summaryrefslogtreecommitdiffstats
path: root/README (unfollow)
Commit message (Collapse)AuthorFilesLines
2009-06-15regulator: Set MODULE_ALIAS for regulator driversMark Brown3-0/+3
Several of the regulator drivers didn't have MODULE_ALIAS so couldn't be auto loaded. Add the MODULE_ALIAS in case they do get built as modules. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-06-15regulator: Support list_voltage for fixed voltage regulatorMark Brown1-1/+14
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-06-15regulator: Move regulator drivers to subsys_initcall()Mark Brown4-4/+4
Regulators need to be available early in init in order to allow them to be available for consumers when requested. This is generally done by registering them at subsys_initcall() time but not all regulator drivers have done that. Convert these drivers to do so in order to mimimise future support. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-06-15regulator: build fix for powerpc - renamed show_stateLiam Girdwood1-5/+5
This patch fixes the follwing build failure on powerpc:- > Today's linux-next build (powerpc allyesconfig) failed like this: > > drivers/regulator/userspace-consumer.c:43: error: conflicting types > for 'show_state' > include/linux/sched.h:273: note: previous definition of 'show_state' > was here > > Caused by commit 5defa2bce704ca4151cfe24e4297aa7797cafd22 ("regulator: > add userspace-consumer driver") which I have reverted for today. Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-06-15regulator: add userspace-consumer driverMike Rapoport4-0/+236
The userspace-consumer driver allows control of voltage and current regulator state from userspace. This is required for fine-grained power management of devices that are completely controller by userspace applications, e.g. a GPS transciever connected to a serial port. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-06-15Maxim 1586 regulator driverRobert Jarzmik4-0/+311
The Maxim 1586 regulator is a voltage regulator with 2 voltage outputs, specially suitable for Marvell PXA chips. One output is in the range of required VCC_CORE by the PXA27x chips, the other in the VCC_USIM required as well by PXA27x chips. The chip is controlled through the I2C bus. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-06-14.gitignore: ignore *.lzma filesArne Janbu1-0/+1
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14fusion: fix recent kernel-doc problemsRandy Dunlap2-4/+3
Fix recent fusion driver kernel-doc fatal error and warnings. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Eric.Moore@lsi.com Cc: support@lsi.com Cc: DL-MPTFusionLinux@lsi.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-14keyboard: advertise KT_DEAD2 extended diacriticalsSamuel Thibault1-0/+1
In addition to KT_DEAD which has limited support for diacriticals, there is KT_DEAD2 that can support 256 criticals, so let's advertise it in <linux/keyboard.h>. This lets userland know abut the drivers/char/keyboard.c function k_dead2, which supports more than the few trivial ones that k_dead supports. Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-14kbuild: add generic --set-str option to scripts/configMichal Marek1-2/+9
Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14kbuild: simplify argument loop in scripts/configMichal Marek1-28/+16
Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14kbuild: handle non-existing options in scripts/configMichal Marek1-18/+18
If an option does not exist in .config, set it at the end of the file. Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14kallsyms: generalize text region handlingMike Frysinger1-26/+61
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14kallsyms: support kernel symbols in Blackfin on-chip memoryRobin Getz1-1/+12
The Blackfin arch has a discontiguous .text layout due to having on-chip instruction memory and no virtual memory support. As such, we need to add explicit checks for these additional .text regions. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14documentation: make version fixAdam Lackorzynski1-2/+2
The Makefiles in the build directories use the internal make variable MAKEFILE_LIST which is available from make 3.80 only. (The patch would be valid back to 2.6.25) Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14kbuild: fix a compile warningAmerigo Wang1-2/+3
gcc-4.4.1: HOSTCC scripts/basic/fixdep scripts/basic/fixdep.c: In function 'traps': scripts/basic/fixdep.c:377: warning: dereferencing type-punned pointer will break strict-aliasing rules scripts/basic/fixdep.c:379: warning: dereferencing type-punned pointer will break strict-aliasing rules (Apparently -fno-strict-aliasing will fix this too) Signed-off-by: WANG Cong <amwang@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTxRoland Dreier1-1/+3
When both MSI-X and legacy INTx fail to generate an interrupt, the driver frees the MSI-X interrupts twice. Fix this by clearing the have_irq flag for the MSI-X interrupts when they are freed the first time. This is the same bug that was reported in ib_mthca by Yinghai Lu <yhlu.kernel@gmail.com>. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-06-14gitignore: Add GNU GLOBAL files to top .gitignoreJani Nikula1-0/+6
Ignore GPATH, GRTAGS, GSYMS, and GTAGS generated by GNU GLOBAL. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-06-14kbuild: fix delay in setlocalversion on readonly sourceNico Schottelius1-2/+4
Do not update index on read only media. Idea published by Christian Kujau <lists@nerdbynature.de>. Cc: Nico Schottelius <nico@ikn.schottelius.org> Cc: Christian Kujau <lists@nerdbynature.de>
2009-06-14README: fix misleading pointer to the defconf directoryPatrick Ringl1-1/+9
Signed-off-by: Patrick Ringl <patrick_@freenet.de> Cc: Arnd Bergmann <arnd@arndb.de>
2009-06-14vmlinux.lds.h updateSam Ravnborg3-16/+11
Updated after review by Tim Abbott. - Use HEAD_TEXT_SECTION - Drop use of section-names.h and delete file - Introduce EXIT_CALL Deleting section-names.h required a few simple updates of init.h Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Tim Abbott <tabbott@ksplice.com>
2009-06-14[ARM] 5545/2: add flush_kernel_dcache_page() for ARMNicolas Pitre1-0/+8
Without this, the default implementation is a no op which is completely wrong with a VIVT cache, and usage of sg_copy_buffer() produces unpredictable results. Tested-by: Sebastian Andrzej Siewior <bigeasy@breakpoint.cc> CC: stable@kernel.org Signed-off-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-14MAINTAINERS: EB110ATX is not ebsa110Russell King1-1/+0
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-14headers_check fix: mn10300, setup.hJaswinder Singh Rajput1-1/+2
fix the following 'make headers_check' warnings: usr/include/asm-mn10300/setup.h:14: extern's make no sense in userspace usr/include/asm-mn10300/setup.h:15: extern's make no sense in userspace Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
2009-06-14headers_check fix: mn10300, ptrace.hJaswinder Singh Rajput1-3/+2
fix the following 'make headers_check' warning: usr/include/asm-mn10300/ptrace.h:80: extern's make no sense in userspace Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
2009-06-14IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTxRoland Dreier1-1/+3
When both MSI-X and legacy INTx fail to generate an interrupt, the driver frees the MSI-X interrupts twice. Fix this by clearing the have_irq flag for the MSI-X interrupts when they are freed the first time. Reported-by: Yinghai Lu <yhlu.kernel@gmail.com> Tested-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-06-13atmel-mci: add MCI2 register definitionsNicolas Ferre1-0/+22
New revision of Atmel MCI interface adds new features. This is a update of register definition in header file. This new MCI IP is called MCI2. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13atmel-mci: Integrate AT91 specific definition in header fileNicolas Ferre1-0/+11
The MCI IP is shared among AVR32 and AT91 SOCs. AT91 has specific bit definitions in the user interface of MCI SD/MMC IP. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: allow compilation for ASIC3Philipp Zabel2-3/+3
Now tmio_mmc is able to drive the MMC/SD cell in ASIC3. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <spyro@f2s.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc_block: do not DMA to stackBen Dooks1-4/+12
In the write recovery routine, the data to get from the card is allocated from the stack. The DMA mapping documentation says explicitly stack memory is not mappable by any of the DMA calls. Change to using kmalloc() to allocate the memory for the result from the card and then free it once we've finished with the transaction. [ Changed to GFP_KERNEL allocation - Pierre Ossman ] Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13sdhci: Print ADMA status and pointer on debugBen Dooks1-0/+5
If using ADMA, then we should print the ADMA error and current pointer in sdhci_dumpregs() when any debug is requested. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: fix clock setupIan Molton1-10/+5
This patch fixes the clock setup in tmio_mmc. * Incorrect divider setting * Cruft written to the clock registers (seemingly harmless but Not Good (tm)) It also eliminates some unnecessary ifs and tidies the loop syntax. Thanks to Philipp Zabel who discovered the divider issue, commenting "Except for the SDCLK = HCLK (divider bypassed) case, the clock setting resulted in double the requested frequency. The smallest possible frequency (f_max/512) is configured with a divider setting 0x80, not 0x40." Signed-off-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: map SD control registers after enabling the MFD cellPhilipp Zabel1-10/+10
ASIC3 can disable the memory, so we need to wait for mfd_cell->enable to enable the memory before we can map the SD control registers. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: correct probe return value for num_resources != 3Philipp Zabel1-7/+5
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: don't use set_irq_typePhilipp Zabel1-4/+2
Use an IRQF_TRIGGER_ flag in request_irq instead. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: add bus_shift supportPhilipp Zabel2-81/+125
Some ASIC3 devices in the wild are connected with the address bus shifted by one line, so that its 16-bit registers appear 32-bit aligned in host memory space. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13MFD,mmc: tmio_mmc: make HCLK configurablePhilipp Zabel5-13/+33
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Acked-by: Samuel Ortiz <sameo@openedhand.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc_spi: don't use EINVAL for possible transmission errorsWolfgang Muees1-5/+6
This patch changes the reported error code for the responses to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved for non-recoverable host errors, and the responses from the SD/MMC card may be because of recoverable transmission errors in the command or in the response. Response codes in SPI mode are NOT protected by a checksum, so don't trust them. Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Acked-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13cb710: more cleanup for the DEBUG case.Michał Mirosław3-3/+7
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13sdhci: platform driver for SDHCIRichard Röjfors3-0/+180
Added a platform driver which uses the SDHCI core. Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mxcmmc: remove frequency workaroundPierre Ossman1-2/+0
The MMC core has now been fixed to not send silly frequencies to the drivers which means we can remove this workaround. Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13cb710: handle DEBUG define in MakefilePierre Ossman2-4/+4
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13cb710: add missing parenthesisPierre Ossman1-1/+1
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13cb710: fix printk format stringPierre Ossman1-1/+1
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc: Driver for CB710/720 memory card reader (MMC part)Michał Mirosław14-0/+1823
The code is divided in two parts. There is a virtual 'bus' driver that handles PCI device and registers three new devices one per card reader type. The other driver handles SD/MMC part of the reader. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13pxamci: add regulator support.Daniel Ribeiro1-5/+41
Changes pxamci.c to use the regulator subsystem. Uses the regulator case CONFIG_REGULATOR is defined and a matching is regulator is provided, or falls back to pdata->setpower otherwise. A warning is displayed case both a valid regulator and pdata is set, and the regulator is used. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13MMC core: limit minimum initialization frequency to 400kHzSascha Hauer1-1/+7
Some controllers allow a much lower frequency than 400kHz. Keep the minimum frequency within sensible limits. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-13sdhci: avoid changing voltage needlesslyPierre Ossman2-26/+29
Because of granularity issues, sometimes we told the hardware to change to the voltage we were already at. Rework the logic so this doesn't happen. Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc/omap: make mmci-omap using platform_driver_probeUwe Kleine-König1-2/+1
A pointer to mmc_omap_probe which lives in .init.text is passed to the core via platform_driver_register and so the kernel might oops if probe is called after the init code is discarded. As requested by David Brownell platform_driver_probe is used instead of moving the probe function to .devinit.text. This saves some memory, but might have the downside that a device being registered after the call to mmc_omap_init but before the init sections are discarded will not be bound anymore to the driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc_spi: speedup for slow cards, less wear-outWolfgang Muees1-0/+12
Speedup for slow cards by transfering more data at once. This patch also reduces the amount of wear-out of the flash blocks because fewer partial blocks are written. Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-27 06:33:20 +0100