK_RATE register reporting a lower max multiplier. - */ - DP_DPCD_QUIRK_CAN_DO_MAX_LINK_RATE_3_24_GBPS, -}; - -/** - * drm_dp_has_quirk() - does the DP device have a specific quirk - * @desc: Device descriptor filled by drm_dp_read_desc() - * @quirk: Quirk to query for - * - * Return true if DP device identified by @desc has @quirk. - */ -static inline bool -drm_dp_has_quirk(const struct drm_dp_desc *desc, enum drm_dp_quirk quirk) -{ - return desc->quirks & BIT(quirk); -} - -/** - * struct drm_edp_backlight_info - Probed eDP backlight info struct - * @pwmgen_bit_count: The pwmgen bit count - * @pwm_freq_pre_divider: The PWM frequency pre-divider value being used for this backlight, if any - * @max: The maximum backlight level that may be set - * @lsb_reg_used: Do we also write values to the DP_EDP_BACKLIGHT_BRIGHTNESS_LSB register? - * @aux_enable: Does the panel support the AUX enable cap? - * @aux_set: Does the panel support setting the brightness through AUX? - * - * This structure contains various data about an eDP backlight, which can be populated by using - * drm_edp_backlight_init(). - */ -struct drm_edp_backlight_info { - u8 pwmgen_bit_count; - u8 pwm_freq_pre_divider; - u16 max; - - bool lsb_reg_used : 1; - bool aux_enable : 1; - bool aux_set : 1; -}; - -int -drm_edp_backlight_init(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, - u16 driver_pwm_freq_hz, const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE], - u16 *current_level, u8 *current_mode); -int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, - u16 level); -int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, - u16 level); -int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl); - -#if IS_ENABLED(CONFIG_DRM_KMS_HELPER) && (IS_BUILTIN(CONFIG_BACKLIGHT_CLASS_DEVICE) || \ - (IS_MODULE(CONFIG_DRM_KMS_HELPER) && IS_MODULE(CONFIG_BACKLIGHT_CLASS_DEVICE))) - -int drm_panel_dp_aux_backlight(struct drm_panel *panel, struct drm_dp_aux *aux); - -#else - -static inline int drm_panel_dp_aux_backlight(struct drm_panel *panel, - struct drm_dp_aux *aux) -{ - return 0; -} - -#endif - -#ifdef CONFIG_DRM_DP_CEC -void drm_dp_cec_irq(struct drm_dp_aux *aux); -void drm_dp_cec_register_connector(struct drm_dp_aux *aux, - struct drm_connector *connector); -void drm_dp_cec_unregister_connector(struct drm_dp_aux *aux); -void drm_dp_cec_set_edid(struct drm_dp_aux *aux, const struct edid *edid); -void drm_dp_cec_unset_edid(struct drm_dp_aux *aux); -#else -static inline void drm_dp_cec_irq(struct drm_dp_aux *aux) -{ -} - -static inline void -drm_dp_cec_register_connector(struct drm_dp_aux *aux, - struct drm_connector *connector) -{ -} - -static inline void drm_dp_cec_unregister_connector(struct drm_dp_aux *aux) -{ -} - -static inline void drm_dp_cec_set_edid(struct drm_dp_aux *aux, - const struct edid *edid) -{ -} - -static inline void drm_dp_cec_unset_edid(struct drm_dp_aux *aux) -{ -} - -#endif - -/** - * struct drm_dp_phy_test_params - DP Phy Compliance parameters - * @link_rate: Requested Link rate from DPCD 0x219 - * @num_lanes: Number of lanes requested by sing through DPCD 0x220 - * @phy_pattern: DP Phy test pattern from DPCD 0x248 - * @hbr2_reset: DP HBR2_COMPLIANCE_SCRAMBLER_RESET from DCPD 0x24A and 0x24B - * @custom80: DP Test_80BIT_CUSTOM_PATTERN from DPCDs 0x250 through 0x259 - * @enhanced_frame_cap: flag for enhanced frame capability. - */ -struct drm_dp_phy_test_params { - int link_rate; - u8 num_lanes; - u8 phy_pattern; - u8 hbr2_reset[2]; - u8 custom80[10]; - bool enhanced_frame_cap; -}; - -int drm_dp_get_phy_test_pattern(struct drm_dp_aux *aux, - struct drm_dp_phy_test_params *data); -int drm_dp_set_phy_test_pattern(struct drm_dp_aux *aux, - struct drm_dp_phy_test_params *data, u8 dp_rev); -int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4]); -int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool enable_frl_ready_hpd); -bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux); -int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps, - u8 frl_mode); -int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask, - u8 frl_type); -int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux); -int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux); - -bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux); -int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask); -void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux, - struct drm_connector *connector); -bool drm_dp_pcon_enc_is_dsc_1_2(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); -int drm_dp_pcon_dsc_max_slices(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); -int drm_dp_pcon_dsc_max_slice_width(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); -int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); -int drm_dp_pcon_pps_default(struct drm_dp_aux *aux); -int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128]); -int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6]); -bool drm_dp_downstream_rgb_to_ycbcr_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE], - const u8 port_cap[4], u8 color_spc); -int drm_dp_pcon_convert_rgb_to_ycbcr(struct drm_dp_aux *aux, u8 color_spc); - -#endif /* _DRM_DP_HELPER_H_ */ +#endif /* _DRM_DP_H_ */ diff --git a/include/drm/dp/drm_dp_aux_bus.h b/include/drm/display/drm_dp_aux_bus.h index 4f19b20b1dd6..4f19b20b1dd6 100644 --- a/include/drm/dp/drm_dp_aux_bus.h +++ b/include/drm/display/drm_dp_aux_bus.h diff --git a/include/drm/dp/drm_dp_dual_mode_helper.h b/include/drm/display/drm_dp_dual_mode_helper.h index 7ee482265087..7ee482265087 100644 --- a/include/drm/dp/drm_dp_dual_mode_helper.h +++ b/include/drm/display/drm_dp_dual_mode_helper.h diff --git a/include/drm/display/drm_dp_helper.h b/include/drm/display/drm_dp_helper.h new file mode 100644 index 000000000000..dca40a045dd6 --- /dev/null +++ b/include/drm/display/drm_dp_helper.h @@ -0,0 +1,722 @@ +/* + * Copyright © 2008 Keith Packard + * + * Permission to use, copy, modify, distribute, and sell this software and its + * documentation for any purpose is hereby granted without fee, provided that + * the above copyright notice appear in all copies and that both that copyright + * notice and this permission notice appear in supporting documentation, and + * that the name of the copyright holders not be used in advertising or + * publicity pertaining to distribution of the software without specific, + * written prior permission. The copyright holders make no representations + * about the suitability of this software for any purpose. It is provided "as + * is" without express or implied warranty. + * + * THE COPYRIGHT HOLDERS DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, + * INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO + * EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE FOR ANY SPECIAL, INDIRECT OR + * CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, + * DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER + * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE + * OF THIS SOFTWARE. + */ + +#ifndef _DRM_DP_HELPER_H_ +#define _DRM_DP_HELPER_H_ + +#include <linux/delay.h> +#include <linux/i2c.h> + +#include <drm/display/drm_dp.h> +#include <drm/drm_connector.h> + +struct drm_device; +struct drm_dp_aux; +struct drm_panel; + +bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE], + int lane_count); +bool drm_dp_clock_recovery_ok(const u8 link_status[DP_LINK_STATUS_SIZE], + int lane_count); +u8 drm_dp_get_adjust_request_voltage(const u8 link_status[DP_LINK_STATUS_SIZE], + int lane); +u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SIZE], + int lane); +u8 drm_dp_get_adjust_tx_ffe_preset(const u8 link_status[DP_LINK_STATUS_SIZE], + int lane); + +int drm_dp_read_clock_recovery_delay(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], + enum drm_dp_phy dp_phy, bool uhbr); +int drm_dp_read_channel_eq_delay(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], + enum drm_dp_phy dp_phy, bool uhbr); + +void drm_dp_link_train_clock_recovery_delay(const struct drm_dp_aux *aux, + const u8 dpcd[DP_RECEIVER_CAP_SIZE]); +void drm_dp_lttpr_link_train_clock_recovery_delay(void); +void drm_dp_link_train_channel_eq_delay(const struct drm_dp_aux *aux, + const u8 dpcd[DP_RECEIVER_CAP_SIZE]); +void drm_dp_lttpr_link_train_channel_eq_delay(const struct drm_dp_aux *aux, + const u8 caps[DP_LTTPR_PHY_CAP_SIZE]); + +int drm_dp_128b132b_read_aux_rd_interval(struct drm_dp_aux *aux); +bool drm_dp_128b132b_lane_channel_eq_done(const u8 link_status[DP_LINK_STATUS_SIZE], + int lane_count); +bool drm_dp_128b132b_lane_symbol_locked(const u8 link_status[DP_LINK_STATUS_SIZE], + int lane_count); +bool drm_dp_128b132b_eq_interlane_align_done(const u8 link_status[DP_LINK_STATUS_SIZE]); +bool drm_dp_128b132b_cds_interlane_align_done(const u8 link_status[DP_LINK_STATUS_SIZE]); +bool drm_dp_128b132b_link_training_failed(const u8 link_status[DP_LINK_STATUS_SIZE]); + +u8 drm_dp_link_rate_to_bw_code(int link_rate); +int drm_dp_bw_code_to_link_rate(u8 link_bw); + +/** + * struct drm_dp_vsc_sdp - drm DP VSC SDP + * + * This structure represents a DP VSC SDP of drm + * It is based on DP 1.4 spec [Table 2-116: VSC SDP Header Bytes] and + * [Table 2-117: VSC SDP Payload for DB16 through DB18] + * + * @sdp_type: secondary-data packet type + * @revision: revision number + * @length: number of valid data bytes + * @pixelformat: pixel encoding format + * @colorimetry: colorimetry format + * @bpc: bit per color + * @dynamic_range: dynamic range information + * @content_type: CTA-861-G defines content types and expected processing by a sink device + */ +struct drm_dp_vsc_sdp { + unsigned char sdp_type; + unsigned char revision; + unsigned char length; + enum dp_pixelformat pixelformat; + enum dp_colorimetry colorimetry; + int bpc; + enum dp_dynamic_range dynamic_range; + enum dp_content_type content_type; +}; + +void drm_dp_vsc_sdp_log(const char *level, struct device *dev, + const struct drm_dp_vsc_sdp *vsc); + +int drm_dp_psr_setup_time(const u8 psr_cap[EDP_PSR_RECEIVER_CAP_SIZE]); + +static inline int +drm_dp_max_link_rate(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return drm_dp_bw_code_to_link_rate(dpcd[DP_MAX_LINK_RATE]); +} + +static inline u8 +drm_dp_max_lane_count(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_MAX_LANE_COUNT] & DP_MAX_LANE_COUNT_MASK; +} + +static inline bool +drm_dp_enhanced_frame_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_DPCD_REV] >= 0x11 && + (dpcd[DP_MAX_LANE_COUNT] & DP_ENHANCED_FRAME_CAP); +} + +static inline bool +drm_dp_fast_training_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_DPCD_REV] >= 0x11 && + (dpcd[DP_MAX_DOWNSPREAD] & DP_NO_AUX_HANDSHAKE_LINK_TRAINING); +} + +static inline bool +drm_dp_tps3_supported(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_DPCD_REV] >= 0x12 && + dpcd[DP_MAX_LANE_COUNT] & DP_TPS3_SUPPORTED; +} + +static inline bool +drm_dp_max_downspread(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_DPCD_REV] >= 0x11 || + dpcd[DP_MAX_DOWNSPREAD] & DP_MAX_DOWNSPREAD_0_5; +} + +static inline bool +drm_dp_tps4_supported(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_DPCD_REV] >= 0x14 && + dpcd[DP_MAX_DOWNSPREAD] & DP_TPS4_SUPPORTED; +} + +static inline u8 +drm_dp_training_pattern_mask(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return (dpcd[DP_DPCD_REV] >= 0x14) ? DP_TRAINING_PATTERN_MASK_1_4 : + DP_TRAINING_PATTERN_MASK; +} + +static inline bool +drm_dp_is_branch(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_DOWNSTREAMPORT_PRESENT] & DP_DWN_STRM_PORT_PRESENT; +} + +/* DP/eDP DSC support */ +u8 drm_dp_dsc_sink_max_slice_count(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE], + bool is_edp); +u8 drm_dp_dsc_sink_line_buf_depth(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]); +int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpc[DP_DSC_RECEIVER_CAP_SIZE], + u8 dsc_bpc[3]); + +static inline bool +drm_dp_sink_supports_dsc(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]) +{ + return dsc_dpcd[DP_DSC_SUPPORT - DP_DSC_SUPPORT] & + DP_DSC_DECOMPRESSION_IS_SUPPORTED; +} + +static inline u16 +drm_edp_dsc_sink_output_bpp(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]) +{ + return dsc_dpcd[DP_DSC_MAX_BITS_PER_PIXEL_LOW - DP_DSC_SUPPORT] | + (dsc_dpcd[DP_DSC_MAX_BITS_PER_PIXEL_HI - DP_DSC_SUPPORT] & + DP_DSC_MAX_BITS_PER_PIXEL_HI_MASK << + DP_DSC_MAX_BITS_PER_PIXEL_HI_SHIFT); +} + +static inline u32 +drm_dp_dsc_sink_max_slice_width(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_SIZE]) +{ + /* Max Slicewidth = Number of Pixels * 320 */ + return dsc_dpcd[DP_DSC_MAX_SLICE_WIDTH - DP_DSC_SUPPORT] * + DP_DSC_SLICE_WIDTH_MULTIPLIER; +} + +/* Forward Error Correction Support on DP 1.4 */ +static inline bool +drm_dp_sink_supports_fec(const u8 fec_capable) +{ + return fec_capable & DP_FEC_CAPABLE; +} + +static inline bool +drm_dp_channel_coding_supported(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_MAIN_LINK_CHANNEL_CODING] & DP_CAP_ANSI_8B10B; +} + +static inline bool +drm_dp_alternate_scrambler_reset_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_EDP_CONFIGURATION_CAP] & + DP_ALTERNATE_SCRAMBLER_RESET_CAP; +} + +/* Ignore MSA timing for Adaptive Sync support on DP 1.4 */ +static inline bool +drm_dp_sink_can_do_video_without_timing_msa(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) +{ + return dpcd[DP_DOWN_STREAM_PORT_COUNT] & + DP_MSA_TIMING_PAR_IGNORED; +} + +/** + * drm_edp_backlight_supported() - Check an eDP DPCD for VESA backlight support + * @edp_dpcd: The DPCD to check + * + * Note that currently this function will return %false for panels which support various DPCD + * backlight features but which require the brightness be set through PWM, and don't support setting + * the brightness level via the DPCD. + * + * Returns: %True if @edp_dpcd indicates that VESA backlight controls are supported, %false + * otherwise + */ +static inline bool +drm_edp_backlight_supported(const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE]) +{ + return !!(edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP); +} + +/* + * DisplayPort AUX channel + */ + +/** + * struct drm_dp_aux_msg - DisplayPort AUX channel transaction + * @address: address of the (first) register to access + * @request: contains the type of transaction (see DP_AUX_* macros) + * @reply: upon completion, contains the reply type of the transaction + * @buffer: pointer to a transmission or reception buffer + * @size: size of @buffer + */ +struct drm_dp_aux_msg { + unsigned int address; + u8 request; + u8 reply; + void *buffer; + size_t size; +}; + +struct cec_adapter; +struct edid; +struct drm_connector; + +/** + * struct drm_dp_aux_cec - DisplayPort CEC-Tunneling-over-AUX + * @lock: mutex protecting this struct + * @adap: the CEC adapter for CEC-Tunneling-over-AUX support. + * @connector: the connector this CEC adapter is associated with + * @unregister_work: unregister the CEC adapter + */ +struct drm_dp_aux_cec { + struct mutex lock; + struct cec_adapter *adap; + struct drm_connector *connector; + struct delayed_work unregister_work; +}; + +/** + * struct drm_dp_aux - DisplayPort AUX channel + * + * An AUX channel can also be used to transport I2C messages to a sink. A + * typical application of that is to access an EDID that's present in the sink + * device. The @transfer() function can also be used to execute such + * transactions. The drm_dp_aux_register() function registers an I2C adapter + * that can be passed to drm_probe_ddc(). Upon removal, drivers should call + * drm_dp_aux_unregister() to remove the I2C adapter. The I2C adapter uses long + * transfers by default; if a partial response is received, the adapter will + * drop down to the size given by the partial response for this transaction + * only. + */ +struct drm_dp_aux { + /** + * @name: user-visible name of this AUX channel and the + * I2C-over-AUX adapter. + * + * It's also used to specify the name of the I2C adapter. If set + * to %NULL, dev_name() of @dev will be used. + */ + const char *name; + + /** + * @ddc: I2C adapter that can be used for I2C-over-AUX + * communication + */ + struct i2c_adapter ddc; + + /** + * @dev: pointer to struct device that is the parent for this + * AUX channel. + */ + struct device *dev; + + /** + * @drm_dev: pointer to the &drm_device that owns this AUX channel. + * Beware, this may be %NULL before drm_dp_aux_register() has been + * called. + * + * It should be set to the &drm_device that will be using this AUX + * channel as early as possible. For many graphics drivers this should + * happen before drm_dp_aux_init(), however it's perfectly fine to set + * this field later so long as it's assigned before calling + * drm_dp_aux_register(). + */ + struct drm_device *drm_dev; + + /** + * @crtc: backpointer to the crtc that is currently using this + * AUX channel + */ + struct drm_crtc *crtc; + + /** + * @hw_mutex: internal mutex used for locking transfers. + * + * Note that if the underlying hardware is shared among multiple + * channels, the driver needs to do additional locking to + * prevent concurrent access. + */ + struct mutex hw_mutex; + + /** + * @crc_work: worker that captures CRCs for each frame + */ + struct work_struct crc_work; + + /** + * @crc_count: counter of captured frame CRCs + */ + u8 crc_count; + + /** + * @transfer: transfers a message representing a single AUX + * transaction. + * + * This is a hardware-specific implementation of how + * transactions are executed that the drivers must provide. + * + * A pointer to a &drm_dp_aux_msg structure describing the + * transaction is passed into this function. Upon success, the + * implementation should return the number of payload bytes that + * were transferred, or a negative error-code on failure. + * + * Helpers will propagate these errors, with the exception of + * the %-EBUSY error, which causes a transaction to be retried. + * On a short, helpers will return %-EPROTO to make it simpler + * to check for failure. + * + * The @transfer() function must only modify the reply field of + * the &drm_dp_aux_msg structure. The retry logic and i2c + * helpers assume this is the case. + * + * Also note that this callback can be called no matter the + * state @dev is in. Drivers that need that device to be powered + * to perform this operation will first need to make sure it's + * been properly enabled. + */ + ssize_t (*transfer)(struct drm_dp_aux *aux, + struct drm_dp_aux_msg *msg); + + /** + * @i2c_nack_count: Counts I2C NACKs, used for DP validation. + */ + unsigned i2c_nack_count; + /** + * @i2c_defer_count: Counts I2C DEFERs, used for DP validation. + */ + unsigned i2c_defer_count; + /** + * @cec: struct containing fields used for CEC-Tunneling-over-AUX. + */ + struct drm_dp_aux_cec cec; + /** + * @is_remote: Is this AUX CH actually using sideband messaging. + */ + bool is_remote; +}; + +int drm_dp_dpcd_probe(struct drm_dp_aux *aux, unsigned int offset); +ssize_t drm_dp_dpcd_read(struct drm_dp_aux *aux, unsigned int offset, + void *buffer, size_t size); +ssize_t drm_dp_dpcd_write(struct drm_dp_aux *aux, unsigned int offset, + void *buffer, size_t size); + +/** + * drm_dp_dpcd_readb() - read a single byte from the DPCD + * @aux: DisplayPort AUX channel + * @offset: address of the register to read + * @valuep: location where the value of the register will be stored + * + * Returns the number of bytes transferred (1) on success, or a negative + * error code on failure. + */ +static inline ssize_t drm_dp_dpcd_readb(struct drm_dp_aux *aux, + unsigned int offset, u8 *valuep) +{ + return drm_dp_dpcd_read(aux, offset, valuep, 1); +} + +/** + * drm_dp_dpcd_writeb() - write a single byte to the DPCD + * @aux: DisplayPort AUX channel + * @offset: address of the register to write + * @value: value to write to the register + * + * Returns the number of bytes transferred (1) on success, or a negative + * error code on failure. + */ +static inline ssize_t drm_dp_dpcd_writeb(struct drm_dp_aux *aux, + unsigned int offset, u8 value) +{ + return drm_dp_dpcd_write(aux, offset, &value, 1); +} + +int drm_dp_read_dpcd_caps(struct drm_dp_aux *aux, + u8 dpcd[DP_RECEIVER_CAP_SIZE]); + +int drm_dp_dpcd_read_link_status(struct drm_dp_aux *aux, + u8 status[DP_LINK_STATUS_SIZE]); + +int drm_dp_dpcd_read_phy_link_status(struct drm_dp_aux *aux, + enum drm_dp_phy dp_phy, + u8 link_status[DP_LINK_STATUS_SIZE]); + +bool drm_dp_send_real_edid_checksum(struct drm_dp_aux *aux, + u8 real_edid_checksum); + +int drm_dp_read_downstream_info(struct drm_dp_aux *aux, + const u8 dpcd[DP_RECEIVER_CAP_SIZE], + u8 downstream_ports[DP_MAX_DOWNSTREAM_PORTS]); +bool drm_dp_downstream_is_type(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4], u8 type); +bool drm_dp_downstream_is_tmds(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4], + const struct edid *edid); +int drm_dp_downstream_max_dotclock(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4]); +int drm_dp_downstream_max_tmds_clock(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4], + const struct edid *edid); +int drm_dp_downstream_min_tmds_clock(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4], + const struct edid *edid); +int drm_dp_downstream_max_bpc(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4], + const struct edid *edid); +bool drm_dp_downstream_420_passthrough(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4]); +bool drm_dp_downstream_444_to_420_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4]); +struct drm_display_mode *drm_dp_downstream_mode(struct drm_device *dev, + const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4]); +int drm_dp_downstream_id(struct drm_dp_aux *aux, char id[6]); +void drm_dp_downstream_debug(struct seq_file *m, + const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4], + const struct edid *edid, + struct drm_dp_aux *aux); +enum drm_mode_subconnector +drm_dp_subconnector_type(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4]); +void drm_dp_set_subconnector_property(struct drm_connector *connector, + enum drm_connector_status status, + const u8 *dpcd, + const u8 port_cap[4]); + +struct drm_dp_desc; +bool drm_dp_read_sink_count_cap(struct drm_connector *connector, + const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const struct drm_dp_desc *desc); +int drm_dp_read_sink_count(struct drm_dp_aux *aux); + +int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux, + const u8 dpcd[DP_RECEIVER_CAP_SIZE], + u8 caps[DP_LTTPR_COMMON_CAP_SIZE]); +int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux, + const u8 dpcd[DP_RECEIVER_CAP_SIZE], + enum drm_dp_phy dp_phy, + u8 caps[DP_LTTPR_PHY_CAP_SIZE]); +int drm_dp_lttpr_count(const u8 cap[DP_LTTPR_COMMON_CAP_SIZE]); +int drm_dp_lttpr_max_link_rate(const u8 caps[DP_LTTPR_COMMON_CAP_SIZE]); +int drm_dp_lttpr_max_lane_count(const u8 caps[DP_LTTPR_COMMON_CAP_SIZE]); +bool drm_dp_lttpr_voltage_swing_level_3_supported(const u8 caps[DP_LTTPR_PHY_CAP_SIZE]); +bool drm_dp_lttpr_pre_emphasis_level_3_supported(const u8 caps[DP_LTTPR_PHY_CAP_SIZE]); + +void drm_dp_remote_aux_init(struct drm_dp_aux *aux); +void drm_dp_aux_init(struct drm_dp_aux *aux); +int drm_dp_aux_register(struct drm_dp_aux *aux); +void drm_dp_aux_unregister(struct drm_dp_aux *aux); + +int drm_dp_start_crc(struct drm_dp_aux *aux, struct drm_crtc *crtc); +int drm_dp_stop_crc(struct drm_dp_aux *aux); + +struct drm_dp_dpcd_ident { + u8 oui[3]; + u8 device_id[6]; + u8 hw_rev; + u8 sw_major_rev; + u8 sw_minor_rev; +} __packed; + +/** + * struct drm_dp_desc - DP branch/sink device descriptor + * @ident: DP device identification from DPCD 0x400 (sink) or 0x500 (branch). + * @quirks: Quirks; use drm_dp_has_quirk() to query for the quirks. + */ +struct drm_dp_desc { + struct drm_dp_dpcd_ident ident; + u32 quirks; +}; + +int drm_dp_read_desc(struct drm_dp_aux *aux, struct drm_dp_desc *desc, + bool is_branch); + +/** + * enum drm_dp_quirk - Display Port sink/branch device specific quirks + * + * Display Port sink and branch devices in the wild have a variety of bugs, try + * to collect them here. The quirks are shared, but it's up to the drivers to + * implement workarounds for them. + */ +enum drm_dp_quirk { + /** + * @DP_DPCD_QUIRK_CONSTANT_N: + * + * The device requires main link attributes Mvid and Nvid to be limited + * to 16 bits. So will give a constant value (0x8000) for compatability. + */ + DP_DPCD_QUIRK_CONSTANT_N, + /** + * @DP_DPCD_QUIRK_NO_PSR: + * + * The device does not support PSR even if reports that it supports or + * driver still need to implement proper handling for such device. + */ + DP_DPCD_QUIRK_NO_PSR, + /** + * @DP_DPCD_QUIRK_NO_SINK_COUNT: + * + * The device does not set SINK_COUNT to a non-zero value. + * The driver should ignore SINK_COUNT during detection. Note that + * drm_dp_read_sink_count_cap() automatically checks for this quirk. + */ + DP_DPCD_QUIRK_NO_SINK_COUNT, + /** + * @DP_DPCD_QUIRK_DSC_WITHOUT_VIRTUAL_DPCD: + * + * The device supports MST DSC despite not supporting Virtual DPCD. + * The DSC caps can be read from the physical aux instead. + */ + DP_DPCD_QUIRK_DSC_WITHOUT_VIRTUAL_DPCD, + /** + * @DP_DPCD_QUIRK_CAN_DO_MAX_LINK_RATE_3_24_GBPS: + * + * The device supports a link rate of 3.24 Gbps (multiplier 0xc) despite + * the DP_MAX_LINK_RATE register reporting a lower max multiplier. + */ + DP_DPCD_QUIRK_CAN_DO_MAX_LINK_RATE_3_24_GBPS, +}; + +/** + * drm_dp_has_quirk() - does the DP device have a specific quirk + * @desc: Device descriptor filled by drm_dp_read_desc() + * @quirk: Quirk to query for + * + * Return true if DP device identified by @desc has @quirk. + */ +static inline bool +drm_dp_has_quirk(const struct drm_dp_desc *desc, enum drm_dp_quirk quirk) +{ + return desc->quirks & BIT(quirk); +} + +/** + * struct drm_edp_backlight_info - Probed eDP backlight info struct + * @pwmgen_bit_count: The pwmgen bit count + * @pwm_freq_pre_divider: The PWM frequency pre-divider value being used for this backlight, if any + * @max: The maximum backlight level that may be set + * @lsb_reg_used: Do we also write values to the DP_EDP_BACKLIGHT_BRIGHTNESS_LSB register? + * @aux_enable: Does the panel support the AUX enable cap? + * @aux_set: Does the panel support setting the brightness through AUX? + * + * This structure contains various data about an eDP backlight, which can be populated by using + * drm_edp_backlight_init(). + */ +struct drm_edp_backlight_info { + u8 pwmgen_bit_count; + u8 pwm_freq_pre_divider; + u16 max; + + bool lsb_reg_used : 1; + bool aux_enable : 1; + bool aux_set : 1; +}; + +int +drm_edp_backlight_init(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, + u16 driver_pwm_freq_hz, const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE], + u16 *current_level, u8 *current_mode); +int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, + u16 level); +int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, + u16 level); +int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl); + +#if IS_ENABLED(CONFIG_DRM_KMS_HELPER) && (IS_BUILTIN(CONFIG_BACKLIGHT_CLASS_DEVICE) || \ + (IS_MODULE(CONFIG_DRM_KMS_HELPER) && IS_MODULE(CONFIG_BACKLIGHT_CLASS_DEVICE))) + +int drm_panel_dp_aux_backlight(struct drm_panel *panel, struct drm_dp_aux *aux); + +#else + +static inline int drm_panel_dp_aux_backlight(struct drm_panel *panel, + struct drm_dp_aux *aux) +{ + return 0; +} + +#endif + +#ifdef CONFIG_DRM_DP_CEC +void drm_dp_cec_irq(struct drm_dp_aux *aux); +void drm_dp_cec_register_connector(struct drm_dp_aux *aux, + struct drm_connector *connector); +void drm_dp_cec_unregister_connector(struct drm_dp_aux *aux); +void drm_dp_cec_set_edid(struct drm_dp_aux *aux, const struct edid *edid); +void drm_dp_cec_unset_edid(struct drm_dp_aux *aux); +#else +static inline void drm_dp_cec_irq(struct drm_dp_aux *aux) +{ +} + +static inline void +drm_dp_cec_register_connector(struct drm_dp_aux *aux, + struct drm_connector *connector) +{ +} + +static inline void drm_dp_cec_unregister_connector(struct drm_dp_aux *aux) +{ +} + +static inline void drm_dp_cec_set_edid(struct drm_dp_aux *aux, + const struct edid *edid) +{ +} + +static inline void drm_dp_cec_unset_edid(struct drm_dp_aux *aux) +{ +} + +#endif + +/** + * struct drm_dp_phy_test_params - DP Phy Compliance parameters + * @link_rate: Requested Link rate from DPCD 0x219 + * @num_lanes: Number of lanes requested by sing through DPCD 0x220 + * @phy_pattern: DP Phy test pattern from DPCD 0x248 + * @hbr2_reset: DP HBR2_COMPLIANCE_SCRAMBLER_RESET from DCPD 0x24A and 0x24B + * @custom80: DP Test_80BIT_CUSTOM_PATTERN from DPCDs 0x250 through 0x259 + * @enhanced_frame_cap: flag for enhanced frame capability. + */ +struct drm_dp_phy_test_params { + int link_rate; + u8 num_lanes; + u8 phy_pattern; + u8 hbr2_reset[2]; + u8 custom80[10]; + bool enhanced_frame_cap; +}; + +int drm_dp_get_phy_test_pattern(struct drm_dp_aux *aux, + struct drm_dp_phy_test_params *data); +int drm_dp_set_phy_test_pattern(struct drm_dp_aux *aux, + struct drm_dp_phy_test_params *data, u8 dp_rev); +int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4]); +int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool enable_frl_ready_hpd); +bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux); +int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps, + u8 frl_mode); +int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask, + u8 frl_type); +int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux); +int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux); + +bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux); +int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask); +void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux, + struct drm_connector *connector); +bool drm_dp_pcon_enc_is_dsc_1_2(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); +int drm_dp_pcon_dsc_max_slices(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); +int drm_dp_pcon_dsc_max_slice_width(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); +int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]); +int drm_dp_pcon_pps_default(struct drm_dp_aux *aux); +int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128]); +int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6]); +bool drm_dp_downstream_rgb_to_ycbcr_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE], + const u8 port_cap[4], u8 color_spc); +int drm_dp_pcon_convert_rgb_to_ycbcr(struct drm_dp_aux *aux, u8 color_spc); + +#endif /* _DRM_DP_HELPER_H_ */ diff --git a/include/drm/dp/drm_dp_mst_helper.h b/include/drm/display/drm_dp_mst_helper.h index 08276eb8c187..10adec068b7f 100644 --- a/include/drm/dp/drm_dp_mst_helper.h +++ b/include/drm/display/drm_dp_mst_helper.h @@ -23,7 +23,7 @@ #define _DRM_DP_MST_HELPER_H_ #include <linux/types.h> -#include <drm/dp/drm_dp_helper.h> +#include <drm/display/drm_dp_helper.h> #include <drm/drm_atomic.h> #if IS_ENABLED(CONFIG_DRM_DEBUG_DP_MST_TOPOLOGY_REFS) diff --git a/include/drm/drm_dsc.h b/include/drm/display/drm_dsc.h index ca022e960dcc..bc90273d06a6 100644 --- a/include/drm/drm_dsc.h +++ b/include/drm/display/drm_dsc.h @@ -8,7 +8,7 @@ #ifndef DRM_DSC_H_ #define DRM_DSC_H_ -#include <drm/dp/drm_dp_helper.h> +#include <drm/display/drm_dp.h> /* VESA Display Stream Compression DSC 1.2 constants */ #define DSC_NUM_BUF_RANGES 15 @@ -602,10 +602,4 @@ struct drm_dsc_pps_infoframe { struct drm_dsc_picture_parameter_set pps_payload; } __packed; -void drm_dsc_dp_pps_header_init(struct dp_sdp_header *pps_header); -int drm_dsc_dp_rc_buffer_size(u8 rc_buffer_block_size, u8 rc_buffer_size); -void drm_dsc_pps_payload_pack(struct drm_dsc_picture_parameter_set *pps_sdp, - const struct drm_dsc_config *dsc_cfg); -int drm_dsc_compute_rc_parameters(struct drm_dsc_config *vdsc_cfg); - #endif /* _DRM_DSC_H_ */ diff --git a/include/drm/display/drm_dsc_helper.h b/include/drm/display/drm_dsc_helper.h new file mode 100644 index 000000000000..8b41edbbabab --- /dev/null +++ b/include/drm/display/drm_dsc_helper.h @@ -0,0 +1,20 @@ +/* SPDX-License-Identifier: MIT + * Copyright (C) 2018 Intel Corp. + * + * Authors: + * Manasi Navare <manasi.d.navare@intel.com> + */ + +#ifndef DRM_DSC_HELPER_H_ +#define DRM_DSC_HELPER_H_ + +#include <drm/display/drm_dsc.h> + +void drm_dsc_dp_pps_header_init(struct dp_sdp_header *pps_header); +int drm_dsc_dp_rc_buffer_size(u8 rc_buffer_block_size, u8 rc_buffer_size); +void drm_dsc_pps_payload_pack(struct drm_dsc_picture_parameter_set *pps_sdp, + const struct drm_dsc_config *dsc_cfg); +int drm_dsc_compute_rc_parameters(struct drm_dsc_config *vdsc_cfg); + +#endif /* _DRM_DSC_HELPER_H_ */ + diff --git a/include/drm/drm_hdcp.h b/include/drm/display/drm_hdcp.h index 0b1111e3228e..96a99b1377c0 100644 --- a/include/drm/drm_hdcp.h +++ b/include/drm/display/drm_hdcp.h @@ -6,8 +6,8 @@ * Sean Paul <seanpaul@chromium.org> */ -#ifndef _DRM_HDCP_H_INCLUDED_ -#define _DRM_HDCP_H_INCLUDED_ +#ifndef _DRM_HDCP_H_ +#define _DRM_HDCP_H_ #include <linux/types.h> @@ -291,16 +291,6 @@ struct hdcp_srm_header { u8 srm_gen_no; } __packed; -struct drm_device; -struct drm_connector; - -int drm_hdcp_check_ksvs_revoked(struct drm_device *dev, - u8 *ksvs, u32 ksv_count); -int drm_connector_attach_content_protection_property( - struct drm_connector *connector, bool hdcp_content_type); -void drm_hdcp_update_content_protection(struct drm_connector *connector, - u64 val); - /* Content Type classification for HDCP2.2 vs others */ #define DRM_MODE_HDCP_CONTENT_TYPE0 0 #define DRM_MODE_HDCP_CONTENT_TYPE1 1 diff --git a/include/drm/display/drm_hdcp_helper.h b/include/drm/display/drm_hdcp_helper.h new file mode 100644 index 000000000000..8aaf87bf2735 --- /dev/null +++ b/include/drm/display/drm_hdcp_helper.h @@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: MIT */ +/* + * Copyright (C) 2017 Google, Inc. + * + * Authors: + * Sean Paul <seanpaul@chromium.org> + */ + +#ifndef _DRM_HDCP_HELPER_H_INCLUDED_ +#define _DRM_HDCP_HELPER_H_INCLUDED_ + +#include <drm/display/drm_hdcp.h> + +struct drm_device; +struct drm_connector; + +int drm_hdcp_check_ksvs_revoked(struct drm_device *dev, u8 *ksvs, u32 ksv_count); +int drm_connector_attach_content_protection_property(struct drm_connector *connector, + bool hdcp_content_type); +void drm_hdcp_update_content_protection(struct drm_connector *connector, u64 val); + +#endif diff --git a/include/drm/display/drm_hdmi_helper.h b/include/drm/display/drm_hdmi_helper.h new file mode 100644 index 000000000000..76d234826e22 --- /dev/null +++ b/include/drm/display/drm_hdmi_helper.h @@ -0,0 +1,27 @@ +/* SPDX-License-Identifier: MIT */ + +#ifndef DRM_HDMI_HELPER +#define DRM_HDMI_HELPER + +#include <linux/hdmi.h> + +struct drm_connector; +struct drm_connector_state; +struct drm_display_mode; + +void +drm_hdmi_avi_infoframe_colorimetry(struct hdmi_avi_infoframe *frame, + const struct drm_connector_state *conn_state); + +void +drm_hdmi_avi_infoframe_bars(struct hdmi_avi_infoframe *frame, + const struct drm_connector_state *conn_state); + +int +drm_hdmi_infoframe_set_hdr_metadata(struct hdmi_drm_infoframe *frame, + const struct drm_connector_state *conn_state); + +void drm_hdmi_avi_infoframe_content_type(struct hdmi_avi_infoframe *frame, + const struct drm_connector_state *conn_state); + +#endif diff --git a/include/drm/drm_scdc_helper.h b/include/drm/display/drm_scdc.h index 6a483533aae4..3d58f37e8ed8 100644 --- a/include/drm/drm_scdc_helper.h +++ b/include/drm/display/drm_scdc.h @@ -21,11 +21,8 @@ * DEALINGS IN THE SOFTWARE. */ -#ifndef DRM_SCDC_HELPER_H -#define DRM_SCDC_HELPER_H - -#include <linux/i2c.h> -#include <linux/types.h> +#ifndef DRM_SCDC_H +#define DRM_SCDC_H #define SCDC_SINK_VERSION 0x01 @@ -88,49 +85,4 @@ #define SCDC_MANUFACTURER_SPECIFIC 0xde #define SCDC_MANUFACTURER_SPECIFIC_SIZE 34 -ssize_t drm_scdc_read(struct i2c_adapter *adapter, u8 offset, void *buffer, - size_t size); -ssize_t drm_scdc_write(struct i2c_adapter *adapter, u8 offset, - const void *buffer, size_t size); - -/** - * drm_scdc_readb - read a single byte from SCDC - * @adapter: I2C adapter - * @offset: offset of register to read - * @value: return location for the register value - * - * Reads a single byte from SCDC. This is a convenience wrapper around the - * drm_scdc_read() function. - * - * Returns: - * 0 on success or a negative error code on failure. - */ -static inline int drm_scdc_readb(struct i2c_adapter *adapter, u8 offset, - u8 *value) -{ - return drm_scdc_read(adapter, offset, value, sizeof(*value)); -} - -/** - * drm_scdc_writeb - write a single byte to SCDC - * @adapter: I2C adapter - * @offset: offset of register to read - * @value: return location for the register value - * - * Writes a single byte to SCDC. This is a convenience wrapper around the - * drm_scdc_write() function. - * - * Returns: - * 0 on success or a negative error code on failure. - */ -static inline int drm_scdc_writeb(struct i2c_adapter *adapter, u8 offset, - u8 value) -{ - return drm_scdc_write(adapter, offset, &value, sizeof(value)); -} - -bool drm_scdc_get_scrambling_status(struct i2c_adapter *adapter); - -bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable); -bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set); #endif diff --git a/include/drm/display/drm_scdc_helper.h b/include/drm/display/drm_scdc_helper.h new file mode 100644 index 000000000000..ded01fd948b4 --- /dev/null +++ b/include/drm/display/drm_scdc_helper.h @@ -0,0 +1,79 @@ +/* + * Copyright (c) 2015 NVIDIA Corporation. All rights reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sub license, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER + * DEALINGS IN THE SOFTWARE. + */ + +#ifndef DRM_SCDC_HELPER_H +#define DRM_SCDC_HELPER_H + +#include <linux/types.h> + +#include <drm/display/drm_scdc.h> + +struct i2c_adapter; + +ssize_t drm_scdc_read(struct i2c_adapter *adapter, u8 offset, void *buffer, + size_t size); +ssize_t drm_scdc_write(struct i2c_adapter *adapter, u8 offset, + const void *buffer, size_t size); + +/** + * drm_scdc_readb - read a single byte from SCDC + * @adapter: I2C adapter + * @offset: offset of register to read + * @value: return location for the register value + * + * Reads a single byte from SCDC. This is a convenience wrapper around the + * drm_scdc_read() function. + * + * Returns: + * 0 on success or a negative error code on failure. + */ +static inline int drm_scdc_readb(struct i2c_adapter *adapter, u8 offset, + u8 *value) +{ + return drm_scdc_read(adapter, offset, value, sizeof(*value)); +} + +/** + * drm_scdc_writeb - write a single byte to SCDC + * @adapter: I2C adapter + * @offset: offset of register to read + * @value: return location for the register value + * + * Writes a single byte to SCDC. This is a convenience wrapper around the + * drm_scdc_write() function. + * + * Returns: + * 0 on success or a negative error code on failure. + */ +static inline int drm_scdc_writeb(struct i2c_adapter *adapter, u8 offset, + u8 value) +{ + return drm_scdc_write(adapter, offset, &value, sizeof(value)); +} + +bool drm_scdc_get_scrambling_status(struct i2c_adapter *adapter); + +bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable); +bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set); + +#endif diff --git a/include/drm/drm_atomic.h b/include/drm/drm_atomic.h index 1701c2128a5c..0777725085df 100644 --- a/include/drm/drm_atomic.h +++ b/include/drm/drm_atomic.h @@ -227,6 +227,18 @@ struct drm_private_state_funcs { */ void (*atomic_destroy_state)(struct drm_private_obj *obj, struct drm_private_state *state); + + /** + * @atomic_print_state: + * + * If driver subclasses &struct drm_private_state, it should implement + * this optional hook for printing additional driver specific state. + * + * Do not call this directly, use drm_atomic_private_obj_print_state() + * instead. + */ + void (*atomic_print_state)(struct drm_printer *p, + const struct drm_private_state *state); }; /** @@ -311,14 +323,21 @@ struct drm_private_obj { /** * struct drm_private_state - base struct for driver private object state - * @state: backpointer to global drm_atomic_state * - * Currently only contains a backpointer to the overall atomic update, but in - * the future also might hold synchronization information similar to e.g. - * &drm_crtc.commit. + * Currently only contains a backpointer to the overall atomic update, + * and the relevant private object but in the future also might hold + * synchronization information similar to e.g. &drm_crtc.commit. */ struct drm_private_state { + /** + * @state: backpointer to global drm_atomic_state + */ struct drm_atomic_state *state; + + /** + * @obj: backpointer to the private object + */ + struct drm_private_obj *obj; }; struct __drm_private_objs_state { diff --git a/include/drm/drm_atomic_uapi.h b/include/drm/drm_atomic_uapi.h index 8cec52ad1277..4c6d39d7bdb2 100644 --- a/include/drm/drm_atomic_uapi.h +++ b/include/drm/drm_atomic_uapi.h @@ -49,8 +49,6 @@ drm_atomic_set_crtc_for_plane(struct drm_plane_state *plane_state, struct drm_crtc *crtc); void drm_atomic_set_fb_for_plane(struct drm_plane_state *plane_state, struct drm_framebuffer *fb); -void drm_atomic_set_fence_for_plane(struct drm_plane_state *plane_state, - struct dma_fence *fence); int __must_check drm_atomic_set_crtc_for_connector(struct drm_connector_state *conn_state, struct drm_crtc *crtc); diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h index 5166186146f4..3ac4bf87f257 100644 --- a/include/drm/drm_connector.h +++ b/include/drm/drm_connector.h @@ -1784,9 +1784,6 @@ int drm_mode_create_aspect_ratio_property(struct drm_device *dev); int drm_mode_create_hdmi_colorspace_property(struct drm_connector *connector); int drm_mode_create_dp_colorspace_property(struct drm_connector *connector); int drm_mode_create_content_type_property(struct drm_device *dev); -void drm_hdmi_avi_infoframe_content_type(struct hdmi_avi_infoframe *frame, - const struct drm_connector_state *conn_state); - int drm_mode_create_suggested_offset_properties(struct drm_device *dev); int drm_connector_set_path_property(struct drm_connector *connector, diff --git a/include/drm/drm_edid.h b/include/drm/drm_edid.h index 144c495b99c4..c3204a58fb09 100644 --- a/include/drm/drm_edid.h +++ b/include/drm/drm_edid.h @@ -372,8 +372,8 @@ struct drm_connector; struct drm_connector_state; struct drm_display_mode; -int drm_edid_to_sad(struct edid *edid, struct cea_sad **sads); -int drm_edid_to_speaker_allocation(struct edid *edid, u8 **sadb); +int drm_edid_to_sad(const struct edid *edid, struct cea_sad **sads); +int drm_edid_to_speaker_allocation(const struct edid *edid, u8 **sadb); int drm_av_sync_delay(struct drm_connector *connector, const struct drm_display_mode *mode); @@ -401,23 +401,11 @@ drm_hdmi_vendor_infoframe_from_display_mode(struct hdmi_vendor_infoframe *frame, const struct drm_display_mode *mode); void -drm_hdmi_avi_infoframe_colorimetry(struct hdmi_avi_infoframe *frame, - const struct drm_connector_state *conn_state); - -void -drm_hdmi_avi_infoframe_bars(struct hdmi_avi_infoframe *frame, - const struct drm_connector_state *conn_state); - -void drm_hdmi_avi_infoframe_quant_range(struct hdmi_avi_infoframe *frame, const struct drm_connector *connector, const struct drm_display_mode *mode, enum hdmi_quantization_range rgb_quant_range); -int -drm_hdmi_infoframe_set_hdr_metadata(struct hdmi_drm_infoframe *frame, - const struct drm_connector_state *conn_state); - /** * drm_eld_mnl - Get ELD monitor name length in bytes. * @eld: pointer to an eld memory structure with mnl set @@ -569,8 +557,8 @@ int drm_add_edid_modes(struct drm_connector *connector, struct edid *edid); int drm_add_override_edid_modes(struct drm_connector *connector); u8 drm_match_cea_mode(const struct drm_display_mode *to_match); -bool drm_detect_hdmi_monitor(struct edid *edid); -bool drm_detect_monitor_audio(struct edid *edid); +bool drm_detect_hdmi_monitor(const struct edid *edid); +bool drm_detect_monitor_audio(const struct edid *edid); enum hdmi_quantization_range drm_default_rgb_quant_range(const struct drm_display_mode *mode); int drm_add_modes_noedid(struct drm_connector *connector, @@ -578,11 +566,11 @@ int drm_add_modes_noedid(struct drm_connector *connector, void drm_set_preferred_mode(struct drm_connector *connector, int hpref, int vpref); -int drm_edid_header_is_valid(const u8 *raw_edid); +int drm_edid_header_is_valid(const void *edid); bool drm_edid_block_valid(u8 *raw_edid, int block, bool print_bad_edid, bool *edid_corrupt); bool drm_edid_is_valid(struct edid *edid); -void drm_edid_get_monitor_name(struct edid *edid, char *name, +void drm_edid_get_monitor_name(const struct edid *edid, char *name, int buflen); struct drm_display_mode *drm_mode_find_dmt(struct drm_device *dev, int hsize, int vsize, int fresh, diff --git a/include/drm/drm_fb_helper.h b/include/drm/drm_fb_helper.h index 3af4624368d8..329607ca65c0 100644 --- a/include/drm/drm_fb_helper.h +++ b/include/drm/drm_fb_helper.h @@ -229,8 +229,7 @@ void drm_fb_helper_fill_info(struct fb_info *info, struct drm_fb_helper *fb_helper, struct drm_fb_helper_surface_size *sizes); -void drm_fb_helper_deferred_io(struct fb_info *info, - struct list_head *pagelist); +void drm_fb_helper_deferred_io(struct fb_info *info, struct list_head *pagereflist); ssize_t drm_fb_helper_sys_read(struct fb_info *info, char __user *buf, size_t count, loff_t *ppos); diff --git a/include/drm/drm_file.h b/include/drm/drm_file.h index a3acb7ac3550..e0a73a1e2df7 100644 --- a/include/drm/drm_file.h +++ b/include/drm/drm_file.h @@ -248,7 +248,7 @@ struct drm_file { */ struct drm_master *master; - /** @master_lock: Serializes @master. */ + /** @master_lookup_lock: Serializes @master. */ spinlock_t master_lookup_lock; /** @pid: Process that opened this file. */ diff --git a/include/drm/drm_format_helper.h b/include/drm/drm_format_helper.h index 0b0937c0b2f6..55145eca0782 100644 --- a/include/drm/drm_format_helper.h +++ b/include/drm/drm_format_helper.h @@ -43,8 +43,7 @@ int drm_fb_blit_toio(void __iomem *dst, unsigned int dst_pitch, uint32_t dst_for const void *vmap, const struct drm_framebuffer *fb, const struct drm_rect *rect); -void drm_fb_xrgb8888_to_mono_reversed(void *dst, unsigned int dst_pitch, const void *src, - const struct drm_framebuffer *fb, - const struct drm_rect *clip); +void drm_fb_xrgb8888_to_mono(void *dst, unsigned int dst_pitch, const void *src, + const struct drm_framebuffer *fb, const struct drm_rect *clip); #endif /* __LINUX_DRM_FORMAT_HELPER_H */ diff --git a/include/drm/drm_gem.h b/include/drm/drm_gem.h index e2941cee14b6..9d7c61a122dc 100644 --- a/include/drm/drm_gem.h +++ b/include/drm/drm_gem.h @@ -407,11 +407,6 @@ int drm_gem_lock_reservations(struct drm_gem_object **objs, int count, struct ww_acquire_ctx *acquire_ctx); void drm_gem_unlock_reservations(struct drm_gem_object **objs, int count, struct ww_acquire_ctx *acquire_ctx); -int drm_gem_fence_array_add(struct xarray *fence_array, - struct dma_fence *fence); -int drm_gem_fence_array_add_implicit(struct xarray *fence_array, - struct drm_gem_object *obj, - bool write); int drm_gem_dumb_map_offset(struct drm_file *file, struct drm_device *dev, u32 handle, u64 *offset); diff --git a/include/drm/drm_managed.h b/include/drm/drm_managed.h index b45c6fbf53ac..359883942612 100644 --- a/include/drm/drm_managed.h +++ b/include/drm/drm_managed.h @@ -8,6 +8,7 @@ #include <linux/types.h> struct drm_device; +struct mutex; typedef void (*drmres_release_t)(struct drm_device *dev, void *res); @@ -104,4 +105,6 @@ char *drmm_kstrdup(struct drm_device *dev, const char *s, gfp_t gfp); void drmm_kfree(struct drm_device *dev, void *data); +int drmm_mutex_init(struct drm_device *dev, struct mutex *lock); + #endif diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h index 147e51b6d241..51e09a1a106a 100644 --- a/include/drm/drm_mipi_dsi.h +++ b/include/drm/drm_mipi_dsi.h @@ -137,6 +137,8 @@ struct mipi_dsi_host *of_find_mipi_dsi_host_by_node(struct device_node *node); #define MIPI_DSI_CLOCK_NON_CONTINUOUS BIT(10) /* transmit data in low power */ #define MIPI_DSI_MODE_LPM BIT(11) +/* transmit data ending at the same time for all lanes within one hsync */ +#define MIPI_DSI_HS_PKT_END_ALIGNED BIT(12) enum mipi_dsi_pixel_format { MIPI_DSI_FMT_RGB888, diff --git a/include/drm/drm_modes.h b/include/drm/drm_modes.h index 2fa6b2c33b3f..a80ae9639e96 100644 --- a/include/drm/drm_modes.h +++ b/include/drm/drm_modes.h @@ -492,6 +492,8 @@ void drm_mode_set_crtcinfo(struct drm_display_mode *p, int adjust_flags); void drm_mode_copy(struct drm_display_mode *dst, const struct drm_display_mode *src); +void drm_mode_init(struct drm_display_mode *dst, + const struct drm_display_mode *src); struct drm_display_mode *drm_mode_duplicate(struct drm_device *dev, const struct drm_display_mode *mode); bool drm_mode_match(const struct drm_display_mode *mode1, diff --git a/include/drm/drm_modeset_helper_vtables.h b/include/drm/drm_modeset_helper_vtables.h index fdfa9f37ce05..fafa70ac1337 100644 --- a/include/drm/drm_modeset_helper_vtables.h +++ b/include/drm/drm_modeset_helper_vtables.h @@ -1384,7 +1384,7 @@ struct drm_mode_config_helper_funcs { * starting to commit the update to the hardware. * * After the atomic update is committed to the hardware this hook needs - * to call drm_atomic_helper_commit_hw_done(). Then wait for the upate + * to call drm_atomic_helper_commit_hw_done(). Then wait for the update * to be executed by the hardware, for example using * drm_atomic_helper_wait_for_vblanks() or * drm_atomic_helper_wait_for_flip_done(), and then clean up the old diff --git a/include/drm/drm_panel.h b/include/drm/drm_panel.h index 1ba2d424a53f..d279ee455f01 100644 --- a/include/drm/drm_panel.h +++ b/include/drm/drm_panel.h @@ -179,6 +179,13 @@ struct drm_panel { * Panel entry in registry. */ struct list_head list; + + /** + * @dsc: + * + * Panel DSC pps payload to be sent + */ + struct drm_dsc_config *dsc; }; void drm_panel_init(struct drm_panel *panel, struct device *dev, diff --git a/include/drm/drm_plane.h b/include/drm/drm_plane.h index 2628c7cde2da..89ea54652e87 100644 --- a/include/drm/drm_plane.h +++ b/include/drm/drm_plane.h @@ -74,9 +74,7 @@ struct drm_plane_state { * * Optional fence to wait for before scanning out @fb. The core atomic * code will set this when userspace is using explicit fencing. Do not - * write this field directly for a driver's implicit fence, use - * drm_atomic_set_fence_for_plane() to ensure that an explicit fence is - * preserved. + * write this field directly for a driver's implicit fence. * * Drivers should store any implicit fence in this from their * &drm_plane_helper_funcs.prepare_fb callback. See drm_gem_plane_helper_prepare_fb() diff --git a/include/drm/drm_writeback.h b/include/drm/drm_writeback.h index 9697d2714d2a..17e576c80169 100644 --- a/include/drm/drm_writeback.h +++ b/include/drm/drm_writeback.h @@ -30,6 +30,8 @@ struct drm_writeback_connector { * @drm_writeback_connector control the behaviour of the @encoder * by passing the @enc_funcs parameter to drm_writeback_connector_init() * function. + * For users of drm_writeback_connector_init_with_encoder(), this field + * is not valid as the encoder is managed within their drivers. */ struct drm_encoder encoder; @@ -150,7 +152,14 @@ int drm_writeback_connector_init(struct drm_device *dev, struct drm_writeback_connector *wb_connector, const struct drm_connector_funcs *con_funcs, const struct drm_encoder_helper_funcs *enc_helper_funcs, - const u32 *formats, int n_formats); + const u32 *formats, int n_formats, + u32 possible_crtcs); + +int drm_writeback_connector_init_with_encoder(struct drm_device *dev, + struct drm_writeback_connector *wb_connector, + struct drm_encoder *enc, + const struct drm_connector_funcs *con_funcs, const u32 *formats, + int n_formats); int drm_writeback_set_fb(struct drm_connector_state *conn_state, struct drm_framebuffer *fb); diff --git a/include/drm/gpu_scheduler.h b/include/drm/gpu_scheduler.h index 944f83ef9f2e..0fca8f38bee4 100644 --- a/include/drm/gpu_scheduler.h +++ b/include/drm/gpu_scheduler.h @@ -270,6 +270,7 @@ struct drm_sched_fence *to_drm_sched_fence(struct dma_fence *f); * @sched: the scheduler instance on which this job is scheduled. * @s_fence: contains the fences for the scheduling of job. * @finish_cb: the callback for the finished fence. + * @work: Helper to reschdeule job kill to different context. * @id: a unique id assigned to each job scheduled on the scheduler. * @karma: increment on every hang caused by this job. If this exceeds the hang * limit of the scheduler then the job is marked guilty and will not diff --git a/include/drm/i915_drm.h b/include/drm/i915_drm.h index 6722005884db..7adce327c1c2 100644 --- a/include/drm/i915_drm.h +++ b/include/drm/i915_drm.h @@ -26,8 +26,7 @@ #ifndef _I915_DRM_H_ #define _I915_DRM_H_ -#include <drm/i915_pciids.h> -#include <uapi/drm/i915_drm.h> +#include <linux/types.h> /* For use by IPS driver */ unsigned long i915_read_mch_val(void); diff --git a/include/drm/i915_mei_hdcp_interface.h b/include/drm/i915_mei_hdcp_interface.h index 702f613243bb..f441cbcd95a4 100644 --- a/include/drm/i915_mei_hdcp_interface.h +++ b/include/drm/i915_mei_hdcp_interface.h @@ -11,7 +11,7 @@ #include <linux/mutex.h> #include <linux/device.h> -#include <drm/drm_hdcp.h> +#include <drm/display/drm_hdcp.h> /** * enum hdcp_port_type - HDCP port implementation type defined by ME FW diff --git a/include/drm/i915_pciids.h b/include/drm/i915_pciids.h index 533890dc9da1..283dadfbb4db 100644 --- a/include/drm/i915_pciids.h +++ b/include/drm/i915_pciids.h @@ -679,6 +679,39 @@ INTEL_VGA_DEVICE(0xA782, info), \ INTEL_VGA_DEVICE(0xA783, info), \ INTEL_VGA_DEVICE(0xA788, info), \ - INTEL_VGA_DEVICE(0xA789, info) + INTEL_VGA_DEVICE(0xA789, info), \ + INTEL_VGA_DEVICE(0xA78A, info), \ + INTEL_VGA_DEVICE(0xA78B, info) + +/* RPL-P */ +#define INTEL_RPLP_IDS(info) \ + INTEL_VGA_DEVICE(0xA720, info), \ + INTEL_VGA_DEVICE(0xA721, info), \ + INTEL_VGA_DEVICE(0xA7A0, info), \ + INTEL_VGA_DEVICE(0xA7A1, info), \ + INTEL_VGA_DEVICE(0xA7A8, info), \ + INTEL_VGA_DEVICE(0xA7A9, info) + +/* DG2 */ +#define INTEL_DG2_G10_IDS(info) \ + INTEL_VGA_DEVICE(0x5690, info), \ + INTEL_VGA_DEVICE(0x5691, info), \ + INTEL_VGA_DEVICE(0x5692, info) + +#define INTEL_DG2_G11_IDS(info) \ + INTEL_VGA_DEVICE(0x5693, info), \ + INTEL_VGA_DEVICE(0x5694, info), \ + INTEL_VGA_DEVICE(0x5695, info), \ + INTEL_VGA_DEVICE(0x56B0, info) + +#define INTEL_DG2_G12_IDS(info) \ + INTEL_VGA_DEVICE(0x5696, info), \ + INTEL_VGA_DEVICE(0x5697, info), \ + INTEL_VGA_DEVICE(0x56B2, info) + +#define INTEL_DG2_IDS(info) \ + INTEL_DG2_G10_IDS(info), \ + INTEL_DG2_G11_IDS(info), \ + INTEL_DG2_G12_IDS(info) #endif /* _I915_PCIIDS_H */ diff --git a/include/drm/ttm/ttm_bo_api.h b/include/drm/ttm/ttm_bo_api.h index 155b19ee12fb..2d524f8b0802 100644 --- a/include/drm/ttm/ttm_bo_api.h +++ b/include/drm/ttm/ttm_bo_api.h @@ -55,8 +55,6 @@ struct ttm_placement; struct ttm_place; -struct ttm_lru_bulk_move; - /** * enum ttm_bo_type * @@ -94,10 +92,8 @@ struct ttm_tt; * @ttm: TTM structure holding system pages. * @evicted: Whether the object was evicted without user-space knowing. * @deleted: True if the object is only a zombie and already deleted. - * @lru: List head for the lru list. * @ddestroy: List head for the delayed destroy list. * @swap: List head for swap LRU list. - * @moving: Fence set when BO is moving * @offset: The current GPU offset, which can have different meanings * depending on the memory type. For SYSTEM type memory, it should be 0. * @cur_placement: Hint of current placement. @@ -138,19 +134,18 @@ struct ttm_buffer_object { struct ttm_resource *resource; struct ttm_tt *ttm; bool deleted; + struct ttm_lru_bulk_move *bulk_move; /** * Members protected by the bdev::lru_lock. */ - struct list_head lru; struct list_head ddestroy; /** * Members protected by a bo reservation. */ - struct dma_fence *moving; unsigned priority; unsigned pin_count; @@ -291,30 +286,9 @@ int ttm_bo_validate(struct ttm_buffer_object *bo, */ void ttm_bo_put(struct ttm_buffer_object *bo); -/** - * ttm_bo_move_to_lru_tail - * - * @bo: The buffer object. - * @mem: Resource object. - * @bulk: optional bulk move structure to remember BO positions - * - * Move this BO to the tail of all lru lists used to lookup and reserve an - * object. This function must be called with struct ttm_global::lru_lock - * held, and is used to make a BO less likely to be considered for eviction. - */ -void ttm_bo_move_to_lru_tail(struct ttm_buffer_object *bo, - struct ttm_resource *mem, - struct ttm_lru_bulk_move *bulk); - -/** - * ttm_bo_bulk_move_lru_tail - * - * @bulk: bulk move structure - * - * Bulk move BOs to the LRU tail, only valid to use when driver makes sure that - * BO order never changes. Should be called with ttm_global::lru_lock held. - */ -void ttm_bo_bulk_move_lru_tail(struct ttm_lru_bulk_move *bulk); +void ttm_bo_move_to_lru_tail(struct ttm_buffer_object *bo); +void ttm_bo_set_bulk_move(struct ttm_buffer_object *bo, + struct ttm_lru_bulk_move *bulk); /** * ttm_bo_lock_delayed_workqueue @@ -540,34 +514,8 @@ ssize_t ttm_bo_io(struct ttm_device *bdev, struct file *filp, int ttm_bo_swapout(struct ttm_buffer_object *bo, struct ttm_operation_ctx *ctx, gfp_t gfp_flags); -/** - * ttm_bo_pin - Pin the buffer object. - * @bo: The buffer object to pin - * - * Make sure the buffer is not evicted any more during memory pressure. - */ -static inline void ttm_bo_pin(struct ttm_buffer_object *bo) -{ - dma_resv_assert_held(bo->base.resv); - WARN_ON_ONCE(!kref_read(&bo->kref)); - ++bo->pin_count; -} - -/** - * ttm_bo_unpin - Unpin the buffer object. - * @bo: The buffer object to unpin - * - * Allows the buffer object to be evicted again during memory pressure. - */ -static inline void ttm_bo_unpin(struct ttm_buffer_object *bo) -{ - dma_resv_assert_held(bo->base.resv); - WARN_ON_ONCE(!kref_read(&bo->kref)); - if (bo->pin_count) - --bo->pin_count; - else - WARN_ON_ONCE(true); -} +void ttm_bo_pin(struct ttm_buffer_object *bo); +void ttm_bo_unpin(struct ttm_buffer_object *bo); int ttm_mem_evict_first(struct ttm_device *bdev, struct ttm_resource_manager *man, diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h index 5f087575194b..897b88f0bd59 100644 --- a/include/drm/ttm/ttm_bo_driver.h +++ b/include/drm/ttm/ttm_bo_driver.h @@ -45,33 +45,6 @@ #include "ttm_tt.h" #include "ttm_pool.h" -/** - * struct ttm_lru_bulk_move_pos - * - * @first: first BO in the bulk move range - * @last: last BO in the bulk move range - * - * Positions for a lru bulk move. - */ -struct ttm_lru_bulk_move_pos { - struct ttm_buffer_object *first; - struct ttm_buffer_object *last; -}; - -/** - * struct ttm_lru_bulk_move - * - * @tt: first/last lru entry for BOs in the TT domain - * @vram: first/last lru entry for BOs in the VRAM domain - * @swap: first/last lru entry for BOs on the swap list - * - * Helper structure for bulk moves on the LRU list. - */ -struct ttm_lru_bulk_move { - struct ttm_lru_bulk_move_pos tt[TTM_MAX_BO_PRIORITY]; - struct ttm_lru_bulk_move_pos vram[TTM_MAX_BO_PRIORITY]; -}; - /* * ttm_bo.c */ @@ -182,7 +155,7 @@ static inline void ttm_bo_move_to_lru_tail_unlocked(struct ttm_buffer_object *bo) { spin_lock(&bo->bdev->lru_lock); - ttm_bo_move_to_lru_tail(bo, bo->resource, NULL); + ttm_bo_move_to_lru_tail(bo); spin_unlock(&bo->bdev->lru_lock); } @@ -272,7 +245,7 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo, struct ttm_resource *new_mem); /** - * ttm_bo_move_accel_cleanup. + * ttm_bo_move_sync_cleanup. * * @bo: A pointer to a struct ttm_buffer_object. * @new_mem: struct ttm_resource indicating where to move. @@ -280,13 +253,8 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo, * Special case of ttm_bo_move_accel_cleanup where the bo is guaranteed * by the caller to be idle. Typically used after memcpy buffer moves. */ -static inline void ttm_bo_move_sync_cleanup(struct ttm_buffer_object *bo, - struct ttm_resource *new_mem) -{ - int ret = ttm_bo_move_accel_cleanup(bo, NULL, true, false, new_mem); - - WARN_ON(ret); -} +void ttm_bo_move_sync_cleanup(struct ttm_buffer_object *bo, + struct ttm_resource *new_mem); /** * ttm_bo_pipeline_gutting. diff --git a/include/drm/ttm/ttm_device.h b/include/drm/ttm/ttm_device.h index 0a4ddec78d8f..95b3c04b1ab9 100644 --- a/include/drm/ttm/ttm_device.h +++ b/include/drm/ttm/ttm_device.h @@ -30,8 +30,6 @@ #include <drm/ttm/ttm_resource.h> #include <drm/ttm/ttm_pool.h> -#define TTM_NUM_MEM_TYPES 8 - struct ttm_device; struct ttm_placement; struct ttm_buffer_object; @@ -201,15 +199,6 @@ struct ttm_device_funcs { void *buf, int len, int write); /** - * struct ttm_bo_driver member del_from_lru_notify - * - * @bo: the buffer object deleted from lru - * - * notify driver that a BO was deleted from LRU. - */ - void (*del_from_lru_notify)(struct ttm_buffer_object *bo); - - /** * Notify the driver that we're about to release a BO * * @bo: BO that is about to be released diff --git a/include/drm/ttm/ttm_resource.h b/include/drm/ttm/ttm_resource.h index 0f1d55262c68..441653693970 100644 --- a/include/drm/ttm/ttm_resource.h +++ b/include/drm/ttm/ttm_resource.h @@ -26,14 +26,17 @@ #define _TTM_RESOURCE_H_ #include <linux/types.h> +#include <linux/list.h> #include <linux/mutex.h> #include <linux/iosys-map.h> #include <linux/dma-fence.h> + #include <drm/drm_print.h> #include <drm/ttm/ttm_caching.h> #include <drm/ttm/ttm_kmap_iter.h> #define TTM_MAX_BO_PRIORITY 4U +#define TTM_NUM_MEM_TYPES 8 struct ttm_device; struct ttm_resource_manager; @@ -178,6 +181,47 @@ struct ttm_resource { uint32_t placement; struct ttm_bus_placement bus; struct ttm_buffer_object *bo; + + /** + * @lru: Least recently used list, see &ttm_resource_manager.lru + */ + struct list_head lru; +}; + +/** + * struct ttm_resource_cursor + * + * @priority: the current priority + * + * Cursor to iterate over the resources in a manager. + */ +struct ttm_resource_cursor { + unsigned int priority; +}; + +/** + * struct ttm_lru_bulk_move_pos + * + * @first: first res in the bulk move range + * @last: last res in the bulk move range + * + * Range of resources for a lru bulk move. + */ +struct ttm_lru_bulk_move_pos { + struct ttm_resource *first; + struct ttm_resource *last; +}; + +/** + * struct ttm_lru_bulk_move + * + * @pos: first/last lru entry for resources in the each domain/priority + * + * Container for the current bulk move state. Should be used with + * ttm_lru_bulk_move_init() and ttm_bo_set_bulk_move(). + */ +struct ttm_lru_bulk_move { + struct ttm_lru_bulk_move_pos pos[TTM_NUM_MEM_TYPES][TTM_MAX_BO_PRIORITY]; }; /** @@ -266,6 +310,15 @@ ttm_resource_manager_cleanup(struct ttm_resource_manager *man) man->move = NULL; } +void ttm_lru_bulk_move_init(struct ttm_lru_bulk_move *bulk); +void ttm_lru_bulk_move_add(struct ttm_lru_bulk_move *bulk, + struct ttm_resource *res); +void ttm_lru_bulk_move_del(struct ttm_lru_bulk_move *bulk, + struct ttm_resource *res); +void ttm_lru_bulk_move_tail(struct ttm_lru_bulk_move *bulk); + +void ttm_resource_move_to_lru_tail(struct ttm_resource *res); + void ttm_resource_init(struct ttm_buffer_object *bo, const struct ttm_place *place, struct ttm_resource *res); @@ -292,6 +345,26 @@ uint64_t ttm_resource_manager_usage(struct ttm_resource_manager *man); void ttm_resource_manager_debug(struct ttm_resource_manager *man, struct drm_printer *p); +struct ttm_resource * +ttm_resource_manager_first(struct ttm_resource_manager *man, + struct ttm_resource_cursor *cursor); +struct ttm_resource * +ttm_resource_manager_next(struct ttm_resource_manager *man, + struct ttm_resource_cursor *cursor, + struct ttm_resource *res); + +/** + * ttm_resource_manager_for_each_res - iterate over all resources + * @man: the resource manager + * @cursor: struct ttm_resource_cursor for the current position + * @res: the current resource + * + * Iterate over all the evictable resources in a resource manager. + */ +#define ttm_resource_manager_for_each_res(man, cursor, res) \ + for (res = ttm_resource_manager_first(man, cursor); res; \ + res = ttm_resource_manager_next(man, cursor, res)) + struct ttm_kmap_iter * ttm_kmap_iter_iomap_init(struct ttm_kmap_iter_iomap *iter_io, struct io_mapping *iomap, @@ -308,4 +381,8 @@ ttm_kmap_iter_linear_io_init(struct ttm_kmap_iter_linear_io *iter_io, void ttm_kmap_iter_linear_io_fini(struct ttm_kmap_iter_linear_io *iter_io, struct ttm_device *bdev, struct ttm_resource *mem); + +void ttm_resource_manager_create_debugfs(struct ttm_resource_manager *man, + struct dentry * parent, + const char *name); #endif diff --git a/include/drm/ttm/ttm_tt.h b/include/drm/ttm/ttm_tt.h index f20832139815..17a0310e8aaa 100644 --- a/include/drm/ttm/ttm_tt.h +++ b/include/drm/ttm/ttm_tt.h @@ -140,6 +140,7 @@ int ttm_tt_create(struct ttm_buffer_object *bo, bool zero_alloc); * @bo: The buffer object we create the ttm for. * @page_flags: Page flags as identified by TTM_TT_FLAG_XX flags. * @caching: the desired caching state of the pages + * @extra_pages: Extra pages needed for the driver. * * Create a struct ttm_tt to back data with system memory pages. * No pages are actually allocated. @@ -147,7 +148,8 @@ int ttm_tt_create(struct ttm_buffer_object *bo, bool zero_alloc); * NULL: Out of memory. */ int ttm_tt_init(struct ttm_tt *ttm, struct ttm_buffer_object *bo, - uint32_t page_flags, enum ttm_caching caching); + uint32_t page_flags, enum ttm_caching caching, + unsigned long extra_pages); int ttm_sg_tt_init(struct ttm_tt *ttm_dma, struct ttm_buffer_object *bo, uint32_t page_flags, enum ttm_caching caching); |