| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the PCI PHY found in the Amlogic AXG SoC Family.
This will allow to mutualize code in pci-meson.c between AXG and G12A
SoC.
This PHY also uses and chains an analog PHY, which on AXG platform
is needed to have reliable PCIe communication.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the MIPI analog PHY which is also used for PCIE
found in the Amlogic AXG SoC Family.
MIPI or PCIE selection is done by the #phy-cells, making the mode
static and exclusive.
For now only PCIE functionality is supported.
This PHY will be used to replace the mipi_enable clock gating logic
which was mistakenly added in the clock subsystem. This also activates
a non documented band gap bit in those registers that allows reliable
PCIE clock signal generation on AXG platforms.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Now that a new PHYs has been introduced for AXG SoC family, update
dt bindings documentation.
Please note that this breaks backward compatibility but as not a single
devicetree uses that yet that seems ok.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
| |
|
|
|
|
|
|
|
| |
Add documentation for the shared MIPI/PCIE analog PHY found in AXG
SoCs.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
| |
|
|
|
|
|
|
| |
Add documentation for PCIE PHYs found in AXG SoCs.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
| | |
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, the single-target build does not work when two
or more sub-directories are given:
$ make fs/ kernel/ lib/
CALL scripts/checksyscalls.sh
CALL scripts/atomic/check-atomics.sh
DESCEND objtool
make[2]: Nothing to be done for 'kernel/'.
make[2]: Nothing to be done for 'fs/'.
make[2]: Nothing to be done for 'lib/'.
Make it work properly.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Since commit 89b9060987d9 ("kconfig: Add yes2modconfig and
mod2yesconfig targets.") forgot to clear SYMBOL_VALID bit after
changing to y or m, these targets did not save the changes.
Call sym_clear_all_valid() so that all symbols are revalidated.
Fixes: 89b9060987d9 ("kconfig: Add yes2modconfig and mod2yesconfig targets.")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
kallsyms_token_table[] only contains ASCII characters. It should be
char instead of u8.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The symbol table is extended every 10000 addition by using realloc(),
where data copy might occur to the new buffer.
To decrease the amount of possible data copy, let's change the table
to store the pointer.
The symbol type + symbol name part is appended at the end of
(struct sym_entry), and allocated together with the struct body.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| | |
I will use 'sym' for the point to struce sym_entry in the next commit.
Rename 'sym', 'stype' to 'name', 'type', which are more intuitive.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In old days, the "host-progs" syntax was used for specifying host
programs. It was renamed to the current "hostprogs-y" in 2004.
It is typically useful in scripts/Makefile because it allows Kbuild to
selectively compile host programs based on the kernel configuration.
This commit renames like follows:
always -> always-y
hostprogs-y -> hostprogs
So, scripts/Makefile will look like this:
always-$(CONFIG_BUILD_BIN2C) += ...
always-$(CONFIG_KALLSYMS) += ...
...
hostprogs := $(always-y) $(always-m)
I think this makes more sense because a host program is always a host
program, irrespective of the kernel configuration. We want to specify
which ones to compile by CONFIG options, so always-y will be handier.
The "always", "hostprogs-y", "hostprogs-m" will be kept for backward
compatibility for a while.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The difference between "always" and "extra-y" is that the targets
listed in $(always) are always built, whereas the ones in $(extra-y)
are built only when KBUILD_BUILTIN is set.
So, "make modules" does not build the targets in $(extra-y).
vmlinux.lds is only needed for linking vmlinux. So, adding it to extra-y
is more correct. In fact, arch/x86/kernel/Makefile does this.
Fix the example code.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Running randconfig on arm64 using KCONFIG_SEED=0x40C5E904 (e.g. on v5.5)
produces the .config with CONFIG_EFI=y and CONFIG_CPU_BIG_ENDIAN=y,
which does not meet the !CONFIG_CPU_BIG_ENDIAN dependency.
This is because the user choice for CONFIG_CPU_LITTLE_ENDIAN vs
CONFIG_CPU_BIG_ENDIAN is set by randomize_choice_values() after the
value of CONFIG_EFI is calculated.
When this happens, the has_changed flag should be set.
Currently, it takes the result from the last iteration. It should
accumulate all the results of the loop.
Fixes: 3b9a19e08960 ("kconfig: loop as long as we changed some symbols in randconfig")
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull new zonefs file system from Damien Le Moal:
"Zonefs is a very simple file system exposing each zone of a zoned
block device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of
changes needed in the application while at the same time allowing the
use of zoned block devices with various programming languages other
than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs"
* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Add documentation
fs: New zonefs file system
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add the new file Documentation/filesystems/zonefs.txt to document
zonefs principles and user-space tool usage.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
zonefs is a very simple file system exposing each zone of a zoned block
device as a file. Unlike a regular file system with zoned block device
support (e.g. f2fs), zonefs does not hide the sequential write
constraint of zoned block devices to the user. Files representing
sequential write zones of the device must be written sequentially
starting from the end of the file (append only writes).
As such, zonefs is in essence closer to a raw block device access
interface than to a full featured POSIX file system. The goal of zonefs
is to simplify the implementation of zoned block device support in
applications by replacing raw block device file accesses with a richer
file API, avoiding relying on direct block device file ioctls which may
be more obscure to developers. One example of this approach is the
implementation of LSM (log-structured merge) tree structures (such as
used in RocksDB and LevelDB) on zoned block devices by allowing SSTables
to be stored in a zone file similarly to a regular file system rather
than as a range of sectors of a zoned device. The introduction of the
higher level construct "one file is one zone" can help reducing the
amount of changes needed in the application as well as introducing
support for different application programming languages.
Zonefs on-disk metadata is reduced to an immutable super block to
persistently store a magic number and optional feature flags and
values. On mount, zonefs uses blkdev_report_zones() to obtain the device
zone configuration and populates the mount point with a static file tree
solely based on this information. E.g. file sizes come from the device
zone type and write pointer offset managed by the device itself.
The zone files created on mount have the following characteristics.
1) Files representing zones of the same type are grouped together
under a common sub-directory:
* For conventional zones, the sub-directory "cnv" is used.
* For sequential write zones, the sub-directory "seq" is used.
These two directories are the only directories that exist in zonefs.
Users cannot create other directories and cannot rename nor delete
the "cnv" and "seq" sub-directories.
2) The name of zone files is the number of the file within the zone
type sub-directory, in order of increasing zone start sector.
3) The size of conventional zone files is fixed to the device zone size.
Conventional zone files cannot be truncated.
4) The size of sequential zone files represent the file's zone write
pointer position relative to the zone start sector. Truncating these
files is allowed only down to 0, in which case, the zone is reset to
rewind the zone write pointer position to the start of the zone, or
up to the zone size, in which case the file's zone is transitioned
to the FULL state (finish zone operation).
5) All read and write operations to files are not allowed beyond the
file zone size. Any access exceeding the zone size is failed with
the -EFBIG error.
6) Creating, deleting, renaming or modifying any attribute of files and
sub-directories is not allowed.
7) There are no restrictions on the type of read and write operations
that can be issued to conventional zone files. Buffered, direct and
mmap read & write operations are accepted. For sequential zone files,
there are no restrictions on read operations, but all write
operations must be direct IO append writes. mmap write of sequential
files is not allowed.
Several optional features of zonefs can be enabled at format time.
* Conventional zone aggregation: ranges of contiguous conventional
zones can be aggregated into a single larger file instead of the
default one file per zone.
* File ownership: The owner UID and GID of zone files is by default 0
(root) but can be changed to any valid UID/GID.
* File access permissions: the default 640 access permissions can be
changed.
The mkzonefs tool is used to format zoned block devices for use with
zonefs. This tool is available on Github at:
git@github.com:damien-lemoal/zonefs-tools.git.
zonefs-tools also includes a test suite which can be run against any
zoned block device, including null_blk block device created with zoned
mode.
Example: the following formats a 15TB host-managed SMR HDD with 256 MB
zones with the conventional zones aggregation feature enabled.
$ sudo mkzonefs -o aggr_cnv /dev/sdX
$ sudo mount -t zonefs /dev/sdX /mnt
$ ls -l /mnt/
total 0
dr-xr-xr-x 2 root root 1 Nov 25 13:23 cnv
dr-xr-xr-x 2 root root 55356 Nov 25 13:23 seq
The size of the zone files sub-directories indicate the number of files
existing for each type of zones. In this example, there is only one
conventional zone file (all conventional zones are aggregated under a
single file).
$ ls -l /mnt/cnv
total 137101312
-rw-r----- 1 root root 140391743488 Nov 25 13:23 0
This aggregated conventional zone file can be used as a regular file.
$ sudo mkfs.ext4 /mnt/cnv/0
$ sudo mount -o loop /mnt/cnv/0 /data
The "seq" sub-directory grouping files for sequential write zones has
in this example 55356 zones.
$ ls -lv /mnt/seq
total 14511243264
-rw-r----- 1 root root 0 Nov 25 13:23 0
-rw-r----- 1 root root 0 Nov 25 13:23 1
-rw-r----- 1 root root 0 Nov 25 13:23 2
...
-rw-r----- 1 root root 0 Nov 25 13:23 55354
-rw-r----- 1 root root 0 Nov 25 13:23 55355
For sequential write zone files, the file size changes as data is
appended at the end of the file, similarly to any regular file system.
$ dd if=/dev/zero of=/mnt/seq/0 bs=4K count=1 conv=notrunc oflag=direct
1+0 records in
1+0 records out
4096 bytes (4.1 kB, 4.0 KiB) copied, 0.000452219 s, 9.1 MB/s
$ ls -l /mnt/seq/0
-rw-r----- 1 root root 4096 Nov 25 13:23 /mnt/seq/0
The written file can be truncated to the zone size, preventing any
further write operation.
$ truncate -s 268435456 /mnt/seq/0
$ ls -l /mnt/seq/0
-rw-r----- 1 root root 268435456 Nov 25 13:49 /mnt/seq/0
Truncation to 0 size allows freeing the file zone storage space and
restart append-writes to the file.
$ truncate -s 0 /mnt/seq/0
$ ls -l /mnt/seq/0
-rw-r----- 1 root root 0 Nov 25 13:49 /mnt/seq/0
Since files are statically mapped to zones on the disk, the number of
blocks of a file as reported by stat() and fstat() indicates the size
of the file zone.
$ stat /mnt/seq/0
File: /mnt/seq/0
Size: 0 Blocks: 524288 IO Block: 4096 regular empty file
Device: 870h/2160d Inode: 50431 Links: 1
Access: (0640/-rw-r-----) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2019-11-25 13:23:57.048971997 +0900
Modify: 2019-11-25 13:52:25.553805765 +0900
Change: 2019-11-25 13:52:25.553805765 +0900
Birth: -
The number of blocks of the file ("Blocks") in units of 512B blocks
gives the maximum file size of 524288 * 512 B = 256 MB, corresponding
to the device zone size in this example. Of note is that the "IO block"
field always indicates the minimum IO size for writes and corresponds
to the device physical sector size.
This code contains contributions from:
* Johannes Thumshirn <jthumshirn@suse.de>,
* Darrick J. Wong <darrick.wong@oracle.com>,
* Christoph Hellwig <hch@lst.de>,
* Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> and
* Ting Yao <tingyao@hust.edu.cn>.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.
Fixes: 4e6437f12d6e ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull cifs fixes from Steve French:
"13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:
- Important fix for multichannel and for modefromsid mounts.
- Two reconnect fixes
- Addition of SMB3 change notify support
- Backup tools fix
- A few additional minor debug improvements (tracepoints and
additional logging found useful during testing this week)"
* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add defines for new information level, FileIdInformation
smb3: print warning once if posix context returned on open
smb3: add one more dynamic tracepoint missing from strict fsync path
cifs: fix mode bits from dir listing when mounted with modefromsid
cifs: fix channel signing
cifs: add SMB3 change notification support
cifs: make multichannel warning more visible
cifs: fix soft mounts hanging in the reconnect code
cifs: Add tracepoints for errors on flush or fsync
cifs: log warning message (once) if out of disk space
cifs: fail i/o on soft mounts if sessionsetup errors out
smb3: fix problem with null cifs super block with previous patch
SMB3: Backup intent flag missing from some more ops
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
See MS-FSCC 2.4.43. Valid to be quried from most
Windows servers (among others).
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
SMB3.1.1 POSIX Context processing is not complete yet - so print warning
(once) if server returns it on open.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We didn't have a dynamic trace point for catching errors in
file_write_and_wait_range error cases in cifs_strict_fsync.
Since not all apps check for write behind errors, it can be
important for debugging to be able to trace these error
paths.
Suggested-and-reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When mounting with -o modefromsid, the mode bits are stored in an
ACE. Directory enumeration (e.g. ls -l /mnt) triggers an SMB Query Dir
which does not include ACEs in its response. The mode bits in this
case are silently set to a default value of 755 instead.
This patch marks the dentry created during the directory enumeration
as needing re-evaluation (i.e. additional Query Info with ACEs) so
that the mode bits can be properly extracted.
Quick repro:
$ mount.cifs //win19.test/data /mnt -o ...,modefromsid
$ touch /mnt/foo && chmod 751 /mnt/foo
$ stat /mnt/foo
# reports 751 (OK)
$ sleep 2
# dentry older than 1s by default get invalidated
$ ls -l /mnt
# since dentry invalid, ls does a Query Dir
# and reports foo as 755 (WRONG)
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The server var was accidentally used as an iterator over the global
list of connections, thus overwritten the passed argument. This
resulted in the wrong signing key being returned for extra channels.
Fix this by using a separate var to iterate.
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
A commonly used SMB3 feature is change notification, allowing an
app to be notified about changes to a directory. The SMB3
Notify request blocks until the server detects a change to that
directory or its contents that matches the completion flags
that were passed in and the "watch_tree" flag (which indicates
whether subdirectories under this directory should be also
included). See MS-SMB2 2.2.35 for additional detail.
To use this simply pass in the following structure to ioctl:
struct __attribute__((__packed__)) smb3_notify {
uint32_t completion_filter;
bool watch_tree;
} __packed;
using CIFS_IOC_NOTIFY 0x4005cf09
or equivalently _IOW(CIFS_IOCTL_MAGIC, 9, struct smb3_notify)
SMB3 change notification is supported by all major servers.
The ioctl will block until the server detects a change to that
directory or its subdirectories (if watch_tree is set).
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When no interfaces are returned by the server we cannot open multiple
channels. Make it more obvious by reporting that to the user at the
VFS log level.
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
RHBZ: 1795423
This is the SMB1 version of a patch we already have for SMB2
In recent DFS updates we have a new variable controlling how many times we will
retry to reconnect the share.
If DFS is not used, then this variable is initialized to 0 in:
static inline int
dfs_cache_get_nr_tgts(const struct dfs_cache_tgt_list *tl)
{
return tl ? tl->tl_numtgts : 0;
}
This means that in the reconnect loop in smb2_reconnect() we will immediately wrap retries to -1
and never actually get to pass this conditional:
if (--retries)
continue;
The effect is that we no longer reach the point where we fail the commands with -EHOSTDOWN
and basically the kernel threads are virtually hung and unkillable.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Makes it easier to debug errors on writeback that happen later,
and are being returned on flush or fsync
For example:
writetest-17829 [002] .... 13583.407859: cifs_flush_err: ino=90 rc=-28
Signed-off-by: Steve French <stfrench@microsoft.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We ran into a confusing problem where an application wasn't checking
return code on close and so user didn't realize that the application
ran out of disk space. log a warning message (once) in these
cases. For example:
[ 8407.391909] Out of space writing to \\oleg-server\small-share
Signed-off-by: Steve French <stfrench@microsoft.com>
Reported-by: Oleg Kravtsov <oleg@tuxera.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
RHBZ: 1579050
If we have a soft mount we should fail commands for session-setup
failures (such as the password having changed/ account being deleted/ ...)
and return an error back to the application.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add check for null cifs_sb to create_options helper
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When "backup intent" is requested on the mount (e.g. backupuid or
backupgid mount options), the corresponding flag was missing from
some of the operations.
Change all operations to use the macro cifs_create_options() to
set the backup intent flag if needed.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vboxfs from Al Viro:
"This is the VirtualBox guest shared folder support by Hans de Goede,
with fixups for fs_parse folded in to avoid bisection hazards from
those API changes..."
* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Add VirtualBox guest shared folder (vboxsf) support
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.
This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When a system suspends, the local APIC is disabled in the suspend sequence,
but the IOAPIC is left in the current state. This means unmasked interrupt
lines stay unmasked. This is usually the case for IOAPIC pin 9 to which the
ACPI interrupt is connected.
That means that in suspended state the IOAPIC can respond to an external
interrupt, e.g. the wakeup via keyboard/RTC/ACPI, but the interrupt message
cannot be handled by the disabled local APIC. As a consequence the Remote
IRR bit is set, but the local APIC does not send an EOI to acknowledge
it. This causes the affected interrupt line to become stale and the stale
Remote IRR bit will cause a hang when __synchronize_hardirq() is invoked
for that interrupt line.
To prevent this, mask all IOAPIC entries before disabling the local
APIC. The resume code already has the unmask operation inside.
[ tglx: Massaged changelog ]
Signed-off-by: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/1579076539-7267-1-git-send-email-TonyWWang-oc@zhaoxin.com
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
For hibernation the hypercall page must be disabled before the hibernation
image is created so that subsequent hypercall operations fail safely. On
resume the hypercall page has to be restored and reenabled to ensure proper
operation of the resumed kernel.
Implement the necessary suspend/resume callbacks.
[ tglx: Decrypted changelog ]
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1578350559-130275-1-git-send-email-decui@microsoft.com
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org>
Debugged-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Break an infinite loop when early parsing of the SRAT table is caused
by a subtable with zero length. Known to affect the ASUS WS X299 SAGE
motherboard with firmware version 1201 which has a large block of
zeros in its SRAT table. The kernel could boot successfully on this
board/firmware prior to the introduction of early parsing this table or
after a BIOS update.
[ bp: Fixup whitespace damage and commit message. Make it return 0 to
denote that there are no immovable regions because who knows what
else is broken in this BIOS. ]
Fixes: 02a3e3cdb7f1 ("x86/boot: Parse SRAT table and count immovable memory regions")
Signed-off-by: Steven Clarkson <sc@lambdal.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-acpi@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206343
Link: https://lkml.kernel.org/r/CAHKq8taGzj0u1E_i=poHUam60Bko5BpiJ9jn0fAupFUYexvdUQ@mail.gmail.com
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Tony reported a boot regression caused by the recent workaround for systems
which have a disabled (clock gate off) PIT.
On his machine the kernel fails to initialize the PIT because
apic_needs_pit() does not take into account whether the local APIC
interrupt delivery mode will actually allow to setup and use the local
APIC timer. This should be easy to reproduce with acpi=off on the
command line which also disables HPET.
Due to the way the PIT/HPET and APIC setup ordering works (APIC setup can
require working PIT/HPET) the information is not available at the point
where apic_needs_pit() makes this decision.
To address this, split out the interrupt mode selection from
apic_intr_mode_init(), invoke the selection before making the decision
whether PIT is required or not, and add the missing checks into
apic_needs_pit().
Fixes: c8c4076723da ("x86/timer: Skip PIT initialization on modern chipsets")
Reported-by: Anthony Buckley <tony.buckley000@gmail.com>
Tested-by: Anthony Buckley <tony.buckley000@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Daniel Drake <drake@endlessm.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206125
Link: https://lore.kernel.org/r/87sgk6tmk2.fsf@nanos.tec.linutronix.de
|
| |\ \ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP related functionality:
- Make the UP version of smp_call_function_single() match SMP
semantics when called for a not available CPU. Instead of emitting
a warning and assuming that the function call target is CPU0,
return a proper error code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()"
* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/up: Make smp_call_function_single() match SMP semantics
smp: Remove superfluous cond_func check in smp_call_function_many_cond()
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In CONFIG_SMP=y kernels, smp_call_function_single() returns -ENXIO when
invoked for a non-existent CPU. In contrast, in CONFIG_SMP=n kernels,
a splat is emitted and smp_call_function_single() otherwise silently
ignores its "cpu" argument, instead pretending that the caller intended
to have something happen on CPU 0. Given that there is now code that
expects smp_call_function_single() to return an error if a bad CPU was
specified, this difference in semantics needs to be addressed.
Bring the semantics of the CONFIG_SMP=n version of
smp_call_function_single() into alignment with its CONFIG_SMP=y
counterpart.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200205143409.GA7021@paulmck-ThinkPad-P72
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
It was requested to remove the cond_func check but the follow up patch was
overlooked. Remove it now.
Fixes: 67719ef25eeb ("smp: Add a smp_cond_func_t argument to smp_call_function_many()")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200127083915.434tdkztorkklpdu@linutronix.de
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes and improvements for the perf subsystem:
Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent an integer underflow in the perf mlock accounting
- Add a missing prototype for arch_perf_update_userpage()
Tooling:
- Add a missing unlock in the error path of maps__insert() in perf
maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the
sink configuration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command"
* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf maps: Add missing unlock to maps__insert() error case
perf probe: Add ustring support for perf probe command
perf: Make perf able to build with latest libbfd
perf test: Fix test case Merge cpu map
perf parse: Copy string to perf_evsel_config_term
perf parse: Refactor 'struct perf_evsel_config_term'
kernel/events: Add a missing prototype for arch_perf_update_userpage()
perf/cgroups: Install cgroup events to correct cpuctx
perf/core: Fix mlock accounting in perf_mmap()
|
| | |\ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf maps:
Cengiz Can:
- Add missing unlock to maps__insert() error case.
srcline:
Changbin Du:
- Make perf able to build with latest libbfd.
perf parse:
Leo Yan:
- Keep copy of string in perf_evsel_config_term() to fix sink terms
processing in ARM CoreSight.
perf test:
Thomas Richter:
- Fix test case Merge cpu map, removing extra reference count drop that
causes a segfault on s/390.
perf probe:
Thomas Richter:
- Add ustring support for perf probe command
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
`tools/perf/util/map.c` has a function named `maps__insert` that
acquires a write lock if its in multithread context.
Even though this lock is released when function successfully completes,
there's a branch that is executed when `maps_by_name == NULL` that
returns from this function without releasing the write lock.
Added an `up_write` to release the lock when this happens.
Fixes: a7c2b572e217 ("perf map_groups: Auto sort maps by name, if needed")
Signed-off-by: Cengiz Can <cengiz@kernel.wtf>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/20200120141553.23934-1-cengiz@kernel.wtf
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Kernel commit 88903c464321 ("tracing/probe: Add ustring type for user-space string")
adds support for user-space strings when type 'ustring' is specified.
Here is an example using sysfs command line interface
for kprobes:
Function to probe:
struct filename *
getname_flags(const char __user *filename, int flags, int *empty)
Setup:
# cd /sys/kernel/debug/tracing/
# echo 'p:tmr1 getname_flags +0(%r2):ustring' > kprobe_events
# cat events/kprobes/tmr1/format | fgrep print
print fmt: "(%lx) arg1=\"%s\"", REC->__probe_ip, REC->arg1
# echo 1 > events/kprobes/tmr1/enable
# touch /tmp/111
# echo 0 > events/kprobes/tmr1/enable
# cat trace|fgrep /tmp/111
touch-5846 [005] d..2 255520.717960: tmr1:\
(getname_flags+0x0/0x400) arg1="/tmp/111"
Doing the same with the perf tool fails.
Using type 'string' succeeds:
# perf probe "vfs_getname=getname_flags:72 pathname=filename:string"
Added new event:
probe:vfs_getname (on getname_flags:72 with pathname=filename:string)
....
# perf probe -d probe:vfs_getname
Removed event: probe:vfs_getname
However using type 'ustring' fails (output before):
# perf probe "vfs_getname=getname_flags:72 pathname=filename:ustring"
Failed to write event: Invalid argument
Error: Failed to add events.
#
Fix this by adding type 'ustring' in function
convert_variable_type().
Using ustring succeeds (output after):
# ./perf probe "vfs_getname=getname_flags:72 pathname=filename:ustring"
Added new event:
probe:vfs_getname (on getname_flags:72 with pathname=filename:ustring)
You can now use it in all perf tools, such as:
perf record -e probe:vfs_getname -aR sleep 1
#
Note: This issue also exists on x86, it is not s390 specific.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: sumanthk@linux.ibm.com
Link: http://lore.kernel.org/lkml/20200120132011.64698-2-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
libbfd has changed the bfd_section_* macros to inline functions
bfd_section_<field> since 2019-09-18. See below two commits:
o http://www.sourceware.org/ml/gdb-cvs/2019-09/msg00064.html
o https://www.sourceware.org/ml/gdb-cvs/2019-09/msg00072.html
This fix make perf able to build with both old and new libbfd.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200128152938.31413-1-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Commit a2408a70368a ("perf evlist: Maintain evlist->all_cpus")
introduces a test case for cpumap merge operation, see functions
perf_cpu_map__merge() and test__cpu_map_merge().
The test case fails on s390 with this error message:
[root@m35lp76 perf]# ./perf test -Fvvvvv 52
52: Merge cpu map :
--- start ---
cpumask list: 1-2,4-5,7
perf: /root/linux/tools/include/linux/refcount.h:131:\
refcount_sub_and_test: Assertion `!(new > val)' failed.
Aborted (core dumped)
[root@m35lp76 perf]#
The root cause is in the function test__cpu_map_merge():
It creates two cpu_maps named 'a' and 'b':
struct perf_cpu_map *a = perf_cpu_map__new("4,2,1");
struct perf_cpu_map *b = perf_cpu_map__new("4,5,7");
and creates a third map named 'c' which is the result of
the merge of maps a and b:
struct perf_cpu_map *c = perf_cpu_map__merge(a, b);
After some verifaction of the merged cpu_map all three
of them are have their reference count reduced and are
freed:
perf_cpu_map__put(a); (1)
perf_cpu_map__put(b);
perf_cpu_map__put(c);
The release of perf_cpu_map__put(a) is wrong. The map
is already released and free'ed as part of the function
perf_cpu_map__merge(struct perf_cpu_map *orig,
| struct perf_cpu_map *other)
+--> perf_cpu_map__put(orig);
|
+--> cpu_map__delete(orig)
At the end perf_cpu_map_put() is called for map 'orig'
alias 'a' and since the reference count is 1, the map
is deleted, as can be seen by the following gdb trace:
(gdb) where
#0 tcache_put (tc_idx=0, chunk=0x156cc30) at malloc.c:2940
#1 _int_free (av=0x3fffd49ee80 <main_arena>, p=0x156cc30,
have_lock=<optimized out>) at malloc.c:4222
#2 0x00000000012d5e78 in cpu_map__delete (map=0x156cc40) at cpumap.c:31
#3 0x00000000012d5f7a in perf_cpu_map__put (map=0x156cc40) at cpumap.c:45
#4 0x00000000012d723a in perf_cpu_map__merge (orig=0x156cc40,
other=0x156cc60) at cpumap.c:343
#5 0x000000000110cdd0 in test__cpu_map_merge (
test=0x14ea6c8 <generic_tests+2856>, subtest=-1) at tests/cpumap.c:128
Thus the perf_cpu_map__put(a) (see (1) above) frees map 'a'
a second time and causes the failure. Fix this be removing that
function call.
Output after:
[root@m35lp76 perf]# ./perf test -Fvvvvv 52
52: Merge cpu map :
--- start ---
cpumask list: 1-2,4-5,7
---- end ----
Merge cpu map: Ok
[root@m35lp76 perf]#
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: sumanthk@linux.ibm.com
Link: http://lore.kernel.org/lkml/20200120132011.64698-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
