| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
| |
In queuecommand path, if DMA map fails, it bails out with clock held. In
this case, release the clock to keep its usage paired.
[mkp: applied by hand]
Link: https://lore.kernel.org/r/0101016ed3d66395-1b7e7fce-b74d-42ca-a88a-4db78b795d3b-000000@us-west-2.amazonses.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
UFS standard requires DBD field to be set to 1 in MODE SENSE(10).
Some card vendors are more strict and check the DBD field, hence respond
with CHECK_CONDITION (Sense key set to ILLEGAL_REQUEST and ASC set to
INVALID FIELD IN CDB). When host sends MODE SENSE for page caching, as a
result of the CHECK_CONDITION response, host assumes that the device
doesn't support the cache feature and doesn't send SYNCHRONIZE_CACHE
commands to flush the device cache. This can result in data corruption in
case of sudden power down when there is data stored in the device cache.
This patch fixes the DBD field setting as required in UFS standard.
Link: https://lore.kernel.org/r/0101016ed3d657e4-32a6dd52-1505-4312-97ff-2bd3bee59eb7-000000@us-west-2.amazonses.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
| |
UFS JEDEC standards require DBD field to be set to 1 in mode sense
command. This patch allows LLD to define the setting of DBD, if
required.
Link: https://lore.kernel.org/r/0101016ed3d643f9-ffd45d6c-c593-4a13-a18f-a32da3d3bb97-000000@us-west-2.amazonses.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In UFS host reset and restore path, before probe, we stop and start the
host controller once. After host controller is stopped, the pending
requests, if any, are cleared from the doorbell, but no completion IRQ
would be raised due to the hba is stopped. These pending requests shall be
completed along with the first NOP_OUT command (as it is the first command
which can raise a transfer completion IRQ) sent during probe. Since the
OCSs of these pending requests are not SUCCESS (because they are not yet
literally finished), their UPIUs shall be dumped. When there are multiple
pending requests, the UPIU dump can be overwhelming and may lead to
stability issues because it is in atomic context. Therefore, before probe,
complete these pending requests right after host controller is stopped and
silence the UPIU dump from them.
Link: https://lore.kernel.org/r/1574751214-8321-5-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To be on the safe side, do not touch lrb after clearing its slot in the
lrb_in_use bitmap to avoid messing up the next task which would possibly
occupy this lrb.
[mkp: applied by hand]
Link: https://lore.kernel.org/r/1574751214-8321-4-git-send-email-cang@qti.qualcomm.com
Reviewed by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Per UFS 3.0 JEDEC standard, the VCCQ2 min voltage is 1.7v and the VCCQ
voltage range is 1.14v ~ 1.26v. Update their hard codes accordingly to make
sure they work in a safe range compliant for ver 1.0/1.1/2.0/2.1/3.0 UFS
devices.
Link: https://lore.kernel.org/r/1574751214-8321-3-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
bkops level should be rechecked upon receiving an exception. Currently the
level is being cached and never updated.
Update bkops each time the level is checked. Also do not use the cached
bkops level value if it is disabled and then enabled.
Fixes: afdfff59a0e0 (scsi: ufs: handle non spec compliant bkops behaviour by device)
Link: https://lore.kernel.org/r/1574751214-8321-2-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manage TMF tags with blk_{get,put}_request() instead of
ufshcd_get_tm_free_slot() / ufshcd_put_tm_slot(). Store a per-request
completion pointer in request.end_io_data instead of using a waitqueue to
report TMF completion.
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191209181309.196233-3-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Instead of tracking which tags are in use in the ufs_hba.lrb_in_use
bitmask, rely on the block layer tag allocation mechanism. This patch
removes the following busy-waiting loop if ufshcd_issue_devman_upiu_cmd()
and the block layer accidentally allocate the same tag for a SCSI request:
* ufshcd_queuecommand() returns SCSI_MLQUEUE_HOST_BUSY.
* The SCSI core requeues the SCSI command.
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191209181309.196233-2-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The FSC (NCR53CF9x-2 / SYM53CF9x-2) has a different family code than QLogic
or Emulex parts. This caused it to be detected as a FAS100A.
Unforunately, this meant the configuration of the CONFIG3 register was
incorrect. This causes data transfer issues with FAST-SCSI targets.
The FSC also has the CONFIG4 register. It can be used to enable a feature
called Active Negation which should always be enabled according to the data
manual.
Link: https://lore.kernel.org/r/20191119202021.28720-3-jongk@linux-m68k.org
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The order of the definitions in the esp_rev enum is important. The values
are used in comparisons for chip features.
Add a comment to the enum explaining this.
Also, the actual values for the enum fields are irrelevant, so remove the
explicit values (suggested by Geert Uytterhoeven). This makes adding a new
field in the middle of the enum easier.
Finally, move the PCSCSI definition to the right place in the enum. In its
previous location, at the end of the enum, the wrong values are written to
the CONFIG3 register when used with FAST-SCSI targets.
Link: https://lore.kernel.org/r/20191119202021.28720-2-jongk@linux-m68k.org
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull rdma fixes from Doug Ledford:
"A small collection of -rc fixes. Mostly. One API addition, but that's
because we wanted to use it in a fix. There's also a bug fix that is
going to render the 5.5 kernel's soft-RoCE driver incompatible with
all soft-RoCE versions prior, but it's required to actually implement
the protocol according to the RoCE spec and required in order for the
soft-RoCE driver to be able to successfully work with actual RoCE
hardware.
Summary:
- Update Steve Wise info
- Fix for soft-RoCE crc calculations (will break back compatibility,
but only with the soft-RoCE driver, which has had this bug since it
was introduced and it is an on-the-wire bug, but will make
soft-RoCE fully compatible with real RoCE hardware)
- cma init fixup
- counters oops fix
- fix for mlx4 init/teardown sequence
- fix for mkx5 steering rules
- introduce a cleanup API, which isn't a fix, but we want to use it
in the next fix
- fix for mlx5 memory management that uses API in previous patch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix device memory flows
IB/core: Introduce rdma_user_mmap_entry_insert_range() API
IB/mlx5: Fix steering rule of drop and count
IB/mlx4: Follow mirror sequence of device add during device removal
RDMA/counter: Prevent auto-binding a QP which are not tracked with res
rxe: correctly calculate iCRC for unaligned payloads
Update mailmap info for Steve Wise
RDMA/cma: add missed unregister_pernet_subsys in init failure
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix device memory flows so that only once there will be no live mmaped
VA to a given allocation the matching object will be destroyed.
This prevents a potential scenario that existing VA that was mmaped by
one process might still be used post its deallocation despite that it's
owned now by other process.
The above is achieved by integrating with IB core APIs to manage
mmap/munmap. Only once the refcount will become 0 the DM object and its
underlay area will be freed.
Fixes: 3b113a1ec3d4 ("IB/mlx5: Support device memory type attribute")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212100237.330654-3-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Introduce rdma_user_mmap_entry_insert_range() API to be used once the
required key for the given entry should be in a given range.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212100237.330654-2-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There are two flow rule destinations: QP and packet. While users are
setting DROP packet rule, the QP should not be set as a destination.
Fixes: 3b3233fbf02e ("IB/mlx5: Add flow counters binding support")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212091214.315005-4-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Current code device add sequence is:
ib_register_device()
ib_mad_init()
init_sriov_init()
register_netdev_notifier()
Therefore, the remove sequence should be,
unregister_netdev_notifier()
close_sriov()
mad_cleanup()
ib_unregister_device()
However it is not above.
Hence, make do above remove sequence.
Fixes: fa417f7b520ee ("IB/mlx4: Add support for IBoE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212091214.315005-3-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some QPs (e.g. XRC QP) are not tracked in kernel, in this case they have
an invalid res and should not be bound to any dynamically-allocated
counter in auto mode.
This fixes below call trace:
BUG: kernel NULL pointer dereference, address: 0000000000000390
PGD 80000001a7233067 P4D 80000001a7233067 PUD 1a7215067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 2 PID: 24822 Comm: ibv_xsrq_pingpo Not tainted 5.4.0-rc5+ #21
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
RIP: 0010:rdma_counter_bind_qp_auto+0x142/0x270 [ib_core]
Code: e1 48 85 c0 48 89 c2 0f 84 bc 00 00 00 49 8b 06 48 39 42 48 75 d6 40 3a aa 90 00 00 00 75 cd 49 8b 86 00 01 00 00 48 8b 4a 28 <8b> 80 90 03 00 00 39 81 90 03 00 00 75 b4 85 c0 74 b0 48 8b 04 24
RSP: 0018:ffffc900003f39c0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: ffff88820020ec00 RSI: 0000000000000004 RDI: ffffffffffffffc0
RBP: 0000000000000001 R08: ffff888224149ff0 R09: ffffc900003f3968
R10: ffffffffffffffff R11: ffff8882249c5848 R12: ffffffffffffffff
R13: ffff88821d5aca50 R14: ffff8881f7690800 R15: ffff8881ff890000
FS: 00007fe53a3e1740(0000) GS:ffff888237b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000390 CR3: 00000001a7292006 CR4: 00000000003606a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
_ib_modify_qp+0x3a4/0x3f0 [ib_core]
? lookup_get_idr_uobject.part.8+0x23/0x40 [ib_uverbs]
modify_qp+0x322/0x3e0 [ib_uverbs]
ib_uverbs_modify_qp+0x43/0x70 [ib_uverbs]
ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0xb1/0xf0 [ib_uverbs]
ib_uverbs_run_method+0x6be/0x760 [ib_uverbs]
? uverbs_disassociate_api+0xd0/0xd0 [ib_uverbs]
ib_uverbs_cmd_verbs+0x18d/0x3a0 [ib_uverbs]
? get_acl+0x1a/0x120
? __alloc_pages_nodemask+0x15d/0x2c0
ib_uverbs_ioctl+0xa7/0x110 [ib_uverbs]
do_vfs_ioctl+0xa5/0x610
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x48/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 99fa331dc862 ("RDMA/counter: Add "auto" configuration mode support")
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Ido Kalir <idok@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212091214.315005-2-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If RoCE PDUs being sent or received contain pad bytes, then the iCRC
is miscalculated, resulting in PDUs being emitted by RXE with an incorrect
iCRC, as well as ingress PDUs being dropped due to erroneously detecting
a bad iCRC in the PDU. The fix is to include the pad bytes, if any,
in iCRC computations.
Note: This bug has caused broken on-the-wire compatibility with actual
hardware RoCE devices since the soft-RoCE driver was first put into the
mainstream kernel. Fixing it will create an incompatibility with the
original soft-RoCE devices, but is necessary to be compatible with real
hardware devices.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Steve Wise <larrystevenwise@gmail.com>
Link: https://lore.kernel.org/r/20191203020319.15036-2-larrystevenwise@gmail.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Steve Wise <larrystevenwise@gmail.com>
Link: https://lore.kernel.org/r/20191203020319.15036-1-larrystevenwise@gmail.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The driver forgets to call unregister_pernet_subsys() in the error path
of cma_init().
Add the missed call to fix it.
Fixes: 4be74b42a6d0 ("IB/cma: Separate port allocation to network namespaces")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Link: https://lore.kernel.org/r/20191206012426.12744-1-hslester96@gmail.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Two minor build fixes:
- Fix builds of the ELF loader when built with 'make -j1' (nommu
only)
- Fix CONFIG_SOC_SIFIVE builds when CONFIG_TTY is disabled (found
during randconfig testing)"
* tag 'riscv/for-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: only select serial sifive if TTY is enabled
riscv: Fix build dependency for loader
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
There is some warning if TTY is not enabled, and lead to
build error, only select serial sifive if TTY enabled, and
this also makes randconfig happy.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[paul.walmsley@sifive.com: updated to apply]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The Makefile addition for the flat image loader missed an obj prefix.
For most parallel builds this worked out fine, but with -j1 the dependency
wasn't fulfilled and thus fails:
arch/riscv/boot/loader.S: Assembler messages:
arch/riscv/boot/loader.S:7: Error: file not found: arch/riscv/boot/Image
Fixes: 405fe7aa0dba ("riscv: provide a flat image loader")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two fixes: one for a resource accounting bug in some configurations
and a fix for another patch which went into rc1"
* tag 'for-linus-5.5b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix ballooned page accounting without hotplug enabled
xen-blkback: prevent premature module unload
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When CONFIG_XEN_BALLOON_MEMORY_HOTPLUG is not defined
reserve_additional_memory() will set balloon_stats.target_pages to a
wrong value in case there are still some ballooned pages allocated via
alloc_xenballooned_pages().
This will result in balloon_process() no longer be triggered when
ballooned pages are freed in batches.
Reported-by: Nicholas Tsirakis <niko.tsirakis@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Objects allocated by xen_blkif_alloc come from the 'blkif_cache' kmem
cache. This cache is destoyed when xen-blkif is unloaded so it is
necessary to wait for the deferred free routine used for such objects to
complete. This necessity was missed in commit 14855954f636 "xen-blkback:
allow module to be cleanly unloaded". This patch fixes the problem by
taking/releasing extra module references in xen_blkif_alloc/free()
respectively.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux
Pull ksys_mount() and ksys_dup() removal from Dominik Brodowski:
"This small series replaces all in-kernel calls to the
userspace-focused ksys_mount() and ksys_dup() with calls to
kernel-centric functions:
For each replacement of ksys_mount() with do_mount(), one needs to
verify that the first and third parameter (char *dev_name, char *type)
are strings allocated in kernelspace and that the fifth parameter
(void *data) is either NULL or refers to a full page (only occurence
in init/do_mounts.c::do_mount_root()). The second and fourth
parameters (char *dir_name, unsigned long flags) are passed by
ksys_mount() to do_mount() unchanged, and therefore do not require
particular care.
Moreover, instead of pretending to be userspace, the opening of
/dev/console as stdin/stdout/stderr can be implemented using in-kernel
functions as well. Thereby, ksys_dup() can be removed for good"
[ This doesn't get rid of the special "kernel init runs with KERNEL_DS"
case, but it at least removes _some_ of the users of "treat kernel
pointers as user pointers for our magical init sequence".
One day we'll hopefully be rid of it all, and can initialize our
init_thread addr_limit to USER_DS. - Linus ]
* 'remove-ksys-mount-dup' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
fs: remove ksys_dup()
init: unify opening /dev/console as stdin/stdout/stderr
init: use do_mount() instead of ksys_mount()
initrd: use do_mount() instead of ksys_mount()
devtmpfs: use do_mount() instead of ksys_mount()
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ksys_dup() is used only at one place in the kernel, namely to duplicate
fd 0 of /dev/console to stdout and stderr. The same functionality can be
achieved by using functions already available within the kernel namespace.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Merge the two instances where /dev/console is opened as
stdin/stdout/stderr.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In prepare_namespace(), do_mount() can be used instead of ksys_mount()
as the first and third argument are const strings in the kernel, the
second and fourth argument are passed through anyway, and the fifth
argument is NULL.
In do_mount_root(), ksys_mount() is called with the first and third
argument being already kernelspace strings, which do not need to be
copied over from userspace to kernelspace (again). The second and
fourth arguments are passed through to do_mount() anyway. The fifth
argument, while already residing in kernelspace, needs to be put into
a page of its own. Then, do_mount() can be used instead of
ksys_mount().
Once this is done, there are no in-kernel users to ksys_mount() left,
which can therefore be removed.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
All three calls to ksys_mount() in initrd-related kernel code can
be switched over to do_mount():
- the first and third arguments are const strings in the kernel,
and do not need to be copied over from userspace;
- the fifth argument is NULL, and therefore no page needs to be,
copied over from userspace;
- the second and fourth argument are passed through anyway.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In devtmpfs, do_mount() can be called directly instead of complex wrapping
by ksys_mount():
- the first and third arguments are const strings in the kernel,
and do not need to be copied over from userspace;
- the fifth argument is NULL, and therefore no page needs to be
copied over from userspace;
- the second and fourth argument are passed through anyway.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fall through fix from Gustavo Silva:
"Fix compile error on sh by marking expected switch fall-through"
* tag 'Wimplicit-fallthrough-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
sh: kgdb: Mark expected switch fall-throughs
|
| | |_|/
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Mark switch cases where we are expecting to fall through.
This patch fixes the following error:
LINUX/arch/sh/kernel/kgdb.c: In function 'kgdb_arch_handle_exception':
LINUX/arch/sh/kernel/kgdb.c:267:6: error: this statement may fall through [-Werror=implicit-fallthrough=]
if (kgdb_hex2long(&ptr, &addr))
^
LINUX/arch/sh/kernel/kgdb.c:269:2: note: here
case 'D':
^~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: iscsi: Avoid potential deadlock in iscsi_if_rx func
scsi: iscsi: Fix a potential deadlock in the timeout handler
scsi: smartpqi: Update attribute name to `driver_version`
scsi: libsas: stop discovering if oob mode is disconnected
scsi: ufs: Disable autohibern8 feature in Cadence UFS
scsi: iscsi: qla4xxx: fix double free in probe
scsi: ufs: Give an unique ID to each ufs-bsg
scsi: qla2xxx: Add debug dump of LOGO payload and ELS IOCB
scsi: qla2xxx: Ignore PORT UPDATE after N2N PLOGI
scsi: qla2xxx: Don't defer relogin unconditonally
scsi: qla2xxx: Send Notify ACK after N2N PLOGI
scsi: qla2xxx: Configure local loop for N2N target
scsi: qla2xxx: Fix PLOGI payload and ELS IOCB dump length
scsi: qla2xxx: Don't call qlt_async_event twice
scsi: qla2xxx: Allow PLOGI in target mode
scsi: qla2xxx: Change discovery state before PLOGI
scsi: qla2xxx: Drop superfluous INIT_WORK of del_work
scsi: qla2xxx: Initialize free_work before flushing it
scsi: qla2xxx: Use explicit LOGO in target mode
scsi: qla2xxx: Ignore NULL pointer in tcm_qla2xxx_free_mcmd
...
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
In iscsi_if_rx func, after receiving one request through
iscsi_if_recv_msg func, iscsi_if_send_reply will be called to try to
reply to the request in a do-while loop. If the iscsi_if_send_reply
function keeps returning -EAGAIN, a deadlock will occur.
For example, a client only send msg without calling recvmsg func, then
it will result in the watchdog soft lockup. The details are given as
follows:
sock_fd = socket(AF_NETLINK, SOCK_RAW, NETLINK_ISCSI);
retval = bind(sock_fd, (struct sock addr*) & src_addr, sizeof(src_addr);
while (1) {
state_msg = sendmsg(sock_fd, &msg, 0);
//Note: recvmsg(sock_fd, &msg, 0) is not processed here.
}
close(sock_fd);
watchdog: BUG: soft lockup - CPU#7 stuck for 22s! [netlink_test:253305] Sample time: 4000897528 ns(HZ: 250) Sample stat:
curr: user: 675503481560, nice: 321724050, sys: 448689506750, idle: 4654054240530, iowait: 40885550700, irq: 14161174020, softirq: 8104324140, st: 0
deta: user: 0, nice: 0, sys: 3998210100, idle: 0, iowait: 0, irq: 1547170, softirq: 242870, st: 0 Sample softirq:
TIMER: 992
SCHED: 8
Sample irqstat:
irq 2: delta 1003, curr: 3103802, arch_timer
CPU: 7 PID: 253305 Comm: netlink_test Kdump: loaded Tainted: G OE
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
pstate: 40400005 (nZcv daif +PAN -UAO)
pc : __alloc_skb+0x104/0x1b0
lr : __alloc_skb+0x9c/0x1b0
sp : ffff000033603a30
x29: ffff000033603a30 x28: 00000000000002dd
x27: ffff800b34ced810 x26: ffff800ba7569f00
x25: 00000000ffffffff x24: 0000000000000000
x23: ffff800f7c43f600 x22: 0000000000480020
x21: ffff0000091d9000 x20: ffff800b34eff200
x19: ffff800ba7569f00 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0001000101000100
x13: 0000000101010000 x12: 0101000001010100
x11: 0001010101010001 x10: 00000000000002dd
x9 : ffff000033603d58 x8 : ffff800b34eff400
x7 : ffff800ba7569200 x6 : ffff800b34eff400
x5 : 0000000000000000 x4 : 00000000ffffffff
x3 : 0000000000000000 x2 : 0000000000000001
x1 : ffff800b34eff2c0 x0 : 0000000000000300 Call trace:
__alloc_skb+0x104/0x1b0
iscsi_if_rx+0x144/0x12bc [scsi_transport_iscsi]
netlink_unicast+0x1e0/0x258
netlink_sendmsg+0x310/0x378
sock_sendmsg+0x4c/0x70
sock_write_iter+0x90/0xf0
__vfs_write+0x11c/0x190
vfs_write+0xac/0x1c0
ksys_write+0x6c/0xd8
__arm64_sys_write+0x24/0x30
el0_svc_common+0x78/0x130
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
Link: https://lore.kernel.org/r/EDBAAA0BBBA2AC4E9C8B6B81DEEE1D6915E3D4D2@dggeml505-mbx.china.huawei.com
Signed-off-by: Bo Wu <wubo40@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Some time ago the block layer was modified such that timeout handlers are
called from thread context instead of interrupt context. Make it safe to
run the iSCSI timeout handler in thread context. This patch fixes the
following lockdep complaint:
================================
WARNING: inconsistent lock state
5.5.1-dbg+ #11 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/7:1H/206 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff88802d9827e8 (&(&session->frwd_lock)->rlock){+.?.}, at: iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_check_transport_timeouts+0x3e/0x210 [libiscsi]
call_timer_fn+0x132/0x470
__run_timers.part.0+0x39f/0x5b0
run_timer_softirq+0x63/0xc0
__do_softirq+0x12d/0x5fd
irq_exit+0xb3/0x110
smp_apic_timer_interrupt+0x131/0x3d0
apic_timer_interrupt+0xf/0x20
default_idle+0x31/0x230
arch_cpu_idle+0x13/0x20
default_idle_call+0x53/0x60
do_idle+0x38a/0x3f0
cpu_startup_entry+0x24/0x30
start_secondary+0x222/0x290
secondary_startup_64+0xa4/0xb0
irq event stamp: 1383705
hardirqs last enabled at (1383705): [<ffffffff81aace5c>] _raw_spin_unlock_irq+0x2c/0x50
hardirqs last disabled at (1383704): [<ffffffff81aacb98>] _raw_spin_lock_irq+0x18/0x50
softirqs last enabled at (1383690): [<ffffffffa0e2efea>] iscsi_queuecommand+0x76a/0xa20 [libiscsi]
softirqs last disabled at (1383682): [<ffffffffa0e2e998>] iscsi_queuecommand+0x118/0xa20 [libiscsi]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&session->frwd_lock)->rlock);
<Interrupt>
lock(&(&session->frwd_lock)->rlock);
*** DEADLOCK ***
2 locks held by kworker/7:1H/206:
#0: ffff8880d57bf928 ((wq_completion)kblockd){+.+.}, at: process_one_work+0x472/0xab0
#1: ffff88802b9c7de8 ((work_completion)(&q->timeout_work)){+.+.}, at: process_one_work+0x476/0xab0
stack backtrace:
CPU: 7 PID: 206 Comm: kworker/7:1H Not tainted 5.5.1-dbg+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0xa5/0xe6
print_usage_bug.cold+0x232/0x23b
mark_lock+0x8dc/0xa70
__lock_acquire+0xcea/0x2af0
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
scsi_times_out+0xf4/0x440 [scsi_mod]
scsi_timeout+0x1d/0x20 [scsi_mod]
blk_mq_check_expired+0x365/0x3a0
bt_iter+0xd6/0xf0
blk_mq_queue_tag_busy_iter+0x3de/0x650
blk_mq_timeout_work+0x1af/0x380
process_one_work+0x56d/0xab0
worker_thread+0x7a/0x5d0
kthread+0x1bc/0x210
ret_from_fork+0x24/0x30
Fixes: 287922eb0b18 ("block: defer timeouts to a workqueue")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191209173457.187370-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The file name in the documentation is currently incorrect, so fix it.
Link: https://lore.kernel.org/r/fe264d62-0371-ea59-b66a-6d855290ce65@molgen.mpg.de
Fixes: 6d90615f1346 ("scsi: smartpqi: add sysfs entries")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The discovering of sas port is driven by workqueue in libsas. When libsas
is processing port events or phy events in workqueue, new events may rise
up and change the state of some structures such as asd_sas_phy. This may
cause some problems such as follows:
==>thread 1 ==>thread 2
==>phy up
==>phy_up_v3_hw()
==>oob_mode = SATA_OOB_MODE;
==>phy down quickly
==>hisi_sas_phy_down()
==>sas_ha->notify_phy_event()
==>sas_phy_disconnected()
==>oob_mode = OOB_NOT_CONNECTED
==>workqueue wakeup
==>sas_form_port()
==>sas_discover_domain()
==>sas_get_port_device()
==>oob_mode is OOB_NOT_CONNECTED and device
is wrongly taken as expander
This at last lead to the panic when libsas trying to issue a command to
discover the device.
[183047.614035] Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000058
[183047.622896] Mem abort info:
[183047.625762] ESR = 0x96000004
[183047.628893] Exception class = DABT (current EL), IL = 32 bits
[183047.634888] SET = 0, FnV = 0
[183047.638015] EA = 0, S1PTW = 0
[183047.641232] Data abort info:
[183047.644189] ISV = 0, ISS = 0x00000004
[183047.648100] CM = 0, WnR = 0
[183047.651145] user pgtable: 4k pages, 48-bit VAs, pgdp =
00000000b7df67be
[183047.657834] [0000000000000058] pgd=0000000000000000
[183047.662789] Internal error: Oops: 96000004 [#1] SMP
[183047.667740] Process kworker/u16:2 (pid: 31291, stack limit =
0x00000000417c4974)
[183047.675208] CPU: 0 PID: 3291 Comm: kworker/u16:2 Tainted: G
W OE 4.19.36-vhulk1907.1.0.h410.eulerosv2r8.aarch64 #1
[183047.687015] Hardware name: N/A N/A/Kunpeng Desktop Board D920S10,
BIOS 0.15 10/22/2019
[183047.695007] Workqueue: 0000:74:02.0_disco_q sas_discover_domain
[183047.700999] pstate: 20c00009 (nzCv daif +PAN +UAO)
[183047.705864] pc : prep_ata_v3_hw+0xf8/0x230 [hisi_sas_v3_hw]
[183047.711510] lr : prep_ata_v3_hw+0xb0/0x230 [hisi_sas_v3_hw]
[183047.717153] sp : ffff00000f28ba60
[183047.720541] x29: ffff00000f28ba60 x28: ffff8026852d7228
[183047.725925] x27: ffff8027dba3e0a8 x26: ffff8027c05fc200
[183047.731310] x25: 0000000000000000 x24: ffff8026bafa8dc0
[183047.736695] x23: ffff8027c05fc218 x22: ffff8026852d7228
[183047.742079] x21: ffff80007c2f2940 x20: ffff8027c05fc200
[183047.747464] x19: 0000000000f80800 x18: 0000000000000010
[183047.752848] x17: 0000000000000000 x16: 0000000000000000
[183047.758232] x15: ffff000089a5a4ff x14: 0000000000000005
[183047.763617] x13: ffff000009a5a50e x12: ffff8026bafa1e20
[183047.769001] x11: ffff0000087453b8 x10: ffff00000f28b870
[183047.774385] x9 : 0000000000000000 x8 : ffff80007e58f9b0
[183047.779770] x7 : 0000000000000000 x6 : 000000000000003f
[183047.785154] x5 : 0000000000000040 x4 : ffffffffffffffe0
[183047.790538] x3 : 00000000000000f8 x2 : 0000000002000007
[183047.795922] x1 : 0000000000000008 x0 : 0000000000000000
[183047.801307] Call trace:
[183047.803827] prep_ata_v3_hw+0xf8/0x230 [hisi_sas_v3_hw]
[183047.809127] hisi_sas_task_prep+0x750/0x888 [hisi_sas_main]
[183047.814773] hisi_sas_task_exec.isra.7+0x88/0x1f0 [hisi_sas_main]
[183047.820939] hisi_sas_queue_command+0x28/0x38 [hisi_sas_main]
[183047.826757] smp_execute_task_sg+0xec/0x218
[183047.831013] smp_execute_task+0x74/0xa0
[183047.834921] sas_discover_expander.part.7+0x9c/0x5f8
[183047.839959] sas_discover_root_expander+0x90/0x160
[183047.844822] sas_discover_domain+0x1b8/0x1e8
[183047.849164] process_one_work+0x1b4/0x3f8
[183047.853246] worker_thread+0x54/0x470
[183047.856981] kthread+0x134/0x138
[183047.860283] ret_from_fork+0x10/0x18
[183047.863931] Code: f9407a80 528000e2 39409281 72a04002 (b9405800)
[183047.870097] kernel fault(0x1) notification starting on CPU 0
[183047.875828] kernel fault(0x1) notification finished on CPU 0
[183047.881559] Modules linked in: unibsp(OE) hns3(OE) hclge(OE)
hnae3(OE) mem_drv(OE) hisi_sas_v3_hw(OE) hisi_sas_main(OE)
[183047.892418] ---[ end trace 4cc26083fc11b783 ]---
[183047.897107] Kernel panic - not syncing: Fatal exception
[183047.902403] kernel fault(0x5) notification starting on CPU 0
[183047.908134] kernel fault(0x5) notification finished on CPU 0
[183047.913865] SMP: stopping secondary CPUs
[183047.917861] Kernel Offset: disabled
[183047.921422] CPU features: 0x2,a2a00a38
[183047.925243] Memory Limit: none
[183047.928372] kernel reboot(0x2) notification starting on CPU 0
[183047.934190] kernel reboot(0x2) notification finished on CPU 0
[183047.940008] ---[ end Kernel panic - not syncing: Fatal exception
]---
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver")
Link: https://lore.kernel.org/r/20191206011118.46909-1-yanaijie@huawei.com
Reported-by: Gao Chuan <gaochuan4@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch disables autohibern8 feature in Cadence UFS. The autohibern8
feature has issues due to which unexpected interrupt trigger is happening.
After the interrupt issue is sorted out, autohibern8 feature will be
re-enabled
Link: https://lore.kernel.org/r/1575367635-22662-1-git-send-email-sheebab@cadence.com
Cc: <stable@vger.kernel.org>
Signed-off-by: sheebab <sheebab@cadence.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->chap_dma_pool' double freed
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->fw_ddb_dma_pool' double freed
Fixes: afaf5a2d341d ("[SCSI] Initial Commit of qla4xxx")
Link: https://lore.kernel.org/r/20191203094421.hw7ex7qr3j2rbsmx@kili.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Considering there can be multiple UFS hosts in SoC, give each ufs-bsg an
unique ID by appending the scsi host number to its device name.
Link: https://lore.kernel.org/r/0101016eca8dc9d7-d24468d3-04d2-4ef3-a906-abe8b8cbcd3d-000000@us-west-2.amazonses.com
Fixes: df032bf27a41 ("scsi: ufs: Add a bsg endpoint that supports UPIUs")
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The change adds a way to debug LOGO ELS, likewise PLOGI.
Link: https://lore.kernel.org/r/20191125165702.1013-14-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Acked-by: Quinn Tran <qutran@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
PORT UPDATE asynchronous event is generated on the host that issues PLOGI
ELS (in the case of higher WWPN). In that case, the event shouldn't be
handled as it sets unwanted DPC flags (i.e. LOOP_RESYNC_NEEDED) that
trigger link flap.
Ignore the event if the host has higher WWPN, but handle otherwise.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-13-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
qla2x00_configure_local_loop sets RELOGIN_NEEDED bit and calls
qla24xx_fcport_handle_login to perform the login. This bit triggers a wake
up of DPC later after a successful login.
The deferred call is not needed if login succeeds, and it's set in
qla24xx_fcport_handle_login in case of errors, hence it should be safe to
drop.
Link: https://lore.kernel.org/r/20191125165702.1013-12-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Acked-by: Quinn Tran <qutran@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
qlt_handle_login schedules session for deletion even if a login is in
progress. That causes login bouncing, i.e. a few logins are made before it
settles down.
Complete the first login by sending Notify Acknowledge IOCB via
qlt_plogi_ack_unref if the session is pending login completion.
Fixes: 9cd883f07a54 ("scsi: qla2xxx: Fix session cleanup for N2N")
Cc: Krishna Kant <krishna.kant@purestorage.com>
Cc: Alexei Potashnik <alexei@purestorage.com>
Link: https://lore.kernel.org/r/20191125165702.1013-11-r.bolshakov@yadro.com
Acked-by: Quinn Tran <qutran@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad099074 ("scsi: qla2xxx: Fix N2N link re-connect")
Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com
Acked-by: Quinn Tran <qutran@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The size of the buffer is hardcoded as 0x70 or 112 bytes, while the size of
ELS IOCB is 0x40 and the size of PLOGI payload returned by Get Parameters
command is 0x74.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-9-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
MBA_PORT_UPDATE generates duplicate log lines in target mode because
qlt_async_event is called twice. Drop the calls within the case as the
function will be called right after the switch statement.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-8-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|