summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* xfrm: refine validation of template and selector familiesFlorian Westphal2019-01-101-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The check assumes that in transport mode, the first templates family must match the address family of the policy selector. Syzkaller managed to build a template using MODE_ROUTEOPTIMIZATION, with ipv4-in-ipv6 chain, leading to following splat: BUG: KASAN: stack-out-of-bounds in xfrm_state_find+0x1db/0x1854 Read of size 4 at addr ffff888063e57aa0 by task a.out/2050 xfrm_state_find+0x1db/0x1854 xfrm_tmpl_resolve+0x100/0x1d0 xfrm_resolve_and_create_bundle+0x108/0x1000 [..] Problem is that addresses point into flowi4 struct, but xfrm_state_find treats them as being ipv6 because it uses templ->encap_family is used (AF_INET6 in case of reproducer) rather than family (AF_INET). This patch inverts the logic: Enforce 'template family must match selector' EXCEPT for tunnel and BEET mode. In BEET and Tunnel mode, xfrm_tmpl_resolve_one will have remote/local address pointers changed to point at the addresses found in the template, rather than the flowi ones, so no oob read will occur. Reported-by: 3ntr0py1337@gmail.com Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnelSu Yanjun2019-01-091-0/+50
| | | | | | | | | | | | | | | | | | Recently we run a network test over ipcomp virtual tunnel.We find that if a ipv4 packet needs fragment, then the peer can't receive it. We deep into the code and find that when packet need fragment the smaller fragment will be encapsulated by ipip not ipcomp. So when the ipip packet goes into xfrm, it's skb->dev is not properly set. The ipv4 reassembly code always set skb'dev to the last fragment's dev. After ipv4 defrag processing, when the kernel rp_filter parameter is set, the skb will be drop by -EXDEV error. This patch adds compatible support for the ipip process in ipcomp virtual tunnel. Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* xfrm: policy: fix infinite loop when merging src-nodesFlorian Westphal2019-01-092-10/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | With very small change to test script we can trigger softlockup due to bogus assignment of 'p' (policy to be examined) on restart. Previously the two to-be-merged nodes had same address/prefixlength pair, so no erase/reinsert was necessary, we only had to append the list from node a to b. If prefix lengths are different, the node has to be deleted and re-inserted into the tree, with the updated prefix length. This was broken; due to bogus update to 'p' this loops forever. Add a 'restart' label and use that instead. While at it, don't perform the unneeded reinserts of the policies that are already sorted into the 'new' node. A previous patch in this series made xfrm_policy_inexact_list_reinsert() use the relative position indicator to sort policies according to age in case priorities are identical. Fixes: 6ac098b2a9d30 ("xfrm: policy: add 2nd-level saddr trees for inexact policies") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* selftests: xfrm: alter htresh to trigger move of policies to hash tableFlorian Westphal2019-01-091-4/+40
| | | | | | | | ... and back to inexact tree. Repeat ping test after each htresh change: lookup results must not change. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* xfrm: policy: fix reinsertion on node mergeFlorian Westphal2019-01-091-6/+8
| | | | | | | | | | | | | | | | | | | | | | | "newpos" has wrong scope. It must be NULL on each iteration of the loop. Otherwise, when policy is to be inserted at the start, we would instead insert at point found by the previous loop-iteration instead. Also, we need to unlink the policy before we reinsert it to the new node, else we can get next-points-to-self loops. Because policies are only ordered by priority it is irrelevant which policy is "more recent" except when two policies have same priority. (the more recent one is placed after the older one). In these cases, we can use the ->pos id number to know which one is the 'older': the higher the id, the more recent the policy. So we only need to unlink all policies from the node that is about to be removed, and insert them to the replacement node. Fixes: 9cf545ebd591da ("xfrm: policy: store inexact policies in a tree ordered by destination address") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* xfrm: policy: delete inexact policies from inexact list on hash rebuildFlorian Westphal2019-01-091-13/+10
| | | | | | | | | | | | | | | | | | | | | | An xfrm hash rebuild has to reset the inexact policy list before the policies get re-inserted: A change of hash thresholds will result in policies to get moved from inexact tree to the policy hash table. If the thresholds are increased again later, they get moved from hash table to inexact tree. We must unlink all policies from the inexact tree before re-insertion. Otherwise 'migrate' may find policies that are in main hash table a second time, when it searches the inexact lists. Furthermore, re-insertion without deletion can cause elements ->next to point back to itself, causing soft lockups or double-frees. Reported-by: syzbot+9d971dd21eb26567036b@syzkaller.appspotmail.com Fixes: 9cf545ebd591da ("xfrm: policy: store inexact policies in a tree ordered by destination address") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* xfrm: policy: increment xfrm_hash_generation on hash rebuildFlorian Westphal2019-01-091-0/+2
| | | | | | | | | | | | | | | | Hash rebuild will re-set all the inexact entries, then re-insert them. Lookups that can occur in parallel will therefore not find any policies. This was safe when lookups were still guarded by rwlock. After rcu-ification, lookups check the hash_generation seqcount to detect when a hash resize takes place. Hash rebuild missed the needed increment. Hash resizes and hash rebuilds cannot occur in parallel (both acquire hash_resize_mutex), so just increment xfrm_hash_generation, like resize. Fixes: a7c44247f704e3 ("xfrm: policy: make xfrm_policy_lookup_bytype lockless") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* xfrm: policy: use hlist rcu variants on inexact insert, part 2Florian Westphal2019-01-091-2/+2
| | | | | | | | | | | | This function was modeled on the 'exact' insert one, which did not use the rcu variant either. When I fixed the 'exact' insert I forgot to propagate this to my development tree, so the inexact variant retained the bug. Fixes: 9cf545ebd591d ("xfrm: policy: store inexact policies in a tree ordered by destination address") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* selftests: xfrm: add block rules with adjacent/overlapping subnetsFlorian Westphal2019-01-091-18/+91
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The existing script lacks a policy pattern that triggers 'tree node merges' in the kernel. Consider adding policy affecting following subnet: pol1: dst 10.0.0.0/22 pol2: dst 10.0.0.0/23 # adds to existing 10.0.0.0/22 node -> no problems here. But now, lets consider reverse order: pol1: dst 10.0.0.0/24 pol2: dst 10.0.0.0/23 # CANNOT add to existing node When second policy gets added, the kernel must check that the new node ("10.0.0.0/23") doesn't overlap with any existing subnet. Example: dst 10.0.0.0/24 dst 10.0.0.1/24 dst 10.0.0.0/23 When the third policy gets added, the kernel must replace the nodes for the 10.0.0.0/24 and 10.0.0.1/24 policies with a single one and must merge all the subtrees/lists stored in those nodes into the new node. The existing test cases only have overlaps with a single node, so no merging takes place (we can always remove the 'old' node and replace it with the new subnet prefix). Add a few 'block policies' in a pattern that triggers this, with a priority that will make kernel prefer the 'esp' rules. Make sure the 'tunnel ping' tests still pass after they have been added. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* packet: Do not leak dev refcounts on error exitJason Gunthorpe2019-01-091-2/+2
| | | | | | | | | | | | | | 'dev' is non NULL when the addr_len check triggers so it must goto a label that does the dev_put otherwise dev will have a leaked refcount. This bug causes the ib_ipoib module to become unloadable when using systemd-network as it triggers this check on InfiniBand links. Fixes: 99137b7888f4 ("packet: validate address length") Reported-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'mlxsw-fixes'David S. Miller2019-01-0811-35/+74
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Daniel Borkmann says: ==================== pull-request: bpf 2019-01-08 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) Fix BSD'ism in sendmsg(2) to rewrite unspecified IPv6 dst for unconnected UDP sockets with [::1] _after_ cgroup BPF invocation, from Andrey. 2) Follow-up fix to the speculation fix where we need to reject a corner case for sanitation when ptr and scalars are mixed in the same alu op. Also, some unrelated minor doc fixes, from Daniel. 3) Fix BPF kselftest's incorrect uses of create_and_get_cgroup() by not assuming fd of zero value to be the result of an error case, from Stanislav. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * selftests: forwarding: Add a test for VLAN deletionIdo Schimmel2019-01-081-1/+14
| | | | | | | | | | | | | | | | Add a VLAN on a bridge port, delete it and make sure the PVID VLAN is not affected. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: spectrum_switchdev: Set PVID correctly during VLAN deletionIdo Schimmel2019-01-081-1/+1
| | | | | | | | | | | | | | | | | | | | When a VLAN is deleted from a bridge port we should not change the PVID unless the deleted VLAN is the PVID. Fixes: fe9ccc785de5 ("mlxsw: spectrum_switchdev: Don't batch VLAN operations") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * selftests: forwarding: Fix test for different devicesIdo Schimmel2019-01-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When running the test on the Spectrum ASIC the generated packets are counted on the ingress filter and injected back to the pipeline because of the 'pass' action. The router block then drops the packets due to checksum error, as the test generates packets with zero checksum. When running the test on an emulator that is not as strict about checksum errors the test fails since packets are counted twice. Once by the emulated ASIC on its ingress filter and again by the kernel as the emulator does not perform checksum validation and allows the packets to be trapped by a matching host route. Fix this by changing the action to 'drop', which will prevent the packet from continuing further in the pipeline to the router block. For veth pairs this change is essentially a NOP given packets are only processed once (by the kernel). Fixes: a0b61f3d8ebf ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: bridge: Fix VLANs memory leakIdo Schimmel2019-01-082-13/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When adding / deleting VLANs to / from a bridge port, the bridge driver first tries to propagate the information via switchdev and falls back to the 8021q driver in case the underlying driver does not support switchdev. This can result in a memory leak [1] when VXLAN and mlxsw ports are enslaved to the bridge: $ ip link set dev vxlan0 master br0 # No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev # notification and the bridge driver adds the VLAN on 'vxlan0' via the # 8021q driver $ bridge vlan add vid 10 dev vxlan0 pvid untagged # mlxsw port is enslaved to the bridge $ ip link set dev swp1 master br0 # mlxsw processes the switchdev notification and the 8021q driver is # skipped $ bridge vlan del vid 10 dev vxlan0 This results in 'struct vlan_info' and 'struct vlan_vid_info' being leaked, as they were allocated by the 8021q driver during VLAN addition, but never freed as the 8021q driver was skipped during deletion. Fix this by introducing a new VLAN private flag that indicates whether the VLAN was added on the port by switchdev or the 8021q driver. If the VLAN was added by the 8021q driver, then we make sure to delete it via the 8021q driver as well. [1] unreferenced object 0xffff88822d20b1e8 (size 256): comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s) hex dump (first 32 bytes): e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00 .B.............. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330 [<00000000e0178b02>] vlan_vid_add+0x661/0x920 [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00 [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90 [<000000003535392c>] br_vlan_info+0x132/0x410 [<00000000aedaa9dc>] br_afspec+0x75c/0x870 [<00000000f5716133>] br_setlink+0x3dc/0x6d0 [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30 [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80 [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0 [<000000008be8d614>] rtnetlink_rcv+0x21/0x30 [<000000009ab2ca25>] netlink_unicast+0x52f/0x740 [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50 [<000000005d1e2050>] sock_sendmsg+0xbe/0x120 [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0 [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270 unreferenced object 0xffff888227454308 (size 32): comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s) hex dump (first 32 bytes): 88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff .. -...... -.... 81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330 [<0000000018050631>] vlan_vid_add+0x3e6/0x920 [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00 [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90 [<000000003535392c>] br_vlan_info+0x132/0x410 [<00000000aedaa9dc>] br_afspec+0x75c/0x870 [<00000000f5716133>] br_setlink+0x3dc/0x6d0 [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30 [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80 [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0 [<000000008be8d614>] rtnetlink_rcv+0x21/0x30 [<000000009ab2ca25>] netlink_unicast+0x52f/0x740 [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50 [<000000005d1e2050>] sock_sendmsg+0xbe/0x120 [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0 [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270 Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: bridge@lists.linux-foundation.org Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * selftests: mlxsw: Add a test case for VLAN addition error flowIdo Schimmel2019-01-081-0/+18
| | | | | | | | | | | | | | | | | | | | Add a test case for the issue fixed by previous commit. In case the offloading of an unsupported VxLAN tunnel was triggered by adding the mapped VLAN to a local port, then error should be returned to the user. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: spectrum_nve: Replace error code with EINVALIdo Schimmel2019-01-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adding a VLAN on a port can trigger the offload of a VXLAN tunnel which is already a member in the VLAN. In case the configuration of the VXLAN is not supported, the driver would return -EOPNOTSUPP. This is problematic since bridge code does not interpret this as error, but rather that it should try to setup the VLAN using the 8021q driver instead of switchdev. Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: spectrum_switchdev: Avoid returning errors in commit phaseIdo Schimmel2019-01-081-12/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Drivers are not supposed to return errors in switchdev commit phase if they returned OK in prepare phase. Otherwise, a WARNING is emitted. However, when the offloading of a VXLAN tunnel is triggered by the addition of a VLAN on a local port, it is not possible to guarantee that the commit phase will succeed without doing a lot of work. In these cases, the artificial division between prepare and commit phase does not make sense, so simply do the work in the prepare phase. Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: spectrum: Add VXLAN dependency for spectrumIdo Schimmel2019-01-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When VXLAN is a loadable module, MLXSW_SPECTRUM must not be built-in: drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:2547: undefined reference to `vxlan_fdb_find_uc' Add Kconfig dependency to enforce usable configurations. Fixes: 1231e04f5bba ("mlxsw: spectrum_switchdev: Add support for VxLAN encapsulation") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: kbuild test robot <lkp@intel.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: spectrum: Disable lag port TX before removing itJiri Pirko2019-01-081-2/+5
| | | | | | | | | | | | | | | | | | | | Make sure that lag port TX is disabled before mlxsw_sp_port_lag_leave() is called and prevent from possible EMAD error. Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: spectrum_acl: Remove ASSERT_RTNL()s in module removal flowNir Dotan2019-01-081-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removal of the mlxsw driver on Spectrum-2 platforms hits an ASSERT_RTNL() in Spectrum-2 ACL Bloom filter and in ERP removal paths. This happens because the multicast router implementation in Spectrum-2 relies on ACLs. Taking the RTNL lock upon driver removal is useless since the driver first removes its ports and unregisters from notifiers so concurrent writes cannot happen at that time. The assertions were originally put as a reminder for future work involving ERP background optimization, but having these assertions only during addition serves this purpose as well. Therefore remove the ASSERT_RTNL() in both places related to ERP and Bloom filter removal. Fixes: cf7221a4f5a5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2") Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: spectrum_acl: Add cleanup after C-TCAM update error conditionNir Dotan2019-01-081-1/+9
|/ | | | | | | | | | | | | | When writing to C-TCAM, mlxsw driver uses cregion->ops->entry_insert(). In case of C-TCAM HW insertion error, the opposite action should take place. Add error handling case in which the C-TCAM region entry is removed, by calling cregion->ops->entry_remove(). Fixes: a0a777b9409f ("mlxsw: spectrum_acl: Start using A-TCAM") Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* r8169: load Realtek PHY driver module before r8169Heiner Kallweit2019-01-081-0/+1
| | | | | | | | | | | | | | | | | This soft dependency works around an issue where sometimes the genphy driver is used instead of the dedicated PHY driver. The root cause of the issue isn't clear yet. People reported the unloading/re-loading module r8169 helps, and also configuring this soft dependency in the modprobe config files. Important just seems to be that the realtek module is loaded before r8169. Once this has been applied preliminary fix 38af4b903210 ("net: phy: add workaround for issue where PHY driver doesn't bind to the device") will be removed. Fixes: f1e911d5d0df ("r8169: add basic phylib support") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* lan743x: Remove phy_read from link status change functionBryan Whitehead2019-01-081-7/+4
| | | | | | | | | | | | | It has been noticed that some phys do not have the registers required by the previous implementation. To fix this, instead of using phy_read, the required information is extracted from the phy_device structure. fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* ptp: uapi: change _IOW to IOWR in PTP_SYS_OFFSET_EXTENDED definitionEugene Syromiatnikov2019-01-081-1/+1
| | | | | | | | The ioctl command is read/write (or just read, if the fact that user space writes n_samples field is ignored). Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ptp: check that rsv field is zero in struct ptp_sys_offset_extendedEugene Syromiatnikov2019-01-081-1/+2
| | | | | | | | | | | Otherwise it is impossible to use it for something else, as it will break userspace that puts garbage there. The same check should be done in other structures, but the fact that data in reserved fields is ignored is already part of the kernel ABI. Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge ra.kernel.org:/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller2019-01-0818-46/+262
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Daniel Borkmann says: ==================== pull-request: bpf 2019-01-08 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) Fix BSD'ism in sendmsg(2) to rewrite unspecified IPv6 dst for unconnected UDP sockets with [::1] _after_ cgroup BPF invocation, from Andrey. 2) Follow-up fix to the speculation fix where we need to reject a corner case for sanitation when ptr and scalars are mixed in the same alu op. Also, some unrelated minor doc fixes, from Daniel. 3) Fix BPF kselftest's incorrect uses of create_and_get_cgroup() by not assuming fd of zero value to be the result of an error case, from Stanislav. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge branch 'bpf-doc-updates'Alexei Starovoitov2019-01-082-6/+19
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Daniel Borkmann says: ==================== Two trivial doc follow-ups to i) remove deprecated kern_version mentioning in the design qa and ii) to mention stand-alone build and license of libbpf. Thanks! ==================== Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| | * bpf, doc: add note for libbpf's stand-alone buildDaniel Borkmann2019-01-081-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Given this came up couple of times, add a note to libbpf's readme about the semi-automated mirror for a stand-alone build which is officially managed by BPF folks. While at it, also explicitly state the libbpf license in the readme file. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| | * bpf, doc: update design qa to reflect kern_version requirementDaniel Borkmann2019-01-081-6/+5
| |/ | | | | | | | | | | | | | | | | | | Update the bpf_design_QA.rst to also reflect recent changes in 6c4fc209fcf9 ("bpf: remove useless version check for prog load"). Suggested-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| * selftests/bpf: fix incorrect users of create_and_get_cgroupStanislav Fomichev2019-01-0712-20/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have some tests that assume create_and_get_cgroup returns -1 on error which is incorrect (it returns 0 on error). Since fd might be zero in general case, change create_and_get_cgroup to return -1 on error and fix the users that assume 0 on error. Fixes: f269099a7e7a ("tools/bpf: add a selftest for bpf_get_current_cgroup_id() helper") Fixes: 7d2c6cfc5411 ("bpf: use --cgroup in test_suite if supplied") v2: - instead of fixing the uses that assume -1 on error, convert the users that assume 0 on error (fd might be zero in general case) Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| * Merge branch 'reject-ptr-scalar-mix'Alexei Starovoitov2019-01-063-13/+169
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Daniel Borkmann says: ==================== Follow-up fix to 979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic") in order to reject a corner case for sanitation when ptr / scalars are mixed in the same alu op. ==================== Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| | * bpf: add various test cases for alu op on mixed dst register typesDaniel Borkmann2019-01-061-0/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add couple of test_verifier tests to check sanitation of alu op insn with pointer and scalar type coming from different paths. This also includes BPF insns of the test reproducer provided by Jann Horn. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| | * bpf: fix sanitation of alu op with pointer / scalar type from different pathsDaniel Borkmann2019-01-062-13/+49
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While 979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic") took care of rejecting alu op on pointer when e.g. pointer came from two different map values with different map properties such as value size, Jann reported that a case was not covered yet when a given alu op is used in both "ptr_reg += reg" and "numeric_reg += reg" from different branches where we would incorrectly try to sanitize based on the pointer's limit. Catch this corner case and reject the program instead. Fixes: 979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| * Merge branch 'udpv6_sendmsg-addr_any-fix'Alexei Starovoitov2019-01-052-7/+54
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Andrey Ignatov says: ==================== The patch set fixes BSD'ism in sys_sendmsg to rewrite unspecified destination IPv6 for unconnected UDP sockets in sys_sendmsg with [::1] in case when either CONFIG_CGROUP_BPF is enabled or when sys_sendmsg BPF hook sets destination IPv6 to [::]. Patch 1 is the fix and provides more details. Patch 2 adds two test cases to verify the fix. v1->v2: * Fix compile error in patch 1. ==================== Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| | * selftests/bpf: Test [::] -> [::1] rewrite in sys_sendmsg in test_sock_addrAndrey Ignatov2019-01-051-3/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Test that sys_sendmsg BPF hook doesn't break sys_sendmsg behaviour to rewrite destination IPv6 = [::] with [::1] (BSD'ism). Two test cases are added: 1) User passes dst IPv6 = [::] and BPF_CGROUP_UDP6_SENDMSG program doesn't touch it. 2) User passes dst IPv6 != [::], but BPF_CGROUP_UDP6_SENDMSG program rewrites it with [::]. In both cases [::1] is used by sys_sendmsg code eventually and datagram is sent successfully for unconnected UDP socket. Example of relevant output: Test case: sendmsg6: set dst IP = [::] (BSD'ism) .. [PASS] Test case: sendmsg6: preserve dst IP = [::] (BSD'ism) .. [PASS] Signed-off-by: Andrey Ignatov <rdna@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
| | * bpf: Fix [::] -> [::1] rewrite in sys_sendmsgAndrey Ignatov2019-01-051-4/+4
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sys_sendmsg has supported unspecified destination IPv6 (wildcard) for unconnected UDP sockets since 876c7f41. When [::] is passed by user as destination, sys_sendmsg rewrites it with [::1] to be consistent with BSD (see "BSD'ism" comment in the code). This didn't work when cgroup-bpf was enabled though since the rewrite [::] -> [::1] happened before passing control to cgroup-bpf block where fl6.daddr was updated with passed by user sockaddr_in6.sin6_addr (that might or might not be changed by BPF program). That way if user passed [::] as dst IPv6 it was first rewritten with [::1] by original code from 876c7f41, but then rewritten back with [::] by cgroup-bpf block. It happened even when BPF_CGROUP_UDP6_SENDMSG program was not present (CONFIG_CGROUP_BPF=y was enough). The fix is to apply BSD'ism after cgroup-bpf block so that [::] is replaced with [::1] no matter where it came from: passed by user to sys_sendmsg or set by BPF_CGROUP_UDP6_SENDMSG program. Fixes: 1cedee13d25a ("bpf: Hooks for sys_sendmsg") Reported-by: Nitin Rawat <nitin.rawat@intel.com> Signed-off-by: Andrey Ignatov <rdna@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
* | smc: move unhash as early as possible in smc_release()Cong Wang2019-01-071-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In smc_release() we release smc->clcsock before unhash the smc sock, but a parallel smc_diag_dump() may be still reading smc->clcsock, therefore this could cause a use-after-free as reported by syzbot. Reported-and-tested-by: syzbot+fbd1e5476e4c94c7b34e@syzkaller.appspotmail.com Fixes: 51f1de79ad8e ("net/smc: replace sock_put worker by socket refcounting") Cc: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reported-by: syzbot+0bf2e01269f1274b4b03@syzkaller.appspotmail.com Reported-by: syzbot+e3132895630f957306bc@syzkaller.appspotmail.com Signed-off-by: David S. Miller <davem@davemloft.net>
* | phy: ti: Fix compilation failures without REGMAPJason Gunthorpe2019-01-071-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This driver requires regmap or the compile fails: drivers/phy/ti/phy-gmii-sel.c:43:27: error: array type has incomplete element type ‘struct reg_field’ const struct reg_field (*regfields)[PHY_GMII_SEL_LAST]; Add it to kconfig. Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: bridge: fix a bug on using a neighbour cache entry without checking its ↵JianJhen Chen2019-01-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | state When handling DNAT'ed packets on a bridge device, the neighbour cache entry from lookup was used without checking its state. It means that a cache entry in the NUD_STALE state will be used directly instead of entering the NUD_DELAY state to confirm the reachability of the neighbor. This problem becomes worse after commit 2724680bceee ("neigh: Keep neighbour cache entries if number of them is small enough."), since all neighbour cache entries in the NUD_STALE state will be kept in the neighbour table as long as the number of cache entries does not exceed the value specified in gc_thresh1. This commit validates the state of a neighbour cache entry before using the entry. Signed-off-by: JianJhen Chen <kchen@synology.com> Reviewed-by: JinLin Chen <jlchen@synology.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | tipc: fix memory leak in tipc_nl_compat_publ_dumpGustavo A. R. Silva2019-01-071-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | There is a memory leak in case genlmsg_put fails. Fix this by freeing *args* before return. Addresses-Coverity-ID: 1476406 ("Resource leak") Fixes: 46273cf7e009 ("tipc: fix a missing check of genlmsg_put") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | cdc_ether: trivial whitespace readability fixBjørn Mork2019-01-071-15/+11
| | | | | | | | | | | | | | | | This function is unreadable enough without indenting mismatches and unnecessary line breaks. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | rds: use DIV_ROUND_UP instead of ceilJacob Wen2019-01-074-9/+5
| | | | | | | | | | | | | | Yes indeed, DIV_ROUND_UP is in kernel.h. Signed-off-by: Jacob Wen <jian.w.wen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | r8169: don't try to read counters if chip is in a PCI power-save stateHeiner Kallweit2019-01-071-2/+4
| | | | | | | | | | | | | | | | | | | | | | Avoid log spam caused by trying to read counters from the chip whilst it is in a PCI power-save state. Reference: https://bugzilla.kernel.org/show_bug.cgi?id=107421 Fixes: 1ef7286e7f36 ("r8169: Dereference MMIO address immediately before use") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | can: gw: ensure DLC boundaries after CAN frame modificationOliver Hartkopp2019-01-071-3/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Muyu Yu provided a POC where user root with CAP_NET_ADMIN can create a CAN frame modification rule that makes the data length code a higher value than the available CAN frame data size. In combination with a configured checksum calculation where the result is stored relatively to the end of the data (e.g. cgw_csum_xor_rel) the tail of the skb (e.g. frag_list pointer in skb_shared_info) can be rewritten which finally can cause a system crash. Michael Kubecek suggested to drop frames that have a DLC exceeding the available space after the modification process and provided a patch that can handle CAN FD frames too. Within this patch we also limit the length for the checksum calculations to the maximum of Classic CAN data length (8). CAN frames that are dropped by these additional checks are counted with the CGW_DELETED counter which indicates misconfigurations in can-gw rules. This fixes CVE-2019-3701. Reported-by: Muyu Yu <ieatmuttonchuan@gmail.com> Reported-by: Marcus Meissner <meissner@suse.de> Suggested-by: Michal Kubecek <mkubecek@suse.cz> Tested-by: Muyu Yu <ieatmuttonchuan@gmail.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= v3.2 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: replace pci_{,un}map_sg with dma_{,un}map_sgStephen Warren2019-01-071-8/+7
| | | | | | | | | | | | | | | | | | | | pci_{,un}map_sg are deprecated and replaced by dma_{,un}map_sg. This is especially relevant since the rest of the driver uses the DMA API. Fix the driver to use the replacement APIs. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: Get rid of page operation after dma_alloc_coherentStephen Warren2019-01-072-39/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch solves a crash at the time of mlx4 driver unload or system shutdown. The crash occurs because dma_alloc_coherent() returns one value in mlx4_alloc_icm_coherent(), but a different value is passed to dma_free_coherent() in mlx4_free_icm_coherent(). In turn this is because when allocated, that pointer is passed to sg_set_buf() to record it, then when freed it is re-calculated by calling lowmem_page_address(sg_page()) which returns a different value. Solve this by recording the value that dma_alloc_coherent() returns, and passing this to dma_free_coherent(). This patch is roughly equivalent to commit 378efe798ecf ("RDMA/hns: Get rid of page operation after dma_alloc_coherent"). Based-on-code-from: Christoph Hellwig <hch@lst.de> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ipv6: Take rcu_read_lock in __inet6_bind for mapped addressesDavid Ahern2019-01-051-1/+4
|/ | | | | | | | | I realized the last patch calls dev_get_by_index_rcu in a branch not holding the rcu lock. Add the calls to rcu_read_lock and rcu_read_unlock. Fixes: ec90ad334986 ("ipv6: Consider sk_bound_dev_if when binding a socket to a v4 mapped address") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: Consider sk_bound_dev_if when binding a socket to a v4 mapped addressDavid Ahern2019-01-051-1/+10
| | | | | | | | | | | Similar to c5ee066333eb ("ipv6: Consider sk_bound_dev_if when binding a socket to an address"), binding a socket to v4 mapped addresses needs to consider if the socket is bound to a device. This problem also exists from the beginning of git history. Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: fix Kconfig when driver is not a moduleJeff Kirsher2019-01-041-1/+1
| | | | | | | | | | | | | | | | | | | The new ability added to the driver to use mii_bus to handle MII related ioctls is causing compile issues when the driver is compiled into the kernel (i.e. not a module). The problem was in selecting MDIO_DEVICE instead of the preferred PHYLIB Kconfig option. The reason being that MDIO_DEVICE had a dependency on PHYLIB and would be compiled as a module when PHYLIB was a module, no matter whether ixgbe was compiled into the kernel. CC: Dave Jones <davej@codemonkey.org.uk> CC: Steve Douthit <stephend@silicom-usa.com> CC: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Reviewed-by: Stephen Douthit <stephend@silicom-usa.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-16 02:29:30 +0100