summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* [MTD] remove unused mtd parameter in of_mtd_parse_partitions()Sebastian Andrzej Siewior2008-10-134-6/+2
| | | | | Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGEKumar Gala2008-10-101-7/+0
| | | | | | | | | | | | Removed the Kconfig associated with 'NDFC NanD Flash Controller'. We can't enable !CONFIG_PPC_MERGE so there is no way to enable this. Additionally the code needs to get updated for arch/powerpc. For the time being lets just remove the Kconfig option so we can actually remove CONFIG_PPC_MERGE. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] driver extension to support NAND on TQM85xx modulesWolfgang Grandegger2008-10-102-5/+14
| | | | | | | | | | | | | | | | | This patch extends the FSL UPM NAND driver from Anton Vorontsov to support hardware which does not have the R/B pin of the NAND chip connected, like the TQM8548 module: - The OF_GPIO dependency has been removed from the Kconfig option because GPIO is not needed. The relevant gpio_* function are then stubbed out in <linux/gpio.h>. - It re-introduces the chip-delay property to define an appropriate maximum delay time (tR) required for read operations. The binding will be documented in a separate patch. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] fsl_upm: update driver for the new OF bindingsAnton Vorontsov2008-10-101-24/+33
| | | | | | | | | | | | | | - Get rid of fsl,wait-pattern and fsl,wait-write. I think this isn't chip-specific, and we should always do waits. I saw one board that didn't need fsl,wait-pattern, but I assume this was the exception that proves the rule; - Get rid of chip-delay. Today there are no users for this, and if anyone really need this they should push the OF bindings beforehand; - Now flash chips should be child nodes of the FSL UPM NAND controller; - Implement OF partition parsing. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [INFTL] Fix infinite loop in INFTL_foldchainDaniel Rosenthal2008-10-081-1/+4
| | | | | | | | | | | | | | | When iterating over a chain in reverse (oldest block first), this patch correctly marks the PUtable[] entry of the second to last erase block of a chain as BLOCK_NIL, regardless of whether or not it can format the last block successfully. Before, the second to last block was only marked as pointing to BLOCK_NIL if INFTL_formatblock() succeeded on the last block of the chain, which could potentially result in an infinite loop if the block was worn out and refused to format. Signed-off-by: Daniel Rosenthal <danielrosenthal@acm.org> Acked-by: Greg Ungerer <gerg@snapgear.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [MAPS] Maps: make uclinux mapping driver depend on MTD_RAM Mike Frysinger2008-09-271-1/+1
| | | | | | | | | ...since it only probes that Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NOR] intel_dc21285 switch to ROM APIAlan Cox2008-09-271-13/+3
| | | | | | | | Now that the needed helpers are exported, it becomes a nice simple switch over. Closes #9420 Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Export the ROM enable/disable helpersAlan Cox2008-09-272-2/+6
| | | | | | | .... so that they can be used by MTD map drivers. Lets us close #9420 Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NOR] fix cfi_cmdset_0001 FL_SYNCING race (take 2)Alexander Belyakov2008-09-271-2/+15
| | | | | | | | | | | | The patch fixes CFI issue with multipartitional devices leading to the set of errors or even deadlock. The problem is CFI FL_SYNCING state race with flash operations (e.g. erase suspend). It is reproduced by running intensive writes on one JFFS2 partition and simultaneously performing mount/unmount cycle on another partition of the same chip. Signed-off-by: Alexander Belyakov <abelyako@googlemail.com> Acked-by: Nicolas Pitre <nico@cam.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] nand_base.c: reset chip firstKarl Beldan2008-09-161-0/+8
| | | | | | | | | | Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx). The first command sent is NAND_CMD_READID. Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id. Tested with an MT29F4G08AAC. Signed-off-by: Karl Beldan <karl.beldan@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] OMAP2: add retry after read timeoutAdrian Hunter2008-09-161-3/+23
| | | | | | | | | Very occasionally, (about one in a million) read operations are ongoing after the timeout has expired. So, retry three times while the ongoing bit remains set. Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] Freescale i.MX2 NAND driverSascha Hauer2008-09-024-0/+1112
| | | | | | | | | | This patch adds support for the integrated NAND flash controller of the i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3 aswell. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Juergen Beisert <j.beisert@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] pxa3xx_nand: added warning which tells id of detected NANDEnrico Scholz2008-09-011-1/+4
| | | | | | | Minor patch to help debugging of NAND detection. Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] pxa3xx_nand: moved some helper variables out from platform dataEnrico Scholz2008-09-012-26/+26
| | | | | | | | | This patch moves some attributes out from the platform data into the dynamically created nand device. This results into a cleaner interface and allows to use constant pxa3xx_nand_flash definitions. Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] pxa3xx_nand: added some 'const' annotations to the exported APIEnrico Scholz2008-09-012-9/+9
| | | | | | | | | This patch marks some attributes as 'const' which are set only once and never be modified by the driver. There are some changes in parameter list and variable declarations too which mark them as 'const'. Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] pxa3xx_nand: allow to disable builtin flash-type tableEnrico Scholz2008-09-012-0/+11
| | | | | | | | | This patch adds a MTD_NAND_PXA3xx_BUILTIN configuration variables which allows to disable usage of builtin flash-type table. Not enabling this option saves some space in the generated driver. Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] pxa3xx_nand: allow to define flash types in the platform dataEnrico Scholz2008-09-012-2/+19
| | | | | | | | | | This patch adds 'flash' and 'num_flash' attributes to the platform data. There was added code in the driver to iterate across these attributes in the detect-flash routine. This is done similarly to the existing method which uses a 'builtin_flash_types' field. Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] pxa3xx_nand: moved nand definitions into shared platform headerEnrico Scholz2008-09-012-44/+44
| | | | | | | | | | | | | | | | | | | | | | | | This patch moves the exported datastructures from the pxa3xx_nand.c driver into the <mach/pxa3xx_nand.h> header. This is a plain movement without any modification of the attributes. This is the first one of a set of patches which: * allows to specify used NAND flash in the platform code and allows to turn off the old way to specify NAND characteristics in the driver. This way did not worked well as these characteristics depend on the platform and can not be derived from NAND id alone. E.g. some NAND chips share the same ID (e.g. K9K8G08U0A and K9NBG08U5A) but have different timings (which are written in the common driver currently and must be modified there). * adds 'const' annotations at various places Further patches will be sent to the mtd-list. Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NOR] Select MTD_CFI_UTIL when MTD_CFI probe routine is enabledDavid Woodhouse2008-09-011-0/+1
| | | | | | | | It requires cfi_qry_mode_on(), which is in cfi_util.c Reported by Russell King Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* [MTD] [NAND] pxa3xx_nand_flash: Add definition of STM2GbX16 NAND flashesSemun Lee2008-09-011-0/+23
| | | | | | Signed-off-by: Semun Lee <semun.lee@samsung.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* CRED: Wrap task credential accesses in the JFFS2 filesystemDavid Howells2008-09-011-2/+2
| | | | | | | | | | | | | | | | Wrap access to task credentials so that they can be separated more easily from the task_struct during the introduction of COW creds. Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id(). Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more sense to use RCU directly rather than a convenient wrapper; these will be addressed by later patches. Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: James Morris <jmorris@namei.org> Acked-by: Serge Hallyn <serue@us.ibm.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Merge branch 'master' of ↵David Woodhouse2008-09-011758-19102/+61067
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
| * Resource handling: add 'insert_resource_expand_to_fit()' functionLinus Torvalds2008-08-302-25/+64
| | | | | | | | | | | | | | | | | | Not used anywhere yet, but this complements the existing plain 'insert_resource()' functionality with a version that can expand the resource we are adding in order to fix up any conflicts it has with existing resources. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * Merge branch 'for-linus' of ↵Linus Torvalds2008-08-293-1/+8
| |\ | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ALSA: oxygen: fix distorted output on AK4396-based cards Revert "ALSA: hda - Added model selection for iMac 24""
| | * ALSA: oxygen: fix distorted output on AK4396-based cardsClemens Ladisch2008-08-292-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When changing the sample rate, the CMI8788's master clock output becomes unstable for a short time. The AK4396 needs the master clock to do SPI writes, so writing to an AK4396 control register directly after a sample rate change will garble the value. In our case, this leads to the DACs being misconfigured to I2S sample format, which results in a wrong output level and horrible distortions on samples louder than -6 dB. To fix this, we need to wait until the new master clock signal has become stable before doing SPI writes. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
| | * Revert "ALSA: hda - Added model selection for iMac 24""Takashi Iwai2008-08-271-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 3e0e469fa216ec70c93b1593821b759d19ee2e6b. The patch introduced a wrong detection of other intel Macs with ALC88* codec because they share the same PCI SSID (but have different codec subsystem-IDs). See http://lkml.org/lkml/2008/8/24/143 Reported-and-tested-by: Guillaume Chazarain <guichaz@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
| * | Don't trigger softlockup detector on network fs blocked tasksAndi Kleen2008-08-291-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pulling the ethernet cable on a 2.6.27-rc system with NFS mounts currently leads to an ongoing flood of soft lockup detector backtraces for all tasks blocked on the NFS mounts when the hickup takes longer than 120s. I don't think NFS problems should be all that noisy. Luckily there's a reasonably easy way to distingush this case. Don't report task softlockup warnings for tasks in TASK_KILLABLE state, which is used by the network file systems. I believe this patch is a 2.6.27 candidate. Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | Revert "x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against ↵Linus Torvalds2008-08-291-78/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BAR, v3" This reverts commit a2bd7274b47124d2fc4dfdb8c0591f545ba749dd. It wasn't really right to begin with (there's a better fix for the problem with e820 reservations clashing with PCI BAR's pending), but it also actually causes more regressions, so it should be reverted even before the better fix is finalized. Rafael reports that this commit broke AHCI detection, and thus causes the kernel to not boot on his quad core test box. Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Yinghai Lu <yhlu.kernel@gmail.com> Cc: David Witbrodt <dawitbro@sbcglobal.net> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | Linux 2.6.27-rc5v2.6.27-rc5Linus Torvalds2008-08-291-1/+1
| | |
| * | Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds2008-08-2841-313/+17518
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 5226/1: remove unmatched comment end. [ARM] Skip memory holes in FLATMEM when reading /proc/pagetypeinfo [ARM] use bcd2bin/bin2bcd [ARM] use the new byteorder headers [ARM] OMAP: Fix 2430 SMC91x ethernet IRQ [ARM] OMAP: Add and update OMAP default configuration files [ARM] OMAP: Change mailing list for OMAP in MAINTAINERS [ARM] S3C2443: Fix the S3C2443 clock register definitions [ARM] JIVE: Fix the spi bus numbering [ARM] S3C24XX: pwm.c: stop debugging output [ARM] S3C24XX: Fix sparse warnings in pwm.c [ARM] S3C24XX: Fix spare errors in pwm-clock driver [ARM] S3C24XX: Fix sparse warnings in arch/arm/plat-s3c24xx/gpiolib.c [ARM] S3C24XX: Fix nor-simtec driver sparse errors [ARM] 5225/1: zaurus: Register I2C controller for audio codecs [ARM] orion5x: update defconfig to v2.6.27-rc4 [ARM] Orion: register UART1 on QNAP TS-209 and TS-409 [ARM] Orion: activate lm75 driver on DNS-323 [ARM] Orion: fix MAC detection on QNAP TS-209 and TS-409 [ARM] Orion: Fix boot crash on Kurobox Pro
| | * | [ARM] 5226/1: remove unmatched comment end.Jean-Christophe DUBOIS2008-08-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | remove unmatched comment end. Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | Merge branch 'omap-rmk'Russell King2008-08-2820-220/+17310
| | |\ \
| | | * | [ARM] OMAP: Fix 2430 SMC91x ethernet IRQRussell King2008-08-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Taken from omap 97b705ad835f1481270c4b67b402d6e37fa8ad15: ARM: OMAP: Misc compile fixes after syncing with mainline Also fix 2430 smc91x to use IRQ_LOWLEVEL. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | | * | [ARM] OMAP: Add and update OMAP default configuration filesRussell King2008-08-2718-218/+17308
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update omap_h2_1610 and omap_osk_5912 default configurations. Add ams delta, n770, omap 2430sdp, apollon_2420, generic 1510, 1610, 1710, 2420, h4 2420, innovator 1510 and 1610, perseus2 730, palte, palmtt, palmz71 and sx1 default configurations. Pulled out of the omap zoom tree. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | | * | [ARM] OMAP: Change mailing list for OMAP in MAINTAINERSDirk Behme2008-08-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OMAP has now a list at vger. Signed-off-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | | [ARM] Skip memory holes in FLATMEM when reading /proc/pagetypeinfoMel Gorman2008-08-272-1/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ordinarily, memory holes in flatmem still have a valid memmap and is safe to use. However, an architecture (ARM) frees up the memmap backing memory holes on the assumption it is never used. /proc/pagetypeinfo reads the whole range of pages in a zone believing that the memmap is valid and that pfn_valid will return false if it is not. On ARM, freeing the memmap breaks the page->zone linkages even though pfn_valid() returns true and the kernel can oops shortly afterwards due to accessing a bogus struct zone *. This patch lets architectures say when FLATMEM can have holes in the memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo will confirm that the page linkages are still valid by checking page->zone is still the expected zone. The lookup of page_zone is safe as there is a limited range of memory that is accessed when calling page_zone. Even if page_zone happens to return the correct zone, the impact is that the counters in /proc/pagetypeinfo are slightly off but fragmentation monitoring is unlikely to be relevant on an embedded system. Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Mel Gorman <mel@csn.ul.ie> Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | | [ARM] use bcd2bin/bin2bcdAdrian Bunk2008-08-271-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch changes arm to use the new bcd2bin/bin2bcd functions instead of the obsolete BCD_TO_BIN/BIN_TO_BCD macros. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | | [ARM] use the new byteorder headersHarvey Harrison2008-08-271-14/+11
| | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | | Merge branch 'for-rmk' of git://git.marvell.com/orionRussell King2008-08-277-50/+138
| | |\ \ \
| | | * | | [ARM] orion5x: update defconfig to v2.6.27-rc4Nicolas Pitre2008-08-221-32/+112
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Nicolas Pitre <nico@marvell.com>
| | | * | | [ARM] Orion: register UART1 on QNAP TS-209 and TS-409Martin Michlmayr2008-08-222-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Register UART1 on QNAP TS-209 and TS-409 because the PIC controller is connected to it. This fixes a regression from 2.6.26. Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
| | | * | | [ARM] Orion: activate lm75 driver on DNS-323Martin Michlmayr2008-08-222-6/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The lm75 driver was recently converted to the new-style binding, so now it can be loaded from the DNS-323 support code. Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Tested-by: Tobias Poschwatta <tp@fonz.de> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
| | | * | | [ARM] Orion: fix MAC detection on QNAP TS-209 and TS-409Martin Michlmayr2008-08-222-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Flash needs to be set up before we can try to read the MAC address from there. Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
| | | * | | [ARM] Orion: Fix boot crash on Kurobox ProPer Andersson2008-08-223-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kurobox Pro crashes when any of the PCI controller registers are accessed. This patch adds a function to the Orion PCI handling code that board support code can call to disable enumerating the PCI bus entirely, and makes the Kurobox Pro PCI-related init code call this function. Signed-off-by: Per Andersson <avtobiff@gmail.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
| | * | | | Merge branch 's3c2410' of git://aeryn.fluff.org.uk/bjdooks/linux.gitRussell King2008-08-276-18/+20
| | |\ \ \ \
| | | * | | | [ARM] S3C2443: Fix the S3C2443 clock register definitionsWei Shuai2008-08-261-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the S3C2443 clock register definitions for selecting the EPLL reference clock described by S3C2443_CLKSRC_EPLLREF. Signed-off-by: Wei Shuai <cpuwolf@gmail.com> [ben-linux@fluff.org: minor description fixes] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | * | | | [ARM] JIVE: Fix the spi bus numberingBen Dooks2008-08-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The first spi bus is registered with number 0, but the board data says that the device on it is registered on bus 1. Move the spi bus to bus 1 to keep the compatibility with the original board-support patches. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | * | | | [ARM] S3C24XX: pwm.c: stop debugging outputBen Dooks2008-08-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move debugging output to dev_dbg() instead of dev_info(). Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | * | | | [ARM] S3C24XX: Fix sparse warnings in pwm.cBen Dooks2008-08-261-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm.c: warning: symbol 's3c_device_timer' was not declared. Should it be static? warning: symbol 'pwm_calc_tin' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | * | | | [ARM] S3C24XX: Fix spare errors in pwm-clock driverBen Dooks2008-08-261-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm-clock.c: warning: symbol 'clk_timer_scaler' was not declared. Should it be static? warning: symbol 'clk_timer_tclk' was not declared. Should it be static? warning: symbol 'clk_timer_tdiv' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben-linux@fluff.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-26 00:14:32 +0100