diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 42 |
1 files changed, 42 insertions, 0 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index cc6035f1a2f1..f386c480e134 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -829,6 +829,15 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3 * @RX_FLAG_10MHZ: 10 MHz (half channel) was used * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used + * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU + * subframes instead of a one huge frame for performance reasons. + * All, but the last MSDU from an A-MSDU should have this flag set. E.g. + * if an A-MSDU has 3 frames, the first 2 must have the flag set, while + * the 3rd (last) one must not have this flag set. The flag is used to + * deal with retransmission/duplication recovery properly since A-MSDU + * subframes share the same sequence number. Reported subframes can be + * either regular MSDU or singly A-MSDUs. Subframes must not be + * interleaved with other frames. */ enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR = BIT(0), @@ -859,6 +868,7 @@ enum mac80211_rx_flags { RX_FLAG_STBC_MASK = BIT(26) | BIT(27), RX_FLAG_10MHZ = BIT(28), RX_FLAG_5MHZ = BIT(29), + RX_FLAG_AMSDU_MORE = BIT(30), }; #define RX_FLAG_STBC_SHIFT 26 @@ -1492,6 +1502,11 @@ struct ieee80211_tx_control { * * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames * only, to allow getting TBTT of a DTIM beacon. + * + * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA) + * for a single active channel while using channel contexts. When support + * is not enabled the default action is to disconnect when getting the + * CSA frame. */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -1522,6 +1537,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25, IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26, IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27, + IEEE80211_HW_CHANCTX_STA_CSA = 1<<28, }; /** @@ -2666,6 +2682,10 @@ enum ieee80211_roc_type { * zero using ieee80211_csa_is_complete() after the beacon has been * transmitted and then call ieee80211_csa_finish(). * + * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all + * information in bss_conf is set up and the beacon can be retrieved. A + * channel context is bound before this is called. + * @leave_ibss: Leave the IBSS again. */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -2857,6 +2877,9 @@ struct ieee80211_ops { void (*channel_switch_beacon)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_chan_def *chandef); + + int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); }; /** @@ -3920,6 +3943,25 @@ void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw, void *data); /** + * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces + * + * This function iterates over the interfaces associated with a given + * hardware that are currently active and calls the callback for them. + * This version can only be used while holding the RTNL. + * + * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags + * @iterator: the iterator function to call, cannot sleep + * @data: first argument of the iterator function + */ +void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw, + u32 iter_flags, + void (*iterator)(void *data, + u8 *mac, + struct ieee80211_vif *vif), + void *data); + +/** * ieee80211_queue_work - add work onto the mac80211 workqueue * * Drivers and mac80211 use this to add work onto the mac80211 workqueue. |