diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 195 |
1 files changed, 154 insertions, 41 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index b0787a1dea90..9fdf982d1286 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -149,6 +149,7 @@ struct ieee80211_low_level_stats { * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed. * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note * that it is only ever disabled for station mode. + * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface. */ enum ieee80211_bss_change { BSS_CHANGED_ASSOC = 1<<0, @@ -165,6 +166,7 @@ enum ieee80211_bss_change { BSS_CHANGED_IBSS = 1<<11, BSS_CHANGED_ARP_FILTER = 1<<12, BSS_CHANGED_QOS = 1<<13, + BSS_CHANGED_IDLE = 1<<14, /* when adding here, make sure to change ieee80211_reconfig */ }; @@ -223,6 +225,9 @@ enum ieee80211_bss_change { * hardware must not perform any ARP filtering. Note, that the filter will * be enabled also in promiscuous mode. * @qos: This is a QoS-enabled BSS. + * @idle: This interface is idle. There's also a global idle flag in the + * hardware config which may be more appropriate depending on what + * your driver/device needs to do. */ struct ieee80211_bss_conf { const u8 *bssid; @@ -247,6 +252,7 @@ struct ieee80211_bss_conf { u8 arp_addr_cnt; bool arp_filter_enabled; bool qos; + bool idle; }; /** @@ -315,6 +321,9 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this * frame and selects the maximum number of streams that it can use. + * + * Note: If you have to add new flags to the enumeration, then don't + * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary. */ enum mac80211_tx_control_flags { IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), @@ -344,6 +353,19 @@ enum mac80211_tx_control_flags { #define IEEE80211_TX_CTL_STBC_SHIFT 23 +/* + * This definition is used as a mask to clear all temporary flags, which are + * set by the tx handlers for each transmission attempt by the mac80211 stack. + */ +#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \ + IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \ + IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \ + IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \ + IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \ + IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_PSPOLL_RESPONSE | \ + IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \ + IEEE80211_TX_CTL_STBC) + /** * enum mac80211_rate_control_flags - per-rate flags set by the * Rate Control algorithm. @@ -559,9 +581,6 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index * @RX_FLAG_40MHZ: HT40 (40 MHz) was used * @RX_FLAG_SHORT_GI: Short guard interval was used - * @RX_FLAG_INTERNAL_CMTR: set internally after frame was reported - * on cooked monitor to avoid double-reporting it for multiple - * virtual interfaces */ enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR = 1<<0, @@ -575,7 +594,6 @@ enum mac80211_rx_flags { RX_FLAG_HT = 1<<9, RX_FLAG_40MHZ = 1<<10, RX_FLAG_SHORT_GI = 1<<11, - RX_FLAG_INTERNAL_CMTR = 1<<12, }; /** @@ -596,6 +614,7 @@ enum mac80211_rx_flags { * @rate_idx: index of data rate into band's supported rates or MCS index if * HT rates are use (RX_FLAG_HT) * @flag: %RX_FLAG_* + * @rx_flags: internal RX flags for mac80211 */ struct ieee80211_rx_status { u64 mactime; @@ -605,6 +624,7 @@ struct ieee80211_rx_status { int antenna; int rate_idx; int flag; + unsigned int rx_flags; }; /** @@ -763,6 +783,8 @@ struct ieee80211_channel_switch { * @bss_conf: BSS configuration for this interface, either our own * or the BSS we're associated to * @addr: address of this interface + * @p2p: indicates whether this AP or STA interface is a p2p + * interface, i.e. a GO or p2p-sta respectively * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *). */ @@ -770,6 +792,7 @@ struct ieee80211_vif { enum nl80211_iftype type; struct ieee80211_bss_conf bss_conf; u8 addr[ETH_ALEN]; + bool p2p; /* must be last */ u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); }; @@ -783,20 +806,6 @@ static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) } /** - * enum ieee80211_key_alg - key algorithm - * @ALG_WEP: WEP40 or WEP104 - * @ALG_TKIP: TKIP - * @ALG_CCMP: CCMP (AES) - * @ALG_AES_CMAC: AES-128-CMAC - */ -enum ieee80211_key_alg { - ALG_WEP, - ALG_TKIP, - ALG_CCMP, - ALG_AES_CMAC, -}; - -/** * enum ieee80211_key_flags - key flags * * These flags are used for communication about keys between the driver @@ -833,7 +842,7 @@ enum ieee80211_key_flags { * @hw_key_idx: To be set by the driver, this is the key index the driver * wants to be given when a frame is transmitted and needs to be * encrypted in hardware. - * @alg: The key algorithm. + * @cipher: The key's cipher suite selector. * @flags: key flags, see &enum ieee80211_key_flags. * @keyidx: the key index (0-3) * @keylen: key material length @@ -846,7 +855,7 @@ enum ieee80211_key_flags { * @iv_len: The IV length for this key type */ struct ieee80211_key_conf { - enum ieee80211_key_alg alg; + u32 cipher; u8 icv_len; u8 iv_len; u8 hw_key_idx; @@ -1032,6 +1041,13 @@ enum ieee80211_tkip_key_type { * @IEEE80211_HW_NEED_DTIM_PERIOD: * This device needs to know the DTIM period for the BSS before * associating. + * + * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports + * per-station GTKs as used by IBSS RSN or during fast transition. If + * the device doesn't support per-station GTKs, but can be asked not + * to decrypt group addressed frames, then IBSS RSN support is still + * possible but software crypto will be used. Advertise the wiphy flag + * only in that case. */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -1055,6 +1071,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18, IEEE80211_HW_CONNECTION_MONITOR = 1<<19, IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20, + IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21, }; /** @@ -1100,8 +1117,15 @@ enum ieee80211_hw_flags { * @sta_data_size: size (in bytes) of the drv_priv data area * within &struct ieee80211_sta. * - * @max_rates: maximum number of alternate rate retry stages + * @max_rates: maximum number of alternate rate retry stages the hw + * can handle. + * @max_report_rates: maximum number of alternate rate retry stages + * the hw can report back. * @max_rate_tries: maximum number of tries for each stage + * + * @napi_weight: weight used for NAPI polling. You must specify an + * appropriate value here if a napi_poll operation is provided + * by your driver. */ struct ieee80211_hw { struct ieee80211_conf conf; @@ -1113,10 +1137,12 @@ struct ieee80211_hw { int channel_change_time; int vif_data_size; int sta_data_size; + int napi_weight; u16 queues; u16 max_listen_interval; s8 max_signal; u8 max_rates; + u8 max_report_rates; u8 max_rate_tries; }; @@ -1245,8 +1271,8 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused * with hardware wakeup and sleep states. Driver is responsible for waking - * up the hardware before issueing commands to the hardware and putting it - * back to sleep at approriate times. + * up the hardware before issuing commands to the hardware and putting it + * back to sleep at appropriate times. * * When PS is enabled, hardware needs to wakeup for beacons and receive the * buffered multicast/broadcast frames after the beacon. Also it must be @@ -1267,7 +1293,7 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, * there's data traffic and still saving significantly power in idle * periods. * - * Dynamic powersave is supported by simply mac80211 enabling and disabling + * Dynamic powersave is simply supported by mac80211 enabling and disabling * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS * flag and mac80211 will handle everything automatically. Additionally, * hardware having support for the dynamic PS feature may set the @@ -1452,12 +1478,14 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, * honour this flag if possible. * * @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS - * is not set then only those addressed to this station. + * is not set then only those addressed to this station. * * @FIF_OTHER_BSS: pass frames destined to other BSSes * - * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only - * those addressed to this station. + * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only + * those addressed to this station. + * + * @FIF_PROBE_REQ: pass probe request frames */ enum ieee80211_filter_flags { FIF_PROMISC_IN_BSS = 1<<0, @@ -1468,6 +1496,7 @@ enum ieee80211_filter_flags { FIF_CONTROL = 1<<5, FIF_OTHER_BSS = 1<<6, FIF_PSPOLL = 1<<7, + FIF_PROBE_REQ = 1<<8, }; /** @@ -1540,6 +1569,12 @@ enum ieee80211_ampdu_mlme_action { * negative error code (which will be seen in userspace.) * Must be implemented and can sleep. * + * @change_interface: Called when a netdevice changes type. This callback + * is optional, but only if it is supported can interface types be + * switched while the interface is UP. The callback may sleep. + * Note that while an interface is being switched, it will not be + * found by the interface iteration callbacks. + * * @remove_interface: Notifies a driver that an interface is going down. * The @stop callback is called after this if it is the last interface * and no monitor interfaces are present. @@ -1687,6 +1722,8 @@ enum ieee80211_ampdu_mlme_action { * switch operation for CSAs received from the AP may implement this * callback. They must then call ieee80211_chswitch_done() to indicate * completion of the channel switch. + * + * @napi_poll: Poll Rx queue for incoming data frames. */ struct ieee80211_ops { int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb); @@ -1694,6 +1731,9 @@ struct ieee80211_ops { void (*stop)(struct ieee80211_hw *hw); int (*add_interface)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + int (*change_interface)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + enum nl80211_iftype new_type, bool p2p); void (*remove_interface)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); int (*config)(struct ieee80211_hw *hw, u32 changed); @@ -1752,6 +1792,7 @@ struct ieee80211_ops { void (*flush)(struct ieee80211_hw *hw, bool drop); void (*channel_switch)(struct ieee80211_hw *hw, struct ieee80211_channel_switch *ch_switch); + int (*napi_poll)(struct ieee80211_hw *hw, int budget); }; /** @@ -1897,6 +1938,22 @@ void ieee80211_free_hw(struct ieee80211_hw *hw); */ void ieee80211_restart_hw(struct ieee80211_hw *hw); +/** ieee80211_napi_schedule - schedule NAPI poll + * + * Use this function to schedule NAPI polling on a device. + * + * @hw: the hardware to start polling + */ +void ieee80211_napi_schedule(struct ieee80211_hw *hw); + +/** ieee80211_napi_complete - complete NAPI polling + * + * Use this function to finish NAPI polling on a device. + * + * @hw: the hardware to stop polling + */ +void ieee80211_napi_complete(struct ieee80211_hw *hw); + /** * ieee80211_rx - receive frame * @@ -2252,7 +2309,8 @@ void ieee80211_wake_queues(struct ieee80211_hw *hw); * * When hardware scan offload is used (i.e. the hw_scan() callback is * assigned) this function needs to be called by the driver to notify - * mac80211 that the scan finished. + * mac80211 that the scan finished. This function can be called from + * any context, including hardirq context. * * @hw: the hardware that finished the scan * @aborted: set to true if scan was aborted @@ -2267,6 +2325,7 @@ void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted); * This function allows the iterator function to sleep, when the iterator * function is atomic @ieee80211_iterate_active_interfaces_atomic can * be used. + * Does not iterate over a new interface during add_interface() * * @hw: the hardware struct of which the interfaces should be iterated over * @iterator: the iterator function to call @@ -2284,6 +2343,7 @@ void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, * hardware that are currently active and calls the callback for them. * This function requires the iterator callback function to be atomic, * if that is not desired, use @ieee80211_iterate_active_interfaces instead. + * Does not iterate over a new interface during add_interface() * * @hw: the hardware struct of which the interfaces should be iterated over * @iterator: the iterator function to call, cannot sleep @@ -2385,25 +2445,28 @@ struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, const u8 *addr); /** - * ieee80211_find_sta_by_hw - find a station on hardware + * ieee80211_find_sta_by_ifaddr - find a station on hardware * * @hw: pointer as obtained from ieee80211_alloc_hw() - * @addr: station's address + * @addr: remote station's address + * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'. * * This function must be called under RCU lock and the * resulting pointer is only valid under RCU lock as well. * - * NOTE: This function should not be used! When mac80211 is converted - * internally to properly keep track of stations on multiple - * virtual interfaces, it will not always know which station to - * return here since a single address might be used by multiple - * logical stations (e.g. consider a station connecting to another - * BSSID on the same AP hardware without disconnecting first). + * NOTE: You may pass NULL for localaddr, but then you will just get + * the first STA that matches the remote address 'addr'. + * We can have multiple STA associated with multiple + * logical stations (e.g. consider a station connecting to another + * BSSID on the same AP hardware without disconnecting first). + * In this case, the result of this method with localaddr NULL + * is not reliable. * - * DO NOT USE THIS FUNCTION. + * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible. */ -struct ieee80211_sta *ieee80211_find_sta_by_hw(struct ieee80211_hw *hw, - const u8 *addr); +struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw, + const u8 *addr, + const u8 *localaddr); /** * ieee80211_sta_block_awake - block station from waking up @@ -2442,7 +2505,7 @@ void ieee80211_sta_block_awake(struct ieee80211_hw *hw, * * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTERING and + * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER and * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the * hardware is not receiving beacons with this function. */ @@ -2453,7 +2516,7 @@ void ieee80211_beacon_loss(struct ieee80211_vif *vif); * * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTERING, and + * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER, and * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver * needs to inform if the connection to the AP has been lost. * @@ -2518,6 +2581,34 @@ void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif, */ void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success); +/** + * ieee80211_request_smps - request SM PS transition + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @smps_mode: new SM PS mode + * + * This allows the driver to request an SM PS transition in managed + * mode. This is useful when the driver has more information than + * the stack about possible interference, for example by bluetooth. + */ +void ieee80211_request_smps(struct ieee80211_vif *vif, + enum ieee80211_smps_mode smps_mode); + +/** + * ieee80211_key_removed - disable hw acceleration for key + * @key_conf: The key hw acceleration should be disabled for + * + * This allows drivers to indicate that the given key has been + * removed from hardware acceleration, due to a new key that + * was added. Don't use this if the key can continue to be used + * for TX, if the key restriction is on RX only it is permitted + * to keep the key for TX only and not call this function. + * + * Due to locking constraints, it may only be called during + * @set_key. This function must be allowed to sleep, and the + * key it tries to disable may still be used until it returns. + */ +void ieee80211_key_removed(struct ieee80211_key_conf *key_conf); + /* Rate control API */ /** @@ -2681,4 +2772,26 @@ conf_is_ht(struct ieee80211_conf *conf) return conf->channel_type != NL80211_CHAN_NO_HT; } +static inline enum nl80211_iftype +ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p) +{ + if (p2p) { + switch (type) { + case NL80211_IFTYPE_STATION: + return NL80211_IFTYPE_P2P_CLIENT; + case NL80211_IFTYPE_AP: + return NL80211_IFTYPE_P2P_GO; + default: + break; + } + } + return type; +} + +static inline enum nl80211_iftype +ieee80211_vif_type_p2p(struct ieee80211_vif *vif) +{ + return ieee80211_iftype_p2p(vif->type, vif->p2p); +} + #endif /* MAC80211_H */ |