| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
AML uses SystemMemory opregions to allow AML handlers to access MMIO
registers of, e.g., GPIO controllers, or access reserved regions of
memory that are owned by the firmware.
Currently, we also allow AML access to memory that is owned by the
kernel and mapped via the linear region, which does not seem to be
supported by a valid use case, and exposes the kernel's internal
state to AML methods that may be buggy and exploitable.
On arm64, ACPI support requires booting in EFI mode, and so we can cross
reference the requested region against the EFI memory map, rather than
just do a minimal check on the first page. So let's only permit regions
to be remapped by the ACPI core if
- they don't appear in the EFI memory map at all (which is the case for
most MMIO), or
- they are covered by a single region in the EFI memory map, which is not
of a type that describes memory that is given to the kernel at boot.
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20200626155832.2323789-2-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
| | |
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM OMAP fixes from Arnd Bergmann:
"The OMAP developers are particularly active at hunting down
regressions, so this is a separate branch with OMAP specific
fixes for v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks
like I only tested suspend and resume before dropping the legacy
platform data, and forgot to test it after dropping it. Turns out
the main issue was that we no longer have platform code calling
pm_runtime_suspend for DSS like we did for the legacy platform data
case, and that fix is still being discussed on the dri-devel list
and will get merged separately. The DSS related testing exposed a
pile other other display related issues that also need fixing
though":
- Fix ti-sysc optional clock handling and reset status checks for
devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested to
avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process"
* tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Few dts fixes for omaps for v5.8
Few fixes for various devices:
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
* tag 'omap-for-v5.8/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Link: https://lore.kernel.org/r/pull-1592499282-121092@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |\ |
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Since commit cd28d1d6e52e ("net: phy: at803x: Disable phy delay for
RGMII mode") the networking is broken on the BeagleBone AI which has
the AR8035 PHY for Gigabit Ethernet [0]. The fix is to switch from
phy-mode = "rgmii" to phy-mode = "rgmii-rxid".
Note: Grygorii made a similar DT fix for other AM57xx boards with a
different phy in commit 820f8a870f65 ("ARM: dts: am57xx: fix networking
on boards with ksz9031 phy").
[0] https://git.io/Jf7PX
Fixes: 520557d4854b ("ARM: dts: am5729: beaglebone-ai: adding device tree")
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
I accidentally flipped the system timer to use system clock instead of
the 32k source clock.
Fixes: 14b1925a7219 ("ARM: dts: Configure system timers for omap4")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
While testing the recent suspend and resume regressions I noticed that
duovero can still end up losing edge gpio interrupts on runtime
suspend. This causes NFSroot easily stopping working after resume on
duovero.
Let's fix the issue by using gpio level interrupts for smsc as then
the gpio interrupt state is seen by the gpio controller on resume.
Fixes: 731b409878a3 ("ARM: dts: Configure duovero for to allow core retention during idle")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
AM3358 pin mcasp0_aclkr (ZCZ ball B13) [0] is routed to P1.31 header [1]
Mode 4 of this pin is mmc0_sdwp (SD Write Protect). A signal connected
to P1.31 may accidentally trigger mmc0 write protection. To avoid this
situation, do not put mcasp0_aclkr in mode 4 (mmc0_sdwp) by default.
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#531_Expansion_Headers
Fixes: 047905376a16 (ARM: dts: Add am335x-pocketbeagle)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | |\|
| | | |
| | | |
| | | | |
Linux 5.8-rc1
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Missed sdhci patch for am3 and am4
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
* tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Move am33xx and am43xx mmc nodes to sdhci-omap driver
Link: https://lore.kernel.org/r/pull-1591637467-607254@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Move mmc nodes to be compatible with the sdhci-omap driver. The following
modifications are required for omap_hsmmc specific properties:
ti,non-removable: convert to the generic mmc non-removable
ti,needs-special-reset: co-opted into the sdhci-omap driver
ti,dual-volt: removed. Legacy property not used in am335x or am43xx
ti,needs-special-hs-handling: removed. Legacy property not used in am335x
or am43xx
Also since the sdhci-omap driver does not support runtime PM, explicitly
disable the mmc3 instance in the dtsi.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | |\ \ \ \
| | | |/ /
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This reverts commit 636338d7968e47c7f2e0b772a2a825ad932883fb.
This patch is not a proper fixes the i2c2 timeouts are still
happening in some cases.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | |\ \ \ |
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The mailbox nodes defined in various dts files have been moved to
common dra7-ipu-dsp-common.dtsi and dra74-ipu-dsp-common.dtsi files
in commit a11a2f73b32d ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes
into common files"), but the nodes were erroneously left out in the
dra7-evm-common.dtsi file. Fix this by removing these duplicate nodes.
Fixes: a11a2f73b32d ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The commit 5390130f3b28 ("ARM: dts: dra7: add timer_sys_ck entries
for IPU/DSP timers") was added to allow the OMAP clocksource timer
driver to use the clock aliases when reconfiguring the parent clock
source for the timer functional clocks after the timer_sys_ck clock
aliases got cleaned up in commit a8202cd5174d ("clk: ti: dra7: drop
unnecessary clock aliases").
The above patch however has missed adding the entries for couple of
timers (14, 15 and 16), and also added erroneously in the parent
ti-sysc nodes for couple of clocks (timers 4, 5 and 6). Fix these
properly, so that any of these timers can be used with OMAP remoteproc
IPU and DSP devices. The always-on timers 1 and 12 are not expected
to use this clock source, so they are not modified.
Fixes: 5390130f3b28 ("ARM: dts: dra7: add timer_sys_ck entries for IPU/DSP timers")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |\ \ \ |
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
AM335x TRM: Figure 16-23 define sysconfig register and soft_reset
are in first position corresponding to SYSC_OMAP4_SOFTRESET defined
in ti-sysc.h.
Fixes: 0782e8572ce4 ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
AM335x TRM: Table 2-1 defines USBSS - USB Queue Manager in memory region
0x4740 0000 to 0x4740 7FFF.
Looks like the older TRM revisions list the range from 0x5000 to 0x8000
as reserved.
Fixes: 0782e8572ce4 ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Otherwise we can get "OCP softreset timed out" warnings occasionally
at least for i2c2 on omap4 now that we check the OCP softreset completed
bit on enable.
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We must check for "dss_core" instead of "dss" to avoid also matching
also "dss_dispc". This only matters for the mixed case of data
configured in device tree but with legacy booting ti,hwmods property
still enabled.
Fixes: 8b30919a4e3c ("ARM: OMAP2+: Handle reset quirks for dynamically allocated modules")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We are currently only setting the framedonetv_irq disabled for the SoCs
that don't have it. But we are never setting it enabled for the SoCs that
have it. Let's initialized it to true by default.
Fixes: 7324a7a0d5e2 ("bus: ti-sysc: Implement display subsystem reset quirk")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We must ignore the clockactivity bit for most modules and not set it
unless specified for the module with SYSC_QUIRK_USE_CLOCKACT. Otherwise
the interface clock can be automatically gated constantly causing
unexpected performance issues.
Fixes: ae9ae12e9daa ("bus: ti-sysc: Handle clockactivity for enable and disable")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Some modules reset automatically when idled, and when re-enabled, we must
wait for the automatic OCP softreset to complete. And if optional clocks
are configured, we need to keep the clocks on while waiting for the reset
to complete.
Let's fix the issue by moving the OCP softreset code to a separate
function sysc_wait_softreset(), and call it also from sysc_enable_module()
with the optional clocks enabled.
This is based on what we're already doing for legacy platform data booting
in _enable_sysc().
Fixes: 7324a7a0d5e2 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We can currently sometimes get "RXS timed out" errors and "EOT timed out"
errors with spi transfers.
These errors can be made easy to reproduce by reading the cpcap iio
values in a loop while keeping the CPUs busy by also reading /dev/urandom.
The "RXS timed out" errors we can fix by adding spi-cpol and spi-cpha
in addition to the spi-cs-high property we already have.
The "EOT timed out" errors we can fix by increasing the spi clock rate
to 9.6 MHz. Looks similar MC13783 PMIC says it works at spi clock rates
up to 20 MHz, so let's assume we can pick any rate up to 20 MHz also
for cpcap.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Looks like we're missing flush of posted write after module enable and
disable. I've seen occasional errors accessing various modules, and it
is suspected that the lack of posted writes can also cause random reboots.
The errors we can see are similar to the one below from spi for example:
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read): Data Access
in User mode during Functional access
...
mcspi_wait_for_reg_bit
omap2_mcspi_transfer_one
spi_transfer_one_message
...
We also want to also flush posted write for disable. The clkctrl clock
disable happens after module disable, and we don't want to have the
module potentially stay active while we're trying to disable the clock.
Fixes: d59b60564cbf ("bus: ti-sysc: Add generic enable/disable functions")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The reset handling APIs for omap-prm can be invoked PM runtime which
runs in atomic context. For this to work properly, switch to atomic
iopoll version instead of the current which can sleep. Otherwise,
this throws a "BUG: scheduling while atomic" warning. Issue is seen
rather easily when CONFIG_PREEMPT is enabled.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple of bug fixes, mostly for devicetree files
NXP i.MX:
- Use correct voltage on some i.MX8M board device trees to avoid
hardware damage
- Code fixes for a compiler warning and incorrect reference counting,
both harmless.
- Fix the i.MX8M SoC driver to correctly identify imx8mp
- Fix watchdog configuration in imx6ul-kontron device tree.
Broadcom:
- A small regression fix for the Raspberry-Pi firmware driver
- A Kconfig change to use the correct timer driver on Northstar
- A DT fix for the Luxul XWC-2000 machine
- Two more DT fixes for NSP SoCs
STmicroelectronics STI
- Revert one broken patch for L2 cache configuration
ARM Versatile Express:
- Fix a regression by reverting a broken DT cleanup
TEE drivers:
- MAINTAINERS: change tee mailing list"
* tag 'arm-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
Revert "ARM: sti: Implement dummy L2 cache's write_sec"
soc: imx8m: fix build warning
ARM: imx6: add missing put_device() call in imx6q_suspend_init()
ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
soc: imx8m: Correct i.MX8MP UID fuse offset
ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
ARM: dts: NSP: Correct FA2 mailbox node
ARM: bcm2835: Fix integer overflow in rpi_firmware_print_firmware_revision()
MAINTAINERS: change tee mailing list
ARM: dts: NSP: Disable PL330 by default, add dma-coherent property
ARM: bcm: Select ARM_TIMER_SP804 for ARCH_BCM_NSP
ARM: dts: BCM5301X: Add missing memory "device_type" for Luxul XWC-2000
arm: dts: vexpress: Move mcc node back into motherboard node
|
| | |\ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8:
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
* tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx8m: fix build warning
ARM: imx6: add missing put_device() call in imx6q_suspend_init()
ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
soc: imx8m: Correct i.MX8MP UID fuse offset
ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
Link: https://lore.kernel.org/r/20200624111725.GA24312@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Fix the build warning with x86_64-randconfig
>> drivers/soc/imx/soc-imx8m.c:150:34: warning: unused variable
>> 'imx8_soc_match' [-Wunused-const-variable]
static const struct of_device_id imx8_soc_match[] = { ^
Fixes: fc40200ebf82 ("soc: imx: increase build coverage for imx8m soc driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
if of_find_device_by_node() succeed, imx6q_suspend_init() doesn't have a
corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
if of_find_device_by_node() succeed, imx_suspend_alloc_ocram() doesn't
have a corresponding put_device(). Thus add a jump target to fix the
exception handling for this function implementation.
Fixes: 1579c7b9fe01 ("ARM: imx53: Set DDR pins to high impedance when in suspend to RAM.")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Correct i.MX8MP UID fuse offset according to fuse map:
UID_LOW: 0x420
UID_HIGH: 0x430
Fixes: fc40200ebf82 ("soc: imx: increase build coverage for imx8m soc driver")
Fixes: 18f662a73862 ("soc: imx: Add i.MX8MP SoC driver support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
The WDOG_ANY signal is connected to the RESET_IN signal of the SoM
and baseboard. It is currently configured as push-pull, which means
that if some external device like a programmer wants to assert the
RESET_IN signal by pulling it to ground, it drives against the high
level WDOG_ANY output of the SoC.
To fix this we set the WDOG_ANY signal to open-drain configuration.
That way we make sure that the RESET_IN can be asserted by the
watchdog as well as by external devices.
Fixes: 1ea4b76cdfde ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
The watchdog's WDOG_ANY signal is used to trigger a POR of the SoC,
if a soft reset is issued. As the SoM hardware connects the WDOG_ANY
and the POR signals, the watchdog node itself and the pin
configuration should be part of the common SoM devicetree.
Let's move it from the baseboard's devicetree to its proper place.
Fixes: 1ea4b76cdfde ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
LDO1 and LDO2 settings are wrong and case the voltage to go above the
maximum level of 2.15V permitted by the SoC to 3.0V.
This patch is based on work done on the i.MX8M Mini-EVK which utilizes
the same fix.
Fixes: 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group
(1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups
have been supported at bd718x7-regulator driver, hence, just corrrect the
voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too.
Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mn
datasheet as the below warning log in kernel:
[ 0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV
[ 0.999196] LDO2: Bringing 800000uV into 900000-900000uV
Fixes: 3e44dd09736d ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Cc: stable@vger.kernel.org
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | |_|_|_|_|/
| | |/| | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group
(1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups
have been supported at bd718x7-regulator driver, hence, just corrrect the
voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too.
Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mm
datasheet as the below warning log in kernel:
[ 0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV
[ 0.999196] LDO2: Bringing 800000uV into 900000-900000uV
Fixes: 78cc25fa265d ("arm64: dts: imx8mm-evk: Add BD71847 PMIC")
Cc: stable@vger.kernel.org
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | |\ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM/ARM64/MIPS SoCs drivers fixes
for 5.8, please pull the following:
- Andy provides a fix for the Raspberry Pi firmware driver to print the
correct time upon boot. This is a fallout from a converstion to use
the ptT format
* tag 'arm-soc/for-5.8/drivers-fixes' of https://github.com/Broadcom/stblinux:
ARM: bcm2835: Fix integer overflow in rpi_firmware_print_firmware_revision()
Link: https://lore.kernel.org/r/20200619202250.19029-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |\ \ \ \ \ \ \
| | | |/ / / / / /
| | |/| | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Fixes Raspberry Pi firmware version output
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
| | | |/ / / / / /
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
time64_t is 64-bit width type, we are not supposed to supply lesser ones
as in the case of rpi_firmware_print_firmware_revision() after the commit
4a60f58ee002 ("ARM: bcm2835: Switch to use %ptT"). Use temporary variable
of time64_t type to correctly handle lesser types.
Fixes: 4a60f58ee002 ("ARM: bcm2835: Switch to use %ptT")
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Revieved-by: Petr Mladek <pmladek@suse.com>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Link: https://lore.kernel.org/r/20200616163139.4229-1-andriy.shevchenko@linux.intel.com
|
| | |\ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs machine/Kconfig fixes
for 5.8, please pull the following:
- Matthew adds a missing select to permit the use of the standard ARM
SP804 timers on Norsthstar Plus (NSP)
* tag 'arm-soc/for-5.8/soc-fixes' of https://github.com/Broadcom/stblinux:
ARM: bcm: Select ARM_TIMER_SP804 for ARCH_BCM_NSP
Link: https://lore.kernel.org/r/20200619202250.19029-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |/ / / / / /
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The NSP SoC includes an SP804 timer so should be enabled here.
Fixes: a0efb0d28b77 ("ARM: dts: NSP: Add SP804 Support to DT")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
| | |\ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.8, please pull the following:
- Rafal adds a missing 'device_type' property to the Luxul XWC-2000
required for the memory nodes to be correctly parsed by Linux
- Matthew provides two fixes for the NSP SoCs, one to disable the PL330
DMA controller by default since it can be left in reset by the
bootloader and the second to correct the flow accelerator mailbox node
* tag 'arm-soc/for-5.8/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Correct FA2 mailbox node
ARM: dts: NSP: Disable PL330 by default, add dma-coherent property
ARM: dts: BCM5301X: Add missing memory "device_type" for Luxul XWC-2000
Link: https://lore.kernel.org/r/20200619202250.19029-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
The FA2 mailbox is specified at 0x18025000 but should actually be
0x18025c00, length 0x400 according to socregs_nsp.h and board_bu.c. Also
the interrupt was off by one and should be GIC SPI 151 instead of 150.
Fixes: 17d517172300 ("ARM: dts: NSP: Add mailbox (PDC) to NSP")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Currently the PL330 is enabled by default. However if left in IDM reset, as is
the case with the Meraki and Synology NSP devices, the system will hang when
probing for the PL330's AMBA peripheral ID. We therefore should be able to
disable it in these cases.
The PL330 is also included among of the list of peripherals put into coherent
mode, so "dma-coherent" has been added here as well.
Fixes: 5fa1026a3e4d ("ARM: dts: NSP: Add PL330 support")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
