summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ACPI: bus: Drop ACPI_BUS_COMPONENT which is not used any moreRafael J. Wysocki2021-02-043-9/+6
| | | | | | | After dropping all of the code using ACPI_BUS_COMPONENT drop it too and modify the example in the documentation using it. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* ACPI: utils: Clean up printing messagesRafael J. Wysocki2021-02-041-38/+18
| | | | | | | | | | | | | Replace all of the ACPI_DEBUG_PRINT() instances in utils.c with pr_debug() and acpi_handle_debug(), drop the _COMPONENT and ACPI_MODULE_NAME() definitions that are not used any more and replace direct printk() invocations with pr_debug() calls (the log level in there is way excessive). Also add a special pr_fmt() definition, but this only affects the pr_debug() messages mentioned above. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* ACPI: scan: Clean up printing messagesRafael J. Wysocki2021-02-041-17/+12
| | | | | | | | | | | | | | Replace all of the ACPI_DEBUG_PRINT() and ACPI_EXCEPTION() instances in scan.c with acpi_handle_debug() and acpi_handle_info(), respectively, and drop the _COMPONENT and ACPI_MODULE_NAME() definitions that are not used any more. While at it, drop the redundant "Memory allocation error" message from acpi_add_single_object() and clean up the list of local variables in that function. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reported-by: kernel test robot <lkp@intel.com>
* ACPI: bus: Clean up printing messagesRafael J. Wysocki2021-02-041-34/+26
| | | | | | | | | | | Replace all of the ACPI_DEBUG_PRINT() and ACPI_EXCEPTION() instances in bus.c with pr_debug() and pr_info(), respectively, drop the _COMPONENT and ACPI_MODULE_NAME() definitions that are not used any more and replace direct printk() invocations with the matching pr_*() calls (with a couple of exceptions where the log level is decreased). Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* ACPI: PM: Clean up printing messagesRafael J. Wysocki2021-02-044-15/+8
| | | | | | | | | Replace the remaining ACPI_DEBUG_PRINT() instances in device_pm.c with dev_dbg() invocations, drop the _COMPONENT and ACPI_MODULE_NAME() definitions that are not used any more, and drop the no longer needed ACPI_POWER_COMPONENT definition from the headers and documentation. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* ACPI: power: Clean up printing messagesRafael J. Wysocki2021-02-041-29/+15
| | | | | | | | | | | Replace all of the ACPI_DEBUG_PRINT() instances in power.c with acpi_handle_debug() or pr_debug(), depending on the context, drop the _COMPONENT and ACPI_MODULE_NAME() definitions that are not used any more, and replace the direct invocations of printk() in there with acpi_handle_info() or pr_info(), depending on the context. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Merge branch 'acpi-scan' into acpi-messagesRafael J. Wysocki2021-02-041-50/+49
|\
| * ACPI: scan: Rearrange code related to acpi_get_device_data()Rafael J. Wysocki2021-01-251-18/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two callers of acpi_get_device_data(), acpi_bus_get_device() and acpi_bus_get_acpi_device(), but only one of them takes the int return value into account. Moreover, the latter knows that it passes a valid return pointer to acpi_get_device_data() and it properly clears that pointer upfront, so it doesn't need acpi_get_device_data() to do that. For this reason, rearrange acpi_get_device_data() to return a strct acpi_device pointer instead of an int and adapt its callers to that. While at it, rename acpi_get_device_data() to handle_to_device(), because the old name does not really reflect the functionality provided by that function. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
| * ACPI: scan: Adjust white space in acpi_device_add()Rafael J. Wysocki2021-01-251-2/+7
| | | | | | | | | | | | | | | | | | | | Add empty lines in some places in acpi_device_add() to help readability and drop leading spaces before the labels in there. No functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
| * ACPI: scan: Rearrange memory allocation in acpi_device_add()Rafael J. Wysocki2021-01-251-31/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The upfront allocation of new_bus_id is done to avoid allocating memory under acpi_device_lock, but it doesn't really help, because (1) it leads to many unnecessary memory allocations for _ADR devices, (2) kstrdup_const() is run under that lock anyway and (3) it complicates the code. Rearrange acpi_device_add() to allocate memory for a new struct acpi_device_bus_id instance only when necessary, eliminate a redundant local variable from it and reduce the number of labels in there. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
* | Linux 5.11-rc6v5.11-rc6Linus Torvalds2021-01-311-1/+1
| |
* | Merge tag 'efi-urgent-for-v5.11' of ↵Linus Torvalds2021-01-311-4/+9
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull EFI fix from Borislav Petkov: "A single fix from Lukas: handle boolean device properties imported from Apple firmware correctly" * tag 'efi-urgent-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: efi/apple-properties: Reinstate support for boolean properties
| * | efi/apple-properties: Reinstate support for boolean propertiesLukas Wunner2020-12-311-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 4466bf82821b ("efi/apple-properties: use PROPERTY_ENTRY_U8_ARRAY_LEN"), my MacBook Pro issues a -ENODATA error when trying to assign EFI properties to the discrete GPU: pci 0000:01:00.0: assigning 56 device properties pci 0000:01:00.0: error -61 assigning properties That's because some of the properties have no value. They're booleans whose presence can be checked by drivers, e.g. "use-backlight-blanking". Commit 6e98503dba64 ("efi/apple-properties: Remove redundant attribute initialization from unmarshal_key_value_pairs()") employed a trick to store such booleans as u8 arrays (which is the data type used for all other EFI properties on Macs): It cleared the property_entry's "is_array" flag, thereby denoting that the value is stored inline in the property_entry. Commit 4466bf82821b erroneously removed that trick. It was probably a little fragile to begin with. Reinstate support for boolean properties by explicitly invoking the PROPERTY_ENTRY_BOOL() initializer for properties with zero-length value. Fixes: 4466bf82821b ("efi/apple-properties: use PROPERTY_ENTRY_U8_ARRAY_LEN") Cc: <stable@vger.kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/be958bda75331a011d53c696d1deec8dccd06fd2.1609388549.git.lukas@wunner.de Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
* | | Merge tag 'x86_entry_for_v5.11_rc6' of ↵Linus Torvalds2021-01-313-10/+15
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fix from Borislav Petkov: "A single fix for objtool to generate proper unwind info for newer toolchains which do not generate section symbols anymore. And a cleanup ontop. This was originally going to go during the next merge window but people can already trigger a build error with binutils-2.36 which doesn't emit section symbols - something which objtool relies on - so let's expedite it" * tag 'x86_entry_for_v5.11_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/entry: Remove put_ret_addr_in_rdi THUNK macro argument x86/entry: Emit a symbol for register restoring thunk
| * | | x86/entry: Remove put_ret_addr_in_rdi THUNK macro argumentBorislav Petkov2021-01-191-6/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | That logic is unused since 320100a5ffe5 ("x86/entry: Remove the TRACE_IRQS cruft") Remove it. Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/YAAszZJ2GcIYZmB5@hirez.programming.kicks-ass.net
| * | | x86/entry: Emit a symbol for register restoring thunkNick Desaulniers2021-01-143-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Arnd found a randconfig that produces the warning: arch/x86/entry/thunk_64.o: warning: objtool: missing symbol for insn at offset 0x3e when building with LLVM_IAS=1 (Clang's integrated assembler). Josh notes: With the LLVM assembler not generating section symbols, objtool has no way to reference this code when it generates ORC unwinder entries, because this code is outside of any ELF function. The limitation now being imposed by objtool is that all code must be contained in an ELF symbol. And .L symbols don't create such symbols. So basically, you can use an .L symbol *inside* a function or a code segment, you just can't use the .L symbol to contain the code using a SYM_*_START/END annotation pair. Fangrui notes that this optimization is helpful for reducing image size when compiling with -ffunction-sections and -fdata-sections. I have observed on the order of tens of thousands of symbols for the kernel images built with those flags. A patch has been authored against GNU binutils to match this behavior of not generating unused section symbols ([1]), so this will also become a problem for users of GNU binutils once they upgrade to 2.36. Omit the .L prefix on a label so that the assembler will emit an entry into the symbol table for the label, with STB_LOCAL binding. This enables objtool to generate proper unwind info here with LLVM_IAS=1 or GNU binutils 2.36+. [ bp: Massage commit message. ] Reported-by: Arnd Bergmann <arnd@arndb.de> Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com> Suggested-by: Borislav Petkov <bp@alien8.de> Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Link: https://lkml.kernel.org/r/20210112194625.4181814-1-ndesaulniers@google.com Link: https://github.com/ClangBuiltLinux/linux/issues/1209 Link: https://reviews.llvm.org/D93783 Link: https://sourceware.org/binutils/docs/as/Symbol-Names.html Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=d1bcae833b32f1408485ce69f844dcd7ded093a8 [1]
* | | | Merge tag 'timers-urgent-2021-01-31' of ↵Linus Torvalds2021-01-312-0/+15
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer fix from Thomas Gleixner: "A fix for handling advertised, but non-existent 146818 RTCs correctly. With the recent UIP handling changes the time readout of non-existent RTCs hangs forever as the read returns always 0xFF which means the UIP bit is set. Sanity check the RTC before registering by checking the RTC_VALID register for correctness" * tag 'timers-urgent-2021-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: rtc: mc146818: Detect and handle broken RTCs
| * | | | rtc: mc146818: Detect and handle broken RTCsThomas Gleixner2021-01-272-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The recent fix for handling the UIP bit unearthed another issue in the RTC code. If the RTC is advertised but the readout is straight 0xFF because it's not available, the old code just proceeded with crappy values, but the new code hangs because it waits for the UIP bit to become low. Add a sanity check in the RTC CMOS probe function which reads the RTC_VALID register (Register D) which should have bit 0-6 cleared. If that's not the case then fail to register the CMOS. Add the same check to mc146818_get_time(), warn once when the condition is true and invalidate the rtc_time data. Reported-by: Mickaël Salaün <mic@digikod.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Mickaël Salaün <mic@linux.microsoft.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/87tur3fx7w.fsf@nanos.tec.linutronix.de
* | | | | Merge tag 'core-urgent-2021-01-31' of ↵Linus Torvalds2021-01-311-1/+1
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull single stepping fix from Thomas Gleixner: "A single fix for the single step reporting regression caused by getting the condition wrong when moving SYSCALL_EMU away from TIF flags" [ There's apparently another problem too, fix pending ] * tag 'core-urgent-2021-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: entry: Unbreak single step reporting behaviour
| * | | | | entry: Unbreak single step reporting behaviourYuxuan Shui2021-01-281-1/+1
| |/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The move of TIF_SYSCALL_EMU to SYSCALL_WORK_SYSCALL_EMU broke single step reporting. The original code reported the single step when TIF_SINGLESTEP was set and TIF_SYSCALL_EMU was not set. The SYSCALL_WORK conversion got the logic wrong and now the reporting only happens when both bits are set. Restore the original behaviour. [ tglx: Massaged changelog and dropped the pointless double negation ] Fixes: 64eb35f701f0 ("ptrace: Migrate TIF_SYSCALL_EMU to use SYSCALL_WORK flag") Signed-off-by: Yuxuan Shui <yshuiv7@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.com> Link: https://lore.kernel.org/r/877do3gaq9.fsf@m5Zedd9JOGzJrf0
* | | | | Merge tag 'powerpc-5.11-6' of ↵Linus Torvalds2021-01-311-12/+16
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fix from Michael Ellerman: "One fix for a bug in our soft interrupt masking, which could lead to interrupt replaying recursing, causing spurious interrupts. Thanks to Nicholas Piggin" * tag 'powerpc-5.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/64s: prevent recursive replay_soft_interrupts causing superfluous interrupt
| * | | | | powerpc/64s: prevent recursive replay_soft_interrupts causing superfluous ↵Nicholas Piggin2021-01-241-12/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | interrupt When an asynchronous interrupt calls irq_exit, it checks for softirqs that may have been created, and runs them. Running softirqs enables local irqs, which can replay pending interrupts causing recursion in replay_soft_interrupts. This abridged trace shows how this can occur: ! NIP replay_soft_interrupts LR interrupt_exit_kernel_prepare Call Trace: interrupt_exit_kernel_prepare (unreliable) interrupt_return --- interrupt: ea0 at __rb_reserve_next NIP __rb_reserve_next LR __rb_reserve_next Call Trace: ring_buffer_lock_reserve trace_function function_trace_call ftrace_call __do_softirq irq_exit timer_interrupt ! replay_soft_interrupts interrupt_exit_kernel_prepare interrupt_return --- interrupt: ea0 at arch_local_irq_restore This can not be prevented easily, because softirqs must not block hard irqs, so it has to be dealt with. The recursion is bounded by design in the softirq code because softirq replay disables softirqs and loops around again to check for new softirqs created while it ran, so that's not a problem. However it does mess up interrupt replay state, causing superfluous interrupts when the second replay_soft_interrupts clears a pending interrupt, leaving it still set in the first call in the 'happened' local variable. Fix this by not caching a copy of irqs_happened across interrupt handler calls. Fixes: 3282a3da25bd ("powerpc/64: Implement soft interrupt replay in C") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210123061244.2076145-1-npiggin@gmail.com
* | | | | | Merge branch 'i2c/for-current' of ↵Linus Torvalds2021-01-311-3/+16
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fix from Wolfram Sang: "Just one I2C driver update this time" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: mediatek: Move suspend and resume handling to NOIRQ phase
| * | | | | | i2c: mediatek: Move suspend and resume handling to NOIRQ phaseQii Wang2021-01-281-3/+16
| | |_|_|_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some i2c device driver indirectly uses I2C driver when it is now being suspended. The i2c devices driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the I2C controller driver to the NOIRQ phase as well. Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
* | | | | | Merge branch 'for-rc-5.11' of ↵Linus Torvalds2021-01-319-8/+542
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds Pull LED fixes from Pavel Machek: "This pull is due to 'leds: trigger: fix potential deadlock with libata' -- people find the warn annoying. It also contains new driver and two trivial fixes" * 'for-rc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: leds: rt8515: Add Richtek RT8515 LED driver dt-bindings: leds: Add DT binding for Richtek RT8515 leds: trigger: fix potential deadlock with libata leds: leds-ariel: convert comma to semicolon leds: leds-lm3533: convert comma to semicolon
| * | | | | | leds: rt8515: Add Richtek RT8515 LED driverLinus Walleij2021-01-315-0/+421
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a driver for the Richtek RT8515 dual channel torch/flash white LED driver. This LED driver is found in some mobile phones from Samsung such as the GT-S7710 and GT-I8190. A V4L interface is added. We do not have a proper datasheet for the RT8515 but it turns out that RT9387A has a public datasheet and is essentially the same chip. We designed the driver in accordance with this datasheet. The day someone needs to drive a RT9387A this driver can probably easily be augmented to handle that chip too. Sakari Ailus, Pavel Machek and Andy Shevchenko helped significantly in getting this driver right. Cc: Sakari Ailus <sakari.ailus@iki.fi> Cc: newbytee@protonmail.com Cc: Stephan Gerhold <stephan@gerhold.net> Cc: linux-media@vger.kernel.org Cc: phone-devel@vger.kernel.org Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Pavel Machek <pavel@ucw.cz>
| * | | | | | dt-bindings: leds: Add DT binding for Richtek RT8515Linus Walleij2021-01-311-0/+111
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a YAML devicetree binding for the Richtek RT8515 dual channel flash/torch LED driver. Cc: Sakari Ailus <sakari.ailus@iki.fi> Cc: newbytee@protonmail.com Cc: Stephan Gerhold <stephan@gerhold.net> Cc: phone-devel@vger.kernel.org Cc: linux-media@vger.kernel.org Cc: devicetree@vger.kernel.org Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Pavel Machek <pavel@ucw.cz>
| * | | | | | leds: trigger: fix potential deadlock with libataAndrea Righi2021-01-311-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have the following potential deadlock condition: ======================================================== WARNING: possible irq lock inversion dependency detected 5.10.0-rc2+ #25 Not tainted -------------------------------------------------------- swapper/3/0 just changed the state of lock: ffff8880063bd618 (&host->lock){-...}-{2:2}, at: ata_bmdma_interrupt+0x27/0x200 but this lock took another, HARDIRQ-READ-unsafe lock in the past: (&trig->leddev_list_lock){.+.?}-{2:2} and interrupts could create inverse lock ordering between them. other info that might help us debug this: Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&trig->leddev_list_lock); local_irq_disable(); lock(&host->lock); lock(&trig->leddev_list_lock); <Interrupt> lock(&host->lock); *** DEADLOCK *** no locks held by swapper/3/0. the shortest dependencies between 2nd lock and 1st lock: -> (&trig->leddev_list_lock){.+.?}-{2:2} ops: 46 { HARDIRQ-ON-R at: lock_acquire+0x15f/0x420 _raw_read_lock+0x42/0x90 led_trigger_event+0x2b/0x70 rfkill_global_led_trigger_worker+0x94/0xb0 process_one_work+0x240/0x560 worker_thread+0x58/0x3d0 kthread+0x151/0x170 ret_from_fork+0x1f/0x30 IN-SOFTIRQ-R at: lock_acquire+0x15f/0x420 _raw_read_lock+0x42/0x90 led_trigger_event+0x2b/0x70 kbd_bh+0x9e/0xc0 tasklet_action_common.constprop.0+0xe9/0x100 tasklet_action+0x22/0x30 __do_softirq+0xcc/0x46d run_ksoftirqd+0x3f/0x70 smpboot_thread_fn+0x116/0x1f0 kthread+0x151/0x170 ret_from_fork+0x1f/0x30 SOFTIRQ-ON-R at: lock_acquire+0x15f/0x420 _raw_read_lock+0x42/0x90 led_trigger_event+0x2b/0x70 rfkill_global_led_trigger_worker+0x94/0xb0 process_one_work+0x240/0x560 worker_thread+0x58/0x3d0 kthread+0x151/0x170 ret_from_fork+0x1f/0x30 INITIAL READ USE at: lock_acquire+0x15f/0x420 _raw_read_lock+0x42/0x90 led_trigger_event+0x2b/0x70 rfkill_global_led_trigger_worker+0x94/0xb0 process_one_work+0x240/0x560 worker_thread+0x58/0x3d0 kthread+0x151/0x170 ret_from_fork+0x1f/0x30 } ... key at: [<ffffffff83da4c00>] __key.0+0x0/0x10 ... acquired at: _raw_read_lock+0x42/0x90 led_trigger_blink_oneshot+0x3b/0x90 ledtrig_disk_activity+0x3c/0xa0 ata_qc_complete+0x26/0x450 ata_do_link_abort+0xa3/0xe0 ata_port_freeze+0x2e/0x40 ata_hsm_qc_complete+0x94/0xa0 ata_sff_hsm_move+0x177/0x7a0 ata_sff_pio_task+0xc7/0x1b0 process_one_work+0x240/0x560 worker_thread+0x58/0x3d0 kthread+0x151/0x170 ret_from_fork+0x1f/0x30 -> (&host->lock){-...}-{2:2} ops: 69 { IN-HARDIRQ-W at: lock_acquire+0x15f/0x420 _raw_spin_lock_irqsave+0x52/0xa0 ata_bmdma_interrupt+0x27/0x200 __handle_irq_event_percpu+0xd5/0x2b0 handle_irq_event+0x57/0xb0 handle_edge_irq+0x8c/0x230 asm_call_irq_on_stack+0xf/0x20 common_interrupt+0x100/0x1c0 asm_common_interrupt+0x1e/0x40 native_safe_halt+0xe/0x10 arch_cpu_idle+0x15/0x20 default_idle_call+0x59/0x1c0 do_idle+0x22c/0x2c0 cpu_startup_entry+0x20/0x30 start_secondary+0x11d/0x150 secondary_startup_64_no_verify+0xa6/0xab INITIAL USE at: lock_acquire+0x15f/0x420 _raw_spin_lock_irqsave+0x52/0xa0 ata_dev_init+0x54/0xe0 ata_link_init+0x8b/0xd0 ata_port_alloc+0x1f1/0x210 ata_host_alloc+0xf1/0x130 ata_host_alloc_pinfo+0x14/0xb0 ata_pci_sff_prepare_host+0x41/0xa0 ata_pci_bmdma_prepare_host+0x14/0x30 piix_init_one+0x21f/0x600 local_pci_probe+0x48/0x80 pci_device_probe+0x105/0x1c0 really_probe+0x221/0x490 driver_probe_device+0xe9/0x160 device_driver_attach+0xb2/0xc0 __driver_attach+0x91/0x150 bus_for_each_dev+0x81/0xc0 driver_attach+0x1e/0x20 bus_add_driver+0x138/0x1f0 driver_register+0x91/0xf0 __pci_register_driver+0x73/0x80 piix_init+0x1e/0x2e do_one_initcall+0x5f/0x2d0 kernel_init_freeable+0x26f/0x2cf kernel_init+0xe/0x113 ret_from_fork+0x1f/0x30 } ... key at: [<ffffffff83d9fdc0>] __key.6+0x0/0x10 ... acquired at: __lock_acquire+0x9da/0x2370 lock_acquire+0x15f/0x420 _raw_spin_lock_irqsave+0x52/0xa0 ata_bmdma_interrupt+0x27/0x200 __handle_irq_event_percpu+0xd5/0x2b0 handle_irq_event+0x57/0xb0 handle_edge_irq+0x8c/0x230 asm_call_irq_on_stack+0xf/0x20 common_interrupt+0x100/0x1c0 asm_common_interrupt+0x1e/0x40 native_safe_halt+0xe/0x10 arch_cpu_idle+0x15/0x20 default_idle_call+0x59/0x1c0 do_idle+0x22c/0x2c0 cpu_startup_entry+0x20/0x30 start_secondary+0x11d/0x150 secondary_startup_64_no_verify+0xa6/0xab This lockdep splat is reported after: commit e918188611f0 ("locking: More accurate annotations for read_lock()") To clarify: - read-locks are recursive only in interrupt context (when in_interrupt() returns true) - after acquiring host->lock in CPU1, another cpu (i.e. CPU2) may call write_lock(&trig->leddev_list_lock) that would be blocked by CPU0 that holds trig->leddev_list_lock in read-mode - when CPU1 (ata_ac_complete()) tries to read-lock trig->leddev_list_lock, it would be blocked by the write-lock waiter on CPU2 (because we are not in interrupt context, so the read-lock is not recursive) - at this point if an interrupt happens on CPU0 and ata_bmdma_interrupt() is executed it will try to acquire host->lock, that is held by CPU1, that is currently blocked by CPU2, so: * CPU0 blocked by CPU1 * CPU1 blocked by CPU2 * CPU2 blocked by CPU0 *** DEADLOCK *** The deadlock scenario is better represented by the following schema (thanks to Boqun Feng <boqun.feng@gmail.com> for the schema and the detailed explanation of the deadlock condition): CPU 0: CPU 1: CPU 2: ----- ----- ----- led_trigger_event(): read_lock(&trig->leddev_list_lock); <workqueue> ata_hsm_qc_complete(): spin_lock_irqsave(&host->lock); write_lock(&trig->leddev_list_lock); ata_port_freeze(): ata_do_link_abort(): ata_qc_complete(): ledtrig_disk_activity(): led_trigger_blink_oneshot(): read_lock(&trig->leddev_list_lock); // ^ not in in_interrupt() context, so could get blocked by CPU 2 <interrupt> ata_bmdma_interrupt(): spin_lock_irqsave(&host->lock); Fix by using read_lock_irqsave/irqrestore() in led_trigger_event(), so that no interrupt can happen in between, preventing the deadlock condition. Apply the same change to led_trigger_blink_setup() as well, since the same deadlock scenario can also happen in power_supply_update_bat_leds() -> led_trigger_blink() -> led_trigger_blink_setup() (workqueue context), and potentially prevent other similar usages. Link: https://lore.kernel.org/lkml/20201101092614.GB3989@xps-13-7390/ Fixes: eb25cb9956cc ("leds: convert IDE trigger to common disk trigger") Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Pavel Machek <pavel@ucw.cz>
| * | | | | | leds: leds-ariel: convert comma to semicolonZheng Yongjun2021-01-311-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Reviewed-by: Alexander Dahl <ada@thorsis.com> Signed-off-by: Pavel Machek <pavel@ucw.cz>
| * | | | | | leds: leds-lm3533: convert comma to semicolonZheng Yongjun2021-01-311-1/+1
| | |_|_|_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: Pavel Machek <pavel@ucw.cz>
* | | | | | Merge tag 'nfs-for-5.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds2021-01-315-85/+93
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull NFS client fixes from Trond Myklebust: - SUNRPC: Handle 0 length opaque XDR object data properly - Fix a layout segment leak in pnfs_layout_process() - pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn - pNFS/NFSv4: Improve rejection of out-of-order layouts - pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process() * tag 'nfs-for-5.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: SUNRPC: Handle 0 length opaque XDR object data properly SUNRPC: Move simple_get_bytes and simple_get_netobj into private header pNFS/NFSv4: Improve rejection of out-of-order layouts pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process() pNFS/NFSv4: Fix a layout segment leak in pnfs_layout_process()
| * | | | | | SUNRPC: Handle 0 length opaque XDR object data properlyDave Wysochanski2021-01-251-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When handling an auth_gss downcall, it's possible to get 0-length opaque object for the acceptor. In the case of a 0-length XDR object, make sure simple_get_netobj() fills in dest->data = NULL, and does not continue to kmemdup() which will set dest->data = ZERO_SIZE_PTR for the acceptor. The trace event code can handle NULL but not ZERO_SIZE_PTR for a string, and so without this patch the rpcgss_context trace event will crash the kernel as follows: [ 162.887992] BUG: kernel NULL pointer dereference, address: 0000000000000010 [ 162.898693] #PF: supervisor read access in kernel mode [ 162.900830] #PF: error_code(0x0000) - not-present page [ 162.902940] PGD 0 P4D 0 [ 162.904027] Oops: 0000 [#1] SMP PTI [ 162.905493] CPU: 4 PID: 4321 Comm: rpc.gssd Kdump: loaded Not tainted 5.10.0 #133 [ 162.908548] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 162.910978] RIP: 0010:strlen+0x0/0x20 [ 162.912505] Code: 48 89 f9 74 09 48 83 c1 01 80 39 00 75 f7 31 d2 44 0f b6 04 16 44 88 04 11 48 83 c2 01 45 84 c0 75 ee c3 0f 1f 80 00 00 00 00 <80> 3f 00 74 10 48 89 f8 48 83 c0 01 80 38 00 75 f7 48 29 f8 c3 31 [ 162.920101] RSP: 0018:ffffaec900c77d90 EFLAGS: 00010202 [ 162.922263] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00000000fffde697 [ 162.925158] RDX: 000000000000002f RSI: 0000000000000080 RDI: 0000000000000010 [ 162.928073] RBP: 0000000000000010 R08: 0000000000000e10 R09: 0000000000000000 [ 162.930976] R10: ffff8e698a590cb8 R11: 0000000000000001 R12: 0000000000000e10 [ 162.933883] R13: 00000000fffde697 R14: 000000010034d517 R15: 0000000000070028 [ 162.936777] FS: 00007f1e1eb93700(0000) GS:ffff8e6ab7d00000(0000) knlGS:0000000000000000 [ 162.940067] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 162.942417] CR2: 0000000000000010 CR3: 0000000104eba000 CR4: 00000000000406e0 [ 162.945300] Call Trace: [ 162.946428] trace_event_raw_event_rpcgss_context+0x84/0x140 [auth_rpcgss] [ 162.949308] ? __kmalloc_track_caller+0x35/0x5a0 [ 162.951224] ? gss_pipe_downcall+0x3a3/0x6a0 [auth_rpcgss] [ 162.953484] gss_pipe_downcall+0x585/0x6a0 [auth_rpcgss] [ 162.955953] rpc_pipe_write+0x58/0x70 [sunrpc] [ 162.957849] vfs_write+0xcb/0x2c0 [ 162.959264] ksys_write+0x68/0xe0 [ 162.960706] do_syscall_64+0x33/0x40 [ 162.962238] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 162.964346] RIP: 0033:0x7f1e1f1e57df Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
| * | | | | | SUNRPC: Move simple_get_bytes and simple_get_netobj into private headerDave Wysochanski2021-01-254-60/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove duplicated helper functions to parse opaque XDR objects and place inside new file net/sunrpc/auth_gss/auth_gss_internal.h. In the new file carry the license and copyright from the source file net/sunrpc/auth_gss/auth_gss.c. Finally, update the comment inside include/linux/sunrpc/xdr.h since lockd is not the only user of struct xdr_netobj. Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
| * | | | | | pNFS/NFSv4: Improve rejection of out-of-order layoutsTrond Myklebust2021-01-251-6/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a layoutget ends up being reordered w.r.t. a layoutreturn, e.g. due to a layoutget-on-open not knowing a priori which file to lock, then we must assume the layout is no longer being considered valid state by the server. Incrementally improve our ability to reject such states by using the cached old stateid in conjunction with the plh_barrier to try to identify them. Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
| * | | | | | pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturnTrond Myklebust2021-01-251-18/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we're scheduling a layoutreturn, we need to ignore any further incoming layouts with sequence ids that are going to be affected by the layout return. Fixes: 44ea8dfce021 ("NFS/pnfs: Reference the layout cred in pnfs_prepare_layoutreturn()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
| * | | | | | pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process()Trond Myklebust2021-01-251-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the server returns a new stateid that does not match the one in our cache, then try to return the one we hold instead of just invalidating it on the client side. This ensures that both client and server will agree that the stateid is invalid. Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
| * | | | | | pNFS/NFSv4: Fix a layout segment leak in pnfs_layout_process()Trond Myklebust2021-01-251-0/+1
| | |/ / / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the server returns a new stateid that does not match the one in our cache, then pnfs_layout_process() will leak the layout segments returned by pnfs_mark_layout_stateid_invalid(). Fixes: 9888d837f3cf ("pNFS: Force a retry of LAYOUTGET if the stateid doesn't match our cache") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
* | | | | | Merge tag '5.11-rc5-smb3' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds2021-01-316-20/+81
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull cifs fixes from Steve French: "Four cifs patches found in additional testing of the conversion to the new mount API: three small option processing ones, and one fixing domain based DFS referrals" * tag '5.11-rc5-smb3' of git://git.samba.org/sfrench/cifs-2.6: cifs: fix dfs domain referrals cifs: returning mount parm processing errors correctly cifs: fix mounts to subdirectories of target cifs: ignore auto and noauto options if given
| * | | | | | cifs: fix dfs domain referralsRonnie Sahlberg2021-01-296-16/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The new mount API requires additional changes to how DFS is handled. Additional testing of DFS uncovered problems with domain based DFS referrals (a follow on patch addresses DFS links) which this patch addresses. Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
| * | | | | | cifs: returning mount parm processing errors correctlySteve French2021-01-281-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During additional testing of the updated cifs.ko with the new mount API support, we found a few additional cases where we were logging errors, but not returning them to the user. For example: a) invalid security mechanisms b) invalid cache options c) unsupported rdma d) invalid smb dialect requested Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api") Acked-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com>
| * | | | | | cifs: fix mounts to subdirectories of targetSteve French2021-01-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The "prefixpath" mount option needs to be ignored which was missed in the recent conversion to the new mount API (prefixpath would be set by the mount helper if mounting a subdirectory of the root of a share e.g. //server/share/subdir) Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api") Suggested-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
| * | | | | | cifs: ignore auto and noauto options if givenAdam Harvey2021-01-281-0/+1
| |/ / / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In 24e0a1eff9e2, the noauto and auto options were missed when migrating to the new mount API. As a result, users with noauto in their fstab mount options are now unable to mount cifs filesystems, as they'll receive an "Unknown parameter" error. This restores the old behaviour of ignoring noauto and auto if they're given. Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api") Signed-off-by: Adam Harvey <adam@adamharvey.name> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com>
* | | | | | Merge tag 'scsi-fixes' of ↵Linus Torvalds2021-01-312-2/+2
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Two minor fixes in drivers. Both changing strings (one in a comment, one in a module help text) with no code impact" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: qla2xxx: Fix description for parameter ql2xenforce_iocb_limit scsi: target: iscsi: Fix typo in comment
| * | | | | | scsi: qla2xxx: Fix description for parameter ql2xenforce_iocb_limitEnzo Matsumiya2021-01-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Parameter ql2xenforce_iocb_limit is enabled by default. Link: https://lore.kernel.org/r/20210118184922.23793-1-ematsumiya@suse.de Fixes: 89c72f4245a8 ("scsi: qla2xxx: Add IOCB resource tracking") Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * | | | | | scsi: target: iscsi: Fix typo in commentValdis Klētnieks2021-01-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Correct the spelling of Nagle's name in a comment. Link: https://lore.kernel.org/r/2921.1610694423@turing-police Reviewed-by: Chaitanya Kulkarni <chiatanya.kulkarni@wdc.com> Signed-off-by: Valdis Klētnieks <valdis.kletnieks@vt.edu> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | | | | | | Merge tag 'for-linus' of git://github.com/openrisc/linuxLinus Torvalds2021-01-311-0/+1
|\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull OpenRISC fix from Stafford Horne: "Fix config dependencies for Litex SOC driver causing issues on um" * tag 'for-linus' of git://github.com/openrisc/linux: soc: litex: Properly depend on HAS_IOMEM
| * | | | | | | soc: litex: Properly depend on HAS_IOMEMDavid Gow2021-01-291-0/+1
| | |/ / / / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The LiteX SOC controller driver makes use of IOMEM functions like devm_platform_ioremap_resource(), which are only available if CONFIG_HAS_IOMEM is defined. This causes the driver to be enable under make ARCH=um allyesconfig, even though it won't build. By adding a dependency on HAS_IOMEM, the driver will not be enabled on architectures which don't support it. Fixes: 22447a99c97e ("drivers/soc/litex: add LiteX SoC Controller driver") Signed-off-by: David Gow <davidgow@google.com> [shorne@gmail.com: Fix typo in commit message pointed out in review] Signed-off-by: Stafford Horne <shorne@gmail.com>
* | | | | | | Merge tag 'devicetree-fixes-for-5.11-2' of ↵Linus Torvalds2021-01-3034-67/+49
|\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux Pull devicetree fixes from Rob Herring: - Cleanups on properties with standard unit suffixes - Fix overwriting dma_range_map if there's no 'dma-ranges' property - Fix a bug when creating a /chosen node from ARM ATAGs - Add missing properties for TI j721e USB binding - Several doc reference updates due to DT schema conversions * tag 'devicetree-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: dt-bindings: Cleanup standard unit properties of/device: Update dma_range_map only when dev has valid dma-ranges ARM: zImage: atags_to_fdt: Fix node names on added root nodes dt-bindings: usb: j721e: add ranges and dma-coherent props dt-bindings:iio:adc: update adc.yaml reference dt-bindings: memory: mediatek: update mediatek,smi-larb.yaml references dt-bindings: display: mediatek: update mediatek,dpi.yaml reference ASoC: audio-graph-card: update audio-graph-card.yaml reference
| * | | | | | | dt-bindings: Cleanup standard unit propertiesRob Herring2021-01-2925-56/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped. adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints. Cc: Jean Delvare <jdelvare@suse.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Serge Semin <fancer.lancer@gmail.com> Cc: linux-hwmon@vger.kernel.org Cc: linux-i2c@vger.kernel.org Cc: linux-iio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-input@vger.kernel.org Cc: linux-mmc@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-pm@vger.kernel.org Cc: linux-rtc@vger.kernel.org Cc: linux-serial@vger.kernel.org Cc: alsa-devel@alsa-project.org Cc: linux-watchdog@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Sebastian Reichel <sre@kernel.org> # for power-supply Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio Acked-by: Alexandre TORGUE <alexandre.torgue@foss.st.com> Link: https://lore.kernel.org/r/20210128194515.743252-1-robh@kernel.org
| * | | | | | | of/device: Update dma_range_map only when dev has valid dma-rangesYong Wu2021-01-271-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit e0d072782c73 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset") always update dma_range_map even though it was already set, like in the sunxi_mbus driver. the issue is reported at [1]. This patch avoid this(Updating it only when dev has valid dma-ranges). Meanwhile, dma_range_map contains the devices' dma_ranges information, This patch moves dma_range_map before of_iommu_configure. The iommu driver may need to know the dma_address requirements of its iommu consumer devices. [1] https://lore.kernel.org/linux-arm-kernel/5c7946f3-b56e-da00-a750-be097c7ceb32@arm.com/ CC: Frank Rowand <frowand.list@gmail.com> Fixes: e0d072782c73 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset"), Suggested-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Yong Wu <yong.wu@mediatek.com> Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210119105203.15530-1-yong.wu@mediatek.com
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-30 13:08:44 +0100