diff options
Diffstat (limited to 'sound/usb')
| -rw-r--r-- | sound/usb/Makefile | 1 | ||||
| -rw-r--r-- | sound/usb/format.c | 37 | ||||
| -rw-r--r-- | sound/usb/mixer_quirks.c | 5 | ||||
| -rw-r--r-- | sound/usb/mixer_s1810c.c | 595 | ||||
| -rw-r--r-- | sound/usb/mixer_s1810c.h | 7 | ||||
| -rw-r--r-- | sound/usb/quirks.c | 36 |
6 files changed, 681 insertions, 0 deletions
diff --git a/sound/usb/Makefile b/sound/usb/Makefile index 78edd7d2f418..56031026b113 100644 --- a/sound/usb/Makefile +++ b/sound/usb/Makefile @@ -13,6 +13,7 @@ snd-usb-audio-objs := card.o \ mixer_scarlett.o \ mixer_scarlett_gen2.o \ mixer_us16x08.o \ + mixer_s1810c.o \ pcm.o \ power.o \ proc.o \ diff --git a/sound/usb/format.c b/sound/usb/format.c index 9260136e4c9b..51e9fca1f3dc 100644 --- a/sound/usb/format.c +++ b/sound/usb/format.c @@ -226,6 +226,36 @@ static int parse_audio_format_rates_v1(struct snd_usb_audio *chip, struct audiof return 0; } + +/* + * Presonus Studio 1810c supports a limited set of sampling + * rates per altsetting but reports the full set each time. + * If we don't filter out the unsupported rates and attempt + * to configure the card, it will hang refusing to do any + * further audio I/O until a hard reset is performed. + * + * The list of supported rates per altsetting (set of available + * I/O channels) is described in the owner's manual, section 2.2. + */ +static bool s1810c_valid_sample_rate(struct audioformat *fp, + unsigned int rate) +{ + switch (fp->altsetting) { + case 1: + /* All ADAT ports available */ + return rate <= 48000; + case 2: + /* Half of ADAT ports available */ + return (rate == 88200 || rate == 96000); + case 3: + /* Analog I/O only (no S/PDIF nor ADAT) */ + return rate >= 176400; + default: + return false; + } + return false; +} + /* * Helper function to walk the array of sample rate triplets reported by * the device. The problem is that we need to parse whole array first to @@ -262,6 +292,12 @@ static int parse_uac2_sample_rate_range(struct snd_usb_audio *chip, } for (rate = min; rate <= max; rate += res) { + + /* Filter out invalid rates on Presonus Studio 1810c */ + if (chip->usb_id == USB_ID(0x0194f, 0x010c) && + !s1810c_valid_sample_rate(fp, rate)) + goto skip_rate; + if (fp->rate_table) fp->rate_table[nr_rates] = rate; if (!fp->rate_min || rate < fp->rate_min) @@ -276,6 +312,7 @@ static int parse_uac2_sample_rate_range(struct snd_usb_audio *chip, break; } +skip_rate: /* avoid endless loop */ if (res == 0) break; diff --git a/sound/usb/mixer_quirks.c b/sound/usb/mixer_quirks.c index c237e24f08d9..02b036b2aefb 100644 --- a/sound/usb/mixer_quirks.c +++ b/sound/usb/mixer_quirks.c @@ -34,6 +34,7 @@ #include "mixer_scarlett.h" #include "mixer_scarlett_gen2.h" #include "mixer_us16x08.h" +#include "mixer_s1810c.h" #include "helper.h" struct std_mono_table { @@ -2277,6 +2278,10 @@ int snd_usb_mixer_apply_create_quirk(struct usb_mixer_interface *mixer) case USB_ID(0x2a39, 0x3fd4): /* RME */ err = snd_rme_controls_create(mixer); break; + + case USB_ID(0x0194f, 0x010c): /* Presonus Studio 1810c */ + err = snd_sc1810_init_mixer(mixer); + break; } return err; diff --git a/sound/usb/mixer_s1810c.c b/sound/usb/mixer_s1810c.c new file mode 100644 index 000000000000..816879a07f82 --- /dev/null +++ b/sound/usb/mixer_s1810c.c @@ -0,0 +1,595 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Presonus Studio 1810c driver for ALSA + * Copyright (C) 2019 Nick Kossifidis <mickflemm@gmail.com> + * + * Based on reverse engineering of the communication protocol + * between the windows driver / Univeral Control (UC) program + * and the device, through usbmon. + * + * For now this bypasses the mixer, with all channels split, + * so that the software can mix with greater flexibility. + * It also adds controls for the 4 buttons on the front of + * the device. + */ + +#include <linux/usb.h> +#include <linux/usb/audio-v2.h> +#include <linux/slab.h> +#include <sound/core.h> +#include <sound/control.h> + +#include "usbaudio.h" +#include "mixer.h" +#include "mixer_quirks.h" +#include "helper.h" +#include "mixer_s1810c.h" + +#define SC1810C_CMD_REQ 160 +#define SC1810C_CMD_REQTYPE \ + (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT) +#define SC1810C_CMD_F1 0x50617269 +#define SC1810C_CMD_F2 0x14 + +/* + * DISCLAIMER: These are just guesses based on the + * dumps I got. + * + * It seems like a selects between + * device (0), mixer (0x64) and output (0x65) + * + * For mixer (0x64): + * * b selects an input channel (see below). + * * c selects an output channel pair (see below). + * * d selects left (0) or right (1) of that pair. + * * e 0-> disconnect, 0x01000000-> connect, + * 0x0109-> used for stereo-linking channels, + * e is also used for setting volume levels + * in which case b is also set so I guess + * this way it is possible to set the volume + * level from the specified input to the + * specified output. + * + * IN Channels: + * 0 - 7 Mic/Inst/Line (Analog inputs) + * 8 - 9 S/PDIF + * 10 - 17 ADAT + * 18 - 35 DAW (Inputs from the host) + * + * OUT Channels (pairs): + * 0 -> Main out + * 1 -> Line1/2 + * 2 -> Line3/4 + * 3 -> S/PDIF + * 4 -> ADAT? + * + * For device (0): + * * b and c are not used, at least not on the + * dumps I got. + * * d sets the control id to be modified + * (see below). + * * e sets the setting for that control. + * (so for the switches I was interested + * in it's 0/1) + * + * For output (0x65): + * * b is the output channel (see above). + * * c is zero. + * * e I guess the same as with mixer except 0x0109 + * which I didn't see in my dumps. + * + * The two fixed fields have the same values for + * mixer and output but a different set for device. + */ +struct s1810c_ctl_packet { + u32 a; + u32 b; + u32 fixed1; + u32 fixed2; + u32 c; + u32 d; + u32 e; +}; + +#define SC1810C_CTL_LINE_SW 0 +#define SC1810C_CTL_MUTE_SW 1 +#define SC1810C_CTL_AB_SW 3 +#define SC1810C_CTL_48V_SW 4 + +#define SC1810C_SET_STATE_REQ 161 +#define SC1810C_SET_STATE_REQTYPE SC1810C_CMD_REQTYPE +#define SC1810C_SET_STATE_F1 0x64656D73 +#define SC1810C_SET_STATE_F2 0xF4 + +#define SC1810C_GET_STATE_REQ 162 +#define SC1810C_GET_STATE_REQTYPE \ + (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN) +#define SC1810C_GET_STATE_F1 SC1810C_SET_STATE_F1 +#define SC1810C_GET_STATE_F2 SC1810C_SET_STATE_F2 + +#define SC1810C_STATE_F1_IDX 2 +#define SC1810C_STATE_F2_IDX 3 + +/* + * This packet includes mixer volumes and + * various other fields, it's an extended + * version of ctl_packet, with a and b + * being zero and different f1/f2. + */ +struct s1810c_state_packet { + u32 fields[63]; +}; + +#define SC1810C_STATE_48V_SW 58 +#define SC1810C_STATE_LINE_SW 59 +#define SC1810C_STATE_MUTE_SW 60 +#define SC1810C_STATE_AB_SW 62 + +struct s1810_mixer_state { + uint16_t seqnum; + struct mutex usb_mutex; + struct mutex data_mutex; +}; + +static int +snd_s1810c_send_ctl_packet(struct usb_device *dev, u32 a, + u32 b, u32 c, u32 d, u32 e) +{ + struct s1810c_ctl_packet pkt = { 0 }; + int ret = 0; + + pkt.fixed1 = SC1810C_CMD_F1; + pkt.fixed2 = SC1810C_CMD_F2; + + pkt.a = a; + pkt.b = b; + pkt.c = c; + pkt.d = d; + /* + * Value for settings 0/1 for this + * output channel is always 0 (probably because + * there is no ADAT output on 1810c) + */ + pkt.e = (c == 4) ? 0 : e; + + ret = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), + SC1810C_CMD_REQ, + SC1810C_CMD_REQTYPE, 0, 0, &pkt, sizeof(pkt)); + if (ret < 0) { + dev_warn(&dev->dev, "could not send ctl packet\n"); + return ret; + } + return 0; +} + +/* + * When opening Universal Control the program periodicaly + * sends and receives state packets for syncinc state between + * the device and the host. + * + * Note that if we send only the request to get data back we'll + * get an error, we need to first send an empty state packet and + * then ask to receive a filled. Their seqnumbers must also match. + */ +static int +snd_sc1810c_get_status_field(struct usb_device *dev, + u32 *field, int field_idx, uint16_t *seqnum) +{ + struct s1810c_state_packet pkt_out = { 0 }; + struct s1810c_state_packet pkt_in = { 0 }; + int ret = 0; + + pkt_out.fields[SC1810C_STATE_F1_IDX] = SC1810C_SET_STATE_F1; + pkt_out.fields[SC1810C_STATE_F2_IDX] = SC1810C_SET_STATE_F2; + ret = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), + SC1810C_SET_STATE_REQ, + SC1810C_SET_STATE_REQTYPE, + (*seqnum), 0, &pkt_out, sizeof(pkt_out)); + if (ret < 0) { + dev_warn(&dev->dev, "could not send state packet (%d)\n", ret); + return ret; + } + + ret = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), + SC1810C_GET_STATE_REQ, + SC1810C_GET_STATE_REQTYPE, + (*seqnum), 0, &pkt_in, sizeof(pkt_in)); + if (ret < 0) { + dev_warn(&dev->dev, "could not get state field %u (%d)\n", + field_idx, ret); + return ret; + } + + (*field) = pkt_in.fields[field_idx]; + (*seqnum)++; + return 0; +} + +/* + * This is what I got when bypassing the mixer with + * all channels split. I'm not 100% sure of what's going + * on, I could probably clean this up based on my observations + * but I prefer to keep the same behavior as the windows driver. + */ +static int snd_s1810c_init_mixer_maps(struct snd_usb_audio *chip) +{ + u32 a, b, c, e, n, off; + struct usb_device *dev = chip->dev; + + /* Set initial volume levels ? */ + a = 0x64; + e = 0xbc; + for (n = 0; n < 2; n++) { + off = n * 18; + for (b = off, c = 0; b < 18 + off; b++) { + /* This channel to all outputs ? */ + for (c = 0; c <= 8; c++) { + snd_s1810c_send_ctl_packet(dev, a, b, c, 0, e); + snd_s1810c_send_ctl_packet(dev, a, b, c, 1, e); + } + /* This channel to main output (again) */ + snd_s1810c_send_ctl_packet(dev, a, b, 0, 0, e); + snd_s1810c_send_ctl_packet(dev, a, b, 0, 1, e); + } + /* + * I noticed on UC that DAW channels have different + * initial volumes, so this makes sense. + */ + e = 0xb53bf0; + } + + /* Connect analog outputs ? */ + a = 0x65; + e = 0x01000000; + for (b = 1; b < 3; b++) { + snd_s1810c_send_ctl_packet(dev, a, b, 0, 0, e); + snd_s1810c_send_ctl_packet(dev, a, b, 0, 1, e); + } + snd_s1810c_send_ctl_packet(dev, a, 0, 0, 0, e); + snd_s1810c_send_ctl_packet(dev, a, 0, 0, 1, e); + + /* Set initial volume levels for S/PDIF mappings ? */ + a = 0x64; + e = 0xbc; + c = 3; + for (n = 0; n < 2; n++) { + off = n * 18; + for (b = off; b < 18 + off; b++) { + snd_s1810c_send_ctl_packet(dev, a, b, c, 0, e); + snd_s1810c_send_ctl_packet(dev, a, b, c, 1, e); + } + e = 0xb53bf0; + } + + /* Connect S/PDIF output ? */ + a = 0x65; + e = 0x01000000; + snd_s1810c_send_ctl_packet(dev, a, 3, 0, 0, e); + snd_s1810c_send_ctl_packet(dev, a, 3, 0, 1, e); + + /* Connect all outputs (again) ? */ + a = 0x65; + e = 0x01000000; + for (b = 0; b < 4; b++) { + snd_s1810c_send_ctl_packet(dev, a, b, 0, 0, e); + snd_s1810c_send_ctl_packet(dev, a, b, 0, 1, e); + } + + /* Basic routing to get sound out of the device */ + a = 0x64; + e = 0x01000000; + for (c = 0; c < 4; c++) { + for (b = 0; b < 36; b++) { + if ((c == 0 && b == 18) || /* DAW1/2 -> Main */ + (c == 1 && b == 20) || /* DAW3/4 -> Line3/4 */ + (c == 2 && b == 22) || /* DAW4/5 -> Line5/6 */ + (c == 3 && b == 24)) { /* DAW5/6 -> S/PDIF */ + /* Left */ + snd_s1810c_send_ctl_packet(dev, a, b, c, 0, e); + snd_s1810c_send_ctl_packet(dev, a, b, c, 1, 0); + b++; + /* Right */ + snd_s1810c_send_ctl_packet(dev, a, b, c, 0, 0); + snd_s1810c_send_ctl_packet(dev, a, b, c, 1, e); + } else { + /* Leave the rest disconnected */ + snd_s1810c_send_ctl_packet(dev, a, b, c, 0, 0); + snd_s1810c_send_ctl_packet(dev, a, b, c, 1, 0); + } + } + } + + /* Set initial volume levels for S/PDIF (again) ? */ + a = 0x64; + e = 0xbc; + c = 3; + for (n = 0; n < 2; n++) { + off = n * 18; + for (b = off; b < 18 + off; b++) { + snd_s1810c_send_ctl_packet(dev, a, b, c, 0, e); + snd_s1810c_send_ctl_packet(dev, a, b, c, 1, e); + } + e = 0xb53bf0; + } + + /* Connect S/PDIF outputs (again) ? */ + a = 0x65; + e = 0x01000000; + snd_s1810c_send_ctl_packet(dev, a, 3, 0, 0, e); + snd_s1810c_send_ctl_packet(dev, a, 3, 0, 1, e); + + /* Again ? */ + snd_s1810c_send_ctl_packet(dev, a, 3, 0, 0, e); + snd_s1810c_send_ctl_packet(dev, a, 3, 0, 1, e); + + return 0; +} + +/* + * Sync state with the device and retrieve the requested field, + * whose index is specified in (kctl->private_value & 0xFF), + * from the received fields array. + */ +static int +snd_s1810c_get_switch_state(struct usb_mixer_interface *mixer, + struct snd_kcontrol *kctl, u32 *state) +{ + struct snd_usb_audio *chip = mixer->chip; + struct s1810_mixer_state *private = mixer->private_data; + u32 field = 0; + u32 ctl_idx = (u32) (kctl->private_value & 0xFF); + int ret = 0; + + mutex_lock(&private->usb_mutex); + ret = snd_sc1810c_get_status_field(chip->dev, &field, + ctl_idx, &private->seqnum); + if (ret < 0) + goto unlock; + + *state = field; + unlock: + mutex_unlock(&private->usb_mutex); + return ret ? ret : 0; +} + +/* + * Send a control packet to the device for the control id + * specified in (kctl->private_value >> 8) with value + * specified in (kctl->private_value >> 16). + */ +static int +snd_s1810c_set_switch_state(struct usb_mixer_interface *mixer, + struct snd_kcontrol *kctl) +{ + struct snd_usb_audio *chip = mixer->chip; + struct s1810_mixer_state *private = mixer->private_data; + u32 pval = (u32) kctl->private_value; + u32 ctl_id = (pval >> 8) & 0xFF; + u32 ctl_val = (pval >> 16) & 0x1; + int ret = 0; + + mutex_lock(&private->usb_mutex); + ret = snd_s1810c_send_ctl_packet(chip->dev, 0, 0, 0, ctl_id, ctl_val); + mutex_unlock(&private->usb_mutex); + return ret; +} + +/* Generic get/set/init functions for switch controls */ + +static int +snd_s1810c_switch_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ctl_elem) +{ + struct usb_mixer_elem_list *list = snd_kcontrol_chip(kctl); + struct usb_mixer_interface *mixer = list->mixer; + struct s1810_mixer_state *private = mixer->private_data; + u32 pval = (u32) kctl->private_value; + u32 ctl_idx = pval & 0xFF; + u32 state = 0; + int ret = 0; + + mutex_lock(&private->data_mutex); + ret = snd_s1810c_get_switch_state(mixer, kctl, &state); + if (ret < 0) + goto unlock; + + switch (ctl_idx) { + case SC1810C_STATE_LINE_SW: + case SC1810C_STATE_AB_SW: + ctl_elem->value.enumerated.item[0] = (int)state; + break; + default: + ctl_elem->value.integer.value[0] = (long)state; + } + + unlock: + mutex_unlock(&private->data_mutex); + return (ret < 0) ? ret : 0; +} + +static int +snd_s1810c_switch_set(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ctl_elem) +{ + struct usb_mixer_elem_list *list = snd_kcontrol_chip(kctl); + struct usb_mixer_interface *mixer = list->mixer; + struct s1810_mixer_state *private = mixer->private_data; + u32 pval = (u32) kctl->private_value; + u32 ctl_idx = pval & 0xFF; + u32 curval = 0; + u32 newval = 0; + int ret = 0; + + mutex_lock(&private->data_mutex); + ret = snd_s1810c_get_switch_state(mixer, kctl, &curval); + if (ret < 0) + goto unlock; + + switch (ctl_idx) { + case SC1810C_STATE_LINE_SW: + case SC1810C_STATE_AB_SW: + newval = (u32) ctl_elem->value.enumerated.item[0]; + break; + default: + newval = (u32) ctl_elem->value.integer.value[0]; + } + + if (curval == newval) + goto unlock; + + kctl->private_value &= ~(0x1 << 16); + kctl->private_value |= (unsigned int)(newval & 0x1) << 16; + ret = snd_s1810c_set_switch_state(mixer, kctl); + + unlock: + mutex_unlock(&private->data_mutex); + return (ret < 0) ? 0 : 1; +} + +static int +snd_s1810c_switch_init(struct usb_mixer_interface *mixer, + const struct snd_kcontrol_new *new_kctl) +{ + struct snd_kcontrol *kctl; + struct usb_mixer_elem_info *elem; + + elem = kzalloc(sizeof(struct usb_mixer_elem_info), GFP_KERNEL); + if (!elem) + return -ENOMEM; + + elem->head.mixer = mixer; + elem->control = 0; + elem->head.id = 0; + elem->channels = 1; + + kctl = snd_ctl_new1(new_kctl, elem); + if (!kctl) { + kfree(elem); + return -ENOMEM; + } + kctl->private_free = snd_usb_mixer_elem_free; + + return snd_usb_mixer_add_control(&elem->head, kctl); +} + +static int +snd_s1810c_line_sw_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + static const char *const texts[2] = { + "Preamp On (Mic/Inst)", + "Preamp Off (Line in)" + }; + + return snd_ctl_enum_info(uinfo, 1, ARRAY_SIZE(texts), texts); +} + +static const struct snd_kcontrol_new snd_s1810c_line_sw = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "Line 1/2 Source Type", + .info = snd_s1810c_line_sw_info, + .get = snd_s1810c_switch_get, + .put = snd_s1810c_switch_set, + .private_value = (SC1810C_STATE_LINE_SW | SC1810C_CTL_LINE_SW << 8) +}; + +static const struct snd_kcontrol_new snd_s1810c_mute_sw = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "Mute Main Out Switch", + .info = snd_ctl_boolean_mono_info, + .get = snd_s1810c_switch_get, + .put = snd_s1810c_switch_set, + .private_value = (SC1810C_STATE_MUTE_SW | SC1810C_CTL_MUTE_SW << 8) +}; + +static const struct snd_kcontrol_new snd_s1810c_48v_sw = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "48V Phantom Power On Mic Inputs Switch", + .info = snd_ctl_boolean_mono_info, + .get = snd_s1810c_switch_get, + .put = snd_s1810c_switch_set, + .private_value = (SC1810C_STATE_48V_SW | SC1810C_CTL_48V_SW << 8) +}; + +static int +snd_s1810c_ab_sw_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + static const char *const texts[2] = { + "1/2", + "3/4" + }; + + return snd_ctl_enum_info(uinfo, 1, ARRAY_SIZE(texts), texts); +} + +static const struct snd_kcontrol_new snd_s1810c_ab_sw = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "Headphone 1 Source Route", + .info = snd_s1810c_ab_sw_info, + .get = snd_s1810c_switch_get, + .put = snd_s1810c_switch_set, + .private_value = (SC1810C_STATE_AB_SW | SC1810C_CTL_AB_SW << 8) +}; + +static void snd_sc1810_mixer_state_free(struct usb_mixer_interface *mixer) +{ + struct s1810_mixer_state *private = mixer->private_data; + kfree(private); + mixer->private_data = NULL; +} + +/* Entry point, called from mixer_quirks.c */ +int snd_sc1810_init_mixer(struct usb_mixer_interface *mixer) +{ + struct s1810_mixer_state *private = NULL; + struct snd_usb_audio *chip = mixer->chip; + struct usb_device *dev = chip->dev; + int ret = 0; + + /* Run this only once */ + if (!list_empty(&chip->mixer_list)) + return 0; + + dev_info(&dev->dev, + "Presonus Studio 1810c, device_setup: %u\n", chip->setup); + if (chip->setup == 1) + dev_info(&dev->dev, "(8out/18in @ 48KHz)\n"); + else if (chip->setup == 2) + dev_info(&dev->dev, "(6out/8in @ 192KHz)\n"); + else + dev_info(&dev->dev, "(8out/14in @ 96KHz)\n"); + + ret = snd_s1810c_init_mixer_maps(chip); + if (ret < 0) + return ret; + + private = kzalloc(sizeof(struct s1810_mixer_state), GFP_KERNEL); + if (!private) + return -ENOMEM; + + mutex_init(&private->usb_mutex); + mutex_init(&private->data_mutex); + + mixer->private_data = private; + mixer->private_free = snd_sc1810_mixer_state_free; + + private->seqnum = 1; + + ret = snd_s1810c_switch_init(mixer, &snd_s1810c_line_sw); + if (ret < 0) + return ret; + + ret = snd_s1810c_switch_init(mixer, &snd_s1810c_mute_sw); + if (ret < 0) + return ret; + + ret = snd_s1810c_switch_init(mixer, &snd_s1810c_48v_sw); + if (ret < 0) + return ret; + + ret = snd_s1810c_switch_init(mixer, &snd_s1810c_ab_sw); + if (ret < 0) + return ret; + return ret; +} diff --git a/sound/usb/mixer_s1810c.h b/sound/usb/mixer_s1810c.h new file mode 100644 index 000000000000..a79a3743cff3 --- /dev/null +++ b/sound/usb/mixer_s1810c.h @@ -0,0 +1,7 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Presonus Studio 1810c driver for ALSA + * Copyright (C) 2019 Nick Kossifidis <mickflemm@gmail.com> + */ + +int snd_sc1810_init_mixer(struct usb_mixer_interface *mixer); diff --git a/sound/usb/quirks.c b/sound/usb/quirks.c index 3a5242e383b2..58761d408759 100644 --- a/sound/usb/quirks.c +++ b/sound/usb/quirks.c @@ -1252,6 +1252,38 @@ static int fasttrackpro_skip_setting_quirk(struct snd_usb_audio *chip, return 0; /* keep this altsetting */ } +static int s1810c_skip_setting_quirk(struct snd_usb_audio *chip, + int iface, int altno) +{ + /* + * Altno settings: + * + * Playback (Interface 1): + * 1: 6 Analog + 2 S/PDIF + * 2: 6 Analog + 2 S/PDIF + * 3: 6 Analog + * + * Capture (Interface 2): + * 1: 8 Analog + 2 S/PDIF + 8 ADAT + * 2: 8 Analog + 2 S/PDIF + 4 ADAT + * 3: 8 Analog + */ + + /* + * I'll leave 2 as the default one and + * use device_setup to switch to the + * other two. + */ + if ((chip->setup == 0 || chip->setup > 2) && altno != 2) + return 1; + else if (chip->setup == 1 && altno != 1) + return 1; + else if (chip->setup == 2 && altno != 3) + return 1; + + return 0; +} + int snd_usb_apply_interface_quirk(struct snd_usb_audio *chip, int iface, int altno) @@ -1265,6 +1297,10 @@ int snd_usb_apply_interface_quirk(struct snd_usb_audio *chip, /* fasttrackpro usb: skip altsets incompatible with device_setup */ if (chip->usb_id == USB_ID(0x0763, 0x2012)) return fasttrackpro_skip_setting_quirk(chip, iface, altno); + /* presonus studio 1810c: skip altsets incompatible with device_setup */ + if (chip->usb_id == USB_ID(0x0194f, 0x010c)) + return s1810c_skip_setting_quirk(chip, iface, altno); + return 0; } |