summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Merge tag 'asoc-fix-v5.7-rc2' of ↵Takashi Iwai2020-04-2132-263/+509
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus ASoC: Fixes for v5.7 Quite a lot of fixes here, a lot of driver specific ones but the biggest one is the revert of changes to the startup and shutdown sequence for DAIs that went in during the merge window - they broke some older x86 platforms and attempts to fix them didn't succeed so it's safer to just roll them back and try to make sure those platforms are handled properly in any future attempt. The rockchip S/PDIF DT stuff was IIRC for validation issues.
| * ASoC: wm8960: Fix wrong clock after suspend & resumeShengjiu Wang2020-04-211-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After suspend & resume, wm8960_hw_params may be called when bias_level is not SND_SOC_BIAS_ON, then wm8960_configure_clocking is not called. But if sample rate is changed at that time, then the output clock rate will be not correct. So judgement of bias_level is SND_SOC_BIAS_ON in wm8960_hw_params is not necessary and it causes above issue. Fixes: 3176bf2d7ccd ("ASoC: wm8960: update pll and clock setting function") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/1587468525-27514-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: wm89xx: Add missing dependencyYueHaibing2020-04-201-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sound/soc/codecs/wm8900.o: In function `wm8900_i2c_probe': wm8900.c:(.text+0xa36): undefined reference to `__devm_regmap_init_i2c' sound/soc/codecs/wm8900.o: In function `wm8900_modinit': wm8900.c:(.init.text+0xb): undefined reference to `i2c_register_driver' sound/soc/codecs/wm8900.o: In function `wm8900_exit': wm8900.c:(.exit.text+0x8): undefined reference to `i2c_del_driver' sound/soc/codecs/wm8988.o: In function `wm8988_i2c_probe': wm8988.c:(.text+0x857): undefined reference to `__devm_regmap_init_i2c' sound/soc/codecs/wm8988.o: In function `wm8988_modinit': wm8988.c:(.init.text+0xb): undefined reference to `i2c_register_driver' sound/soc/codecs/wm8988.o: In function `wm8988_exit': wm8988.c:(.exit.text+0x8): undefined reference to `i2c_del_driver' sound/soc/codecs/wm8995.o: In function `wm8995_i2c_probe': wm8995.c:(.text+0x1c4f): undefined reference to `__devm_regmap_init_i2c' sound/soc/codecs/wm8995.o: In function `wm8995_modinit': wm8995.c:(.init.text+0xb): undefined reference to `i2c_register_driver' sound/soc/codecs/wm8995.o: In function `wm8995_exit': wm8995.c:(.exit.text+0x8): undefined reference to `i2c_del_driver' Add SND_SOC_I2C_AND_SPI dependency to fix this. Fixes: ea00d95200d02ece ("ASoC: Use imply for SND_SOC_ALL_CODECS") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200420125343.20920-1-yuehaibing@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * Merge series "ASoC: rsnd: multi-SSI setup fixes" from Matthias Blankertz ↵Mark Brown2020-04-201-5/+14
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | <matthias.blankertz@cetitec.com>: Fix rsnd_dai_call() operations being performed twice for the master SSI in multi-SSI setups, and fix the rsnd_ssi_stop operation for multi-SSI setups. The only visible effect of these issues was some "status check failed" spam when the rsnd_ssi_stop was called, but overall the code is cleaner now, and some questionable writes to the SSICR register which did not lead to any observable misbehaviour but were contrary to the datasheet are fixed. Mark: The first patch kind of reverts my "ASoC: rsnd: Fix parent SSI start/stop in multi-SSI mode" from a few days ago and achieves the same effect in a simpler fashion, if you would prefer a clean patch series based on v5.6 drop me a note. Greetings, Matthias Matthias Blankertz (2): ASoC: rsnd: Don't treat master SSI in multi SSI setup as parent ASoC: rsnd: Fix "status check failed" spam for multi-SSI sound/soc/sh/rcar/ssi.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-) base-commit: 15a5760cb8b6d5c1ebbf1d2e1f0b77380ab68a82 -- 2.26.1
| | * ASoC: rsnd: Fix "status check failed" spam for multi-SSIMatthias Blankertz2020-04-201-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the rsnd_ssi_stop function to skip disabling the individual SSIs of a multi-SSI setup, as the actual stop is performed by rsnd_ssiu_stop_gen2 - the same logic as in rsnd_ssi_start. The attempt to disable these SSIs was harmless, but caused a "status check failed" message to be printed for every SSI in the multi-SSI setup. The disabling of interrupts is still performed, as they are enabled for all SSIs in rsnd_ssi_init, but care is taken to not accidentally set the EN bit for an SSI where it was not set by rsnd_ssi_start. Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20200417153017.1744454-3-matthias.blankertz@cetitec.com Signed-off-by: Mark Brown <broonie@kernel.org>
| | * ASoC: rsnd: Don't treat master SSI in multi SSI setup as parentMatthias Blankertz2020-04-201-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The master SSI of a multi-SSI setup was attached both to the RSND_MOD_SSI slot and the RSND_MOD_SSIP slot of the rsnd_dai_stream. This is not correct wrt. the meaning of being "parent" in the rest of the SSI code, where it seems to indicate an SSI that provides clock and word sync but is not transmitting/receiving audio data. Not treating the multi-SSI master as parent allows removal of various special cases to the rsnd_ssi_is_parent conditions introduced in commit a09fb3f28a60 ("ASoC: rsnd: Fix parent SSI start/stop in multi-SSI mode"). It also fixes the issue that operations performed via rsnd_dai_call() were performed twice for the master SSI. This caused some "status check failed" spam when stopping a multi-SSI stream as the driver attempted to stop the master SSI twice. Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20200417153017.1744454-2-matthias.blankertz@cetitec.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * | Merge series "ASoC: meson: fix codec-to-codec link setup" from Jerome Brunet ↵Mark Brown2020-04-202-2/+6
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | <jbrunet@baylibre.com>: This patchset fixes the problem reported by Marc in this thread [0] The problem was due to an error in the meson card drivers which had the "no_pcm" dai_link property set on codec-to-codec links [0]: https://lore.kernel.org/r/20200417122732.GC5315@sirena.org.uk Jerome Brunet (2): ASoC: meson: axg-card: fix codec-to-codec link setup ASoC: meson: gx-card: fix codec-to-codec link setup sound/soc/meson/axg-card.c | 4 +++- sound/soc/meson/gx-card.c | 4 +++- 2 files changed, 6 insertions(+), 2 deletions(-) -- 2.25.2
| | * | ASoC: meson: gx-card: fix codec-to-codec link setupJerome Brunet2020-04-201-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the addition of commit 9b5db059366a ("ASoC: soc-pcm: dpcm: Only allow playback/capture if supported"), meson-axg cards which have codec-to-codec links fail to init and Oops. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000128 Internal error: Oops: 96000044 [#1] PREEMPT SMP CPU: 3 PID: 1582 Comm: arecord Not tainted 5.7.0-rc1 pc : invalidate_paths_ep+0x30/0xe0 lr : snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8 Call trace: invalidate_paths_ep+0x30/0xe0 snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8 dpcm_path_get+0x38/0xd0 dpcm_fe_dai_open+0x70/0x920 snd_pcm_open_substream+0x564/0x840 snd_pcm_open+0xfc/0x228 snd_pcm_capture_open+0x4c/0x78 snd_open+0xac/0x1a8 ... While this error was initially reported the axg-card type, it also applies to the gx-card type. While initiliazing the links, ASoC treats the codec-to-codec links of this card type as a DPCM backend. This error eventually leads to the Oops. Most of the card driver code is shared between DPCM backends and codec-to-codec links. The property "no_pcm" marking DCPM BE was left set on codec-to-codec links, leading to this problem. This commit fixes that. Fixes: e37a0c313a0f ("ASoC: meson: gx: add sound card support") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20200420114511.450560-3-jbrunet@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org>
| | * | ASoC: meson: axg-card: fix codec-to-codec link setupJerome Brunet2020-04-201-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the addition of commit 9b5db059366a ("ASoC: soc-pcm: dpcm: Only allow playback/capture if supported"), meson-axg cards which have codec-to-codec links fail to init and Oops: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000128 Internal error: Oops: 96000044 [#1] PREEMPT SMP CPU: 3 PID: 1582 Comm: arecord Not tainted 5.7.0-rc1 pc : invalidate_paths_ep+0x30/0xe0 lr : snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8 Call trace: invalidate_paths_ep+0x30/0xe0 snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8 dpcm_path_get+0x38/0xd0 dpcm_fe_dai_open+0x70/0x920 snd_pcm_open_substream+0x564/0x840 snd_pcm_open+0xfc/0x228 snd_pcm_capture_open+0x4c/0x78 snd_open+0xac/0x1a8 ... While initiliazing the links, ASoC treats the codec-to-codec links of this card type as a DPCM backend. This error eventually leads to the Oops. Most of the card driver code is shared between DPCM backends and codec-to-codec links. The property "no_pcm" marking DCPM BE was left set on codec-to-codec links, leading to this problem. This commit fixes that. Fixes: 0a8f1117a680 ("ASoC: meson: axg-card: add basic codec-to-codec link support") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20200420114511.450560-2-jbrunet@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * | | ASoC: dapm: fixup dapm kcontrol widgetGyeongtaek Lee2020-04-201-3/+17
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | snd_soc_dapm_kcontrol widget which is created by autodisable control should contain correct on_val, mask and shift because it is set when the widget is powered and changed value is applied on registers by following code in dapm_seq_run_coalesced(). mask |= w->mask << w->shift; if (w->power) value |= w->on_val << w->shift; else value |= w->off_val << w->shift; Shift on the mask in dapm_kcontrol_data_alloc() is removed to prevent double shift. And, on_val in dapm_kcontrol_set_value() is modified to get correct value in the dapm_seq_run_coalesced(). Signed-off-by: Gyeongtaek Lee <gt82.lee@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/000001d61537$b212f620$1638e260$@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * | ASoC: SOF: Intel: add min/max channels for SSP on Baytrail/BroadwellPierre-Louis Bossart2020-04-172-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Major regressions were detected by SOF CI on CherryTrail and Broadwell: [ 25.705750] SSP2-Codec: ASoC: no backend playback stream [ 27.923378] SSP2-Codec: ASoC: no users playback at close - state This is root-caused to the introduction of the DAI capability checks with snd_soc_dai_stream_valid(). Its use in soc-pcm.c makes it a requirement for all DAIs to report at least a non-zero min_channels field. For some reason the SSP structures used for SKL+ did provide this information but legacy platforms didn't. Fixes: 9b5db059366ae2 ("ASoC: soc-pcm: dpcm: Only allow playback/capture if supported") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20200417172014.11760-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * | ASoC: stm32: sai: fix sai probeOlivier Moysan2020-04-171-7/+5
| |/ | | | | | | | | | | | | | | | | | | pcm config must be set before snd_dmaengine_pcm_register() call. Fixes: 0d6defc7e0e4 ("ASoC: stm32: sai: manage rebind issue") Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Link: https://lore.kernel.org/r/20200417142122.10212-1-olivier.moysan@st.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * Merge series "ASoC: rsnd: Fixes for multichannel HDMI audio output" from ↵Mark Brown2020-04-162-5/+5
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Matthias Blankertz <matthias.blankertz@cetitec.com>: This fixes two issues in the snd-soc-rcar driver blocking multichannel HDMI audio out: The parent SSI in a multi-SSI configuration is not correctly set up and started, and the SSI->HDMI channel mapping is wrong. With these patches, the following device tree snippet can be used on an r8a7795-based platform (Salvator-X) to enable multichannel HDMI audio on HDMI0: rsnd_port1: port@1 { rsnd_endpoint1: endpoint { remote-endpoint = <&dw_hdmi0_snd_in>; dai-format = "i2s"; bitclock-master = <&rsnd_endpoint1>; frame-master = <&rsnd_endpoint1>; playback = <&ssi0 &ssi1 &ssi2 &ssi9>; }; }; With a capable receiver attached, all of 2ch (stereo), 6ch (e.g. 5.1) and 8ch audio output should work. Matthias Blankertz (2): ASoC: rsnd: Fix parent SSI start/stop in multi-SSI mode ASoC: rsnd: Fix HDMI channel mapping for multi-SSI mode sound/soc/sh/rcar/ssi.c | 8 ++++---- sound/soc/sh/rcar/ssiu.c | 2 +- 2 files changed, 5 insertions(+), 5 deletions(-) base-commit: 7111951b8d4973bda27ff663f2cf18b663d15b48 -- 2.26.0
| | * ASoC: rsnd: Fix HDMI channel mapping for multi-SSI modeMatthias Blankertz2020-04-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HDMI?_SEL register maps up to four stereo SSI data lanes onto the sdata[0..3] inputs of the HDMI output block. The upper half of the register contains four blocks of 4 bits, with the most significant controlling the sdata3 line and the least significant the sdata0 line. The shift calculation has an off-by-one error, causing the parent SSI to be mapped to sdata3, the first multi-SSI child to sdata0 and so forth. As the parent SSI transmits the stereo L/R channels, and the HDMI core expects it on the sdata0 line, this causes no audio to be output when playing stereo audio on a multichannel capable HDMI out, and multichannel audio has permutated channels. Fix the shift calculation to map the parent SSI to sdata0, the first child to sdata1 etc. Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20200415141017.384017-3-matthias.blankertz@cetitec.com Signed-off-by: Mark Brown <broonie@kernel.org>
| | * ASoC: rsnd: Fix parent SSI start/stop in multi-SSI modeMatthias Blankertz2020-04-161-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The parent SSI of a multi-SSI setup must be fully setup, started and stopped since it is also part of the playback/capture setup. So only skip the SSI (as per commit 203cdf51f288 ("ASoC: rsnd: SSI parent cares SWSP bit") and commit 597b046f0d99 ("ASoC: rsnd: control SSICR::EN correctly")) if the SSI is parent outside of a multi-SSI setup. Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20200415141017.384017-2-matthias.blankertz@cetitec.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * | ASoC: codecs: hdac_hdmi: Fix incorrect use of list_for_each_entryAmadeusz Sławiński2020-04-161-3/+3
| |/ | | | | | | | | | | | | | | | | | | If we don't find any pcm, pcm will point at address at an offset from the the list head and not a meaningful structure. Fix this by returning correct pcm if found and NULL if not. Found with coccinelle. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Link: https://lore.kernel.org/r/20200415162849.308-1-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: soc-dai: revert all changes to DAI startup/shutdown sequencePierre-Louis Bossart2020-04-162-10/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Baytrail/Cherrytrail, the Atom/SST driver fails miserably: [ 9.741953] intel_sst_acpi 80860F28:00: FW Version 01.0c.00.01 [ 9.832992] intel_sst_acpi 80860F28:00: FW sent error response 0x40034 [ 9.833019] intel_sst_acpi 80860F28:00: FW alloc failed ret -4 [ 9.833028] intel_sst_acpi 80860F28:00: sst_get_stream returned err -5 [ 9.833033] sst-mfld-platform sst-mfld-platform: ASoC: DAI prepare error: -5 [ 9.833037] Baytrail Audio Port: ASoC: prepare FE Baytrail Audio Port failed [ 9.853942] intel_sst_acpi 80860F28:00: FW sent error response 0x40034 [ 9.853974] intel_sst_acpi 80860F28:00: FW alloc failed ret -4 [ 9.853984] intel_sst_acpi 80860F28:00: sst_get_stream returned err -5 [ 9.853990] sst-mfld-platform sst-mfld-platform: ASoC: DAI prepare error: -5 [ 9.853994] Baytrail Audio Port: ASoC: prepare FE Baytrail Audio Port failed Commit b56be800f1292 ("ASoC: soc-pcm: call snd_soc_dai_startup()/shutdown() once") was the initial problematic commit. Commit 1ba616bd1a6d5e ("ASoC: soc-dai: fix DAI startup/shutdown sequence") was an attempt to fix things but it does not work on Baytrail, reverting all changes seems necessary for now. Fixes: 1ba616bd1a6d5e ("ASoC: soc-dai: fix DAI startup/shutdown sequence") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200415030437.23803-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: topology: Fix endianness issueAmadeusz Sławiński2020-04-151-1/+1
| | | | | | | | | | | | | | | | | | As done in already existing cases, we should use le32_to_cpu macro while accessing hdr->magic. Found with sparse. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Link: https://lore.kernel.org/r/20200415162435.31859-2-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: q6dsp6: q6afe-dai: add missing channels to MI2S DAIsStephan Gerhold2020-04-151-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For some reason, the MI2S DAIs do not have channels_min/max defined. This means that snd_soc_dai_stream_valid() returns false, i.e. the DAIs have neither valid playback nor capture stream. It's quite surprising that this ever worked correctly, but in 5.7-rc1 this is now failing badly: :) Commit 0e9cf4c452ad ("ASoC: pcm: check if cpu-dai supports a given stream") introduced a check for snd_soc_dai_stream_valid() before calling hw_params(), which means that the q6i2s_hw_params() function was never called, eventually resulting in: qcom-q6afe aprsvc:q6afe:4:4: no line is assigned ... even though "qcom,sd-lines" is set in the device tree. Commit 9b5db059366a ("ASoC: soc-pcm: dpcm: Only allow playback/capture if supported") now even avoids creating PCM devices if the stream is not supported, which means that it is failing even earlier with e.g.: Primary MI2S: ASoC: no backend playback stream Avoid all that trouble by adding channels_min/max for the MI2S DAIs. Fixes: 24c4cbcfac09 ("ASoC: qdsp6: q6afe: Add q6afe dai driver") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20200415150050.616392-1-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: soc-pcm: dpcm: Only allow playback/capture if supportedStephan Gerhold2020-04-151-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At the moment, PCM devices for DPCM are only created based on the dpcm_playback/capture parameters of the DAI link, without considering if the CPU/FE DAI is actually capable of playback/capture. Normally the dpcm_playback/capture parameter should match the capabilities of the CPU DAI. However, there is no way to set that parameter from the device tree (e.g. with simple-audio-card or qcom sound cards). dpcm_playback/capture are always both set to 1. This causes problems when the CPU DAI does only support playback or capture. Attemting to open that PCM device with an unsupported stream type then results in a null pointer dereference: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000128 Internal error: Oops: 96000044 [#1] PREEMPT SMP CPU: 3 PID: 1582 Comm: arecord Not tainted 5.7.0-rc1 pc : invalidate_paths_ep+0x30/0xe0 lr : snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8 Call trace: invalidate_paths_ep+0x30/0xe0 snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8 dpcm_path_get+0x38/0xd0 dpcm_fe_dai_open+0x70/0x920 snd_pcm_open_substream+0x564/0x840 snd_pcm_open+0xfc/0x228 snd_pcm_capture_open+0x4c/0x78 snd_open+0xac/0x1a8 ... ... because the DAI playback/capture_widget is not set in that case. We could add checks there to fix the problem (maybe we should anyway), but much easier is to not expose the device as playback/capture in the first place. Attemting to use that device would always fail later anyway. Add checks for snd_soc_dai_stream_valid() to the DPCM case to avoid exposing playback/capture if it is not supported. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20200415104928.86091-1-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: sgtl5000: Fix VAG power-on handlingSebastian Reichel2020-04-152-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As mentioned slightly out of patch context in the code, there is no reset routine for the chip. On boards where the chip is supplied by a fixed regulator, it might not even be resetted during (e.g. watchdog) reboot and can be in any state. If the device is probed with VAG enabled, the driver's probe routine will generate a loud pop sound when ANA_POWER is being programmed. Avoid this by properly disabling just the VAG bit and waiting the required power down time. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Fabio Estevam <festivem@gmail.com> Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: rockchip-i2s: add power-domains propertyJohan Jonker2020-04-141-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | In the old txt situation we add/describe only properties that are used by the driver/hardware itself. With yaml it also filters things in a node that are used by other drivers like 'power-domains' for rk3399, so add it to 'rockchip-i2s.yaml'. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200324094149.6904-3-jbx6244@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: madera: Remove a couple of stray blank linesCharles Keepax2020-04-141-4/+0
| | | | | | | | | | | | Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200409181311.30247-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: wsa881x: mark read_only_wordlength flagSrinivas Kandagatla2020-04-141-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | WSA881x works in PDM mode so the wordlength is fixed, which also makes the only field "WordLength" in DPN_BlockCtrl1 register a read-only. Writing to this register will throw up errors with Qualcomm Controller. So use ro_blockctrl1_reg flag to mark this field as read-only so that core will not write to this register. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20200414110347.23829-1-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: qcom: common: Silence duplicate parse error messagesBjorn Andersson2020-04-142-6/+2
| | | | | | | | | | | | | | | | | | | | All error paths in qcom_snd_parse_of() prints more specific error messages, so silence the one in apq8096_platform_probe() and sdm845_snd_platform_probe() to avoid spamming the kernel log. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200406003229.2354631-1-bjorn.andersson@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
| * soc/stm/stm32_sub_sai: Add missing '\n' in log messagesSebastian Fricke2020-04-141-1/+1
| | | | | | | | | | | | | | | | | | | | Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'. Fixes: 3e086ed("ASoC: stm32: add SAI drivers") Signed-off-by: Sebastian Fricke <sebastian.fricke.linux@gmail.com> Link: https://lore.kernel.org/r/20200413042952.7675-1-sebastian.fricke.linux@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: dapm: Remove dapm_connect_dai_link_widgets helperCharles Keepax2020-04-141-22/+14
| | | | | | | | | | | | | | | | | | This helper is adding very little both it and is one caller are very small functions simply combine the two. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200409181209.30130-3-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: dapm: Move error message to avoid some duplicationCharles Keepax2020-04-141-12/+4
| | | | | | | | | | | | | | | | | | | | Move the error message into snd_soc_dapm_new_dai from dapm_connect_dai_pair, since the two copies are almost identical and are the only callers. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200409181209.30130-2-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: rockchip-spdif: add power-domains propertyJohan Jonker2020-04-141-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | In the old txt situation we add/describe only properties that are used by the driver/hardware itself. With yaml it also filters things in a node that are used by other drivers like 'power-domains' for rk3399, so add it to 'rockchip-spdif.yaml'. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200404115225.4314-3-jbx6244@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: rockchip-spdif: add #sound-dai-cells propertyJohan Jonker2020-04-141-0/+5
| | | | | | | | | | | | | | | | | | | | | | '#sound-dai-cells' is required to properly interpret the list of DAI specified in the 'sound-dai' property, so add them to 'rockchip-spdif.yaml' Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200404115225.4314-2-jbx6244@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: convert rockchip spdif bindings to yamlJohan Jonker2020-04-142-45/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current dts files with 'spdif' nodes are manually verified. In order to automate this process rockchip-spdif.txt has to be converted to yaml. Also rk3188.dtsi, rk3288.dtsi use an extra fallback string, so change this in the documentation. Changed: "rockchip,rk3188-spdif", "rockchip,rk3066-spdif" "rockchip,rk3288-spdif", "rockchip,rk3066-spdif" Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200404115225.4314-1-jbx6244@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: Intel: soc-acpi-intel-cml-match: remove useless 'rt1308_2_adr'Jason Yan2020-04-141-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the following gcc warning: sound/soc/intel/common/soc-acpi-intel-cml-match.c:116:45: warning: ‘rt1308_2_adr’ defined but not used [-Wunused-const-variable=] static const struct snd_soc_acpi_adr_device rt1308_2_adr[] = { ^~~~~~~~~~~~ Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Link: https://lore.kernel.org/r/20200410081117.21319-2-yanaijie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: intel: soc-acpi-intel-icl-match: remove useless 'rt1308_2_adr'Jason Yan2020-04-141-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the following gcc warning: sound/soc/intel/common/soc-acpi-intel-icl-match.c:90:45: warning: ‘rt1308_2_adr’ defined but not used [-Wunused-const-variable=] static const struct snd_soc_acpi_adr_device rt1308_2_adr[] = { ^~~~~~~~~~~~ Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200410081117.21319-1-yanaijie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: amd: Fix button configurationAkshu Agrawal2020-04-141-3/+3
| | | | | | | | | | | | | | | | RT5682 buttons were incorrectly mapped. Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com> Link: https://lore.kernel.org/r/20200414113527.13532-1-akshu.agrawal@amd.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: tas571x: disable regulators on failed probePhilipp Puschmann2020-04-141-5/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If probe fails after enabling the regulators regulator_put is called for each supply without having them disabled before. This produces some warnings like WARNING: CPU: 0 PID: 90 at drivers/regulator/core.c:2044 _regulator_put.part.0+0x154/0x15c [<c010f7a8>] (unwind_backtrace) from [<c010c544>] (show_stack+0x10/0x14) [<c010c544>] (show_stack) from [<c012b640>] (__warn+0xd0/0xf4) [<c012b640>] (__warn) from [<c012b9b4>] (warn_slowpath_fmt+0x64/0xc4) [<c012b9b4>] (warn_slowpath_fmt) from [<c04c4064>] (_regulator_put.part.0+0x154/0x15c) [<c04c4064>] (_regulator_put.part.0) from [<c04c4094>] (regulator_put+0x28/0x38) [<c04c4094>] (regulator_put) from [<c04c40cc>] (regulator_bulk_free+0x28/0x38) [<c04c40cc>] (regulator_bulk_free) from [<c0579b2c>] (release_nodes+0x1d0/0x22c) [<c0579b2c>] (release_nodes) from [<c05756dc>] (really_probe+0x108/0x34c) [<c05756dc>] (really_probe) from [<c0575aec>] (driver_probe_device+0xb8/0x16c) [<c0575aec>] (driver_probe_device) from [<c0575d40>] (device_driver_attach+0x58/0x60) [<c0575d40>] (device_driver_attach) from [<c0575da0>] (__driver_attach+0x58/0xcc) [<c0575da0>] (__driver_attach) from [<c0573978>] (bus_for_each_dev+0x78/0xc0) [<c0573978>] (bus_for_each_dev) from [<c0574b5c>] (bus_add_driver+0x188/0x1e0) [<c0574b5c>] (bus_add_driver) from [<c05768b0>] (driver_register+0x74/0x108) [<c05768b0>] (driver_register) from [<c061ab7c>] (i2c_register_driver+0x3c/0x88) [<c061ab7c>] (i2c_register_driver) from [<c0102df8>] (do_one_initcall+0x58/0x250) [<c0102df8>] (do_one_initcall) from [<c01a91bc>] (do_init_module+0x60/0x244) [<c01a91bc>] (do_init_module) from [<c01ab5a4>] (load_module+0x2180/0x2540) [<c01ab5a4>] (load_module) from [<c01abbd4>] (sys_finit_module+0xd0/0xe8) [<c01abbd4>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20) Fixes: 3fd6e7d9a146 (ASoC: tas571x: New driver for TI TAS571x power amplifiers) Signed-off-by: Philipp Puschmann <p.puschmann@pironex.de> Link: https://lore.kernel.org/r/20200414112754.3365406-1-p.puschmann@pironex.de Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: dapm: Fix regression introducing multiple copies of DAI widgetsCharles Keepax2020-04-142-43/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Refactoring was done to factor out the linking of DAI widgets into a helper function, dapm_add_valid_dai_widget. However when this was done, a regression was introduced for CODEC to CODEC links. It was over looked that the playback and capture variables persisted across all CODEC DAIs being processed, which ensured that the special DAI widget that is added for CODEC to CODEC links was only created once. This bug causes kernel panics during DAPM shutdown. To stick with the spirit of the original refactoring whilst fixing the issue, variables to hold the DAI widgets are added to snd_soc_dai_link. Furthermore the dapm_add_valid_dai_widget function is renamed to dapm_connect_dai_pair, the function only adds DAI widgets in the CODEC to CODEC case and its primary job is to add routes connecting two DAI widgets, making the original name quite misleading. Fixes: 6c4b13b51aa3 ("ASoC: Add dapm_add_valid_dai_widget helper") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200409181209.30130-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: samsung: s3c24xx-i2s: Fix build after removal of DAI suspend/resumeKrzysztof Kozlowski2020-04-142-57/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 450312b640f9 ("ASoC: soc-core: remove DAI suspend/resume") removed the DAI side suspend/resume hooks and switched entirely to component suspend/resume. However the Samsung SoC s3c-i2s-v2 driver was not updated. Move the suspend/resume hooks from s3c-i2s-v2.c to s3c2412-i2s.c while changing dai to component which allows to keep the struct snd_soc_component_driver const. This fixes build errors: sound/soc/samsung/s3c-i2s-v2.c: In function ‘s3c_i2sv2_register_component’: sound/soc/samsung/s3c-i2s-v2.c:730:9: error: ‘struct snd_soc_dai_driver’ has no member named ‘suspend’ dai_drv->suspend = s3c2412_i2s_suspend; Reported-by: Arnd Bergmann <arnd@arndb.de> Fixes: 450312b640f9 ("ASoC: soc-core: remove DAI suspend/resume") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20200413124548.28197-1-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: topology: Check return value of soc_tplg_dai_configAmadeusz Sławiński2020-04-091-2/+7
| | | | | | | | | | | | | | | | | | | | | | Function soc_tplg_dai_config can fail, check for and handle possible failure. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200327204729.397-7-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: topology: Check return value of pcm_new_verAmadeusz Sławiński2020-04-091-1/+3
| | | | | | | | | | | | | | | | | | | | | | Function pcm_new_ver can fail, so we should check it's return value and handle possible error. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200327204729.397-6-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: topology: Check soc_tplg_add_route return valueAmadeusz Sławiński2020-04-091-1/+3
| | | | | | | | | | | | | | | | | | | | | | Function soc_tplg_add_route can propagate error code from callback, we should check its return value and handle fail in correct way. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200327204729.397-5-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: topology: Check return value of soc_tplg_*_createAmadeusz Sławiński2020-04-091-6/+12
| | | | | | | | | | | | | | | | | | | | | | | | Functions soc_tplg_denum_create, soc_tplg_dmixer_create, soc_tplg_dbytes_create can fail, so their return values should be checked and error should be propagated. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200327204729.397-4-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: topology: Check return value of soc_tplg_create_tlvAmadeusz Sławiński2020-04-091-2/+14
| | | | | | | | | | | | | | | | | | | | | | Function soc_tplg_create_tlv can fail, so we should check if it succeded or not and proceed appropriately. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200327204729.397-3-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
| * ASoC: topology: Add missing memory checksAmadeusz Sławiński2020-04-091-13/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | kstrdup is an allocation function and it can fail, so its return value should be checked and handled appropriately. In order to check all cases, we need to modify set_stream_info to return a value, so check that everything went correctly when doing kstrdup(). Later add proper checks and error handlers. Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200327204729.397-2-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
* | ALSA: usb-audio: Apply async workaround for Scarlett 2i4 2nd genAlexander Tsoy2020-04-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Due to rounding error driver sometimes incorrectly calculate next packet size, which results in audible clicks on devices with synchronous playback endpoints. For example on a high speed bus and a sample rate 44.1 kHz it loses one sample every ~40.9 seconds. Fortunately playback interface on Scarlett 2i4 2nd gen has a working explicit feedback endpoint, so we can switch playback data endpoint to asynchronous mode as a workaround. Signed-off-by: Alexander Tsoy <alexander@tsoy.me> Link: https://lore.kernel.org/r/20200421190908.462860-1-alexander@tsoy.me Signed-off-by: Takashi Iwai <tiwai@suse.de>
* | ALSA: usx2y: Fix potential NULL dereferenceTakashi Iwai2020-04-211-0/+2
| | | | | | | | | | | | | | | | | | | | | | The error handling code in usX2Y_rate_set() may hit a potential NULL dereference when an error occurs before allocating all us->urb[]. Add a proper NULL check for fixing the corner case. Reported-by: Lin Yi <teroincn@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200420075529.27203-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
* | ALSA: usb-audio: Add quirk for Focusrite Scarlett 2i2Gregor Pintar2020-04-212-84/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Force it to use asynchronous playback. Same quirk has already been added for Focusrite Scarlett Solo (2nd gen) with a commit 46f5710f0b88 ("ALSA: usb-audio: Add quirk for Focusrite Scarlett Solo"). This also seems to prevent regular clicks when playing at 44100Hz on Scarlett 2i2 (2nd gen). I did not notice any side effects. Moved both quirks to snd_usb_audioformat_attributes_quirk() as suggested. Signed-off-by: Gregor Pintar <grpintar@gmail.com> Reviewed-by: Alexander Tsoy <alexander@tsoy.me> Link: https://lore.kernel.org/r/20200420214030.2361-1-grpintar@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
* | ALSA: usb-audio: Add static mapping table for ALC1220-VB-based mobosTakashi Iwai2020-04-203-6/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TRX40 mobos from MSI and others with ALC1220-VB USB-audio device need yet more quirks for the proper control names. This patch provides the mapping table for those boards, correcting the FU names for volume and mute controls as well as the terminal names for jack controls. It also improves build_connector_control() not to add the directional suffix blindly if the string is given from the mapping table. With this patch applied, the new UCM profiles will be effective. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206873 Link: https://lore.kernel.org/r/20200420062036.28567-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
* | ALSA: hda: Remove ASUS ROG Zenith from the blacklistTakashi Iwai2020-04-191-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist") added a new blacklist for the devices that are known to have empty codecs, and one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f). However, it turned out that the very same PCI SSID is used for the previous model that does have the valid HD-audio codecs and the change broke the sound on it. This patch reverts the corresponding entry as a temporary solution. Although Zenith II and co will see get the empty HD-audio bus again, it'd be merely resource wastes and won't affect the functionality, so it's no end of the world. We'll need to address this later, e.g. by either switching to DMI string matching or using PCI ID & SSID pairs. Fixes: 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist") Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200419071926.22683-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
* | ALSA: hda/realtek - Fix unexpected init_amp overrideTakashi Iwai2020-04-181-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit 1c76aa5fb48d ("ALSA: hda/realtek - Allow skipping spec->init_amp detection") changed the way to assign spec->init_amp field that specifies the way to initialize the amp. Along with the change, the commit also replaced a few fixups that set spec->init_amp in HDA_FIXUP_ACT_PROBE with HDA_FIXUP_ACT_PRE_PROBE. This was rather aligning to the other fixups, and not supposed to change the actual behavior. However, this change turned out to cause a regression on FSC S7020, which hit exactly the above. The reason was that there is still one place that overrides spec->init_amp after HDA_FIXUP_ACT_PRE_PROBE call, namely in alc_ssid_check(). This patch fixes the regression by adding the proper spec->init_amp override check, i.e. verifying whether it's still ALC_INIT_UNDEFINED. Fixes: 1c76aa5fb48d ("ALSA: hda/realtek - Allow skipping spec->init_amp detection") Cc: <stable@vger.kernel.org> BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207329 Link: https://lore.kernel.org/r/20200418190639.10082-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
* | ALSA: usb-audio: Filter out unsupported sample rates on Focusrite devicesAlexander Tsoy2020-04-181-0/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many Focusrite devices supports a limited set of sample rates per altsetting. These includes audio interfaces with ADAT ports: - Scarlett 18i6, 18i8 1st gen, 18i20 1st gen; - Scarlett 18i8 2nd gen, 18i20 2nd gen; - Scarlett 18i8 3rd gen, 18i20 3rd gen; - Clarett 2Pre USB, 4Pre USB, 8Pre USB. Maximum rate is exposed in the last 4 bytes of Format Type descriptor which has a non-standard bLength = 10. Tested-by: Alexey Skobkin <skobkin-ru@ya.ru> Signed-off-by: Alexander Tsoy <alexander@tsoy.me> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200418175815.12211-1-alexander@tsoy.me Signed-off-by: Takashi Iwai <tiwai@suse.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-12 21:43:24 +0100