| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Looks like this crept in, in a recent update.
Reported-by: Krzysztof Urbaniak <urban@bash.org.pl>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
If an array with 1.x metadata is assembled with the last disk missing,
md doesn't properly record the fact that the disk was missing.
This is unlikely to cause a real problem as the event count will be
different to the count on the missing disk so it won't be included in
the array. However it could still cause confusion.
So make sure we clear all the relevant slots, not just the early ones.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Now that we depend on md_update_sb to clear variable bits in
mddev->flags (rather than trying not to set them) it is important to
always call md_update_sb when appropriate.
md_check_recovery has this job but explicitly avoids it for ->external
metadata arrays. This is not longer appropraite, or needed.
However we do want to avoid taking the mddev lock if only
MD_CHANGE_PENDING is set as that is not cleared by md_update_sb for
external-metadata arrays.
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
drivers/firewire/nosy* is a stand-alone driver that does not depend on
CONFIG_FIREWIRE. Hence let make descend into drivers/firewire/ also
if that option is off.
The stand-alone driver drivers/ieee1394/init_ohci1394_dma* will soon be
moved into drivers/firewire/ too and will require the same makefile fix.
Side effect:
As mentioned in https://bugzilla.novell.com/show_bug.cgi?id=586172#c24
this influences the order in which either firewire-ohci or ohci1394 is
going to be bound to an OHCI-1394 controller in case of a modular build
of both drivers if no modprobe blacklist entries are configured.
However, a user of such a setup cannot expect deterministic behavior
anyway. The Kconfig help and the migration guide at
ieee1394.wiki.kernel.org recommend blacklist entries when a dual
IEEE 1394 stack build is being used. (The coexistence period of the two
stacks is planned to end soon.)
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The VIAFB_GET_INFO device ioctl allows unprivileged users to read 246
bytes of uninitialized stack memory, because the "reserved" member of
the viafb_ioctl_info struct declared on the stack is not altered or
zeroed before being copied back to the user. This patch takes care of
it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Tony's fix (f574c843191728d9407b766a027f779dcd27b272) has a small bug,
it incorrectly uses "r3" as a scratch register in the first of the two
unlock paths ... it is also inefficient. Optimize the fast path again.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The NXP LPC32XX processor use the same watchdog as the Philips
PNX4008 processor.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Since it may be already enabled by bootloader or some other utility. This patch
makes sure that the watchdog is disabled before any userspace daemon opens the
device. It is also required by the watchdog API.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
module_exit()
irq and reboot notifier are acquired in module_init() but never released.
They should be released correctly, otherwise reloading the module or error
during module_init() will cause a problem.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Some pcnet_cs compatible cards require an exact 16-lines match
of the ioport areas specified in CIS, but set the "iolines"
value in the CIS incorrectly. We can easily work around this
issue -- same as we do in serial_cs -- by first trying setting
iolines to the CIS-specified value, and then trying a 16-line
match.
Reported-and-tested-by: Wolfram Sang <w.sang@pengutronix.de>
Hardware-supplied-by: Jochen Frieling <j.frieling@pengutronix.de>
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
As the iomem / ioport setup differs per device, it is much better
to print out the device instead of the socket.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
We shouldn't overwrite pre-set values, and we should also
set the port address to the beginning, and not the end of
the 8-port range.
CC: linux-serial@vger.kernel.org
Reported-by: Komuro <komurojun-mbn@nifty.com>
Hardware-supplied-by: Jochen Frieling <j.frieling@pengutronix.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
This cut-and-paste bug was caused by rewriting the register dump
code to use only a single printk per line of output.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This tripped up a driver (not yet committed to git). Fix it now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
During context switch, save and restore a couple of additional bits of
tilegx user state that can be persistently modified by userspace.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Rather than just using pt_regs, it now contains the actual saved
state explicitly, similar to pt_regs. By doing it this way, we
provide a cleaner API for userspace (or equivalently, we avoid the
need for libc to provide its own definition of sigcontext).
While we're at it, move PT_FLAGS_xxx to where they are not visible
from userspace. And always pass siginfo and mcontext to signal
handlers, even if they claim they don't need it, since sometimes
they actually try to use it anyway in practice.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The sys_execve() implementation was properly const-ified but not
the declaration, the syscall wrappers, or the compat version.
This change completes the constification process.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The texture base address registers are in units of 256 bytes.
The original CS checker treated these offsets as bytes, so the
original check was wrong. I fixed the units in a patch during
the 2.6.36 cycle, but this ended up breaking some existing
userspace (probably due to a bug in either userspace texture allocation
or the drm texture mipmap checker). So for now, until we come
up with a better fix, just warn if the mipmap size it too large.
This will keep existing userspace working and it should be just
as safe as before when we were checking the wrong units. These
are GPU MC addresses, so if they fall outside of the VRAM or
GART apertures, they end up at the GPU default page, so this should
be safe from a security perspective.
v2: Just disable the warning. It just spams the log and there's
nothing the user can do about it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fix up the IRQ names for the MN10300 on-chip serial ports in the driver as
request_interrupt() no longer allows names containing slashes, giving a warning
like the following if one is encountered:
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:323 __xlate_proc_name+0x62/0x7c()
name 'ttySM0/Rx'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tavis Ormandy pointed out that do_io_submit does not do proper bounds
checking on the passed-in iocb array:
if (unlikely(nr < 0))
return -EINVAL;
if (unlikely(!access_ok(VERIFY_READ, iocbpp, (nr*sizeof(iocbpp)))))
return -EFAULT; ^^^^^^^^^^^^^^^^^^
The attached patch checks for overflow, and if it is detected, the
number of iocbs submitted is scaled down to a number that will fit in
the long. This is an ok thing to do, as sys_io_submit is documented as
returning the number of iocbs submitted, so callers should handle a
return value of less than the 'nr' argument passed in.
Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cifs_get_smb_ses must be called on a server pointer on which it holds an
active reference. It first does a search for an existing SMB session. If
it finds one, it'll put the server reference and then try to ensure that
the negprot is done, etc.
If it encounters an error at that point then it'll return an error.
There's a potential problem here though. When cifs_get_smb_ses returns
an error, the caller will also put the TCP server reference leading to a
double-put.
Fix this by having cifs_get_smb_ses only put the server reference if
it found an existing session that it could use and isn't returning an
error.
Cc: stable@kernel.org
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
In commit d4d6715, we reopened an old hole for a 64-bit ptracer touching a
32-bit tracee in system call entry. A %rax value set via ptrace at the
entry tracing stop gets used whole as a 32-bit syscall number, while we
only check the low 32 bits for validity.
Fix it by truncating %rax back to 32 bits after syscall_trace_enter,
in addition to testing the full 64 bits as has already been added.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
On 64 bits, we always, by necessity, jump through the system call
table via %rax. For 32-bit system calls, in theory the system call
number is stored in %eax, and the code was testing %eax for a valid
system call number. At one point we loaded the stored value back from
the stack to enforce zero-extension, but that was removed in checkin
d4d67150165df8bf1cc05e532f6efca96f907cab. An actual 32-bit process
will not be able to introduce a non-zero-extended number, but it can
happen via ptrace.
Instead of re-introducing the zero-extension, test what we are
actually going to use, i.e. %rax. This only adds a handful of REX
prefixes to the code.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
compat_alloc_user_space() expects the caller to independently call
access_ok() to verify the returned area. A missing call could
introduce problems on some architectures.
This patch incorporates the access_ok() check into
compat_alloc_user_space() and also adds a sanity check on the length.
The existing compat_alloc_user_space() implementations are renamed
arch_compat_alloc_user_space() and are used as part of the
implementation of the new global function.
This patch assumes NULL will cause __get_user()/__put_user() to either
fail or access userspace on all architectures. This should be
followed by checking the return value of compat_access_user_space()
for NULL in the callers, at which time the access_ok() in the callers
can also be removed.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@kernel.org>
|
|
This more or less reverts commits 08be979 (x86: Force HPET
readback_cmp for all ATI chipsets) and 30a564be (x86, hpet: Restrict
read back to affected ATI chipsets) to the status of commit 8da854c
(x86, hpet: Erratum workaround for read after write of HPET
comparator).
The delta to commit 8da854c is mostly comments and the change from
WARN_ONCE to printk_once as we know the call path of this function
already.
This needs really in depth explanation:
First of all the HPET design is a complete failure. Having a counter
compare register which generates an interrupt on matching values
forces the software to do at least one superfluous readback of the
counter register.
While it is nice in theory to program "absolute" time events it is
practically useless because the timer runs at some absurd frequency
which can never be matched to real world units. So we are forced to
calculate a relative delta and this forces a readout of the actual
counter value, adding the delta and programming the compare
register. When the delta is small enough we run into the danger that
we program a compare value which is already in the past. Due to the
compare for equal nature of HPET we need to read back the counter
value after writing the compare rehgister (btw. this is necessary for
absolute timeouts as well) to make sure that we did not miss the timer
event. We try to work around that by setting the minimum delta to a
value which is larger than the theoretical time which elapses between
the counter readout and the compare register write, but that's only
true in theory. A NMI or SMI which hits between the readout and the
write can easily push us beyond that limit. This would result in
waiting for the next HPET timer interrupt until the 32bit wraparound
of the counter happens which takes about 306 seconds.
So we designed the next event function to look like:
match = read_cnt() + delta;
write_compare_ref(match);
return read_cnt() < match ? 0 : -ETIME;
At some point we got into trouble with certain ATI chipsets. Even the
above "safe" procedure failed. The reason was that the write to the
compare register was delayed probably for performance reasons. The
theory was that they wanted to avoid the synchronization of the write
with the HPET clock, which is understandable. So the write does not
hit the compare register directly instead it goes to some intermediate
register which is copied to the real compare register in sync with the
HPET clock. That opens another window for hitting the dreaded "wait
for a wraparound" problem.
To work around that "optimization" we added a read back of the compare
register which either enforced the update of the just written value or
just delayed the readout of the counter enough to avoid the issue. We
unfortunately never got any affirmative info from ATI/AMD about this.
One thing is sure, that we nuked the performance "optimization" that
way completely and I'm pretty sure that the result is worse than
before some HW folks came up with those.
Just for paranoia reasons I added a check whether the read back
compare register value was the same as the value we wrote right
before. That paranoia check triggered a couple of years after it was
added on an Intel ICH9 chipset. Venki added a workaround (commit
8da854c) which was reading the compare register twice when the first
check failed. We considered this to be a penalty in general and
restricted the readback (thus the wasted CPU cycles) to the known to
be affected ATI chipsets.
This turned out to be a utterly wrong decision. 2.6.35 testers
experienced massive problems and finally one of them bisected it down
to commit 30a564be which spured some further investigation.
Finally we got confirmation that the write to the compare register can
be delayed by up to two HPET clock cycles which explains the problems
nicely. All we can do about this is to go back to Venki's initial
workaround in a slightly modified version.
Just for the record I need to say, that all of this could have been
avoided if hardware designers and of course the HPET committee would
have thought about the consequences for a split second. It's out of my
comprehension why designing a working timer is so hard. There are two
ways to achieve it:
1) Use a counter wrap around aware compare_reg <= counter_reg
implementation instead of the easy compare_reg == counter_reg
Downsides:
- It needs more silicon.
- It needs a readout of the counter to apply a relative
timeout. This is necessary as the counter does not run in
any useful (and adjustable) frequency and there is no
guarantee that the counter which is used for timer events is
the same which is used for reading the actual time (and
therefor for calculating the delta)
Upsides:
- None
2) Use a simple down counter for relative timer events
Downsides:
- Absolute timeouts are not possible, which is not a problem
at all in the context of an OS and the expected
max. latencies/jitter (also see Downsides of #1)
Upsides:
- It needs less or equal silicon.
- It works ALWAYS
- It is way faster than a compare register based solution (One
write versus one write plus at least one and up to four
reads)
I would not be so grumpy about all of this, if I would not have been
ignored for many years when pointing out these flaws to various
hardware folks. I really hate timers (at least those which seem to be
designed by janitors).
Though finally we got a reasonable explanation plus a solution and I
want to thank all the folks involved in chasing it down and providing
valuable input to this.
Bisected-by: Nix <nix@esperi.org.uk>
Reported-by: Artur Skawina <art.08.09@gmail.com>
Reported-by: Damien Wyart <damien.wyart@free.fr>
Reported-by: John Drescher <drescherjm@gmail.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV620
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30029
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Not 100% sure this is due to BKL removal, its most likely a combination
of that + userspace timing changes in udev/plymouth. The drm adds the sysfs
device before the driver has completed internal loading, this causes udev
to make the node and plymouth to open it before we've completed loading.
The proper solution is to delay the sysfs manipulation until later in loading
however this causes knock on issues with sysfs connector nodes, so we can use
the global mutex to serialise loading and userspace opens.
Reported-by: Toni Spets (hifi on #radeon)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
My macbook infrared remote control was broken by commit
bd25f4dd6972755579d0ea50d1a5ace2e9b00d1a ("HID: hiddev: use
usb_find_interface, get rid of BKL").
This device appears in dmesg as:
apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device
[Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
It stopped working as lircd was getting ENODEV when opening /dev/usb/hiddev0.
AFAICS hiddev_driver is a dummy driver so usb_find_interface(&hiddev_driver)
does not find anything.
The device is associated with the usbhid driver, so let's do
usb_find_interface(&hid_driver) instead.
$ ls -l /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver
lrwxrwxrwx 1 root root 0 2010-09-12 16:28 /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver -> ../../../../../../bus/usb/drivers/usbhid
Signed-off-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The arch/x86/Makefile uses scripts/gcc-x86_$(BITS)-has-stack-protector.sh
to check if cc1 supports -fstack-protector. When -fPIE is passed to cc1,
these scripts fail causing stack protection to be disabled even when it
is available.
This fix is similar to commit c47efe5548abbf53c2f66e06dcb46183b11d6b22
Reported-by: Kai Dietrich <mail@cleeus.de>
Signed-off-by: Magnus Granberg <zorry@gentoo.org>
LKML-Reference: <20100913101319.748A1148E216@opensource.dyc.edu>
Signed-off-by: Anthony G. Basile <basile@opensource.dyc.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Gcc 3.x generates a warning
arch/x86/include/asm/cpufeature.h: In function `__static_cpu_has':
arch/x86/include/asm/cpufeature.h:326: warning: asm operand 1 probably doesn't match constraints
on each file.
But static_cpu_has() for gcc 3.x does not need __static_cpu_has().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
LKML-Reference: <201008300127.o7U1RC6Z044051@www262.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
|
|
Mathieu reported bad latencies with make -j10 kind of kbuild
workloads - which is mostly caused by us scheduling with a
too coarse granularity.
Reduce the minimum granularity some more, to make sure we
can meet the latency target.
I got the following results (make -j10 kbuild load, average of 3
runs):
vanilla:
maximum latency: 38278.9 µs
average latency: 7730.1 µs
patched:
maximum latency: 22702.1 µs
average latency: 6684.8 µs
Mathieu also measured it:
|
| * wakeup-latency.c (SIGEV_THREAD) with make -j10
|
| - Mainline 2.6.35.2 kernel
|
| maximum latency: 45762.1 µs
| average latency: 7348.6 µs
|
| - With only Peter's smaller min_gran (shown below):
|
| maximum latency: 29100.6 µs
| average latency: 6684.1 µs
|
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <AANLkTi=8m4g01wZPacySoF7U0PevTNVgJoZZrHiUD-pN@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
We should not use dotlversion for the dotu inode operations
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
We should use the cached dentry operation only if caching mode is enabled
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
NULL fid should be handled in cases where we endup calling v9fs_dir_release()
before even we instantiate the fid in filp.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
This was introduced by 7cadb63d58a932041afa3f957d5cbb6ce69dcee5
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Four memory leak fixes in the 9P code.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
This commit fixes bogus CS rejection if it contains a sequence
of the following operations:
- Set the color buffer 0. track->cb[i].robj becomes non-NULL.
- Render.
- Set a larger zbuffer than the previously-set color buffer.
- Set a larger scissor area as well.
- Set the color channel mask to 0 to do depth-only rendering.
- Render. --> rejected, because track->cb[i].robj remained non-NULL,
therefore the conditional checking for the color channel mask and
friends is not performed, and the larger scissor area causes
the rejection.
This fixes bugs:
- https://bugs.freedesktop.org/show_bug.cgi?id=29762
- https://bugs.freedesktop.org/show_bug.cgi?id=28869
And maybe some others which seem to look the same.
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
One subtest of mesa/demos/gltestperf takes 9 seconds to complete,
so to prevent an unnecessary gpu reset followed by a hardlock, I am
increasing the interval to 10 seconds after which a GPU is considered
in a locked-up state. This is on RV530. However, with a little slower GPU,
we would surpass the interval easily, so this is not a good fix
for gltestperf.
Nevertheless, this commit also fixes hardlocks in the applications which
render at speed of less than 1 frame per second, where the whole frame
consists of only one command stream. The game Tiny & Big is an example.
This bar is now lowered to 0.1 fps.
Now the question comes down to whether we should (often unsuccessfully)
reset the GPU at all? Once we have stable enough drivers, we won't have to.
Has the time come already?
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch fixes rendering errors on some evergreen boards.
Hardcoding the backend map is not an optimal solution, but
a better fix is being worked on.
Similar to the fix for rv740
(6271901d828b34b27607314026deaf417f9f9b75).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29986
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Noticed while adding evergreen blit support.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Otherwise when disabling the output we switch to the new fb (which is
likely NULL) and skip the call to mode_set -- leaking driver private
state on the old_fb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
They aren't compatible.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28671
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
caused by d65d65b175a29bd7ea2bb69c046419329c4a5db7
need to update the radeon crtc priv native mode before using it.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30049
v2: integrate v/h copy paste typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
I broke out my trusty i845 and found a new boot failure, which upon
inspection turned out to be a recursion within:
drm_helper_probe_single_connector_modes() -> drm_helper_hpd_irq_event()
-> intel_crt_detect() -> drm_helper_probe_single_connector_modes()
Calling drm_kms_helper_poll_enable() instead performs the desired
re-initialisation of the polling should the user have toggled the
parameter, without the recursive side-effect.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Update copyright notice and add Documentation/workqueue.txt.
Randy Dunlap, Dave Chinner: misc fixes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-By: Florian Mickler <florian@mickler.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
|
|
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
