summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* thermal/drivers/qcom/tsens-v0_1: Add mdm9607 correction offsetsStephan Gerhold2023-06-263-1/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the msm-3.18 vendor kernel from Qualcomm, mdm9607 needs "correction factors" to adjust for additional offsets observed after the factory calibration values in the fuses [1, 2]. The fixed offsets should be applied unless there is a special calibration mode value that indicates that no offsets are needed [3]. Note that the new calibration mode values are called differently in this patch compared to the vendor kernel: - TSENS_TWO_POINT_CALIB_N_WA -> ONE_PT_CALIB2_NO_OFFSET - TSENS_TWO_POINT_CALIB_N_OFFSET_WA -> TWO_PT_CALIB_NO_OFFSET This is because close inspection of the calibration function [3] reveals that TSENS_TWO_POINT_CALIB_N_WA is actually a "one point" calibration because the if statements skip all "point2" related code for it. [1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d9d2db1b82bf3f72f5de0803d55e6849eb5b671e [2]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d75aef53a760e8ff7bac54049d00c8b2ee1b193e [3]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/drivers/thermal/msm-tsens.c#L2987-3136 Fixes: a2149ab815fc ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607") Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-3-5eb632235ba7@kernkonzept.com
* thermal/drivers/qcom/tsens-v0_1: Fix mdm9607 slope valuesStephan Gerhold2023-06-261-1/+17
| | | | | | | | | | | | | | | According to the msm-3.18 vendor kernel from Qualcomm [1], mdm9607 uses a non-standard slope value of 3000 (instead of 3200) for all sensors. Fill it properly similar to the 8939 code added recently. [1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/arch/arm/boot/dts/qcom/mdm9607.dtsi#L875 Fixes: a2149ab815fc ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607") Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-2-5eb632235ba7@kernkonzept.com
* thermal/drivers/qcom/tsens: Drop unused legacy structsStephan Gerhold2023-06-262-58/+0
| | | | | | | | | | | | | | | | The old single-cell parsing code was removed for MSM8939, MDM9607 and MSM8976 but for some reason the structs defining the bit positions etc were kept around (unused). Drop them now. Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Fixes: 51d78b8b1beb ("thermal/drivers/tsens: Drop single-cell code for mdm9607") Fixes: dfadb4599ab0 ("thermal/drivers/tsens: Drop single-cell code for msm8939") Fixes: 3a908971f7cb ("thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956") Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-1-5eb632235ba7@kernkonzept.com
* dt-bindings: thermal: tsens: Add ipq9574 compatiblePraveenkumar I2023-06-261-0/+6
| | | | | | | | | | Qualcomm IPQ9574 has tsens v2.3.1 block, which is similar to IPQ8074 tsens. Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/ec9799504fe5a141e107bb78955d8d427f00553f.1686125196.git.quic_varada@quicinc.com
* dt-bindings: thermal: convert bcm2835-thermal bindings to YAMLStefan Wahren2023-06-262-41/+48
| | | | | | | | | Convert the DT binding document for bcm2835-thermal from .txt to YAML. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230604121223.9625-10-stefan.wahren@i2se.com
* thermal: Allow selecting the bang-bang governor as defaultThierry Reding2023-06-262-0/+10
| | | | | | | | | | | | | | | | | | For many setups the bang-bang governor is exactly what we want. Many ARM SoC-based devices use fans to cool down the entire SoC and that works well only with the bang-bang governor because it uses the hysteresis in order to let the fan run for a while to cool the SoC down below the trip point before switching it off again. The step-wise governor will behave strangely in these situations. It doesn't use the hysteresis, so it can lead to situations where the fan is turned on for only a very brief period and then is switched back off, only to get switched back on again very quickly because the SoC hasn't cooled down very much. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20230609124408.3788680-1-thierry.reding@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
* thermal/drivers/qcom/tsens-v0_1: Add support for MSM8226Matti Lehtimäki2023-06-263-2/+30
| | | | | | | | | | | The MSM8226 TSENS IP has 6 thermal sensors in a TSENS v0.1 block. The thermal sensors use non-standard slope values. Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230507201225.89694-4-matti.lehtimaki@gmail.com
* dt-bindings: thermal: tsens: Add compatible for MSM8226Matti Lehtimäki2023-06-261-0/+1
| | | | | | | | | | Qualcomm MSM8226 has tsens v0.1 block. Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230507201225.89694-3-matti.lehtimaki@gmail.com
* drivers/thermal/rcar_gen3_thermal: add reading fuses for Gen4Wolfram Sang2023-06-261-2/+42
| | | | | | | | | | | | The registers are differently named and at different offsets, but their functionality is the same as for Gen3. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230511192220.7523-4-wsa+renesas@sang-engineering.com
* drivers/thermal/rcar_gen3_thermal: refactor reading fuses into seprarate ↵Wolfram Sang2023-06-261-24/+36
| | | | | | | | | | | | | | function Gen4 will be very different, so refactor Gen3 access into separate call first. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230511192220.7523-3-wsa+renesas@sang-engineering.com
* drivers/thermal/rcar_gen3_thermal: introduce 'info' structureWolfram Sang2023-06-261-15/+26
| | | | | | | | | | | | More items to describe the TSCs are needed soon, so encapsulate the current 'ths_tj_1' item into a struct. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230511192220.7523-2-wsa+renesas@sang-engineering.com
* dt-bindings: thermal: tsens: Add compatible for SM6375Konrad Dybcio2023-06-261-0/+1
| | | | | | | | | | The Qualcomm SM6375 platform has two instances of the tsens v2.8.0 block, add a compatible for these instances. Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230516-topic-lost_tsens_bindings-v1-2-99715746ddb1@linaro.org
* dt-bindings: thermal: tsens: Add QCM2290Konrad Dybcio2023-06-261-0/+1
| | | | | | | | | Add the TSENS v2.x controller found on QCM2290. Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230516-topic-lost_tsens_bindings-v1-1-99715746ddb1@linaro.org
* thermal/intel/intel_soc_dts_iosf: Fix reporting wrong temperaturesHans de Goede2023-06-151-1/+1
| | | | | | | | | | | | | | | | | | | | Since commit 955fb8719efb ("thermal/intel/intel_soc_dts_iosf: Use Intel TCC library") intel_soc_dts_iosf is reporting the wrong temperature. The driver expects tj_max to be in milli-degrees-celcius but after the switch to the TCC library this is now in degrees celcius so instead of e.g. 90000 it is set to 90 causing a temperature 45 degrees below tj_max to be reported as -44910 milli-degrees instead of as 45000 milli-degrees. Fix this by adding back the lost factor of 1000. Fixes: 955fb8719efb ("thermal/intel/intel_soc_dts_iosf: Use Intel TCC library") Reported-by: Bernhard Krug <b.krug@elektronenpumpe.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.3+ <stable@vger.kernel.org> # 6.3+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Linux 6.4-rc6v6.4-rc6Linus Torvalds2023-06-111-1/+1
|
* Merge tag 'x86_urgent_for_v6.4_rc6' of ↵Linus Torvalds2023-06-111-9/+9
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fix from Borislav Petkov: - Set up the kernel CS earlier in the boot process in case EFI boots the kernel after bypassing the decompressor and the CS descriptor used ends up being the EFI one which is not mapped in the identity page table, leading to early SEV/SNP guest communication exceptions resulting in the guest crashing * tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/head/64: Switch to KERNEL_CS as soon as new GDT is installed
| * x86/head/64: Switch to KERNEL_CS as soon as new GDT is installedTom Lendacky2023-06-031-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The call to startup_64_setup_env() will install a new GDT but does not actually switch to using the KERNEL_CS entry until returning from the function call. Commit bcce82908333 ("x86/sev: Detect/setup SEV/SME features earlier in boot") moved the call to sme_enable() earlier in the boot process and in between the call to startup_64_setup_env() and the switch to KERNEL_CS. An SEV-ES or an SEV-SNP guest will trigger #VC exceptions during the call to sme_enable() and if the CS pushed on the stack as part of the exception and used by IRETQ is not mapped by the new GDT, then problems occur. Today, the current CS when entering startup_64 is the kernel CS value because it was set up by the decompressor code, so no issue is seen. However, a recent patchset that looked to avoid using the legacy decompressor during an EFI boot exposed this bug. At entry to startup_64, the CS value is that of EFI and is not mapped in the new kernel GDT. So when a #VC exception occurs, the CS value used by IRETQ is not valid and the guest boot crashes. Fix this issue by moving the block that switches to the KERNEL_CS value to be done immediately after returning from startup_64_setup_env(). Fixes: bcce82908333 ("x86/sev: Detect/setup SEV/SME features earlier in boot") Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Joerg Roedel <jroedel@suse.de> Link: https://lore.kernel.org/all/6ff1f28af2829cc9aea357ebee285825f90a431f.1684340801.git.thomas.lendacky%40amd.com
* | Merge tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbdLinus Torvalds2023-06-116-56/+62
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull smb server fixes from Steve French: "Five smb3 server fixes, all also for stable: - Fix four slab out of bounds warnings: improve checks for protocol id, and for small packet length, and for create context parsing, and for negotiate context parsing - Fix for incorrect dereferencing POSIX ACLs" * tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd: ksmbd: validate smb request protocol id ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR() ksmbd: fix out-of-bound read in parse_lease_state() ksmbd: fix out-of-bound read in deassemble_neg_contexts()
| * | ksmbd: validate smb request protocol idNamjae Jeon2023-06-022-3/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add the validation for smb request protocol id. If it is not one of the four ids(SMB1_PROTO_NUMBER, SMB2_PROTO_NUMBER, SMB2_TRANSFORM_PROTO_NUM, SMB2_COMPRESSION_TRANSFORM_ID), don't allow processing the request. And this will fix the following KASAN warning also. [ 13.905265] BUG: KASAN: slab-out-of-bounds in init_smb2_rsp_hdr+0x1b9/0x1f0 [ 13.905900] Read of size 16 at addr ffff888005fd2f34 by task kworker/0:2/44 ... [ 13.908553] Call Trace: [ 13.908793] <TASK> [ 13.908995] dump_stack_lvl+0x33/0x50 [ 13.909369] print_report+0xcc/0x620 [ 13.910870] kasan_report+0xae/0xe0 [ 13.911519] kasan_check_range+0x35/0x1b0 [ 13.911796] init_smb2_rsp_hdr+0x1b9/0x1f0 [ 13.912492] handle_ksmbd_work+0xe5/0x820 Cc: stable@vger.kernel.org Reported-by: Chih-Yen Chang <cc85nod@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
| * | ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loopNamjae Jeon2023-06-021-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The length field of netbios header must be greater than the SMB header sizes(smb1 or smb2 header), otherwise the packet is an invalid SMB packet. If `pdu_size` is 0, ksmbd allocates a 4 bytes chunk to `conn->request_buf`. In the function `get_smb2_cmd_val` ksmbd will read cmd from `rcv_hdr->Command`, which is `conn->request_buf + 12`, causing the KASAN detector to print the following error message: [ 7.205018] BUG: KASAN: slab-out-of-bounds in get_smb2_cmd_val+0x45/0x60 [ 7.205423] Read of size 2 at addr ffff8880062d8b50 by task ksmbd:42632/248 ... [ 7.207125] <TASK> [ 7.209191] get_smb2_cmd_val+0x45/0x60 [ 7.209426] ksmbd_conn_enqueue_request+0x3a/0x100 [ 7.209712] ksmbd_server_process_request+0x72/0x160 [ 7.210295] ksmbd_conn_handler_loop+0x30c/0x550 [ 7.212280] kthread+0x160/0x190 [ 7.212762] ret_from_fork+0x1f/0x30 [ 7.212981] </TASK> Cc: stable@vger.kernel.org Reported-by: Chih-Yen Chang <cc85nod@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
| * | ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()Namjae Jeon2023-06-022-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dan reported the following error message: fs/smb/server/smbacl.c:1296 smb_check_perm_dacl() error: 'posix_acls' dereferencing possible ERR_PTR() fs/smb/server/vfs.c:1323 ksmbd_vfs_make_xattr_posix_acl() error: 'posix_acls' dereferencing possible ERR_PTR() fs/smb/server/vfs.c:1830 ksmbd_vfs_inherit_posix_acl() error: 'acls' dereferencing possible ERR_PTR() __get_acl() returns a mix of error pointers and NULL. This change it with IS_ERR_OR_NULL(). Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Cc: stable@vger.kernel.org Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
| * | ksmbd: fix out-of-bound read in parse_lease_state()Namjae Jeon2023-06-021-42/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This bug is in parse_lease_state, and it is caused by the missing check of `struct create_context`. When the ksmbd traverses the create_contexts, it doesn't check if the field of `NameOffset` and `Next` is valid, The KASAN message is following: [ 6.664323] BUG: KASAN: slab-out-of-bounds in parse_lease_state+0x7d/0x280 [ 6.664738] Read of size 2 at addr ffff888005c08988 by task kworker/0:3/103 ... [ 6.666644] Call Trace: [ 6.666796] <TASK> [ 6.666933] dump_stack_lvl+0x33/0x50 [ 6.667167] print_report+0xcc/0x620 [ 6.667903] kasan_report+0xae/0xe0 [ 6.668374] kasan_check_range+0x35/0x1b0 [ 6.668621] parse_lease_state+0x7d/0x280 [ 6.668868] smb2_open+0xbe8/0x4420 [ 6.675137] handle_ksmbd_work+0x282/0x820 Use smb2_find_context_vals() to find smb2 create request lease context. smb2_find_context_vals validate create context fields. Cc: stable@vger.kernel.org Reported-by: Chih-Yen Chang <cc85nod@gmail.com> Tested-by: Chih-Yen Chang <cc85nod@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
| * | ksmbd: fix out-of-bound read in deassemble_neg_contexts()Namjae Jeon2023-06-021-7/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The check in the beginning is `clen + sizeof(struct smb2_neg_context) <= len_of_ctxts`, but in the end of loop, `len_of_ctxts` will subtract `((clen + 7) & ~0x7) + sizeof(struct smb2_neg_context)`, which causes integer underflow when clen does the 8 alignment. We should use `(clen + 7) & ~0x7` in the check to avoid underflow from happening. Then there are some variables that need to be declared unsigned instead of signed. [ 11.671070] BUG: KASAN: slab-out-of-bounds in smb2_handle_negotiate+0x799/0x1610 [ 11.671533] Read of size 2 at addr ffff888005e86cf2 by task kworker/0:0/7 ... [ 11.673383] Call Trace: [ 11.673541] <TASK> [ 11.673679] dump_stack_lvl+0x33/0x50 [ 11.673913] print_report+0xcc/0x620 [ 11.674671] kasan_report+0xae/0xe0 [ 11.675171] kasan_check_range+0x35/0x1b0 [ 11.675412] smb2_handle_negotiate+0x799/0x1610 [ 11.676217] ksmbd_smb_negotiate_common+0x526/0x770 [ 11.676795] handle_ksmbd_work+0x274/0x810 ... Cc: stable@vger.kernel.org Signed-off-by: Chih-Yen Chang <cc85nod@gmail.com> Tested-by: Chih-Yen Chang <cc85nod@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
* | | Merge tag 'i2c-for-6.4-rc6' of ↵Linus Torvalds2023-06-108-7/+37
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "Biggest news is that Andi Shyti steps in for maintaining the controller drivers. Thank you very much! Other than that, one new driver maintainer and the rest is usual driver bugfixes. at24 has a Kconfig dependecy fix" * tag 'i2c-for-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver eeprom: at24: also select REGMAP i2c: sprd: Delete i2c adapter in .remove's error path i2c: mv64xxx: Fix reading invalid status value in atomic mode i2c: designware: fix idx_write_cnt in read loop i2c: mchp-pci1xxxx: Avoid cast to incompatible function type i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate" MAINTAINERS: Add myself as I2C host drivers maintainer
| * \ \ Merge tag 'at24-fixes-for-v6.4-rc6' of ↵Wolfram Sang2023-06-091-0/+1
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current at24 fixes for v6.4-rc6 - fix a Kconfig issue (we need to select REGMAP, not only REGMAP_I2C)
| | * | | eeprom: at24: also select REGMAPRandy Dunlap2023-06-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Selecting only REGMAP_I2C can leave REGMAP unset, causing build errors, so also select REGMAP to prevent the build errors. ../drivers/misc/eeprom/at24.c:540:42: warning: 'struct regmap_config' declared inside parameter list will not be visible outside of this definition or declaration 540 | struct regmap_config *regmap_config) ../drivers/misc/eeprom/at24.c: In function 'at24_make_dummy_client': ../drivers/misc/eeprom/at24.c:552:18: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration] 552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config); ../drivers/misc/eeprom/at24.c:552:16: warning: assignment to 'struct regmap *' from 'int' makes pointer from integer without a cast [-Wint-conversion] 552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config); ../drivers/misc/eeprom/at24.c: In function 'at24_probe': ../drivers/misc/eeprom/at24.c:586:16: error: variable 'regmap_config' has initializer but incomplete type 586 | struct regmap_config regmap_config = { }; ../drivers/misc/eeprom/at24.c:586:30: error: storage size of 'regmap_config' isn't known 586 | struct regmap_config regmap_config = { }; ../drivers/misc/eeprom/at24.c:586:30: warning: unused variable 'regmap_config' [-Wunused-variable] Fixes: 5c015258478e ("eeprom: at24: add basic regmap_i2c support") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
| * | | | MAINTAINERS: Add entries for Renesas RZ/V2M I2C driverBiju Das2023-06-081-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the MAINTAINERS entries for the Renesas RZ/V2M I2C driver. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Acked-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
| * | | | i2c: sprd: Delete i2c adapter in .remove's error pathUwe Kleine-König2023-06-071-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If pm runtime resume fails the .remove callback used to exit early. This resulted in an error message by the driver core but the device gets removed anyhow. This lets the registered i2c adapter stay around with an unbound parent device. So only skip clk disabling if resume failed, but do delete the adapter. Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
| * | | | i2c: mv64xxx: Fix reading invalid status value in atomic modeMarek Behún2023-06-051-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There seems to be a bug within the mv64xxx I2C controller, wherein the status register may not necessarily contain valid value immediately after the IFLG flag is set in the control register. My theory is that the controller: - first sets the IFLG in control register - then updates the status register - then raises an interrupt This may sometime cause weird bugs when in atomic mode, since in this mode we do not wait for an interrupt, but instead we poll the control register for IFLG and read status register immediately after. I encountered -ENXIO from mv64xxx_i2c_fsm() due to this issue when using this driver in atomic mode. Note that I've only seen this issue on Armada 385, I don't know whether other SOCs with this controller are also affected. Also note that this fix has been in U-Boot for over 4 years [1] without anybody complaining, so it should not cause regressions. [1] https://source.denx.de/u-boot/u-boot/-/commit/d50e29662f78 Fixes: 544a8d75f3d6 ("i2c: mv64xxx: Add atomic_xfer method to driver") Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
| * | | | i2c: designware: fix idx_write_cnt in read loopDavid Zheng2023-06-052-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With IC_INTR_RX_FULL slave interrupt handler reads data in a loop until RX FIFO is empty. When testing with the slave-eeprom, each transaction has 2 bytes for address/index and 1 byte for value, the address byte can be written as data byte due to dropping STOP condition. In the test below, the master continuously writes to the slave, first 2 bytes are index, 3rd byte is value and follow by a STOP condition. i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D1-D1] i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D2-D2] i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D3-D3] Upon receiving STOP condition slave eeprom would reset `idx_write_cnt` so next 2 bytes can be treated as buffer index for upcoming transaction. Supposedly the slave eeprom buffer would be written as EEPROM[0x00D1] = 0xD1 EEPROM[0x00D2] = 0xD2 EEPROM[0x00D3] = 0xD3 When CPU load is high the slave irq handler may not read fast enough, the interrupt status can be seen as 0x204 with both DW_IC_INTR_STOP_DET (0x200) and DW_IC_INTR_RX_FULL (0x4) bits. The slave device may see the transactions below. 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1794 : INTR_STAT=0x204 0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x1790 : INTR_STAT=0x200 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4 After `D1` is received, read loop continues to read `00` which is the first bype of next index. Since STOP condition is ignored by the loop, eeprom buffer index increased to `D2` and `00` is written as value. So the slave eeprom buffer becomes EEPROM[0x00D1] = 0xD1 EEPROM[0x00D2] = 0x00 EEPROM[0x00D3] = 0xD3 The fix is to use `FIRST_DATA_BYTE` (bit 11) in `IC_DATA_CMD` to split the transactions. The first index byte in this case would have bit 11 set. Check this indication to inject I2C_SLAVE_WRITE_REQUESTED event which will reset `idx_write_cnt` in slave eeprom. Signed-off-by: David Zheng <david.zheng@intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
| * | | | i2c: mchp-pci1xxxx: Avoid cast to incompatible function typeSimon Horman2023-06-051-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rather than casting pci1xxxx_i2c_shutdown to an incompatible function type, update the type to match that expected by __devm_add_action. Reported by clang-16 with W-1: .../i2c-mchp-pci1xxxx.c:1159:29: error: cast from 'void (*)(struct pci1xxxx_i2c *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict] ret = devm_add_action(dev, (void (*)(void *))pci1xxxx_i2c_shutdown, i2c); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ./include/linux/device.h:251:29: note: expanded from macro 'devm_add_action' __devm_add_action(release, action, data, #action) ^~~~~~ No functional change intended. Compile tested only. Signed-off-by: Simon Horman <horms@kernel.org> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Reviewed-by: Tharun Kumar P<tharunkumar.pasumarthi@microchip.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
| * | | | i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate"Christian Heusel2023-06-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is a spelling mistake in a comment. Fix it. Signed-off-by: Christian Heusel <christian@heusel.eu> Signed-off-by: Wolfram Sang <wsa@kernel.org>
| * | | | MAINTAINERS: Add myself as I2C host drivers maintainerAndi Shyti2023-06-051-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I will help Wolfram out with the i2c controllers patches. Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
* | | | | Merge tag 'soundwire-6.4-fixes' of ↵Linus Torvalds2023-06-103-5/+23
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire Pull soundwire fixes from Vinod Koul: "Core fix for missing flag clear, error patch handling in qcom driver and BIOS quirk for HP Spectre x360: - HP Spectre x360 soundwire DMI quirk - Error path handling for qcom driver - Core fix for missing clear of alloc_slave_rt" * tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: soundwire: stream: Add missing clear of alloc_slave_rt soundwire: qcom: add proper error paths in qcom_swrm_startup() soundwire: dmi-quirks: add new mapping for HP Spectre x360
| * | | | | soundwire: stream: Add missing clear of alloc_slave_rtCharles Keepax2023-06-081-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current path that skips allocating the slave runtime does not clear the alloc_slave_rt flag, this is clearly incorrect. Add the missing clear, so the runtime won't be erroneously cleaned up. Fixes: f3016b891c8c ("soundwire: stream: sdw_stream_add_ functions can be called multiple times") Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20230602101140.2040141-1-ckeepax@opensource.cirrus.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
| * | | | | soundwire: qcom: add proper error paths in qcom_swrm_startup()Krzysztof Kozlowski2023-05-271-4/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reverse actions in qcom_swrm_startup() error paths to avoid leaking stream memory and keeping runtime PM unbalanced. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20230517163736.997553-1-krzysztof.kozlowski@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
| * | | | | soundwire: dmi-quirks: add new mapping for HP Spectre x360Pierre-Louis Bossart2023-05-271-0/+7
| | |/ / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A BIOS/DMI update seems to have broken some devices, let's add a new mapping. Link: https://github.com/thesofproject/linux/issues/4323 Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20230515074859.3097-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
* | | | | Merge tag 'arm-fixes-6.4-2' of ↵Linus Torvalds2023-06-1082-226/+479
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "Most of the changes this time are for the Qualcomm Snapdragon platforms. There are bug fixes for error handling in Qualcomm icc-bwmon, rpmh-rsc, ramp_controller and rmtfs driver as well as the AMD tee firmware driver and a missing initialization in the Arm ff-a firmware driver. The Qualcomm RPMh and EDAC drivers need some rework to work correctly on all supported chips. The DT fixes include: - i.MX8 fixes for gpio, pinmux and clock settings - ADS touchscreen gpio polarity settings in several machines - Address dtb warnings for caches, panel and input-enable properties on Qualcomm platforms - Incorrect data on qualcomm platforms fir SA8155P power domains, SM8550 LLCC, SC7180-lite SDRAM frequencies and SM8550 soundwire - Remoteproc firmware paths are corrected for Sony Xperia 10 IV" * tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits) firmware: arm_ffa: Set handle field to zero in memory descriptor ARM: dts: Fix erroneous ADS touchscreen polarities arm64: dts: imx8mn-beacon: Fix SPI CS pinmux arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals EDAC/qcom: Get rid of hardcoded register offsets EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup() arm64: dts: qcom: sm8550: Use the correct LLCC register scheme dt-bindings: cache: qcom,llcc: Fix SM8550 description arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards arm64: dts: qcom: sm8550: use uint16 for Soundwire interval soc: qcom: rpmhpd: Add SA8155P power domains arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains dt-bindings: power: qcom,rpmpd: Add SA8155P soc: qcom: Rename ice to qcom_ice to avoid module name conflict soc: qcom: rmtfs: Fix error code in probe() soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe() ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc ARM: at91: pm: fix imbalanced reference counter for ethernet devices arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths ...
| * \ \ \ \ Merge tag 'imx-fixes-6.4-2' of ↵Arnd Bergmann2023-06-093-4/+12
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 6.4, round 2: - Fix SPI CS pinmux for the final production version of imx8mn-beacon board. - Fix GPIOs for USDHC2 CD and WP signals on imx8qm-mek board. - Assign default clock rate for i.MX8 LPUARTs to fix UART failure. * tag 'imx-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: arm64: dts: imx8mn-beacon: Fix SPI CS pinmux arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals Link: https://lore.kernel.org/r/20230607141312.GU4199@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| | * | | | | arm64: dts: imx8mn-beacon: Fix SPI CS pinmuxAdam Ford2023-06-041-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The final production baseboard had a different chip select than earlier prototype boards. When the newer board was released, the SPI stopped working because the wrong pin was used in the device tree and conflicted with the UART RTS. Fix the pinmux for production boards. Fixes: 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
| | * | | | | arm64: dts: imx8-ss-dma: assign default clock rate for lpuartsShenwei Wang2023-05-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the assigned-clocks and assigned-clock-rates properties for the LPUARTx nodes. Without these properties, the default clock rate used would be 0, which can cause the UART ports to fail when open. Fixes: 35f4e9d7530f ("arm64: dts: imx8: split adma ss into dma and audio ss") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
| | * | | | | arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signalsShenwei Wang2023-05-271-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The USDHC2 CD and WP sginal should be on LSIO_GPIO5. Fixes: 307fd14d4b14 ("arm64: dts: imx: add imx8qm mek support") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
| * | | | | | Merge tag 'amdtee-fix-for-v6.5' of ↵Arnd Bergmann2023-06-072-17/+23
| |\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes AMDTEE add return origin to load TA command * tag 'amdtee-fix-for-v6.5' of https://git.linaro.org/people/jens.wiklander/linux-tee: tee: amdtee: Add return_origin to 'struct tee_cmd_load_ta' Link: https://lore.kernel.org/r/20230606075843.GA2792442@rayden Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| | * | | | | | tee: amdtee: Add return_origin to 'struct tee_cmd_load_ta'Rijo Thomas2023-05-152-17/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After TEE has completed processing of TEE_CMD_ID_LOAD_TA, set proper value in 'return_origin' argument passed by open_session() call. To do so, add 'return_origin' field to the structure tee_cmd_load_ta. The Trusted OS shall update return_origin as part of TEE processing. This change to 'struct tee_cmd_load_ta' interface requires a similar update in AMD-TEE Trusted OS's TEE_CMD_ID_LOAD_TA interface. This patch has been verified on Phoenix Birman setup. On older APUs, return_origin value will be 0. Cc: stable@vger.kernel.org Fixes: 757cc3e9ff1d ("tee: add AMD-TEE driver") Tested-by: Sourabh Das <sourabh.das@amd.com> Signed-off-by: Rijo Thomas <Rijo-john.Thomas@amd.com> Acked-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
| * | | | | | | Merge tag 'ffa-fix-6.4-2' of ↵Arnd Bergmann2023-06-061-0/+1
| |\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes Arm FF-A fix for v6.4 A single fix addressing another MBZ field being non-zero and non-compliant resulting in the rejection of certain memory interface transmissions by the receivers(secure partitions). The issue was addressed before but missed to address this one field which is part of this change. * tag 'ffa-fix-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: firmware: arm_ffa: Set handle field to zero in memory descriptor Link: https://lore.kernel.org/r/20230606125720.2816923-1-sudeep.holla@arm.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| | * | | | | | | firmware: arm_ffa: Set handle field to zero in memory descriptorBalint Dobszay2023-06-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As described in the commit 111a833dc5cb ("firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors") some fields in the memory descriptor have to be zeroed explicitly. The handle field is one of these, but it was left out from that change, fix this now. Fixes: 111a833dc5cb ("firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors") Reported-by: Imre Kis <imre.kis@arm.com> Signed-off-by: Balint Dobszay <balint.dobszay@arm.com> Link: https://lore.kernel.org/r/20230601140749.93812-1-balint.dobszay@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
| * | | | | | | | ARM: dts: Fix erroneous ADS touchscreen polaritiesLinus Walleij2023-06-0511-11/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several device tree files get the polarity of the pendown-gpios wrong: this signal is active low. Fix up all incorrect flags, so that operating systems can rely on the flag being correctly set. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20230510105156.1134320-1-linus.walleij@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| * | | | | | | | Merge tag 'at91-fixes-6.4' of ↵Arnd Bergmann2023-06-052-12/+10
| |\ \ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes AT91 fixes for 6.4 It contains: - fix imbalanced reference counter for ethernet devices; without it system hangs after consecutive suspend/resume cycles; - fix debounce delay property for shutdown controller; the initial DT property is not what the driver expects. * tag 'at91-fixes-6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc ARM: at91: pm: fix imbalanced reference counter for ethernet devices Link: https://lore.kernel.org/r/20230530105930.11621-1-claudiu.beznea@microchip.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| | * | | | | | | | ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwcClaudiu Beznea2023-05-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is no atmel,shdwc-debouncer property for SHDWC. The right DT property is debounce-delay-us. Use it. Fixes: 16b161bcf5d4 ("ARM: dts: at91: sama7g5: add shdwc node") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20230523052750.184223-1-claudiu.beznea@microchip.com
| | * | | | | | | | ARM: at91: pm: fix imbalanced reference counter for ethernet devicesClaudiu Beznea2023-05-241-11/+9
| | | |_|_|/ / / / | | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The of_find_device_by_node() function is returning a struct platform_device object with the embedded struct device member's reference counter incremented. This needs to be dropped when done with the platform device returned by of_find_device_by_node(). at91_pm_eth_quirk_is_valid() calls of_find_device_by_node() on suspend and resume path. On suspend it calls of_find_device_by_node() and on resume and failure paths it drops the counter of struct platform_device::dev. In case ethernet device may not wakeup there is a put_device() on at91_pm_eth_quirk_is_valid() which is wrong as it colides with put_device() on resume path leading to the reference counter of struct device embedded in struct platform_device to be messed, stack trace to be displayed (after 5 consecutive suspend/resume cycles) and execution to hang. Along with this the error path of at91_pm_config_quirks() had been also adapted to decrement propertly the reference counter of struct device embedded in struct platform_device. Fixes: b7fc72c63399 ("ARM: at91: pm: add quirks for pm") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20230518062511.2988500-1-claudiu.beznea@microchip.com
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-26 10:56:21 +0100