summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* net: Fix warning fallout from recent NAPI interface changes.David S. Miller2008-12-2711-14/+0
| | | | | | | | | | | When we removed the network device argument from several NAPI interfaces in 908a7a16b852ffd618a9127be8d62432182d81b4 ("net: Remove unused netdev arg from some NAPI interfaces.") several drivers now started getting unused variable warnings. This fixes those up. Signed-off-by: David S. Miller <davem@davemloft.net>
* gro: Fix potential use after freeHerbert Xu2008-12-261-1/+4
| | | | | | | | | | | | | The initial skb may have been freed after napi_gro_complete in napi_gro_receive if it was merged into an existing packet. Thus we cannot check same_flow (which indicates whether it was merged) after calling napi_gro_complete. This patch fixes this by saving the same_flow status before the call to napi_gro_complete. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: If AN is enabled, always read speed/duplex from the AN advertising bitsBen Hutchings2008-12-261-7/+10
| | | | | | | | | When AN is enabled and the link is down the speed/duplex control bits will not be meaningful. Use the advertising bits instead, and mask them with the LPA bits if and only if AN is complete (as before). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: When disabling the NIC, close the device rather than unregistering itBen Hutchings2008-12-261-24/+23
| | | | | | | | This should reduce user confusion and may also aid recovery (ioctls will still be available). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: SFT9001: Add cable diagnosticsBen Hutchings2008-12-261-8/+107
| | | | | | | | | | The SFT9001 firmware implements cable diagnostics; run those and include their results in a self-test. In case of a cable fault, do not fail the self-test as a whole; only faults in the NIC should cause that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for multiple PHY self-testsBen Hutchings2008-12-265-15/+44
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Merge top-level functions for self-testsBen Hutchings2008-12-263-55/+48
| | | | | | | Pass in ethtool test flags to determine which tests to run. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up PHY mode management in loopback self-testBen Hutchings2008-12-261-12/+7
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Fix unreliable link detection in some loopback modesBen Hutchings2008-12-263-13/+24
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Generate unique names for per-NIC workqueuesBen Hutchings2008-12-262-1/+6
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.3ad: use standard ethhdr instead of ad_headerHolger Eitzenberger2008-12-262-18/+8
| | | | | | | | | | | | 802.3ad has its own ethhdr-like structure in the form of an ad_header, which is at the start of both the LACPDU and marker PDU. Both are the same from the struct values, both are packed as well. It's therefore perfectly fine to replace the ad_header by the ethhdr and to remove its definition. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.3ad: generalize out mac address initializerHolger Eitzenberger2008-12-262-11/+14
| | | | | | | | | Generalize out mac address initializer for the LACPDU multicast address and use in two places. Remove the now unused AD_MULTICAST_LACPDU_ADDR. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.3ad: initialize ports LACPDU from const initializerHolger Eitzenberger2008-12-261-49/+12
| | | | | | | | Save some text by initializing ports LACPDU from const initializer, then get rid of ad_initialize_lacpdu(). Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.3ad: remove typedef around ad_systemHolger Eitzenberger2008-12-261-3/+3
| | | | | | | | As typedefs are considered a bad thing most of the time remove the typedef around ad_system. Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.3ad: turn ports is_individual into a boolHolger Eitzenberger2008-12-262-4/+4
| | | | | | | Turn ports is_individual into a bool. There is no functional change. Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.3ad: turn ports is_enabled into a boolHolger Eitzenberger2008-12-262-4/+5
| | | | | | | Turn ports is_enabled into a bool. There is no functional change. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.3ad: make ntt boolHolger Eitzenberger2008-12-262-11/+13
| | | | | | | | Turn Need-To-Transmit port variable into a bool. There is no functional change. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.Peter P Waskiewicz Jr2008-12-261-34/+30
| | | | | | | | | | | The adapter rings are kcalloc()'d, but in set_ringparam() in ixgbe_ethtool, we replace that memory from the vmalloc() pool. This can result in a NULL pointer reference when trying to modify the rings at a later time, or on device removal. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Fix NAPI enable/disable path when using DCBPeter P Waskiewicz Jr2008-12-262-5/+10
| | | | | | | | | This change allows DCB mode to change the number of queues, and presumably the number of NAPI instances, safely. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Init NAPI dev_list on napi_delPeter P Waskiewicz Jr2008-12-261-1/+1
| | | | | | | | | | | | | | | | | The recent GRO patches introduced the NAPI removal of devices in free_netdev. For drivers that can change the number of queues during driver operation, the NAPI infrastructure doesn't allow the freeing and re-addition of NAPI entities without reloading the driver. This change reinitializes the dev_list in each NAPI struct on delete, instead of just deleting it (and assigning the list pointers to POISON). Drivers that wish to remove/re-add NAPI will need to re-initialize the netdev napi_list after removing all NAPI instances, before re-adding NAPI devices again. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: re-order queues to support cleaner use of ivar on 82576Alexander Duyck2008-12-262-39/+79
| | | | | | | | | | | The 82576 adapter orders the queues in pairs when virtualization is in use. The queue ordering previously conflicted with the ordering when sr-iov was enabled. This new ordering allows a PF to allocate 2 queues without using any VF resources. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: defeature tx head writebackAlexander Duyck2008-12-263-52/+39
| | | | | | | | | | This patch removes tx head writeback as it was found to not provide a significant improvement in tx performance and on some systems has been seen to cause a performance degredation due to partial cache line writes. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipsec: Remove useless ret variableHerbert Xu2008-12-261-3/+1
| | | | | | | | This patch removes a useless ret variable from the IPv4 ESP/UDP decapsulation code. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* ucc_geth: Eliminate the need for forward referencesAnton Vorontsov2008-12-261-42/+39
| | | | | | | | | This patch simply reorders some functions to eliminate the need for forward references. No other changes than that. Suggested-by: Timur Tabi <timur@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* atm: Driver for Solos PCI ADSL2+ card.David Woodhouse2008-12-263-0/+797
| | | | | | | | | | This adds basic support for the 'Solos' PCI ADSL2+ cards being developed by Traverse Technologies and Xrio Ltd: http://www.traverse.com.au/productview.php?product_id=116 Signed-off-by: Nathan Williams <nathan@traverse.com.au> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gigaset: ifdef cleanupTilman Schmidt2008-12-264-82/+6
| | | | | | | Remove unnecessary #ifdef-s and #if-0-ed code sections. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
* gigaset: use pr_err() and pr_info()Tilman Schmidt2008-12-268-58/+51
| | | | | | | | | Switch from private printk wrapper macros to using pr_err() and pr_info() from linux/kernel.h, at the same time unifying a few error messages. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
* cxgb3: add control to access embedded imagesDivy Le Ray2008-12-262-0/+19
| | | | | | | | Update contol path between cxgb3 and ULP modules (iWARP, iSCSI) to provide access to firware and protocol engine info. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wireless/prism54: fix sparse warnings: make symbols staticHannes Eder2008-12-261-4/+4
| | | | | | | | | | | | Fix this sparse warnings: drivers/net/wireless/prism54/islpci_hotplug.c:97:1: warning: symbol 'prism54_probe' was not declared. Should it be static? drivers/net/wireless/prism54/islpci_hotplug.c:220:1: warning: symbol 'prism54_remove' was not declared. Should it be static? drivers/net/wireless/prism54/islpci_hotplug.c:263:1: warning: symbol 'prism54_suspend' was not declared. Should it be static? drivers/net/wireless/prism54/islpci_hotplug.c:286:1: warning: symbol 'prism54_resume' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wireless/ipw2x00: fix sparse warnings: make symbols staticHannes Eder2008-12-261-3/+3
| | | | | | | | | | | Fix this sparse warnings: drivers/net/wireless/ipw2x00/ipw2100.c:5271:6: warning: symbol 'ipw2100_queues_initialize' was not declared. Should it be static? drivers/net/wireless/ipw2x00/ipw2100.c:5278:6: warning: symbol 'ipw2100_queues_free' was not declared. Should it be static? drivers/net/wireless/ipw2x00/ipw2100.c:5285:5: warning: symbol 'ipw2100_queues_allocate' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wireless/b43: fix sparse warnings: make symbols staticHannes Eder2008-12-262-12/+12
| | | | | | | | | | | | | | | | | | Fix this sparse warnings: drivers/net/wireless/b43/phy_a.c:80:6: warning: symbol 'b43_radio_set_tx_iq' was not declared. Should it be static? drivers/net/wireless/b43/phy_a.c:150:6: warning: symbol 'b43_radio_init2060' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:57:10: warning: symbol 'b43_radio_channel_codes_bg' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:218:6: warning: symbol 'b43_set_txpower_g' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:386:6: warning: symbol 'b43_nrssi_hw_write' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:393:5: warning: symbol 'b43_nrssi_hw_read' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:404:6: warning: symbol 'b43_nrssi_hw_update' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:418:6: warning: symbol 'b43_nrssi_mem_update' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:592:6: warning: symbol 'b43_calc_nrssi_slope' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:1357:5: warning: symbol 'b43_radio_init2050' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wireless/ath9k: fix sparse warnings: make symbols staticHannes Eder2008-12-261-30/+32
| | | | | | | | | | | | | | | | | | | | Fix this sparse warnings: drivers/net/wireless/ath9k/eeprom.c:195:6: warning: symbol 'ath9k_fill_eeprom' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:463:5: warning: symbol 'ath9k_check_eeprom' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:1219:6: warning: symbol 'ath9k_hw_set_def_power_per_rate_table' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:1510:6: warning: symbol 'ath9k_hw_set_4k_power_per_rate_table' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2007:5: warning: symbol 'ath9k_set_txpower' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2106:6: warning: symbol 'ath9k_set_addac' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2543:6: warning: symbol 'ath9k_eeprom_set_board_values' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2606:5: warning: symbol 'ath9k_get_eeprom_antenna_cfg' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2622:4: warning: symbol 'ath9k_hw_get_4k_num_ant_config' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2628:4: warning: symbol 'ath9k_hw_get_def_num_ant_config' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2647:4: warning: symbol 'ath9k_get_num_ant_config' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2790:5: warning: symbol 'ath9k_get_eeprom' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wireless: fix sparse warnings: make symbols staticHannes Eder2008-12-263-3/+3
| | | | | | | | | | | Fix this sparse warnings: drivers/net/wireless/airo.c:3610:6: warning: symbol 'mpi_receive_802_11' was not declared. Should it be static? drivers/net/wireless/atmel.c:3183:6: warning: symbol 'atmel_join_bss' was not declared. Should it be static? drivers/net/wireless/ray_cs.c:831:5: warning: symbol 'ray_dev_init' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wan/z85230.c: fix sparse warnings: un-EXPORT symbolsHannes Eder2008-12-261-8/+2
| | | | | | | | | | | | | The symbols are only references within the translation unit they are defined in, so un-EXPORT them und make them 'static'. Fix this sparse warnings: drivers/net/wan/z85230.c:604:25: warning: symbol 'z8530_dma_sync' was not declared. Should it be static? drivers/net/wan/z85230.c:613:25: warning: symbol 'z8530_txdma_sync' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wan: fix sparse warning: make symbol staticHannes Eder2008-12-261-1/+1
| | | | | | | | | Fix this sparse warning: drivers/net/wan/x25_asy.c:623:5: warning: symbol 'x25_asy_esc' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/wan: fix sparse warnings: make do-while a compound statementHannes Eder2008-12-261-4/+4
| | | | | | | | | | Fix this sparse warnings: drivers/net/wan/wanxl.c:414:3: warning: do-while statement is not a compound statement drivers/net/wan/wanxl.c:441:3: warning: do-while statement is not a compound statement Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/tulip: fix sparse warnings: make do-while a compound statementHannes Eder2008-12-262-4/+4
| | | | | | | | | | Fix this sparse warnings: drivers/net/tulip/de2104x.c:1695:4: warning: do-while statement is not a compound statement drivers/net/tulip/tulip_core.c:1433:5: warning: do-while statement is not a compound statement Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/tokenring: fix sparse warnings: make symbols staticHannes Eder2008-12-264-5/+5
| | | | | | | | | | | | Fix this sparse warnings: drivers/net/tokenring/ibmtr.c:1840:6: warning: symbol 'tok_rerun' was not declared. Should it be static? drivers/net/tokenring/madgemc.c:469:16: warning: symbol 'madgemc_setnselout_pins' was not declared. Should it be static? drivers/net/tokenring/proteon.c:286:16: warning: symbol 'proteon_setnselout_pins' was not declared. Should it be static? drivers/net/tokenring/skisa.c:303:16: warning: symbol 'sk_isa_setnselout_pins' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/skfp: fix sparse warnings: make symbols staticHannes Eder2008-12-261-3/+3
| | | | | | | | | | | Fix this sparse warnings: drivers/net/skfp/skfddi.c:620:13: warning: symbol 'skfp_interrupt' was not declared. Should it be static? drivers/net/skfp/skfddi.c:687:25: warning: symbol 'skfp_ctl_get_stats' was not declared. Should it be static? drivers/net/skfp/skfddi.c:1232:6: warning: symbol 'CheckSourceAddress' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/qlge: fix sparse warnings: make symbols staticHannes Eder2008-12-262-2/+2
| | | | | | | | | | Fix this sparse warnings: drivers/net/qlge/qlge_ethtool.c:100:6: warning: symbol 'ql_update_stats' was not declared. Should it be static? drivers/net/qlge/qlge_mpi.c:22:5: warning: symbol 'ql_get_mb_sts' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/netxen: fix sparse warnings: use NULL pointer instead of plain ↵Hannes Eder2008-12-261-2/+2
| | | | | | | | | | | | integer Fix this sparse warnings: drivers/net/netxen/netxen_nic_hw.c:1462:18: warning: Using plain integer as NULL pointer drivers/net/netxen/netxen_nic_hw.c:1536:18: warning: Using plain integer as NULL pointer Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/ixgbe: fix sparse warnings: make symbols staticHannes Eder2008-12-262-14/+14
| | | | | | | | | | | | | | | | | Fix this sparse warnings: drivers/net/ixgbe/ixgbe_82598.c:180:5: warning: symbol 'ixgbe_get_copper_link_capabilities_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:245:5: warning: symbol 'ixgbe_setup_fc_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:729:5: warning: symbol 'ixgbe_set_vmdq_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:773:5: warning: symbol 'ixgbe_set_vfta_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:897:5: warning: symbol 'ixgbe_read_analog_reg8_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:919:5: warning: symbol 'ixgbe_write_analog_reg8_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:940:5: warning: symbol 'ixgbe_read_i2c_eeprom_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:1000:5: warning: symbol 'ixgbe_get_supported_physical_layer_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_dcb_82598.c:100:5: warning: symbol 'ixgbe_dcb_config_packet_buffers_82598' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/irda: fix sparse warnings: make symbols staticHannes Eder2008-12-263-11/+11
| | | | | | | | | | | | | | | | | | Fix this sparse warnings: drivers/net/irda/ma600-sir.c:239:5: warning: symbol 'ma600_reset' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:875:5: warning: symbol 'smsc_ircc_hard_xmit_sir' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:1131:6: warning: symbol 'smsc_ircc_set_sir_speed' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:1897:6: warning: symbol 'smsc_ircc_sir_start' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:150:5: warning: symbol 'w83977af_open' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:313:5: warning: symbol 'w83977af_probe' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:412:6: warning: symbol 'w83977af_change_speed' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:492:5: warning: symbol 'w83977af_hard_xmit' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:734:5: warning: symbol 'w83977af_dma_receive' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:806:5: warning: symbol 'w83977af_dma_receive_complete' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/igb: remove dead code (function 'igb_read_pci_cfg')Hannes Eder2008-12-261-7/+0
| | | | | | | | | | Fix this warning: drivers/net/igb/e1000_mac.c:54: warning: 'igb_read_pci_cfg' defined but not used Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/enic: fix sparse warning: make symbol staticHannes Eder2008-12-261-1/+1
| | | | | | | | | Fix this sparse warning: drivers/net/enic/vnic_dev.c:288:5: warning: symbol 'vnic_dev_capable' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/e1000e: fix sparse warnings: make symbols staticHannes Eder2008-12-261-2/+4
| | | | | | | | | | Fix this sparse warnings: drivers/net/e1000e/es2lan.c:1265:5: warning: symbol 'e1000_read_kmrn_reg_80003es2lan' was not declared. Should it be static? drivers/net/e1000e/es2lan.c:1298:5: warning: symbol 'e1000_write_kmrn_reg_80003es2lan' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/cxgb3: comment out dead codeHannes Eder2008-12-261-0/+2
| | | | | | | | | | | | | | The function 'vsc8211_set_speed_duplex' is not used, so comment it out. For 'vsc8211_set_automdi' the function 'vsc8211_set_speed_duplex' is the only caller, so comment it out as well. Fix this (sparse) warning: drivers/net/cxgb3/vsc8211.c:269: warning: 'vsc8211_set_automdi' defined but not used drivers/net/cxgb3/vsc8211.c:295:5: warning: symbol 'vsc8211_set_speed_duplex' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/bonding: fix sparse warnings: move decls to header fileHannes Eder2008-12-263-4/+5
| | | | | | | | | | | Fix this sparse warnings: drivers/net/bonding/bond_main.c:104:20: warning: symbol 'bonding_defaults' was not declared. Should it be static? drivers/net/bonding/bond_main.c:204:22: warning: symbol 'ad_select_tbl' was not declared. Should it be static? drivers/net/bonding/bond_sysfs.c:60:21: warning: symbol 'bonding_rwsem' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/atlx: fix sparse warnings: make symbols staticHannes Eder2008-12-261-2/+2
| | | | | | | | | | Fix this sparse warnings: drivers/net/atlx/atl1.c:198:16: warning: symbol 'atl1_check_options' was not declared. Should it be static? drivers/net/atlx/atl1.c:526:5: warning: symbol 'atl1_read_mac_addr' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/arcnet: fix sparse warnings: make symbols staticHannes Eder2008-12-262-2/+2
| | | | | | | | | | Fix this sparse warnings: drivers/net/arcnet/capmode.c:64:6: warning: symbol 'arcnet_cap_init' was not declared. Should it be static? drivers/net/arcnet/com90xx.c:586:5: warning: symbol 'com90xx_reset' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-30 13:01:46 +0100