summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* USB: OHCI: fix endless polling behaviorAlan Stern2008-10-171-19/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch (as1149) fixes an obscure problem in OHCI polling. In the current code, if the RHSC interrupt status flag turns on at a time when RHSC interrupts are disabled, it will remain on forever: The interrupt handler is the only place where RHSC status gets turned back off; The interrupt handler won't turn RHSC status off because it doesn't turn off status flags if the corresponding interrupt isn't enabled; RHSC interrupts will never get enabled because ohci_root_hub_state_changes() doesn't reenable RHSC if RHSC status is on! As a result we will continue polling indefinitely instead of reverting to interrupt-driven operation, and the root hub will not autosuspend. This particular sequence of events is not at all unusual; in fact plugging a USB device into an OHCI controller will usually cause it to occur. Of course, this is a bug. The proper thing to do is to turn off RHSC status just before reading the actual port status values. That way either a port status change will be detected (if it occurs before the status read) or it will turn RHSC back on. Possibly both, but that won't hurt anything. We can still check for systems in which RHSC is totally broken, by re-reading RHSC after clearing it and before reading the port statuses. (This re-read has to be done anyway, to post the earlier write.) If RHSC is on but no port-change statuses are set, then we know that RHSC is broken and we can avoid re-enabling it. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: option: add Pantech cardsDan Williams2008-10-171-0/+9
| | | | | | | | Add some Pantech mobile broadband IDs. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: hub.c: Add initial_descriptor_timeout module parameter for usbcoreJaroslav Kysela2008-10-172-1/+29
| | | | | | | | | | | | | | | | | | This patch adds initial_descriptor_timeout module parameter for usbcore.ko to allow modify initial 64-byte USB_REQ_GET_DESCRIPTOR timeout for non-standard devices. For example, the SATA8000 device from DATAST0R Technology Corp requires about 10 seconds to send reply (probably it waits until inserted disk is ready for operation). Also, this patch adds missing usbcore parameters to Documentation/kernel-parameters.txt. Signed-off-by: Jaroslav Kysela <perex@perex.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Export if an interface driver supports autosuspend.Sarah Sharp2008-10-172-0/+40
| | | | | | | | | | | | | | | Create a new sysfs file per interface named supports_autosuspend. This file returns true if an interface driver's .supports_autosuspend flag is set. It also returns true if the interface is unclaimed (since the USB core will autosuspend a device if an interface is not claimed). This new sysfs file will be useful for user space scripts to test whether a USB device correctly auto-suspends. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: fix remote-wakeup support for ARC/TDI coreAlan Stern2008-10-173-14/+29
| | | | | | | | | | | | | | | | | | This patch (as1147) fixes the remote-wakeup support for EHCI controllers using the ARC/TDI "embedded-TT" core. These controllers turn off the RESUME bit by themselves when a port resume is complete; hence we need to keep separate track of which ports are suspended or in the process of resuming. The patch also makes a couple of small improvements in ehci_irq(), replacing reads of the command register with the value already stored in a local variable. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Thomas Reitmayr <treitmayr@devbase.at> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: snoop processes opening usbfs device filesAlan Stern2008-10-171-0/+2
| | | | | | | | | | | This patch (as1148) adds a new "snoop" message to usbfs when a device file is opened, identifying the process responsible. This comes in extremely handy when trying to determine which program is doing some unwanted USB access. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Option / AnyData new modem, same IDJon K Hellan2008-10-171-1/+1
| | | | | | | | The AnyData ADU-310 series of wireless modems uses the same product ID as the ADU-E100 series. Signed-off-by: Jon K Hellan <hellan@acm.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: log a warning if ehci-hcd is not loaded firstAlan Stern2008-10-175-2/+29
| | | | | | | | | | | | This patch (as1139) adds a warning to the system log whenever ehci-hcd is loaded after ohci-hcd or uhci-hcd. Nowadays most distributions are pretty good about not doing this; maybe the warning will help convince anyone still doing it wrong. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> [2.6.27] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI, OHCI, UHCI: remove version numbersAlan Stern2008-10-176-19/+16
| | | | | | | | | | | This patch (as1145) removes the essentially useless driver-version strings from ehci-hcd, ohci-hcd, and uhci-hcd. It also unifies the form of the banner lines they display upon loading and adds a missing test for usb_disabled() to ehci-hcd. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: anchor API changes needed for btusbOliver Neukum2008-10-172-0/+73
| | | | | | | | | This extends the anchor API as btusb needs for autosuspend. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ftdi-elan: Always pass usb_bulk_msg() a timeout in milliseconds.Sarah Sharp2008-10-171-5/+5
| | | | | | | | | | | | | The kernel doc for usb_bulk_msg() says the timeout for a bulk message should be specified in milliseconds. The ftdi-elan driver converts milliseconds to jiffies before passing the timeout to usb_bulk_msg(). This is mostly harmless, since it will just lead to very long timeouts, but was obviously not the intent of the original author. Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com> Acked-by: Tony Olech <tony.olech@elandigitalsystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: isp1760: Use an IS_ERR test rather than a NULL testJulien Brunel2008-10-171-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In case of error, the function isp1760_register returns an ERR pointer, but never returns a NULL pointer. So after a call to this function, a NULL test should be replaced by an IS_ERR test. Moreover, we have noticed that: (1) the result of isp1760_register is assigned through the function pci_set_drvdata without an error test, (2) if the call to isp1760_register fails, the current function (isp1761_pci_probe) returns 0, and if it succeeds, it returns -ENOMEM, which seems odd. Thus, we suggest to move the test before the call to pci_set_drvdata to correct (1), and to turn it into a non IS_ERR test to correct (2). The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @bad_null_test@ expression x,E; statement S1, S2; @@ x = isp1760_register(...) ... when != x = E * if (x == NULL) S1 else S2 // </smpl> Signed-off-by: Julien Brunel <brunel@diku.dk> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: improve ehci_watchdog's side effect in CPU power managementYi Yang2008-10-171-5/+7
| | | | | | | | | | | | | | | | | | | | | | ehci_watchdog will wake up CPU very frequently so that CPU stays at C3 very short, average residence time is about 50 ms on Aspire One, but we expect it should be about 1 second or more, so this kind of periodic timer is very bad for power saving. We can't remove this timer because of some bad USB controller chipset, but at least we should reduce its side effect to as possible as low. This patch can make CPU stay at C3 longer, average residence time is about twice as long as original. Please consider to apply it, thanks Signed-off-by: Yi Yang <yi.y.yang@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: UHCI: improve scheduling of interrupt URBsAlan Stern2008-10-171-6/+11
| | | | | | | | | | | | | | | | | This patch (as1140) adds a little intelligence to the interrupt-URB scheduler in uhci-hcd. Right now the scheduler is stupid; every URB having the same period is assigned to the same slot. Thus a large group of period-N URBs can fill their slot and cause -ENOSPC errors even when all the lower-period slots are empty. With the patch, if an URB doesn't fit in its assigned slot then the scheduler will try using lower-period slots. This will provide greater flexibility. As an example, the driver will be able to handle more than just three or four mice, which the current driver cannot. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ti_usb_3410_5052: removed duplicated includeHuang Weiyi2008-10-171-1/+0
| | | | | | | | | Removed duplicated #include <linux/firmware.h> in drivers/usb/serial/ti_usb_3410_5052.c. Signed-off-by: Huang Weiyi <hwy@cn.fujitsu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: vstusb.c : new driver for spectrometers used by Vernier Software & ↵Stephen Ware2008-10-176-0/+857
| | | | | | | | | | | | | | | | Technology, Inc. This patch adds the vstusb driver to the drivers/usb/misc directory. This driver provides support for Vernier Software & Technology spectrometers, all made by Ocean Optics. The driver provides both IOCTL and read()/write() methods for sending raw data to spectrometers across the bulk channel. Each method allows for a configured timeout. From: Stephen Ware <stephen.ware@eqware.net> Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb gadget: cdc ethernet notification bugfixDavid Brownell2008-10-171-0/+7
| | | | | | | | | | | | | | | | Bugfix for the new CDC Ethernet code: as part of activating the network interface's USB link, make sure its link management code knows whether the interface is open or not. Without this fix, the link won't work right when it's brought up before the link is active ... because the initial notification it sends will have the wrong link state (down, not up). Makes it hard to bridge these links (on the host side), among other things. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: stable <stable@kernel.org> [2.6.27] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: omap_udc: sync with OMAP treeTony Lindgren2008-10-172-1/+8
| | | | | | | | | | | | | Sync up USB parts of the omap_udc support in mainline with the OMAP tree. This patch addresses some OMAP2 differences ... there's another, with respect to the double-buffering issue with PIO-IN in omap_ep_setup() (which is now out of sync with the comments), but it's not clear right now how to address that. From: Tony Lindgren <tony@atomide.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ohci-omap: handle other omap15xx chipsTony Lindgren2008-10-171-2/+2
| | | | | | | | | | | Sync up USB parts of the ohci-omap support in mainline with the OMAP tree. This patch supports another first generation OMAP1 part: not just the OMAP 1510 (and its catalog version, the OMAP 5910), but also OMAP 310. From: Tony Lindgren <tony@atomide.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: remove dead code from procfsFelipe Balbi2008-10-171-11/+21
| | | | | | | | | | | When removing the procfs file, I forgot to remove some code that created and removed that file. Here's a patch to fix it. Ideally this patch will be melded into the patch removing the procfs file, don't know if it's possible still. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: general cleanup to musbhsdma.cFelipe Balbi2008-10-171-151/+155
| | | | | | | | | Basically getting rid of CaMeLcAsE, but also adding missing lines and spaces. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb_hdrc build fixesDavid Brownell2008-10-175-29/+13
| | | | | | | | | | | | | | | | | | | | | | | | | Minor musb_hdrc updates: - so it'll build on DaVinci, given relevant platform updates; * remove support for an un-shipped OTG prototype * rely on gpiolib framework conversion for the I2C GPIOs * the <asm/arch/hdrc_cnf.h> mechanism has been removed - catch comments up to the recent removal of the per-SOC header with the silicon configuration data; - and remove two inappropriate "inline" declarations which just bloat host side code. There are still some more <asm/arch/XYZ.h> ==> <mach/XYZ.h> changes needed in this driver, catching up to the relocation of most of the include/asm-arm/arch-* contents. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: stable <stable@kernel.org> [2.6.27] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: do not mess up count number and CSR0 register valueBryan Wu2008-10-171-12/+12
| | | | | | | Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* OMAP:MUSB: Corrects urb unlink function pathAjay Kumar Gupta2008-10-171-2/+5
| | | | | | | | | | | | | | | Fixes kernel panic while ISO IN transfer is aborted.Replaced usb_hcd_unlink_urb_from_ep() from musb_giveback() to __musb_giveback() to make sure urb is unlinked before giveback when __musb_giveback() is called from musb_urb_dequeue(). Acquired musb->lock() before usb_hcd_unlink_urb_from_ep() within in enqueue path. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* OMAP:MUSB: Fixes the TT programming.Ajay Kumar Gupta2008-10-171-1/+5
| | | | | | | | | | | Fixes enumeration failures when a USB device attached to a LS hub is connected to OMAP EVM via HS hub. This is fixed by correctly programming hub address register in enqueue path. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* musb: io: only define read/write stubs if they're not defined yetFelipe Balbi2008-10-171-1/+3
| | | | | | | | | | | | | | | For those archs which don't provide read/write friends we provide our own implementation so musb driver won't break compilation. This is temporary fix until a better solution comes from upstream. Idealy, <linux/io.h> would provide those calls if the architecture did not provide them yet. In that case being possible to remove all those stubs from musb_io.h Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Fix s3c2410_udc usb speed handlingYauhen Kharuzhy2008-10-171-1/+1
| | | | | | | | | | | | | | | The new composite framework revealed a weakness in the s3c2410_udc driver gadget register function. Instead of checking if speed asked for was USB_LOW_SPEED upon usb_gadget_register() to deny service, it checked only for USB_FULL_SPEED, thus denying service to usb high speed capable gadgets (like g_ether). Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb gadget: USB_GADGET_VBUS_DRAW Kconfig optionDavid Brownell2008-10-1710-15/+25
| | | | | | | | | | | | | | | | | | Offer a "how much VBUS power to request" configuration option for USB gadgets that aren't using board-specific customization of their gadget or (composite) configuration drivers. Also remove a couple pointless "depends on USB_GADGET" bits from the Kconfig text; booleans inside an "if USB_GADGET" will already have that dependency. Based on a patch from Justin Clacherty. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Justin Clacherty <justin@redfish-group.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* MUSB: Add sanity check for maximum number of endpointsKevin Hilman2008-10-171-0/+1
| | | | | | | | | | | | | | There is no check if platform code passes in more endpoints (num_eps) than the maximum number of enpoints (MUSB_C_NUM_EPS.) The result is that allocate_instance() happily writes past the end of 'struct musb' corrupting memory. This patch adds a BUG() if the platform code requests more than the max. Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: remove code associated with !CONFIG_PPC_MERGEKumar Gala2008-10-174-223/+0
| | | | | | | | | | | | Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove the dead code associated with !CONFIG_PPC_MERGE. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usbmon: fix tiny race exposed by the fastboot patchesArjan van de Ven2008-10-171-1/+1
| | | | | | | | | | | | | | | | | | usbmon registers the notifier chain, takes the bus lock and then goes to scan the existing devices for hooking up. Unfortunately, if usb_mon gets initialized while USB bus discovery is going on, it's possible that usbmon gets a notifier on one cpu (which runs without USB locks), and the scan is going on and also finds the new bus, resulting in a double sysfs registration, which then produces a WARNING. Pete Zaitcev did the bug diagnostics on this one Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Acked-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: change hub initialization sleeps to delayed_workAlan Stern2008-10-171-10/+81
| | | | | | | | | | | | | | | | | | This patch (as1137) changes the hub_activate() routine, replacing the power-power-up and debounce delays with delayed_work calls. The idea is that on systems where the USB stack is compiled into the kernel rather than built as modules, these delays will no longer block the boot thread. At least 100 ms is saved for each root hub, which can add up to a significant savings in total boot time. Arjan van de Ven was very pleased to see that this shaved 700 ms off his computer's boot time. Since his total boot time is on the order of two seconds, the improvement is considerable. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci-dbg: fix reading less content of periodic fileMing Lei2008-10-171-3/+5
| | | | | | | | | | | | | | | This patch fix 2 problems about reading periodic file: 1. The "..." after a interrupt qh is missed because buffer pointer is not moved. 2. After setting p.ptr as NULL, its next qh or itd will be omited and can't be stored in debug buffer. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci-dbg: increase debug buffer size for periodic fileMing Lei2008-10-172-19/+26
| | | | | | | | | | | | | | | | | This patch is based on the following ideas: 1. Some usb devices (such as usb video class) have endpoints of high interval attribute, so reading "periodic" file need more debug buffer to accommodate the qh or itd schedule information. For example, 4KB buffer is not enough for a single interrupt qh of 2ms period. 2. print a %p need 16 byte buffer on 64-bits arch, but 8 byte on 32-bits arch. Add a extra bonus for 64-bits arch. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: gadget: workaround storage command size issuesFelipe Balbi2008-10-171-4/+17
| | | | | | | | | | Try to workaround issues with bad SCSI implementations by ignoring the command size error. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: g_printer: fix handling zero-length packetSangSu Park2008-10-171-2/+1
| | | | | | | | | | | | | g_printer doesn't have to check whether the data size is a multiple of MaxPacketSize, because device controller driver already make that check. Signed-off-by: SangSu Park<sangsu@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Fix spelling in usb/serial.hGeoff Levand2008-10-171-1/+1
| | | | | | | | Fixes a minor typo in the comments for usb_set_serial_data. Signed-off-by: Geoff Levand <geoff@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Fix doc for usb_autopm_enableGeoff Levand2008-10-171-4/+4
| | | | | | | | | | Correct errors in the descriptions for usb_autopm_enable and usb_autopm_disable in the USB PM doc. Signed-off-by: Geoff Levand <geoff@infradead.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB Serial: Sierra: debug message fixKevin Lloyd2008-10-171-31/+38
| | | | | | | | | This patch moves dbg calls to dev_dbg where possible. It also fixes some issues with a previous submission aiming to do the same thing. Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: RESET_RESUME needs to block autosuspend when remote wakeup is neededOliver Neukum2008-10-171-1/+2
| | | | | | | | | | Reset upon resumption will wipe the input buffer and is therefore a reason to not suspend if remote wakeup is requested because the driver needs that data. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ftdi_sio: fix 'product' parameter descriptionPaulius Zaleckas2008-10-171-1/+1
| | | | | | Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb core: fix USB_OTG_BLACKLIST_HUB typoPeter Korsgaard2008-10-171-1/+1
| | | | | | Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Documentation/usb/anchors.txt #2Oliver Neukum2008-10-171-0/+17
| | | | | | | | This adds Documentation for the extensions of the anchor API. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* OHCI: Allow broken controllers to auto-stopAlan Stern2008-10-171-28/+32
| | | | | | | | | | | | | | | | | | | | This patch (as1134) attempts to improve the way we handle OHCI controllers with broken Root Hub Status Change interrupt support. In these controllers the RHSC interrupt bit essentially never turns off, making RHSC interrupts useless -- they have to remain permanently disabled. Such controllers should still be allowed to turn off their root hubs when no devices are attached. Polling for new connections can continue while the root hub is suspended. The patch implements this feature. (It won't have much effect unless CONFIG_PM is enabled and CONFIG_USB_SUSPEND is disabled, but since the overhead is very small we may as well do it.) Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb-storage: report underflow with no sense dataAlan Stern2008-10-171-1/+1
| | | | | | | | | | | | | | | | | | This patch (as1118) addresses a problem with certain USB mass-storage devices. These devices sometimes return less data than asked for and then provide no sense data to explain the problem. Currently usb-storage leaves it up to the SCSI layer to decide how this should be handled, and the SCSI layer interprets the lack of sense data to mean that nothing went wrong. But if we got less data than required then something definitely _did_ go wrong, and we should say so. The patch tells the SCSI layer to retry the command when this sort of thing happens. Retrying may not solve the underlying problem, but it's better than believing that data was transferred when it wasn't. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: add Freescale QE/CPM USB peripheral controller driverLi Yang2008-10-175-0/+3188
| | | | | | | | | | | | | | | Some of Freescale SoC chips have a QE or CPM co-processor which supports full speed USB. The driver adds device mode support of both QE and CPM USB controller to Linux USB gadget. The driver is tested with MPC8360 and MPC8272, and should work with other models having QE/CPM given minor tweaks. Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: drivers/usb/misc: Use an IS_ERR test rather than a NULL testJulien Brunel2008-10-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | In case of error, the function backlight_device_register returns an ERR pointer, but never returns a NULL pointer. So a NULL test that may come after a call to this function should be strengthened by an IS_ERR test. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @match_bad_null_test@ expression x, E; statement S1,S2; @@ x = backlight_device_register(...) ... when != x = E * if (x != NULL) S1 else S2 // </smpl> Signed-off-by: Julien Brunel <brunel@diku.dk> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: remove unused #include <version.h>Huang Weiyi2008-10-171-1/+0
| | | | | | | | | | | The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/usb/gadget/pxa27x_udc.c This patch removes the said #include <version.h>. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb gadget: defer obex enumerationDavid Brownell2008-10-171-7/+54
| | | | | | | | | | | | Some USB peripheral controller drivers support software control over the data pullup. Use those controls to prevent the OBEX function from enumerating until the userspace server has opened the /dev/ttyGS* node it will use to implement protocol chitchat with the USB host. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb gadget: cdc obex glueFelipe Balbi2008-10-176-2/+479
| | | | | | | | | | | | | The following patch introduces a new f_obex.c function driver. It allows userspace obex servers to use usb as transport layer for their messages. [ dbrownell@users.sourceforge.net: various fixes and cleanups ] Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-23 10:41:37 +0100