summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ASoC: Make pmdown_time a longMark Brown2010-02-172-2/+2
| | | | | | | Fixes a warning. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* ASoC: TWL4030: Use codec defaults for Headset initial configurationPeter Ujfalusi2010-02-171-2/+2
| | | | | | | | | Disable the amplifiers for the headset outputs, and do not select routings by default to the headset outputs. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Correct the OSCSET calculationPeter Ujfalusi2010-02-161-1/+1
| | | | | | | | | | | OSCSET calculation was not correct in case of 44.1KHz sampling rate. With small adjustment both 48 and 44.1 KHz calculation now gives the correct value. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Clearing FIFOFLUSH flag before playbackPeter Ujfalusi2010-02-161-0/+3
| | | | | | | | | | In repeated playback the FIFOFLUSH bit remained set, and never has been cleared. Clear it during the setup phase. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Make pmdown_time runtime configurableMark Brown2010-02-161-0/+27
| | | | | | | | Provide a sysfs file allowing userspace to inspect and change the pmdown_time setting at runtime. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* ASoC: Make pmdown_time a per-card settingMark Brown2010-02-162-1/+5
| | | | | | | | | | Make the pmdown_time a per-card setting rather than a global one, initialised before the card initialisation runs. This allows cards to override the default setting if it makes sense to do so (for example, due to an unavoidable pop). Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* ASoC: Add WM2000 driverMark Brown2010-02-125-0/+999
| | | | | | | | | | The WM2000 is a low power, high quality handset receiver speaker driver with Wolfson myZone™ Ambient Noise Cancellation (ANC). It provides enhanced voice communication quality in a noisy environment if the handset acoustics are designed appropriately. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* ASoC: fix compile breakage if CONFIG_SH_DMA_API=y && CONFIG_SND_SIU_MIGOR!=nGuennadi Liakhovetski2010-02-121-0/+1
| | | | | | | | | Audio on Migo-R cannot work if CONFIG_SH_DMA_API=y, but compilation should not break anyway. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Add ASoC support for Devkit8000Thomas Weber2010-02-112-6/+8
| | | | | | | | | | This patch expands the omap3beagle sound soc for the beagle board clone DevKit8000. Signed-off-by: Thomas Weber <weber@corscience.de> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Typo. s/Freecale/Freescale/Paul Menzel2010-02-101-1/+1
| | | | | | Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: TWL4030: Add supply for audio serial interface controlPeter Ujfalusi2010-02-101-1/+13
| | | | | | | | | | | | | | | | | | The serial interface (TDM/I2S) for the audio block have been constantly enabled. Introduce a new DAPM_SUPPLY for handling the AIF_EN bit, so the interface is only enabled, when there is a need for it. For example when only the analog loopback is enabled, there is no need to keep the serial interface active. I have added the persons who contributed to the Voice path of twl4030 codec driver, so they might have the ability to test this patch, and send an update for the Voice path, if it is necessary Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: cs4270: enable regulators at probe timeDaniel Mack2010-02-101-0/+10
| | | | | | | | | Enable the bulk regulators at probe time so we can safely disable them again when going to suspend without confusing the reference counter. Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: add phycore-ac97 sound supportMark Brown2010-02-102-0/+92
| | | | | | | | | This patch adds sound support for Phytec PhyCORE / PhyCARD modules in AC97 mode. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: pandora: Add DAC regulator supportGrazvydas Ignotas2010-02-051-5/+37
| | | | | | | | | | Pandora's external DAC is connected to VSIM TWL4030 supply, so let's start switching it too to save more power. Also DAC got it's own DAPM handler. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Merge branch 'for-2.6.33' into for-2.6.34Mark Brown2010-02-051-0/+1
|\
| * ASoC: pandora: Add APLL supply to fix audio outputGrazvydas Ignotas2010-02-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | Pandora's external DAC is using 256*Fs output from the TWL4030 codec, and TWL4030 needs to have APLL enabled for it's 256*Fs output to function. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: TWL4030: Module unloading fixPeter Ujfalusi2010-02-041-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | The module unloading path had several problems: - it freed up the private structure twice - it freed up the codec structure, which was allocated as part of the private structure - it did not freed up the reg_cache - it did not unregistered the dais and the codec Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: Add WM8912 DAC supportMark Brown2010-02-041-18/+72
| | | | | | | | | | | | | | | | | | The WM8912 is a DAC only device register compatible with the WM8904 CODEC with ADC portions omitted. Support it within the WM8904 driver based on the configured I2C device name. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Optimise WM8904 output stage power controlMark Brown2010-02-041-7/+27
| | | | | | | | | | | | | | | | | | | | Handle the output PGAs as part of the output powerup since they can never be powered separately and reorder things so that we remove the output shorts after both line and headphone outputs have been brought up, minimising the opportunity for any issues. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Add support for BIAS_OFF when idle to WM8904Mark Brown2010-02-041-13/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | As well as disabling the biases of the CODEC the drop into BIAS_OFF will also disable all the regulators powering the CODEC, allowing even greater power savings on appropriately configured systems. Since the regulator API does not currently provide notification when regulators are disabled we assume that this always happens when we stop using the regulators. Once 2.6.34 is merged this code can be optimised to only sync the cache when power was actually removed. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Disable WM8993 regulators when turning bias offMark Brown2010-02-041-9/+45
| | | | | | | | | | | | | | | | | | | | | | While the regulators are disabled we cache all register writes. Currently we assume that the regulator disable actually takes effect, after the merge with the regulator tree in 2.6.34 the regulator API will be able to notify us if the power is actually removed (due to constraints or regulator sharing it may not be). Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Initial WM8993 regulator API hookupMark Brown2010-02-041-3/+38
| | | | | | | | | | | | | | | | At the minute the regulators are simply enabled for the entire lifetime of the device. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Convert WM8993 to use shared cache I/O codeMark Brown2010-02-041-109/+43
| | | | | | | | | | | | | | Saves a little bit of code duplication. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Add a cache_sync bit to the CODEC structureMark Brown2010-02-042-5/+16
| | | | | | | | | | | | | | | | | | | | Add a bit to the CODEC structure indicating if a cache sync is required. By default this will be set if a cache only write is done to a soc-cache register cache. This allows us to avoid syncing the cache back after using cache only writes if there were no changes. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Allow CODECs to ask soc-cache to suppress physical writesMark Brown2010-02-032-2/+25
| | | | | | | | | | | | | | | | | | | | | | Currently the soc-cache code will always write to the device, meaning that we need the device to be powered and active at pretty much all times the system is active. Allowing cache only writes lays some groundwork for future enhancements to allow devices to be put into a full off state when the audio subsystem is idle. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: fix compilation breakage in sound/soc/sh/fsi.cGuennadi Liakhovetski2010-02-031-23/+17
| | | | | | | | | | | | | | | | | | | | | | ctrl_outl() has become void at some point, which breaks compilation of fsi.c. Make writing functions void, as their output is anyway not evaluated, and use __raw_writel and __raw_readl instead of deprecated ctrl_outl and ctrl_inl respectively. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: fix PXA SSP port resumeDaniel Mack2010-02-021-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | Unconditionally save the register states when suspending and restore them again at resume time. Register contents were not preserved over suspend, and hence the driver takes false assumptions about them. The clock must be enabled to access the register block. Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: Fix continuation line formatsJoe Perches2010-02-021-2/+1
| | | | | | | | | | | | | | | | | | String constants that are continued on subsequent lines with \ are not good. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: Fix BCLK calculation of WM8994Joonyoung Shim2010-02-021-5/+2
| | | | | | | | | | | | | | | | This fixes BCLK calculation and removes unnecessary check code. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: Fix WM8994 dependencyMark Brown2010-02-021-1/+1
| | | | | | | | | | | | | | The dependency on MFD_WM8994 rather than I2C went awry. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Add WM8994 CODEC driverMark Brown2010-02-014-0/+3902
| | | | | | | | | | | | | | | | | | | | | | The WM8994 is a highly integrated ultra-low power hi-fi audio subsystem designed for smartphones and other portable devices rich in multimedia features. It provides advanced digital mixing facilities enabling low power high quality interconnection of CPU, baseband and other audio sources through flexible digital and analogue routing, and integrates a class W headphone driver and stereo class D speaker drivers. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: Activate DCS correction for WM8993Mark Brown2010-02-011-1/+2
| | | | | | | | | | | | | | Use a two code correction for optimal performance. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Improved wm_hubs headphone handlingMark Brown2010-02-013-26/+130
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Perform DC servo offset calibration using a series update sequence rather than startup update sequence, tuning the configuration of the WM8993 DC servo to make best use of this. Also introduce currently unused data allowing us to correct for any systematic errors in the DC servo calibration results and an alternative startup path for the headphone output which performs better with some chip revisions. The alternative setup sequence is enabled for WM8993. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Fix continuation line formatsJoe Perches2010-02-013-10/+4
| | | | | | | | | | | | | | | | | | String constants that are continued on subsequent lines with \ are not good. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: improve MCLKDIV calculation in wm8978, when OPCLK is not usedGuennadi Liakhovetski2010-02-011-37/+78
| | | | | | | | | | | | | | | | | | | | | | In case, if OPCLK is not used, and PLL is used for driving the codec, the choice of PLL output frequency could result in a needlessly imprecise system clock frequency. Use an iterative process to select a precise configuration. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: clean up wm8974 and wm8978 clock divider handlingGuennadi Liakhovetski2010-01-295-41/+9
| | | | | | | | | | | | | | | | | | | | | | | | wm8974 and wm8978 codec drivers control DAC and ADC oversampling rates in their .set_clkdiv() methods, which is wrong, because these are simple boolean switches and not clock dividers. Move these bits to sound controls. Also remove manual configuration of the MCLK divider in wm8978, since it is configured automatically. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | Merge branch 'for-2.6.33' into for-2.6.34Mark Brown2010-01-292-2/+2
|\|
| * ASoC: AM3517: ASoC driver not getting compiledAnuj Aggarwal2010-01-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | Commit 761c9d45 (ASoC: Fix build of OMAP sound drivers) changes CONFIG_MACH_OMAP3517EVM -> CONFIG_SND_OMAP_SOC_OMAP3517EVM in the Makefile. Whereas the config option defined in Kconfig is SND_OMAP_SOC_AM3517EVM. Because of this, ASoC driver for AM3517 was not getting compiled. Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
| * ASoC: AIC23: Fixing writes to non-existing registers in resume functionAnuj Aggarwal2010-01-291-1/+1
| | | | | | | | | | | | | | | | | | | | Commit e9ff5eb2 (Fixing infinite loop in resume path) uses wrong AIC23 register in resume function because of which register writes happen on some non-existing registers. Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: remove bogus SLEEP mode from wm8978 driverGuennadi Liakhovetski2010-01-291-5/+0
| | | | | | | | | | | | | | | | | | | | Tests showed, that bit 6 of the WM8978_POWER_MANAGEMENT_2 register of wm8978 affects codec clocks. Being useless for suspend / resume, it cannot be used in bias-level control either. Remove this bit handling. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: add support for the sh7722 Migo-R boardGuennadi Liakhovetski2010-01-293-0/+232
| | | | | | | | | | | | | | | | | | | | Add support for audio on sh7722-based Migo-R boards, using SIU and wm8978 codec, recording via external microphone and playback via headphones are implemented. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: AC97: SMDK-WM9713: Convert notes from cset to ssetJassi Brar2010-01-291-16/+7
| | | | | | | | | | | | | | | | | | It's more robust when references are provided in control names rather than numid. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: Set codec->dev for AC97 devicesMark Brown2010-01-281-0/+1
| | | | | | | | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Add TLV information and additional volumes to WM9713Mark Brown2010-01-281-16/+44
| | | | | | | | | | | | | | | | Also renames a few things to make volumes and switches match up in alsamixer. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: Remove version display from WM9713Mark Brown2010-01-281-4/+0
| | | | | | | | | | | | | | | | The version isn't being updated or used, the kernel revision tracking is enough. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | ASoC: TWL4030: Modify codec default settingsPeter Ujfalusi2010-01-281-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the legacy default register configuration, which left some internal components on. Now we have either DAPM, or other ways to control these bits, so there is no need to enable them by default. The affected parts: Disable ADCL and ADCR Disable ARXL2 and ARXR2 analog PGA (playback) Disable APLL by default Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: fsi: Add spin lock operation for accessing shared areaKuninori Morimoto2010-01-281-3/+26
| | | | | | | | | | | | | | | | | | fsi_master_xxx function should be protected by spin lock, because it are used from both FSI-A and FSI-B. Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: add a WM8978 codec driverGuennadi Liakhovetski2010-01-274-0/+1219
| | | | | | | | | | | | | | | | | | | | | | The WM8978 codec from Wolfson Microelectronics is very similar to wm8974, but is stereo and also has some differences in pin configuration and internal signal routing. This driver is based on wm8974 and takes the differences into account. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: Note jumper settings for smdk_wm9713 driver on SMDK6410Mark Brown2010-01-271-0/+6
| | | | | | | | | | | | | | | | The board supports both GPIO sets for the AC97 bus and the analogue outputs can be switched between this and the WM8580 so add some comments saying what the setup the standard kernel expects is. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: AC97: S3C2443: Remove unused driverJassi Brar2010-01-274-462/+0
| | | | | | | | | | | | | | | | | | Since, we have generic AC97 controller driver and all the machines have moved to that, there is no need for old s3c2443-ac97.c to exist. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-15 04:25:37 +0100