summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* net: arp_ioctl() must hold RTNLEric Dumazet2011-01-242-7/+7
| | | | | | | | | | | | | | Commit 941666c2e3e0 "net: RCU conversion of dev_getbyhwaddr() and arp_ioctl()" introduced a regression, reported by Jamie Heilman. "arp -Ds 192.168.2.41 eth0 pub" triggered the ASSERT_RTNL() assert in pneigh_lookup() Removing RTNL requirement from arp_ioctl() was a mistake, just revert that part. Reported-by: Jamie Heilman <jamie@audible.transient.net> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: add driver for Softing cardKurt Van Dijck2011-01-223-0/+374
| | | | | | | | | | | | | This patch adds the driver that creates a platform:softing device from a pcmcia_device Note: the Kconfig indicates a dependency on the softing.ko driver, but this is purely to make configuration intuitive. This driver will work independent, but no CAN network devices appear until softing.ko is loaded too. Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* can: add driver for Softing cardKurt Van Dijck2011-01-228-0/+1815
| | | | | | | | | | This patch adds a driver for the platform:softing device. This will create (up to) 2 CAN network devices from 1 platform:softing device Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* atm: idt77105: fix fetch_stats() resultVasiliy Kulikov2011-01-221-1/+1
| | | | | | | | | copy_to_user() used PRIV(dev)->stats instead of local stats variable. Zero stats were returned to user in case of (zero != 0), also memcpy() was pointless. Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net_sched: accurate bytes/packets stats/ratesEric Dumazet2011-01-2114-33/+29
| | | | | | | | | | | | | | | | | | | In commit 44b8288308ac9d (net_sched: pfifo_head_drop problem), we fixed a problem with pfifo_head drops that incorrectly decreased sch->bstats.bytes and sch->bstats.packets Several qdiscs (CHOKe, SFQ, pfifo_head, ...) are able to drop a previously enqueued packet, and bstats cannot be changed, so bstats/rates are not accurate (over estimated) This patch changes the qdisc_bstats updates to be done at dequeue() time instead of enqueue() time. bstats counters no longer account for dropped frames, and rates are more correct, since enqueue() bursts dont have effect on dequeue() rate. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: Ensure that we unshare skbs prior to calling pskb_may_pullNeil Horman2011-01-213-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recently reported oops: kernel BUG at net/core/skbuff.c:813! invalid opcode: 0000 [#1] SMP last sysfs file: /sys/devices/virtual/net/bond0/broadcast CPU 8 Modules linked in: sit tunnel4 cpufreq_ondemand acpi_cpufreq freq_table bonding ipv6 dm_mirror dm_region_hash dm_log cdc_ether usbnet mii serio_raw i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma i7core_edac edac_core bnx2 ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase scsi_transport_sas dm_mod [last unloaded: microcode] Modules linked in: sit tunnel4 cpufreq_ondemand acpi_cpufreq freq_table bonding ipv6 dm_mirror dm_region_hash dm_log cdc_ether usbnet mii serio_raw i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma i7core_edac edac_core bnx2 ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase scsi_transport_sas dm_mod [last unloaded: microcode] Pid: 0, comm: swapper Not tainted 2.6.32-71.el6.x86_64 #1 BladeCenter HS22 -[7870AC1]- RIP: 0010:[<ffffffff81405b16>] [<ffffffff81405b16>] pskb_expand_head+0x36/0x1e0 RSP: 0018:ffff880028303b70 EFLAGS: 00010202 RAX: 0000000000000002 RBX: ffff880c6458ec80 RCX: 0000000000000020 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880c6458ec80 RBP: ffff880028303bc0 R08: ffffffff818a6180 R09: ffff880c6458ed64 R10: ffff880c622b36c0 R11: 0000000000000400 R12: 0000000000000000 R13: 0000000000000180 R14: ffff880c622b3000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff880028300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00000038653452a4 CR3: 0000000001001000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process swapper (pid: 0, threadinfo ffff8806649c2000, task ffff880c64f16ab0) Stack: ffff880028303bc0 ffffffff8104fff9 000000000000001c 0000000100000000 <0> ffff880000047d80 ffff880c6458ec80 000000000000001c ffff880c6223da00 <0> ffff880c622b3000 0000000000000000 ffff880028303c10 ffffffff81407f7a Call Trace: <IRQ> [<ffffffff8104fff9>] ? __wake_up_common+0x59/0x90 [<ffffffff81407f7a>] __pskb_pull_tail+0x2aa/0x360 [<ffffffffa0244530>] bond_arp_rcv+0x2c0/0x2e0 [bonding] [<ffffffff814a0857>] ? packet_rcv+0x377/0x440 [<ffffffff8140f21b>] netif_receive_skb+0x2db/0x670 [<ffffffff8140f788>] napi_skb_finish+0x58/0x70 [<ffffffff8140fc89>] napi_gro_receive+0x39/0x50 [<ffffffffa01286eb>] ixgbe_clean_rx_irq+0x35b/0x900 [ixgbe] [<ffffffffa01290f6>] ixgbe_clean_rxtx_many+0x136/0x240 [ixgbe] [<ffffffff8140fe53>] net_rx_action+0x103/0x210 [<ffffffff81073bd7>] __do_softirq+0xb7/0x1e0 [<ffffffff810d8740>] ? handle_IRQ_event+0x60/0x170 [<ffffffff810142cc>] call_softirq+0x1c/0x30 [<ffffffff81015f35>] do_softirq+0x65/0xa0 [<ffffffff810739d5>] irq_exit+0x85/0x90 [<ffffffff814cf915>] do_IRQ+0x75/0xf0 [<ffffffff81013ad3>] ret_from_intr+0x0/0x11 <EOI> [<ffffffff8101bc01>] ? mwait_idle+0x71/0xd0 [<ffffffff814cd80a>] ? atomic_notifier_call_chain+0x1a/0x20 [<ffffffff81011e96>] cpu_idle+0xb6/0x110 [<ffffffff814c17c8>] start_secondary+0x1fc/0x23f Resulted from bonding driver registering packet handlers via dev_add_pack and then trying to call pskb_may_pull. If another packet handler (like for AF_PACKET sockets) gets called first, the delivered skb will have a user count > 1, which causes pskb_may_pull to BUG halt when it does its skb_shared check. Fix this by calling skb_share_check prior to the may_pull call sites in the bonding driver to clone the skb when needed. Tested by myself and the reported successfully. Signed-off-by: Neil Horman CC: Andy Gospodarek <andy@greyhouse.net> CC: Jay Vosburgh <fubar@us.ibm.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* cxgb4: fix reported state of interfaces without linkDimitris Michailidis2011-01-211-1/+2
| | | | | | | | | | | Currently tools like ip and ifconfig report incorrect state for cxgb4 interfaces that are up but do not have link and do so until first link establishment. This is because the initial netif_carrier_off call is before register_netdev and it needs to be after to be fully effective. Fix this by moving netif_carrier_off into .ndo_open. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sctp: user perfect name for Delayed SACK Timer optionShan Wei2011-01-202-2/+3
| | | | | | | | | | | | | | | | | The option name of Delayed SACK Timer should be SCTP_DELAYED_SACK, not SCTP_DELAYED_ACK. Left SCTP_DELAYED_ACK be concomitant with SCTP_DELAYED_SACK, for making compatibility with existing applications. Reference: 8.1.19. Get or Set Delayed SACK Timer (SCTP_DELAYED_SACK) （http://tools.ietf.org/html/draft-ietf-tsvwg-sctpsocket-25) Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fix can_checksum_protocol() arguments swapEric Dumazet2011-01-191-1/+1
| | | | | | | | | | | | | | commit 0363466866d901fbc (net offloading: Convert checksums to use centrally computed features.) mistakenly swapped can_checksum_protocol() arguments. This broke IPv6 on bnx2 for instance, on NIC without TCPv6 checksum offloads. Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Revert "netlink: test for all flags of the NLM_F_DUMP composite"David S. Miller2011-01-195-6/+6
| | | | | | | | This reverts commit 0ab03c2b1478f2438d2c80204f7fef65b1bca9cf. It breaks several things including the avahi daemon. Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Fix misleading indentation in startup_gfar()Anton Vorontsov2011-01-191-1/+1
| | | | | | | | | Just stumbled upon the issue while looking for another bug. The code looks correct, the indentation is not. Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/irda/sh_irda: return to RX mode when TX errorKuninori Morimoto2011-01-191-2/+12
| | | | | | | | | sh_irda can not use RX/TX in same time, but this driver didn't return to RX mode when TX error occurred. This patch care xmit error case to solve this issue. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.Jesse Gross2011-01-191-2/+2
| | | | | | | | | | | In netif_skb_features() we return only the features that are valid for vlans if we have a vlan packet. However, we should not mask out NETIF_F_HW_VLAN_TX since it enables transmission of vlan tags and is obviously valid. Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* USB CDC NCM: tx_fixup() race condition fixAlexey Orishko2011-01-191-7/+12
| | | | | | | | | | - tx_fixup() can be called from either timer callback or from xmit() in usbnet, so spinlock is added to avoid concurrency-related problem. - minor correction due to checkpatch warning for some line over 80 chars after previous patch was applied. Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ns83820: Avoid bad pointer deref in ns83820_init_one().Jesper Juhl2011-01-191-3/+2
| | | | | | | | | | | | | | | | | In drivers/net/ns83820.c::ns83820_init_one() we dynamically allocate memory via alloc_etherdev(). We then call PRIV() on the returned storage which is 'return netdev_priv()'. netdev_priv() takes the pointer it is passed and adds 'ALIGN(sizeof(struct net_device), NETDEV_ALIGN)' to it and returns it. Then we test the resulting pointer for NULL, which it is unlikely to be at this point, and later dereference it. This will go bad if alloc_etherdev() actually returned NULL. This patch reworks the code slightly so that we test for a NULL pointer (and return -ENOMEM) directly after calling alloc_etherdev(). Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: Silence privacy extensions initializationRomain Francoise2011-01-191-3/+0
| | | | | | | | | | | | | | | | | | When a network namespace is created (via CLONE_NEWNET), the loopback interface is automatically added to the new namespace, triggering a printk in ipv6_add_dev() if CONFIG_IPV6_PRIVACY is set. This is problematic for applications which use CLONE_NEWNET as part of a sandbox, like Chromium's suid sandbox or recent versions of vsftpd. On a busy machine, it can lead to thousands of useless "lo: Disabled Privacy Extensions" messages appearing in dmesg. It's easy enough to check the status of privacy extensions via the use_tempaddr sysctl, so just removing the printk seems like the most sensible solution. Signed-off-by: Romain Francoise <romain@orebokech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Update bnx2x version to 1.62.00-4Yaniv Rosner2011-01-191-2/+2
| | | | | | | | Update bnx2x version to 1.62.00-4 Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Fix AER setting for BCM57712Yaniv Rosner2011-01-191-1/+1
| | | | | | | | Fix AER settings for BCM57712 to allow accessing all device addresses range in CL45 MDC/MDIO Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Fix BCM84823 LED behaviorYaniv Rosner2011-01-192-1/+21
| | | | | | | | Fix BCM84823 LED behavior which may show on some systems Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Mark full duplex on some external PHYsYaniv Rosner2011-01-191-1/+8
| | | | | | | | Device may show incorrect duplex mode for devices with external PHY Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Fix BCM8073/BCM8727 microcode loadingYaniv Rosner2011-01-191-30/+43
| | | | | | | | Improve microcode loading verification before proceeding to next stage Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: LED fix for BCM8727 over BCM57712Yaniv Rosner2011-01-191-1/+17
| | | | | | | | LED on BCM57712+BCM8727 systems requires different settings Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Common init will be executed only once after PORYaniv Rosner2011-01-191-0/+11
| | | | | | | | | Common init used to be called by the driver when the first port comes up, mainly to reset and reload external PHY microcode. However, in case management driver is active on the other port, traffic would halted. So limit the common init to be done only once after POR. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Swap BCM8073 PHY polarity if requiredYaniv Rosner2011-01-192-0/+46
| | | | | | | | Enable controlling BCM8073 PN polarity swap through nvm configuration, which is required in certain systems Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2011-01-1812-24/+36
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
| * iwlwifi: fix valid chain reading from EEPROMWey-Yi Guy2011-01-181-1/+1
| | | | | | | | | | | | | | | | | | | | When read valid tx/rx chains from EEPROM, there is a bug to use the tx chain value for both tx and rx, the result of this cause low receive throughput on 1x2 devices becuase rx will only utilize single chain instead of two chains Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath5k: fix locking in tx_complete_poll_workBob Copeland2011-01-181-0/+4
| | | | | | | | | | | | | | | | | | ath5k_reset must be called with sc->lock. Since the tx queue watchdog runs in a workqueue and accesses sc, it's appropriate to just take the lock over the whole function. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k_hw: do PA offset calibration only on longcal intervalRajkumar Manoharan2011-01-171-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The power detector adc offset calibration has to be done on 4 minutes interval (longcal * pa_skip_count). But the commit "ath9k_hw: fix a noise floor calibration related race condition" makes the PA calibration executed more frequently beased on nfcal_pending value. Running PAOffset calibration lesser than longcal interval doesn't help anything and the worse part is that it causes NF load timeouts and RX deaf conditions. In a very noisy environment, where the distance b/w AP & station is ~10 meter and running a downlink udp traffic with frequent background scan causes "Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state. This issue was originaly reported in Android platform where the network-manager application does bgscan more frequently on AR9271 chips. (AR9285 family usb device). Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k_htc: Fix endian issue in tx headerRajkumar Manoharan2011-01-172-4/+6
| | | | | | | | | | Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k_hw: ASPM interoperability fix for AR9380/AR9382Luis R. Rodriguez2011-01-172-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is an interoperability with AR9382/AR9380 in L1 state with a few root complexes which can cause a hang. This is fixed by setting some work around bits on the PCIE PHY. We fix by using a new ini array to modify these bits when the radio is idle. Cc: stable@kernel.org Cc: Jack Lee <jack.lee@atheros.com> Cc: Carl Huang <carl.huang@atheros.com> Cc: David Quan <david.quan@atheros.com> Cc: Nael Atallah <nael.atallah@atheros.com> Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: use maximum number of AMPDU frames as default in BA RXLuciano Coelho2011-01-131-9/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the buffer size is set to zero in the block ack parameter set field, we should use the maximum supported number of subframes. The existing code was bogus and was doing some unnecessary calculations that lead to wrong values. Thanks Johannes for helping me figure this one out. Cc: stable@kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luciano Coelho <coelho@ti.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: fix lockdep warningJohannes Berg2011-01-131-1/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the introduction of the fixes for the reorder timer, mac80211 will cause lockdep warnings because lockdep confuses local->skb_queue and local->rx_skb_queue and treats their lock as the same. However, their locks are different, and are valid in different contexts (the former is used in IRQ context, the latter in BH only) and the only thing to be done is mark the former as a different lock class so that lockdep can tell the difference. Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Sujith <m.sujith@gmail.com> Reported-by: Miles Lane <miles.lane@gmail.com> Tested-by: Sujith <m.sujith@gmail.com> Tested-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ieee80211: correct IEEE80211_ADDBA_PARAM_BUF_SIZE_MASK macroAmitkumar Karwar2011-01-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | It is defined in include/linux/ieee80211.h. As per IEEE spec. bit6 to bit15 in block ack parameter represents buffer size. So the bitmask should be 0xFFC0. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Cc: stable@kernel.org Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rt2x00: Don't leak mem in error path of rt2x00lib_request_firmware()Jesper Juhl2011-01-131-0/+1
| | | | | | | | | | | | | | | | | | We need to release_firmware() in order not to leak memory. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwmc3200wifi: Return proper error for iwm_if_allocAxel Lin2011-01-131-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | In the case of alloc_netdev_mq failure and kmalloc failure, current implementation returns ERR_PTR(0). As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR macro. Fix it by setting proper error code for ret variable in the failure cases. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | vmxnet3: Dont allocate extra MSI-x vectorsShreyas Bhatewara2011-01-162-5/+5
| | | | | | | | | | | | | | | | In case of single tx and rx queues, three MSI-x vectors are allocated instead of two. This patch fixes that. Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | vmxnet3: Add locking for access to command registerShreyas Bhatewara2011-01-163-0/+54
| | | | | | | | | | | | | | | | | | Access to cmd register is racey, especially in smp environments. Protect it using a spinlock. Signed-off-by: Matthieu Bucchianeri <matthieu@vmware.com> Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | vmxnet3: Disable napi in suspend, reenable in resume.Shreyas Bhatewara2011-01-161-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | There is a small possibility of a race where the suspend routine gets called, while a napi callback is still pending and when that comes up, it enables interrupts which just got disabled in the suspend routine. This change adds napi disable call in suspend and enable in resume to avoid race. Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Acked-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | vmxnet3: Make ethtool handlers multiqueue awareShreyas Bhatewara2011-01-161-114/+145
| | | | | | | | | | | | | | | | Show per-queue stats in ethtool -S output for vmxnet3 interface. Register dump of ethtool should dump registers for all tx and rx queues. Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | vmxnet3: Provide required number of bytes in first SG bufferShreyas Bhatewara2011-01-161-14/+9
| | | | | | | | | | | | | | | | | | | | This is a performance enhancement fix. vmxnet3 device performs better when provided with at least 54 bytes (ethernet 14 + IP 20+ TCP 20) in the first SG buffer. For UDP packets driver provides lesser than that in first sg. This change fixes the same. Also avoid the redundant pskb_may_pull() call. Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | vmxnet3: Enable HW Rx VLAN stripping by defaultShreyas Bhatewara2011-01-161-13/+1
| | | | | | | | | | | | | | | | | | Make hw vlan tag stripping as enabled by default. Thereby remove the code to conditionally enable it later. Signed-off-by: Guolin Yang <gyang@vmware.com> Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | vmxnet3: Preserve the MAC address configured by ifconfigShreyas Bhatewara2011-01-161-0/+5
| | | | | | | | | | | | | | | | While activating the device get it's MAC address from netdev. This will allow the MAC address configured using ifconfig to persist through the reset. Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | vmxnet3: fix ring size updateShreyas Bhatewara2011-01-161-1/+1
| | | | | | | | | | | | | | | | Fix a bug while changing ring size when MTU is changed. Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Acked-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | caif: checking the wrong variableDan Carpenter2011-01-161-4/+5
| | | | | | | | | | | | | | | | | | | | | | In the original code we check if (servl == NULL) twice. The first time should print the message that cfmuxl_remove_uplayer() failed and set "ret" correctly, but instead it just returns success. The second check should be checking the value of "ret" instead of "servl". Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | can: test size of struct sockaddr in sendmsgKurt Van Dijck2011-01-162-0/+6
| | | | | | | | | | | | | | | | This patch makes the CAN socket code conform to the manpage of sendmsg. Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'for-david' of git://git.open-mesh.org/ecsv/linux-mergeDavid S. Miller2011-01-164-14/+16
|\ \
| * | batman-adv: Use "__attribute__" shortcut macrosSven Eckelmann2011-01-163-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linux 2.6.21 defines different macros for __attribute__ which are also used inside batman-adv. The next version of checkpatch.pl warns about the usage of __attribute__((packed))). Linux 2.6.33 defines an extra macro __always_unused which is used to assist source code analyzers and can be used to removed the last existing __attribute__ inside the source code. Signed-off-by: Sven Eckelmann <sven@narfation.org>
| * | batman-adv: Even Batman should not dereference NULL pointersJesper Juhl2011-01-131-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There's a problem in net/batman-adv/unicast.c::frag_send_skb(). dev_alloc_skb() allocates memory and may fail, thus returning NULL. If this happens we'll pass a NULL pointer on to skb_split() which in turn hands it to skb_split_inside_header() from where it gets passed to skb_put() that lets skb_tail_pointer() play with it and that function dereferences it. And thus the bat dies. While I was at it I also moved the call to dev_alloc_skb() above the assignment to 'unicast_packet' since there's no reason to do that assignment if the memory allocation fails. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* | | qeth: l3 hw tx csum circumvent hw bugFrank Blaschka2011-01-161-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | Some OSA level have a bug in the hw tx csum logic. We can circumvent this bug by turning on IP hw csum also. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | qeth: postpone open till recovery is finishedUrsula Braun2011-01-162-4/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The open function of qeth is not executed if the qeth device is in state DOWN or HARDSETUP. A recovery switches from state SOFTSETUP to HARDSETUP to DOWN to HARDSETUP and back to SOFTSETUP. If open and recover are running concurrently, open fails if it hits the states HARDSETUP or DOWN. This patch inserts waiting for recovery finish in the qeth open functions to enable successful qeth device opening in spite of a running recovery. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-20 19:33:57 +0100