summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: Shortcut minstrel_ht rate setup for non-MRR capable devicesHelmut Schaa2011-03-141-7/+34
| | | | | | | | | | | | | Devices without multi rate retry support won't be able to use all rates as specified by mintrel_ht. Hence, we can simply skip setting up further rates as the devices will only use the first one. Also add a special case for devices with only two possible tx rates. We use sample_rate -> max_prob_rate for sampling and max_tp_rate -> max_prob_rate by default. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath5k: implement ieee80211_ops->{get,set}_ringparamJohn W. Linville2011-03-113-1/+46
| | | | | | set_ringparam only allows changes to tx ring at this time. Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: implement support for cfg80211_ops->{get,set}_ringparamJohn W. Linville2011-03-114-0/+102
| | | | Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: add support for ethtool_ops->{get,set}_ringparamJohn W. Linville2011-03-112-0/+41
| | | | Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlagn: support off-channel TXJohannes Berg2011-03-116-51/+238
| | | | | | | | | | | | Add support to iwlagn for off-channel TX. The microcode API for this is a bit strange in that it uses a hacked-up scan command, so the scan code needs to change quite a bit to accomodate that and be able to send it out. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: do not enable ps if 802.1x controlled port is unblockedJason Young2011-03-112-5/+36
| | | | | | | | | | | | | | | | If dynamic_ps is disabled, enabling power save before the 4-way handshake completes may delay the station from being authorized to send/receive traffic, i.e. increase roaming times. It also may result in a failed 4-way handshake depending on the AP's timing requirements and beacon interval, and the station's listen interval. To fix this, prevent power save from being enabled while the station isn't authorized and recalculate power save whenever the station's authorized state changes. Signed-off-by: Jason Young <a.young.jason@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* libertas: fix write past end of array in mesh_id_get()Dan Carpenter2011-03-111-7/+4
| | | | | | | | | | | | | | | defs.meshie.val.mesh_id is 32 chars long. It's not supposed to be NUL terminated. This code puts a terminator on the end to make it easier to print to sysfs. The problem is that if the mesh_id fills the entire buffer the original code puts the terminator one spot past the end. The way the original code was written, there was a check to make sure that maxlen was less than PAGE_SIZE. Since we know that maxlen is at most 34 chars, I just removed the check. Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Increase the wait count for nf load.Vivek Natarajan2011-03-111-2/+2
| | | | | | | | Increasing the wait count makes the nf load pass in most of the cases. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Fix PLL initialization for AR9485.Vivek Natarajan2011-03-111-2/+2
| | | | | | | | Increase the delay to make sure the initialization of pll passes. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Improve idle power consumption for AR9485.Vivek Natarajan2011-03-111-0/+2
| | | | | | | Set some GPIO pins to Pull-down mode to save power. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: remove support for the FIF_PROMISC_IN_BSS filter flagFelix Fietkau2011-03-111-3/+1
| | | | | | | | | | | | | | | | | | | | The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad and covers even frames with PHY errors. When this flag is enabled, this message shows up frequently during scanning or hardware resets: ath: Could not stop RX, we could be confusing the DMA engine when we start RX up Since promiscuous mode is usually not particularly useful, yet enabled by default by bridging (either used normally in 4-addr mode, or with hacks for various virtualization software), we should sacrifice it for better reliability during normal operation. This patch leaves it enabled if there are active monitor mode interfaces, since it's very useful for debugging. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: fix elp_work race conditionGrazvydas Ignotas2011-03-111-1/+3
| | | | | | | | | | | | | | | | | | While working on PS I've noticed elp_work is kicking rather often, and sometimes the chip is put to sleep before 5ms delay expires. This seems to happen because by the time wl1251_ps_elp_wakeup is called elp_work might still be pending. After wakeup is done, the processing may take some time, during which 5ms might expire and elp_work might get scheduled. In this case, ss soon as 1st thread finishes work and releases the mutex, elp_work will then put the device to sleep without 5ms delay. In addition 1st thread will queue additional elp_work needlessly. Fix this by cancelling work in wl1251_ps_elp_wakeup instead. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: remove wl1251_ps_set_elp functionGrazvydas Ignotas2011-03-111-34/+3
| | | | | | | | | | | | | wl1251_ps_set_elp() only does acx_sleep_auth call and takes the chip from/to ELP, however all callers of wl1251_ps_set_mode() have already taken the chip out of ELP and puts it back to ELP when they finish. This makes ELP calls (and register writes they result in) superfluous. So remove wl1251_ps_set_elp function and call acx_sleep_auth directly. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: update minstrel_ht sample rate when probe is setDaniel Halperin2011-03-091-10/+5
| | | | | | | | | Waiting until the status is received can cause the same rate to be probed multiple times consecutively. Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath5k: restrict AR5K_TX_QUEUE_ID_DATA_MAX to reflect the [0,3] rangeJohn W. Linville2011-03-091-1/+1
| | | | | | | This just matches reality... Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Bob Copeland <me@bobcopeland.com>
* net/wireless: add COUNTRY to to regulatory device ueventScott James Remnant2011-03-092-11/+29
| | | | | | | | | | | | | | | | | | | | | Regulatory devices issue change uevents to inform userspace of a need to call the crda tool; however these can often be sent before udevd is running, and were not previously included in the results of udevadm trigger (which requests a new change event using the /uevent attribute of the sysfs object). Add a uevent function to the device type which includes the COUNTRY information from the last request if it has yet to be processed, the case of multiple requests is already handled in the code by checking whether an unprocessed one is queued in the same manner and refusing to queue a new one. The existing udev rule continues to work as before. Signed-off-by: Scott James Remnant <keybuk@google.com> Acked-By: Kay Sievers <kay.sievers@vrfy.org> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ieee80211: add IEEE80211_COUNTRY_STRING_LEN definitionBing Zhao2011-03-096-7/+8
| | | | | | | and make use of it in wireless drivers Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: use kcalloc instead of kmalloc & memsetShan Wei2011-03-091-4/+2
| | | | | | | | | | Use kcalloc or kzalloc rather than the combination of kmalloc and memset. Thanks coccicheck for detecting this. (http://coccinelle.lip6.fr/) Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: fix scan race, simplify codeJohannes Berg2011-03-071-40/+24
| | | | | | | | | | | | | | | | | | The scan code has a race that Michael reported he ran into, but it's easy to fix while at the same time simplifying the code. The race resulted in the following warning: ------------[ cut here ]------------ WARNING: at net/mac80211/scan.c:310 ieee80211_rx_bss_free+0x20c/0x4b8 [mac80211]() Modules linked in: [...] [<c0033edc>] (unwind_backtrace+0x0/0xe0) from [<c004f2a4>] (warn_slowpath_common+0x4c/0x64) [... backtrace wasn't useful ...] Reported-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: trivial: update B43_PHY_N description (PHY support)Rafał Miłecki2011-03-071-1/+1
| | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* p54spi: Update kconfig help textMichael Buesch2011-03-071-3/+2
| | | | | | | | This updates the p54spi Kconfig help text. The driver works well on n8x0, so remove the words "experimental" and "untested". Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: Add log message to ieee80211_restart_hw()Michael Buesch2011-03-071-0/+3
| | | | | | | | | Add a log message to ieee80211_restart_hw() to highlight that special codepath in the logs. This helps debugging bugs in the rarely tested restart code. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix iwl-rx.c compilationStanislaw Gruszka2011-03-071-0/+1
| | | | | | | | | | My commit 466a19a003f3b45a755bc85f967c21da947f9a00 "iwlwifi: move rx handlers code to iwl-rx.c" breaks compilation on 32 bits. Fix that. Reported-by: Guy, Wey-Yi <wey-yi.w.guy@intel.com> Reported-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless:ath: use resource_size() help functionShan Wei2011-03-072-2/+2
| | | | | Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: remove unused macrosShan Wei2011-03-073-5/+0
| | | | | | | Compile test only. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath5k: Put hardware in PROMISC mode if there is more than 1 stations.Ben Greear2011-03-073-31/+53
| | | | | | | | | | It seems ath5k has issues receiving broadcast packets (ARPs) when using multiple STA interfaces associated with multiple APs. This patch ensures the NIC is always in PROMISC mode if there are more than 1 stations associated. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: avoid too frequent recover from statisticsStanislaw Gruszka2011-03-043-22/+30
| | | | | | | | | | | | | | | | | | | | | | | Usually H/W generate statistics notify once per about 100ms, but sometimes we can receive notify in shorter time, even 2 ms. This can be problem for plcp health and ack health checking. I.e. with 2 plcp errors happens randomly in 2 ms duration, we exceed plcp delta threshold equal to 100 (2*100/2). Also checking ack's in short time, can results not necessary false positive and firmware reset, for example when channel is noised and we do not receive ACKs frames or when remote device does not send ACKs at the moment. Patch change code to do statistic check and possible recovery only if 99ms elapsed from last check. Forced delay should assure we have good statistic data to estimate hardware state. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: cleanup iwl_good_plcp_healthStanislaw Gruszka2011-03-041-70/+45
| | | | | | | | Make iwl_good_plcp_health code easiest to read. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: move rx handlers code to iwl-rx.cStanislaw Gruszka2011-03-046-528/+500
| | | | | | | | | | | Put generic rx_handlers (except iwlagn_rx_reply_compressed_ba) to iwl-rx.c . Make functions static and change prefix from iwlagn_ to iwl_ . Beautify iwl_setup_rx_handlers and do some other minor coding style changes. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: Remove redundant preamble and RTS flag setup in minstrel_htHelmut Schaa2011-03-041-3/+1
| | | | | | | | | mac80211 does the same afterwards anyway. Hence, just drop this redundant code. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix txq memory address printing in debugfs.Ben Greear2011-03-041-4/+4
| | | | | | | | No use printing addresses of pointers, just print the pointers themselves. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Remove unused rt2x00queue_get_queue function.Gertjan van Wingerde2011-03-042-27/+0
| | | | | | | | | | | Now that all accesses to the data_queue structures is done via the specialized rt2x00queue_get_tx_queue function or via direct accesses, there is no need for the rt2x00queue_get_queue function anymore, so remove it. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Optimize getting the beacon queue structure.Gertjan van Wingerde2011-03-042-2/+2
| | | | | | | | | | | | In the spirit of optimizing the code to get the queue structure of TX queues, also optimize the code to get beacon queues. We can simply use the bcn queue field of the rt2x00_dev structure instead of using the rt2x00queue_get_queue function. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Include ATIM queue support in rt2x00queue_get_tx_queue.Gertjan van Wingerde2011-03-044-6/+9
| | | | | | | | | | | | | | | The ATIM queue is considered to be a TX queue by the drivers that support the queue. Therefore include support for the ATIM queue to the rt2x00queue_get_tx_queue function so that the drivers that support the ATIM queue can also use that function. Add the support in such a way that drivers that do not support the ATIM queue are not penalized in their efficiency. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Don't treat ATIM queue as second beacon queue.Gertjan van Wingerde2011-03-044-20/+16
| | | | | | | | | | | | Current code for the atim queue is strange, as it is considered in the rt2x00_dev structure as a second beacon queue. Normalize this by letting the atim queue have its own struct data_queue pointer in the rt2x00_dev structure. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix comment in rt2800pciHelmut Schaa2011-03-041-1/+1
| | | | | | | | We don't use interrupt threads anymore. Fix the comment. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Revise irqmask locking for PCI devicesHelmut Schaa2011-03-044-33/+22
| | | | | | | | | | | The PCI device irqmask is locked by a spin_lock. Currently spin_lock_irqsave is used everywhere. To reduce the locking overhead replace spin_lock_irqsave in hard irq context with spin_lock and in soft irq context with spin_lock_irq. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Remove now unused crypto.aid fieldHelmut Schaa2011-03-042-5/+2
| | | | | | Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix rt2800 key assignment in multi bssid setupsHelmut Schaa2011-03-041-13/+30
| | | | | | | | | | | | | | | | | | When setting up multiple BSSIDs in AP mode on an rt2800pci device we previously used the STAs AID to select an appropriate key slot. But since the AID is per VIF we can end up with two STAs having the same AID and thus using the same key index. This resulted in one STA overwriting the key information of another STA. Fix this by simply searching for the next unused entry in the pairwise key table. Also bring the key table init in sync with deleting keys by initializing the key table entries to 0 instead of 1. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Use an enum instead of u16 for the rate_mode TX descriptor fieldHelmut Schaa2011-03-041-1/+1
| | | | | | | | | This makes the code less error-prone. Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Don't call ieee80211_get_tx_rate for MCS ratesHelmut Schaa2011-03-042-15/+15
| | | | | | | | | | | | | ieee80211_get_tx_rate is not valid for HT rates. Hence, restructure the TX desciptor creation to be aware of MCS rates. The generic TX desciptor creation now cares about the rate_mode (CCK, OFDM, MCS, GF). As a result, ieee80211_get_tx_rate gets only called for legacy rates. Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Move TX descriptor field "ifs" into plcp substructHelmut Schaa2011-03-047-15/+17
| | | | | | | | | | "ifs" is only used by no-HT devices. Move it into the plcp substruct and fill in the value only for no-HT devices. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Optimize TX descriptor memory layoutIvo van Doorn2011-03-041-5/+5
| | | | | | | | | | Some fields only need to be u8 and for ifs and txop we can use the already available enums. Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Optimize TX descriptor handlingHelmut Schaa2011-03-0412-55/+79
| | | | | | | | | | | | | | | HT and no-HT rt2x00 devices use a partly different TX descriptor. Optimize the tx desciptor memory layout by putting the PLCP and HT substructs into a union and introduce a new driver flag to decide which TX desciptor format is used by the device. This saves us the expensive PLCP calculation fOr HT devices and the HT descriptor setup on no-HT devices. Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Generate sw sequence numbers only for devices that need itHelmut Schaa2011-03-045-4/+11
| | | | | | | | | | | | | | | Newer devices like rt2800* own a hardware sequence counter and thus don't need to use a software sequence counter at all. Add a new driver flag to shortcut the software sequence number generation on devices that don't need it. rt61pci, rt73usb and rt2800* seem to make use of a hw sequence counter while rt2400pci and rt2500* need to do it in software. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Use unlikely for unexpected error condition in rt2x00_mac_txHelmut Schaa2011-03-041-1/+1
| | | | | | | | rt2x00queue_write_tx_frame is unlikely to fail. Tell the compiler. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add unlikely macro to special case tx status handlingHelmut Schaa2011-03-041-1/+1
| | | | | | | | | | | This special case shouldn't happen very often. Only if a frame that is not intended to be aggregated ends up in an AMPDU _and_ was intended to be sent at a different MCS rate as the aggregate. Hence, using unlikely is justified. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Remove useless NULL checkHelmut Schaa2011-03-041-2/+1
| | | | | | | | | Since tx_info->control.vif was already accessed before it cant't be NULL here. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Make use of unlikely during tx status processingHelmut Schaa2011-03-041-2/+2
| | | | | | | | These conditions are unlikely to happen, tell the compiler. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Optimize calls to rt2x00queue_get_queueHelmut Schaa2011-03-046-8/+25
| | | | | | | | | | | | | | | | | In some cases (tx path for example) we don't need to check for non-tx queues in rt2x00queue_get_queue. Hence, introduce a new method rt2x00queue_get_tx_queue that is only valid for tx queues and use it in places where only tx queues are valid. Furthermore, this new method is quite short and as such can be inlined to avoid the function call overhead. This only converts the txdone functions of drivers that don't use an ATIM queue and the generic tx path. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-23 10:31:11 +0100