summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* GPIO: add bindings for managed devicesJohn Crispin2012-01-043-1/+95
| | | | | | | | This patch adds 2 functions that allow managed devices to request GPIOs. These GPIOs will then be managed by drivers/base/devres.c. Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* GPIO/pl061: Add suspend resume capabilityDeepak Sikri2012-01-041-0/+68
| | | | | | | | | | | | | This patch adds the suspend and resume operations in the driver. The patch ensures the data save and restore for the device registers during the suspend and resume operations respectively. Signed-off-by: Deepak Sikri <deepak.sikri@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* drivers/gpio/gpio-tegra.c: use devm_request_and_ioremapJulia Lawall2012-01-021-8/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reimplement a call to devm_request_mem_region followed by a call to ioremap or ioremap_nocache by a call to devm_request_and_ioremap. The semantic patch that makes this transformation is as follows: (http://coccinelle.lip6.fr/) // <smpl> @nm@ expression myname; identifier i; @@ struct platform_driver i = { .driver = { .name = myname } }; @@ expression dev,res,size; expression nm.myname; @@ -if (!devm_request_mem_region(dev, res->start, size, - \(res->name\|dev_name(dev)\|myname\))) { - ... - return ...; -} ... when != res->start ( -devm_ioremap(dev,res->start,size) +devm_request_and_ioremap(dev,res) | -devm_ioremap_nocache(dev,res->start,size) +devm_request_and_ioremap(dev,res) ) ... when any when != res->start // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* gpio: Add decode of WM8994 GPIO configurationMark Brown2012-01-021-2/+77
| | | | | | | | For the human reader. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* gpio: Convert GPIO drivers to module_platform_driverMark Brown2012-01-0211-128/+11
| | | | | | | | | Where appropriate factor out some boilerplate code for platform device registration into module_platform_driver. Drivers that don't use the standard module_init initcall haven't been converted. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* gpio: Fix typo in comment in Samsung driverMark Brown2012-01-021-1/+1
| | | | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* gpio: Explicitly index samsung_gpio_cfgsMark Brown2012-01-021-10/+19
| | | | | | | | | | | Make it easier to follow the by number references into samsung_gpio_cfgs by putting the indexes into the code initialising the array, improving readability a bit. Ideally we wouldn't be using magic array indexes at all but this is easier than coming up with a better way. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* Merge branch 'pl022' of ↵Grant Likely2011-12-132-56/+89
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into gpio/next
| * spi/pl022: make the chip deselect handling thread safeVirupax Sadashivpetimath2011-12-011-35/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is a possibility that the pump_message and giveback run in parallel on a SMP system. Both the pump_message and giveback threads work on the same SPI message queue. Results will be in correct if the pump_message gets to work on the queue first. when the pump_message works with the queue, it reads the head of the queue and removes it from the queue. pump_message activates the chip select depending on this message read. This leads to giveback working on the modified queue or a emptied queue. If the queue is empty or if the next message on the queue (which is not the actual next message, as the pump message has removed the next message from the queue) is not for the same SPI device as that Of the previous one, giveback will de-activate the chip select activated by pump_message(), which is wrong. To solve this problem pump_message is made not to run and access the queue until the giveback is done handling the queue. I.e. by making the cur_msg NULL after the giveback has read the queue. Also a state variable has been introduced to keep track of when the CS for next message is already activated and avoid to double-activate it. Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * spi/pl022: add support for pm_runtime autosuspendChris Blair2011-12-012-2/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for configuring the spi bus to use autosuspend for runtime power management. This can reduce the latency in starting an spi transfer by not suspending the device immediately following completion of a transfer. If another transfer then takes place before the autosuspend timeout, the call to resume the device can return immediately rather than needing to risk sleeping in order to resume the device. Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Chris Blair <chris.blair@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * spi/pl022: disable the PL022 block when unusedVirupax Sadashivpetimath2011-12-011-1/+5
| | | | | | | | | | | | | | | | | | Make sure we clear the enable bit when the block is not used. This will save some energy in certain hardware versions. Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * spi/pl022: move device disable to workqueue threadChris Blair2011-12-011-9/+16
| | | | | | | | | | | | | | | | | | | | | | Moves the disabling of the device and clocks to the same thread in which the device and clocks are enabled. This avoids SMP issues where the device can be enabled for a transfer by one thread and then disabled by the completion of the previous transfer in another thread. Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Chris Blair <chris.blair@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * spi/pl022: skip default configuration before suspendingVirupax Sadashivpetimath2011-12-011-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | The loading of the default configuration before suspending has been in the driver since its inception, but it is not really needed. Especially so since we take to all the trouble of enabling and disabling power and clock just to do this. Let's scrap this now. Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * spi/pl022: fix build warningsJonas Aaberg2011-12-011-1/+1
| | | | | | | | | | | | | | | | | | The driver build complains with newer compilers unless you initialize this struct properly. Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * spi/pl022: only enable RX interrupts when TX is completeChris Blair2011-12-011-5/+10
| | | | | | | | | | | | | | | | | | | | For interrupt mode transfers, start with only TX interrupts enabled to reduce the overall number of interrupts received. Once TX is complete, enable RX interrupts to complete the transfer. Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Chris Blair <chris.blair@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpio: Add Linus Walleij as gpio co-maintainerGrant Likely2011-12-131-0/+1
| | | | | | | | | | Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Linus Walleij <linus.walleij@linaro.org>
* | of: Add device tree selftestsGrant Likely2011-12-126-0/+189
| | | | | | | | | | | | | | | | | | Add some runtime test cases for the library of device tree parsing functions. v2: - Add testcase for phandle with 0 args - Don't run testcases if testcase data isn't present in device tree Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | of: create of_phandle_args to simplify return of phandle parsing dataGrant Likely2011-12-125-103/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | of_parse_phandle_with_args() needs to return quite a bit of data. Rather than making each datum a separate **out_ argument, this patch creates struct of_phandle_args to contain all the returned data and reworks the user of the function. This patch also enables of_parse_phandle_with_args() to return the device node pointer for the phandle node. This patch also ends up being fairly major surgery to of_parse_handle_with_args(). The existing structure didn't work well when extending to use of_phandle_args, and I discovered bugs during testing. I also took the opportunity to rename the function to be like the existing of_parse_phandle(). v2: - moved declaration of of_phandle_args to fix compile on non-DT builds - fixed incorrect index in example usage - fixed incorrect return code handling for empty entries Reviewed-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()Grant Likely2011-12-123-35/+10
| | | | | | | | | | | | | | | | | | | | | | | | A large chunk of qe_pin_request() is unnecessarily cut-and-paste directly from of_get_named_gpio_flags(). This patch cuts out the duplicate code and replaces it with a call to of_get_gpio(). v2: fixed compile error due to missing gpio_to_chip() Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org>
* | gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()Grant Likely2011-12-121-41/+2
| | | | | | | | | | | | | | | | | | of_reset_gpio_handle() is largely a cut-and-paste copy of of_get_named_gpio_flags(). There really isn't any reason for the split, so this patch deletes the duplicate function Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Michal Simek <monstr@monstr.eu>
* | gpiolib: output basic details and consolidate gpio device driversGrant Likely2011-12-129-18/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a kernel message, containing GPIO range and device name on successful device registration, and removes duplicate messages from the following drivers: * gpio-adp5588 * gpio-bt8xx * gpio-cs5535 * gpio-janz-ttl * gpio-nomadik * gpio-pcf857x * gpio-xilinx * drivers/of/gpio.c Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> [grant.likely@secretlab.ca: squashed 2 patches together] Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS SemiconductorTomoya MORINAGA2011-12-121-3/+3
| | | | | | | | | | | | | | | | On October 1 in 2011, OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | pch_gpio: Support new device LAPIS Semiconductor ML7831 IOHTomoya MORINAGA2011-12-122-5/+7
| | | | | | | | | | | | | | ML7831 is companion chip for Intel Atom E6xx series. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | Linux 3.2-rc5v3.2-rc5Linus Torvalds2011-12-101-1/+1
| |
* | Merge git://git.samba.org/sfrench/cifs-2.6Linus Torvalds2011-12-094-5/+39
|\ \ | | | | | | | | | | | | | | | | | | | | | * git://git.samba.org/sfrench/cifs-2.6: cifs: check for NULL last_entry before calling cifs_save_resume_key cifs: attempt to freeze while looping on a receive attempt cifs: Fix sparse warning when calling cifs_strtoUCS CIFS: Add descriptions to the brlock cache functions
| * | cifs: check for NULL last_entry before calling cifs_save_resume_keyJeff Layton2011-12-091-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Prior to commit eaf35b1, cifs_save_resume_key had some NULL pointer checks at the top. It turns out that at least one of those NULL pointer checks is needed after all. When the LastNameOffset in a FIND reply appears to be beyond the end of the buffer, CIFSFindFirst and CIFSFindNext will set srch_inf.last_entry to NULL. Since eaf35b1, the code will now oops in this situation. Fix this by having the callers check for a NULL last entry pointer before calling cifs_save_resume_key. No change is needed for the call site in cifs_readdir as it's not reachable with a NULL current_entry pointer. This should fix: https://bugzilla.redhat.com/show_bug.cgi?id=750247 Cc: stable@vger.kernel.org Cc: Christoph Hellwig <hch@infradead.org> Reported-by: Adam G. Metzler <adamgmetzler@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
| * | cifs: attempt to freeze while looping on a receive attemptJeff Layton2011-12-091-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the recent overhaul of the demultiplex thread receive path, I neglected to ensure that we attempt to freeze on each pass through the receive loop. Reported-and-Tested-by: Woody Suwalski <terraluna977@gmail.com> Reported-and-Tested-by: Adam Williamson <awilliam@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
| * | cifs: Fix sparse warning when calling cifs_strtoUCSSteve French2011-12-091-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix sparse endian check warning while calling cifs_strtoUCS CHECK fs/cifs/smbencrypt.c fs/cifs/smbencrypt.c:216:37: warning: incorrect type in argument 1 (different base types) fs/cifs/smbencrypt.c:216:37: expected restricted __le16 [usertype] *<noident> fs/cifs/smbencrypt.c:216:37: got unsigned short *<noident> Signed-off-by: Steve French <smfrench@gmail.com> Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com
| * | CIFS: Add descriptions to the brlock cache functionsPavel Shilovsky2011-12-091-0/+26
| | | | | | | | | | | | | | | Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <sfrench@us.ibm.com>
* | | Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds2011-12-098-44/+68
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, efi: Calling __pa() with an ioremap()ed address is invalid x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked x86/intel_mid: Kconfig select fix x86/intel_mid: Fix the Kconfig for MID selection
| * | | x86, efi: Calling __pa() with an ioremap()ed address is invalidMatt Fleming2011-12-096-35/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set in ->attribute we currently call set_memory_uc(), which in turn calls __pa() on a potentially ioremap'd address. On CONFIG_X86_32 this is invalid, resulting in the following oops on some machines: BUG: unable to handle kernel paging request at f7f22280 IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210 [...] Call Trace: [<c104f8ca>] ? page_is_ram+0x1a/0x40 [<c1025aff>] reserve_memtype+0xdf/0x2f0 [<c1024dc9>] set_memory_uc+0x49/0xa0 [<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa [<c19216d4>] start_kernel+0x291/0x2f2 [<c19211c7>] ? loglevel+0x1b/0x1b [<c19210bf>] i386_start_kernel+0xbf/0xc8 A better approach to this problem is to map the memory region with the correct attributes from the start, instead of modifying it after the fact. The uncached case can be handled by ioremap_nocache() and the cached by ioremap_cache(). Despite first impressions, it's not possible to use ioremap_cache() to map all cached memory regions on CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really don't like being mapped into the vmalloc space, as detailed in the following bug report, https://bugzilla.redhat.com/show_bug.cgi?id=748516 Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA regions are covered by the direct kernel mapping table on CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI regions via the direct kernel mapping with the initial call to init_memory_mapping() in setup_arch(), whereas previously these regions wouldn't be mapped if they were after the last E820_RAM region until efi_ioremap() was called. Doing it this way allows us to delete efi_ioremap() completely. Signed-off-by: Matt Fleming <matt.fleming@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Matthew Garrett <mjg@redhat.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Huang Ying <huang.ying.caritas@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
| * | | x86, hpet: Immediately disable HPET timer 1 if rtc irq is maskedMark Langsdorf2011-12-081-7/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When HPET is operating in RTC mode, the TN_ENABLE bit on timer1 controls whether the HPET or the RTC delivers interrupts to irq8. When the system goes into suspend, the RTC driver sends a signal to the HPET driver so that the HPET releases control of irq8, allowing the RTC to wake the system from suspend. The switchover is accomplished by a write to the HPET configuration registers which currently only occurs while servicing the HPET interrupt. On some systems, I have seen the system suspend before an HPET interrupt occurs, preventing the write to the HPET configuration register and leaving the HPET in control of the irq8. As the HPET is not active during suspend, it does not generate a wake signal and RTC alarms do not work. This patch forces the HPET driver to immediately transfer control of the irq8 channel to the RTC instead of waiting until the next interrupt event. Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com> Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.com Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org
| * | | x86/intel_mid: Kconfig select fixAlan Cox2011-12-061-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If we select a symbol it should have a type declared first otherwise in some situations the config tools get upset. They are currently perhaps a bit too resilient which is why this wasn't noticed initially. Signed-off-by: Alan Cox <alan@linux.intel.com> Link: http://lkml.kernel.org/r/20111206132811.4041.32549.stgit@bob.linux.org.uk Signed-off-by: Ingo Molnar <mingo@elte.hu>
| * | | x86/intel_mid: Fix the Kconfig for MID selectionAlan Cox2011-12-061-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently fail to build on CONFIG_X86_INTEL_MID=y and CONFIG_X86_MRST unset. We could build all the bits to make generic MID work if you picked MID platform alone but that's really silly. Instead use select and two variables. This looks a bit daft right now but once we add a Medfield selection it'll start to look a good deal more sensible. Reported-by: Ingo Molnar <mingo@elte.hu> Reported-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Link: http://lkml.kernel.org/r/20111205231433.28811.51297.stgit@bob.linux.org.uk Signed-off-by: Ingo Molnar <mingo@elte.hu>
* | | | Merge branch 'spi/for-3.2' of git://git.pengutronix.de/git/wsa/linux-2.6Linus Torvalds2011-12-094-4/+6
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'spi/for-3.2' of git://git.pengutronix.de/git/wsa/linux-2.6: spi/gpio: fix section mismatch warning spi/fsl-espi: disable CONFIG_SPI_FSL_ESPI=m build spi/nuc900: Include linux/module.h spi/ath79: fix compile error due to missing include
| * | | | spi/gpio: fix section mismatch warningManuel Lauss2011-12-071-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes: The function __devinit spi_gpio_probe() references a function __init spi_gpio_alloc.isra.4(). If spi_gpio_alloc.isra.4 is only used by spi_gpio_probe then annotate spi_gpio_alloc.isra.4 with a matching annotation. [wsa: fix spi_gpio_request(), too] Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
| * | | | spi/fsl-espi: disable CONFIG_SPI_FSL_ESPI=m buildJiri Slaby2011-12-071-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When spi_fsl_espi is chosen to be built as a module, there is a build error because we test only CONFIG_SPI_FSL_ESPI in declaration of struct mpc8xxx_spi in drivers/spi/spi_fsl_lib.h. Also some called functions are not exported. So we forbid CONFIG_SPI_FSL_ESPI to be tristate here. The error looks like: drivers/spi/spi_fsl_espi.c: In function 'fsl_espi_bufs': drivers/spi/spi_fsl_espi.c:232: error: 'struct mpc8xxx_spi' has no member named 'len' ... Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Kumar Gala <galak@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
| * | | | spi/nuc900: Include linux/module.hAxel Lin2011-12-071-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Include linux/module.h to fix below build error: CC drivers/spi/spi-nuc900.o drivers/spi/spi-nuc900.c:484: error: 'THIS_MODULE' undeclared here (not in a function) drivers/spi/spi-nuc900.c:489: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-nuc900.c:489: warning: data definition has no type or storage class drivers/spi/spi-nuc900.c:489: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR' drivers/spi/spi-nuc900.c:489: warning: function declaration isn't a prototype drivers/spi/spi-nuc900.c:490: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-nuc900.c:490: warning: data definition has no type or storage class drivers/spi/spi-nuc900.c:490: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION' drivers/spi/spi-nuc900.c:490: warning: function declaration isn't a prototype drivers/spi/spi-nuc900.c:491: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-nuc900.c:491: warning: data definition has no type or storage class drivers/spi/spi-nuc900.c:491: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE' drivers/spi/spi-nuc900.c:491: warning: function declaration isn't a prototype drivers/spi/spi-nuc900.c:492: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-nuc900.c:492: warning: data definition has no type or storage class drivers/spi/spi-nuc900.c:492: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS' drivers/spi/spi-nuc900.c:492: warning: function declaration isn't a prototype make[2]: *** [drivers/spi/spi-nuc900.o] Error 1 make[1]: *** [drivers/spi] Error 2 make: *** [drivers] Error 2 Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
| * | | | spi/ath79: fix compile error due to missing includeGabor Juhos2011-12-071-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Whithout including 'linux/module.h' spi-ath79 driver fails to compile with the these errors: drivers/spi/spi-ath79.c:273:12: error: 'THIS_MODULE' undeclared here (not in a function) drivers/spi/spi-ath79.c:278:20: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-ath79.c:278:1: warning: data definition has no type or storage class drivers/spi/spi-ath79.c:278:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION' drivers/spi/spi-ath79.c:278:20: warning: function declaration isn't a prototype drivers/spi/spi-ath79.c:279:15: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-ath79.c:279:1: warning: data definition has no type or storage class drivers/spi/spi-ath79.c:279:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR' drivers/spi/spi-ath79.c:279:15: warning: function declaration isn't a prototype drivers/spi/spi-ath79.c:280:16: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-ath79.c:280:1: warning: data definition has no type or storage class drivers/spi/spi-ath79.c:280:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE' drivers/spi/spi-ath79.c:280:16: warning: function declaration isn't a prototype drivers/spi/spi-ath79.c:281:14: error: expected declaration specifiers or '...' before string constant drivers/spi/spi-ath79.c:281:1: warning: data definition has no type or storage class drivers/spi/spi-ath79.c:281:1: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS' drivers/spi/spi-ath79.c:281:14: warning: function declaration isn't a prototype Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
* | | | | Merge branch 'for-linus' of git://neil.brown.name/mdLinus Torvalds2011-12-093-7/+32
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-linus' of git://neil.brown.name/md: md: raid5 crash during degradation md/raid5: never wait for bad-block acks on failed device. md: ensure new badblocks are handled promptly. md: bad blocks shouldn't cause a Blocked status on a Faulty device. md: take a reference to mddev during sysfs access. md: refine interpretation of "hold_active == UNTIL_IOCTL". md/lock: ensure updates to page_attrs are properly locked.
| * | | | | md: raid5 crash during degradationAdam Kwolek2011-12-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NULL pointer access causes crash in raid5 module. Signed-off-by: Adam Kwolek <adam.kwolek@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
| * | | | | md/raid5: never wait for bad-block acks on failed device.NeilBrown2011-12-081-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Once a device is failed we really want to completely ignore it. It should go away soon anyway. In particular the presence of bad blocks on it should not cause us to block as we won't be trying to write there anyway. So as soon as we can check if a device is Faulty, do so and pretend that it is already gone if it is Faulty. Signed-off-by: NeilBrown <neilb@suse.de>
| * | | | | md: ensure new badblocks are handled promptly.NeilBrown2011-12-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we mark blocks as bad we need them to be acknowledged by the metadata handler promptly. For an in-kernel metadata handler that was already being done. But for an external metadata handler we need to alert it of the change by sending a notification through the sysfs file. This adds that notification. Signed-off-by: NeilBrown <neilb@suse.de>
| * | | | | md: bad blocks shouldn't cause a Blocked status on a Faulty device.NeilBrown2011-12-081-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Once a device is marked Faulty the badblocks - whether acknowledged or not - become irrelevant. So they shouldn't cause the device to be marked as Blocked. Without this patch, a process might write "-blocked" to clear the Blocked status, but while that will correctly fail the device, it won't remove the apparent 'blocked' status. Signed-off-by: NeilBrown <neilb@suse.de>
| * | | | | md: take a reference to mddev during sysfs access.NeilBrown2011-12-081-1/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we are accessing an mddev via sysfs we know that the mddev cannot disappear because it has an embedded kobj which is refcounted by sysfs. And we also take the mddev_lock. However this is not enough. The final mddev_put could have been called and the mddev_delayed_delete is waiting for sysfs to let go so it can destroy the kobj and mddev. In this state there are a lot of changes that should not be attempted. To to guard against this we: - initialise mddev->all_mddevs in on last put so the state can be easily detected. - in md_attr_show and md_attr_store, check ->all_mddevs under all_mddevs_lock and mddev_get the mddev if it still appears to be active. This means that if we get to sysfs as the mddev is being deleted we will get -EBUSY. rdev_attr_store and rdev_attr_show are similar but already have sufficient protection. They check that rdev->mddev still points to mddev after taking mddev_lock. As this is cleared before delayed removal which can only be requested under the mddev_lock, this ensure the rdev and mddev are still alive. Signed-off-by: NeilBrown <neilb@suse.de>
| * | | | | md: refine interpretation of "hold_active == UNTIL_IOCTL".NeilBrown2011-12-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We like md devices to disappear when they really are not needed. However it is not possible to tell from the current state whether it is needed or not. We can only tell from recent history of changes. In particular immediately after we create an md device it looks very similar to immediately after we have finished with it. So we always preserve a newly created md device until something significant happens. This state is stored in 'hold_active'. The normal case is to keep it until an ioctl happens, as that will normally either activate it, or explicitly de-activate it. If it doesn't then it was probably created by mistake and it is now time to get rid of it. We can also modify an array via sysfs (instead of via ioctl) and we currently treat any change via sysfs like an ioctl as a sign that if it now isn't more active, it should be destroyed. However this is not appropriate as changes made via sysfs are more gradual so we should look for a more definitive change. So this patch only clears 'hold_active' from UNTIL_IOCTL to clear when the array_state is changed via sysfs. Other changes via sysfs are ignored. Signed-off-by: NeilBrown <neilb@suse.de>
| * | | | | md/lock: ensure updates to page_attrs are properly locked.NeilBrown2011-11-231-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Page attributes are set using __set_bit rather than set_bit as it normally called under a spinlock so the extra atomicity is not needed. However there are two places where we might set or clear page attributes without holding the spinlock. So add the spinlock in those cases. This might be the cause of occasional reports that bits a aren't getting clear properly - theory is that BITMAP_PAGE_PENDING gets lost when BITMAP_PAGE_NEEDWRITE is set or cleared. This is an inconvenience, not a threat to data safety. Signed-off-by: NeilBrown <neilb@suse.de>
* | | | | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tileLinus Torvalds2011-12-0910-26/+40
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: arch/tile: use new generic {enable,disable}_percpu_irq() routines drivers/net/ethernet/tile: use skb_frag_page() API asm-generic/unistd.h: support new process_vm_{readv,write} syscalls arch/tile: fix double-free bug in homecache_free_pages() arch/tile: add a few #includes and an EXPORT to catch up with kernel changes.
| * | | | | | arch/tile: use new generic {enable,disable}_percpu_irq() routinesChris Metcalf2011-12-033-20/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We provided very similar routines internally, but now we can hook into the generic framework by supplying our routines as function pointers in the irq_chip structure instead. Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
| * | | | | | drivers/net/ethernet/tile: use skb_frag_page() APIChris Metcalf2011-12-031-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This replaces raw access to the "page" field of the skb_frag_t. Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Acked-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-18 18:26:26 +0100