| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\ |
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().
If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.
This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.
This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull networking fixes from David Miller:
1) Fix dumping of nft_quota entries, from Pablo Neira Ayuso.
2) Fix out of bounds access in nf_tables discovered by KASAN, from
Florian Westphal.
3) Fix IRQ enabling in dp83867 driver, from Grygorii Strashko.
4) Fix unicast filtering in be2net driver, from Ivan Vecera.
5) tg3_get_stats64() can race with driver close and ethtool
reconfigurations, fix from Michael Chan.
6) Fix error handling when pass limit is reached in bpf code gen on
x86. From Daniel Borkmann.
7) Don't clobber switch ops and use proper MDIO nested reads and writes
in bcm_sf2 driver, from Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
net: dsa: bcm_sf2: Utilize nested MDIO read/write
net: dsa: bcm_sf2: Do not clobber b53_switch_ops
net: stmmac: fix maxmtu assignment to be within valid range
bpf: change back to orig prog on too many passes
tg3: Fix race condition in tg3_get_stats64().
be2net: fix unicast list filling
be2net: fix accesses to unicast list
netlabel: add CALIPSO to the list of built-in protocols
vti6: fix device register to report IFLA_INFO_KIND
net: phy: dp83867: fix irq generation
amd-xgbe: Fix IRQ processing when running in single IRQ mode
sh_eth: R8A7740 supports packet shecksumming
sh_eth: fix EESIPR values for SH77{34|63}
r8169: fix the typo in the comment
nl80211: fix sched scan netlink socket owner destruction
bridge: netfilter: Fix dropping packets that moving through bridge interface
netfilter: ipt_CLUSTERIP: check duplicate config when initializing
netfilter: nft_payload: mangle ckecksum if NFT_PAYLOAD_L4CSUM_PSEUDOHDR is set
netfilter: nf_tables: fix oob access
netfilter: nft_queue: use raw_smp_processor_id()
...
|
| | | |\
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Couple fixes
Here are a couple of fixes for bcm_sf2, please queue these up for -stable
as well, thank you very much!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
There is no checking valid value of maxmtu when getting it from
device tree. This resolution added the checking condition to
ensure the assignment is made within a valid range.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes: 959a75791603 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations. Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block. tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: b717241 be2net: replace polling with sleeping in the FW completion path
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Commit 988d44b "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 988d44b be2net: Avoid redundant addition of mac address in HW
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When we added CALIPSO support in Linux v4.8 we forgot to add it to the
list of supported protocols with display at boot.
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |\
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another single fix, to correctly handle destruction of a
single netlink socket having ownership of multiple objects
(scheduled scan requests and interfaces.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
A single netlink socket might own multiple interfaces *and* a
scheduled scan request (which might belong to another interface),
so when it goes away both may need to be destroyed.
Remove the schedule_scan_stop indirection to fix this - it's only
needed for interface destruction because of the way this works
right now, with a single work taking care of all interfaces.
Cc: stable@vger.kernel.org
Fixes: 93a1e86ce10e4 ("nl80211: Stop scheduled scan if netlink client disappears")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When running in single IRQ mode, the additional IRQ routines were being
skipped because only the XGMAC interrupt status was being checked.
Update the code so that the additional IRQ routines are checked whenever
an interrupt is received.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data, thus CSMR isn't cleared...
Fixes: 73a0d907301e ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
As the SH77{34|63} manuals are freely available, I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.
Fixes: 380af9e390ec ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"")
Fixes: f5d12767c8fd ("sh_eth: get SH77{34|63} support out of #ifdef")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |\ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains accumulated Netfilter fixes for your
net tree:
1) Ensure quota dump and reset happens iff we can deliver numbers to
userspace.
2) Silence splat on incorrect use of smp_processor_id() from nft_queue.
3) Fix an out-of-bound access reported by KASAN in
nf_tables_rule_destroy(), patch from Florian Westphal.
4) Fix layer 4 checksum mangling in the nf_tables payload expression
with IPv6.
5) Fix a race in the CLUSTERIP target from control plane path when two
threads run to add a new configuration object. Serialize invocations
of clusterip_config_init() using spin_lock. From Xin Long.
6) Call br_nf_pre_routing_finish_bridge_finish() once we are done with
the br_nf_pre_routing_finish() hook. From Artur Molchanov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Problem:
br_nf_pre_routing_finish() calls itself instead of
br_nf_pre_routing_finish_bridge(). Due to this bug reverse path filter drops
packets that go through bridge interface.
User impact:
Local docker containers with bridge network can not communicate with each
other.
Fixes: c5136b15ea36 ("netfilter: bridge: add and use br_nf_hook_thresh")
Signed-off-by: Artur Molchanov <artur.molchanov@synesis.ru>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Now when adding an ipt_CLUSTERIP rule, it only checks duplicate config in
clusterip_config_find_get(). But after that, there may be still another
thread to insert a config with the same ip, then it leaves proc_create_data
to do duplicate check.
It's more reasonable to check duplicate config by ipt_CLUSTERIP itself,
instead of checking it by proc fs duplicate file check. Before, when proc
fs allowed duplicate name files in a directory, It could even crash kernel
because of use-after-free.
This patch is to check duplicate config under the protection of clusterip
net lock when initializing a new config and correct the return err.
Note that it also moves proc file node creation after adding new config, as
proc_create_data may sleep, it couldn't be called under the clusterip_net
lock. clusterip_config_find_get returns NULL if c->pde is null to make sure
it can't be used until the proc file node creation is done.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
If the NFT_PAYLOAD_L4CSUM_PSEUDOHDR flag is set, then mangle layer 4
checksum. This should not depend on csum_type NFT_PAYLOAD_CSUM_INET
since IPv6 header has no checksum field, but still an update of any of
the pseudoheader fields may trigger a layer 4 checksum update.
Fixes: 1814096980bb ("netfilter: nft_payload: layer 4 checksum adjustment for pseudoheader fields")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
BUG: KASAN: slab-out-of-bounds in nf_tables_rule_destroy+0xf1/0x130 at addr ffff88006a4c35c8
Read of size 8 by task nft/1607
When we've destroyed last valid expr, nft_expr_next() returns an invalid expr.
We must not dereference it unless it passes != nft_expr_last() check.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Using smp_processor_id() causes splats with PREEMPT_RCU:
[19379.552780] BUG: using smp_processor_id() in preemptible [00000000] code: ping/32389
[19379.552793] caller is debug_smp_processor_id+0x17/0x19
[...]
[19379.552823] Call Trace:
[19379.552832] [<ffffffff81274e9e>] dump_stack+0x67/0x90
[19379.552837] [<ffffffff8129a4d4>] check_preemption_disabled+0xe5/0xf5
[19379.552842] [<ffffffff8129a4fb>] debug_smp_processor_id+0x17/0x19
[19379.552849] [<ffffffffa07c42dd>] nft_queue_eval+0x35/0x20c [nft_queue]
No need to disable preemption since we only fetch the numeric value, so
let's use raw_smp_processor_id() instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Dumping of netlink attributes may fail due to insufficient room in the
skbuff, so let's reset consumed quota if we succeed to put netlink
attributes into the skbuff.
Fixes: 43da04a593d8 ("netfilter: nf_tables: atomic dump and reset for stateful objects")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
>From the realtek data sheet, the PID0 should be bit 0.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 4.10-rc3. Yeah, it's a lot, an
artifact of the holiday break I think.
Lots of gadget and the usual XHCI fixups for reported issues (one day
that driver will calm down...) Also included are a bunch of usb-serial
driver fixes, and for good measure, a number of much-reported MUSB
driver issues have finally been resolved.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (72 commits)
USB: fix problems with duplicate endpoint addresses
usb: ohci-at91: use descriptor-based gpio APIs correctly
usb: storage: unusual_uas: Add JMicron JMS56x to unusual device
usb: hub: Move hub_port_disable() to fix warning if PM is disabled
usb: musb: blackfin: add bfin_fifo_offset in bfin_ops
usb: musb: fix compilation warning on unused function
usb: musb: Fix trying to free already-free IRQ 4
usb: musb: dsps: implement clear_ep_rxintr() callback
usb: musb: core: add clear_ep_rxintr() to musb_platform_ops
USB: serial: ti_usb_3410_5052: fix NULL-deref at open
USB: serial: spcp8x5: fix NULL-deref at open
USB: serial: quatech2: fix sleep-while-atomic in close
USB: serial: pl2303: fix NULL-deref at open
USB: serial: oti6858: fix NULL-deref at open
USB: serial: omninet: fix NULL-derefs at open and disconnect
USB: serial: mos7840: fix misleading interrupt-URB comment
USB: serial: mos7840: remove unused write URB
USB: serial: mos7840: fix NULL-deref at open
USB: serial: mos7720: remove obsolete port initialisation
USB: serial: mos7720: fix parallel probe
...
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179
[<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542
[<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
[<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
[<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
[< inline >] create_dir lib/kobject.c:71
[<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
[< inline >] kobject_add_varg lib/kobject.c:366
[<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411
[<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088
[<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206
[<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
[<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
[<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
[<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
[<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263
This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.
WTF? Big sigh.
Fixes: 054d4b7b577d ("usb: ohci-at91: Use descriptor-based gpio APIs")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This device gives the following error on detection.
xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or
incorrect stream ring
The same error is not seen when it is added to unusual_device
list with US_FL_NO_REPORT_OPCODES passed.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Oliver Neukum <oneukun@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Fixes: 37be66767e3cae4f ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes: cc92f6818f6e ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When unloading omap2430, we can get the following splat:
WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...
This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.
Fixes: 6995eb68aab7 ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.
Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |\ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.10-rc3
These fixes address a number of long-standing issues in various
USB-serial drivers which would lead to crashes should a malicious device
lack the expected endpoints.
Included are also a few related fixes, and a couple of unrelated ones
that were found during my survey (e.g. a memleak and a
sleep-while-atomic).
A compiler warning revealed an error-handling issue in the new f81534
driver which is also fixed.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fix NULL-pointer dereference in open() should a malicious device lack
the expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
..
[<bf06a6b0>] (ti_open [ti_usb_3410_5052]) from [<bf02e118>] (serial_port_activate+0x68/0x98 [usbserial])
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at spcp8x5_open+0x30/0xd0 [spcp8x5]
Fixes: 619a6f1d1423 ("USB: add usb-serial spcp8x5 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The write URB was being killed using the synchronous interface while
holding a spin lock in close().
Simply drop the lock and busy-flag update, something which would have
been taken care of by the completion handler if the URB was in flight.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fix NULL-pointer dereference in open() should a type-0 or type-1 device
lack the expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at pl2303_open+0x38/0xec [pl2303]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at oti6858_open+0x30/0x1d0 [oti6858]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 49cdee0ed0fc ("USB: oti6858 usb-serial driver (in Nokia CA-42
cable)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fix NULL-pointer dereferences at open() and disconnect() should the
device lack the expected bulk-out endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 000000b4
...
[c0170ff0>] (__lock_acquire) from [<c0172f00>] (lock_acquire+0x108/0x264)
[<c0172f00>] (lock_acquire) from [<c06a5090>] (_raw_spin_lock_irqsave+0x58/0x6c)
[<c06a5090>] (_raw_spin_lock_irqsave) from [<c0470684>] (tty_port_tty_set+0x28/0xa4)
[<c0470684>] (tty_port_tty_set) from [<bf08d384>] (omninet_open+0x30/0x40 [omninet])
[<bf08d384>] (omninet_open [omninet]) from [<bf07c118>] (serial_port_activate+0x68/0x98 [usbserial])
Unable to handle kernel NULL pointer dereference at virtual address 00000234
...
[<bf01f418>] (omninet_disconnect [omninet]) from [<bf0016c0>] (usb_serial_disconnect+0xe4/0x100 [usbserial])
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The interrupt URB is killed at final port close since commit
0de9a7024e7a ("USB: overhaul of mos7840 driver").
Fixes: 0de9a7024e7a ("USB: overhaul of mos7840 driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Remove code to manage a write URB that was never allocated.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at mos7840_open+0x88/0x8dc [mos7840]
Note that we continue to treat the interrupt-in endpoint as optional for
now.
Fixes: 3f5429746d91 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Since commit b69578df7e98 ("USB: usbserial: mos7720: add support for
parallel port on moschip 7715"), the interrupt urb is no longer
submitted at first port open and the endpoint-address initialisation at
port-probe is no longer used.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
A static usb-serial-driver structure that is used to initialise the
interrupt URB was modified during probe depending on the currently
probed device type, something which could break a parallel probe of a
device of a different type.
Fix this up by overriding the default completion callback for MCS7715
devices in attach() instead. We may want to use two usb-serial driver
instances for the two types later.
Fixes: fb088e335d78 ("USB: serial: add support for serial port on the
moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
