summaryrefslogtreecommitdiffstats
path: root/Documentation/blockdev/00-INDEX (follow)
Commit message (Collapse)AuthorAgeFilesLines
* Drop all 00-INDEX files from Documentation/Henrik Austad2018-09-091-18/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a respin with a wider audience (all that get_maintainer returned) and I know this spams a *lot* of people. Not sure what would be the correct way, so my apologies for ruining your inbox. The 00-INDEX files are supposed to give a summary of all files present in a directory, but these files are horribly out of date and their usefulness is brought into question. Often a simple "ls" would reveal the same information as the filenames are generally quite descriptive as a short introduction to what the file covers (it should not surprise anyone what Documentation/sched/sched-design-CFS.txt covers) A few years back it was mentioned that these files were no longer really needed, and they have since then grown further out of date, so perhaps it is time to just throw them out. A short status yields the following _outdated_ 00-INDEX files, first counter is files listed in 00-INDEX but missing in the directory, last is files present but not listed in 00-INDEX. List of outdated 00-INDEX: Documentation: (4/10) Documentation/sysctl: (0/1) Documentation/timers: (1/0) Documentation/blockdev: (3/1) Documentation/w1/slaves: (0/1) Documentation/locking: (0/1) Documentation/devicetree: (0/5) Documentation/power: (1/1) Documentation/powerpc: (0/5) Documentation/arm: (1/0) Documentation/x86: (0/9) Documentation/x86/x86_64: (1/1) Documentation/scsi: (4/4) Documentation/filesystems: (2/9) Documentation/filesystems/nfs: (0/2) Documentation/cgroup-v1: (0/2) Documentation/kbuild: (0/4) Documentation/spi: (1/0) Documentation/virtual/kvm: (1/0) Documentation/scheduler: (0/2) Documentation/fb: (0/1) Documentation/block: (0/1) Documentation/networking: (6/37) Documentation/vm: (1/3) Then there are 364 subdirectories in Documentation/ with several files that are missing 00-INDEX alltogether (and another 120 with a single file and no 00-INDEX). I don't really have an opinion to whether or not we /should/ have 00-INDEX, but the above 00-INDEX should either be removed or be kept up to date. If we should keep the files, I can try to keep them updated, but I rather not if we just want to delete them anyway. As a starting point, remove all index-files and references to 00-INDEX and see where the discussion is going. Signed-off-by: Henrik Austad <henrik@austad.us> Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Just-do-it-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Jens Axboe <axboe@kernel.dk> Acked-by: Paul Moore <paul@paul-moore.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: [Almost everybody else] Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* mflash: initial supportunsik Kim2009-04-071-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver supports mflash IO mode for linux. Mflash is embedded flash drive and mainly targeted mobile and consumer electronic devices. Internally, mflash has nand flash and other hardware logics and supports 2 different operation (ATA, IO) modes. ATA mode doesn't need any new driver and currently works well under standard IDE subsystem. Actually it's one chip SSD. IO mode is ATA-like custom mode for the host that doesn't have IDE interface. Followings are brief descriptions about IO mode. A. IO mode based on ATA protocol and uses some custom command. (read confirm, write confirm) B. IO mode uses SRAM bus interface. C. IO mode supports 4kB boot area, so host can boot from mflash. This driver is quitely similar to a standard ATA driver, but because of following reasons it is currently seperated with ATA layer. 1. ATA layer deals standard ATA protocol. ATA layer have many low- level device specific interface, but data transfer keeps ATA rule. But, mflash IO mode doesn't. 2. Even though currently not used in mflash driver code, mflash has some custom command and modes. (nand fusing, firmware patch, etc) If this feature supported in linux kernel, ATA layer more altered. 3. Currently PATA platform device driver doesn't support interrupt. (I'm not sure) But, mflash uses interrupt (polling mode is just for debug). 4. mflash is somewhat under-develop product. Even though some company already using mflash their own product, I think more time is needed for standardization of custom command and mode. That time (maybe October) I will talk to with ATA people. If they accept integration, I will integrate. Signed-off-by: unsik Kim <donari75@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Create/use more directory structure in the Documentation/ tree.Randy Dunlap2008-11-141-0/+16
Create Documentation/blockdev/ sub-directory and populate it. Populate the Documentation/serial/ sub-directory. Move MSI-HOWTO.txt to Documentation/PCI/. Move ioctl-number.txt to Documentation/ioctl/. Update all relevant 00-INDEX files. Update all relevant Kconfig files and source files. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>