summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/am335x-evmsk.dts (follow)
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: am335x-evmsk: Enable PRU-ICSS moduleSuman Anna2021-08-031-0/+4
| | | | | | | | | | | | | | | | The PRU-ICSS target module node was left in disabled state in the base am33xx-l4.dtsi file. PRU-ICSS is supported on the AM335x SK EVM board, so enable this node to support PRUSS on this board. The PRUSS node and most of its child nodes are already enabled in the base dts file, and so become effective automatically with the enabling of this PRU-ICSS target module node. The corresponding PRU nodes can be disabled later on if there are no use-cases defined to use a particular PRU core or the whole PRU-ICSS subsystem itself if both its PRU cores are unused. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: ti: Fix node name for all ecap dt nodesLokesh Vutla2021-06-111-1/+1
| | | | | | | | | | | dtbs_check produces the following warning for ecap node name: ecap@100: $nodename:0: 'ecap@100' does not match '^pwm(@.*|-[0-9a-f])*$' Fix this by replacing ecap with pwm in node name Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x: fix ti,no-reset-on-init flag for gpiosGrygorii Strashko2021-05-271-1/+1
| | | | | | | | | | The ti,no-reset-on-init flag need to be at the interconnect target module level for the modules that have it defined. The ti-sysc driver handles this case, but produces warning, not a critical issue. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evm/evmsk/icev2: switch to new cpsw switch drvGrygorii Strashko2020-12-011-8/+6
| | | | | | | | | | | | | The dual_mac mode has been preserved the same way between legacy and new driver, and one port devices works the same as 1 dual_mac port - it's safe to switch drivers. So, Switch amam335x-evm, am335x-evmsk and am335x-icev2 boards to use new cpsw switch driver. Those boards have or 2 Ext. port wired and configured in dual_mac mode by default, or only 1 Ext. port. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds2020-08-041-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM SoC DT updates from Arnd Bergmann: "As usual, there are many patches addressing minor issues in existing DTS files, such as DTC warnings, or adding support for additional peripherals. There are three added SoCs in existing product families: - Amazon: Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs, otherwise known as AL73400 or first-generation Graviton, and following the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips. This one is added together with the official Evaluation platform. - Qualcomm: The Snapdragon SDM630 platform is a family of mid-range mobile phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total of five end-user products are added based on these, all Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra. - Renesas: RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G family, and apparently closely related to the RZ/G2N and RZ/G2M models we already support but has a faster GPU and additional on-chip peripherals. It is added along with the HopeRun HiHope RZ/G2H development board A small number of new boards for already supported SoCs also debut: - Allwinner sunxi: Only one new machine, revision v1.2 of the Pine64 PinePhone (non-Android) smartphone, containing minor changes compared to earlier versions. - Amlogic Meson: WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box - Aspeed: EthanolX is AMD's EPYC data center rerence platform, using an ASpeed AST2600 baseboard management controller. - Mediatek: Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based on the MT8183 (Helio P60t) SoC. - Nvidia Tegra: ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android tablets from around 2012 using Tegra 3 and Tegra 2, respectively. Thanks to PostmarketOS, these can now run mainline kernels and become useful again. The Jetson Xavier NX Developer Kit uses a SoM and carrier board for the Tegra194, their latest 64-bit chip based on Carmel CPU cores and Volta graphics. - NXP i.MX: Five new boards based on the 32-bit i.MX6 series are added: The MYiR MYS-6ULX single-board computer, and four different models of industrial computers from Protonic. - Qualcomm: MikroTik RouterBoard 3011 is a rackmounted router based on the 32-bit IPQ8064 networking SoC Three older phones get added, the Snapdragon 808 (msm8992) based Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia Z5. - Renesas: In addition to the HiHope RZ/G2H board mentioned above, we gain support for board versions 3.0 and 4.0 of the earlier RZ/G2M and RZ/G2N reference boards. Beacon EmbeddedWorks adds another SoM+Carrier development board for RZ/G2M. - Rockchips: Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is based on, using the high-end 32-bit rk3288 SoC. Notable updates to existing platforms are usually for added on-chip peripherals, including: - ASpeed AST2xxx (various) - Allwinner (cpufreq, thermal, Pinephone touchscreen) - Amlogic Meson (audio, gpu dvdfs, board updates) - Arm Versatile - Broadcom (board updates for switch ports, Raspberry pi clock updates) - Hisilicon (various) - Intel/Altera SoCFPGA (various) - Marvell Armada 7xxx/8xxx (smmu) - Marvell MMP (GPU on mmp2/mmp3) - Mediatek mt8183 (USB, pericfg) - NXP Layerscape (VPU, thermal, DSPI) - NXP i.MX (VPU, bindings, board updates) - Nvidia Tegra194 (GPU) - Qualcomm (GPU, Interconnect, ...) - Renesas R-Car (SPI, IPMMU, board updates) - STMicroelectronics STM32 (various) - Samsung Exynos (various) - Socionext Uniphier (updates to serial, and pcie) - TI K3 (serdes, usb3, audio, sd, chipid) - TI OMAP (IPU/DSP remoteproc changes, dropping platform data)" * tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits) arm64: dts: meson: odroid-n2: add jack audio output support arm64: dts: meson: odroid-n2: enable audio loopback ARM: dts: berlin: Align L2 cache-controller nodename with dtschema arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree arm64: dts: qcom: msm8992: Add RPMCC node arm64: dts: qcom: msm8992: Add PSCI support. arm64: dts: qcom: msm8992: Add PMU node arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device arm64: dts: qcom: msm8992: Add a SCM node arm64: dts: qcom: msm8992: Add a proper CPU map arm64: dts: qcom: bullhead: Move UART pinctrl to SoC arm64: dts: qcom: bullhead: Add qcom,msm-id arm64: dts: qcom: msm8992: Fix SDHCI1 arm64: dts: qcom: msm8992: Modernize the DTS style arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW) arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead. arm64: dts: qcom: msm8994: Add support for SMD RPM arm64: dts: qcom: msm8992: Add a label to rpm-requests ...
| * Replace HTTP links with HTTPS ones: OMAP DEVICE TREE SUPPORTAlexander A. Klimov2020-07-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Deterministic algorithm: For each file: If not .svg: For each line: If doesn't contain `\bxmlns\b`: For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`: If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`: If both the HTTP and HTTPS versions return 200 OK and serve the same content: Replace HTTP with HTTPS. Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | ARM: dts: Move am33xx and am43xx mmc nodes to sdhci-omap driverFaiz Abbas2020-05-191-1/+1
|/ | | | | | | | | | | | | | | | | Move mmc nodes to be compatible with the sdhci-omap driver. The following modifications are required for omap_hsmmc specific properties: ti,non-removable: convert to the generic mmc non-removable ti,needs-special-reset: co-opted into the sdhci-omap driver ti,dual-volt: removed. Legacy property not used in am335x or am43xx ti,needs-special-hs-handling: removed. Legacy property not used in am335x or am43xx Also since the sdhci-omap driver does not support runtime PM, explicitly disable the mmc3 instance in the dtsi. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Use drm simple-panel instead of tilcdc-panelJyri Sarha2019-12-121-26/+12
| | | | | | | | | Move to use the new drm panel support in tilcdc together with added "newhaven,nhd-4.3-480272ef-atxl"-panel support in drm panel-simple. Signed-off-by: Jyri Sarha <jsarha@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Drop pointless status changing for am3 musbTony Lindgren2019-10-231-25/+0
| | | | | | | | | | | | The default is enabled, and there should be no need to reconfigure the status for SoC internal devices in the board specific files. Only the USB PHY used needs to be configured in the board specific files. Cc: Bin Liu <b-liu@ti.com> Cc: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner2019-06-191-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds2019-05-161-146/+146
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM Device-tree updates from Olof Johansson: "Besides new bindings and additional descriptions of hardware blocks for various SoCs and boards, the main new contents here is: SoCs: - Intel Agilex (SoCFPGA) - NXP i.MX8MM (Quad Cortex-A53 with media/graphics focus) New boards: - Allwinner: + RerVision H3-DVK (H3) + Oceanic 5205 5inMFD (H6) + Beelink GS2 (H6) + Orange Pi 3 (H6) - Rockchip: + Orange Pi RK3399 + Nanopi NEO4 + Veyron-Mighty Chromebook variant - Amlogic: + SEI Robotics SEI510 - ST Micro: + stm32mp157a discovery1 + stm32mp157c discovery2 - NXP: + Eckelmann ci4x10 (i.MX6DL) + i.MX8MM EVK (i.MX8MM) + ZII i.MX7 RPU2 (i.MX7) + ZII SPB4 (VF610) + Zii Ultra (i.MX8M) + TQ TQMa7S (i.MX7Solo) + TQ TQMa7D (i.MX7Dual) + Kobo Aura (i.MX50) + Menlosystems M53 (i.MX53)j - Nvidia: + Jetson Nano (Tegra T210)" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (593 commits) arm64: dts: bitmain: Add UART pinctrl support for Sophon Edge arm64: dts: bitmain: Add pinctrl support for BM1880 SoC arm64: dts: bitmain: Add GPIO Line names for Sophon Edge board arm64: dts: bitmain: Add GPIO support for BM1880 SoC ARM: dts: gemini: Indent DIR-685 partition table dt-bindings: hwmon (pwm-fan) Remove dead "cooling-*-state" properties ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY arm64: dts: msm8998: thermal: Restrict thermal zone name length to under 20 arm64: dts: msm8998: thermal: Fix number of supported sensors arm64: dts: msm8998-mtp: thermal: Remove skin and battery thermal zones arm64: dts: exynos: Move fixed-clocks out of soc arm64: dts: exynos: Move pmu and timer nodes out of soc ARM: dts: s5pv210: Fix camera clock provider on Goni board ARM: dts: exynos: Properly override node to use MDMA0 on Universal C210 ARM: dts: exynos: Move fixed-clocks out of soc on Exynos3250 ARM: dts: exynos: Remove unneeded address/size cells from fixed-clock on Exynos3250 ARM: dts: exynos: Move pmu and timer nodes out of soc arm64: dts: rockchip: fix IO domain voltage setting of APIO5 on rockpro64 arm64: dts: db820c: Add sound card support arm64: dts: apq8096-db820c: Add HDMI display support ...
| * ARM: dts: am335x: evmsk: Replaced register offsets with definesChristina Quast2019-04-121-146/+146
| | | | | | | | | | | | | | The defines are taken from dt-bindings/pinctrl/am33xx.h Signed-off-by: Christina Quast <cquast@hanoverdisplays.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | ARM: dts: am335x-evmsk: Correct the regulators for the audio codecPeter Ujfalusi2019-03-221-4/+22
|/ | | | | | | | | Correctly map the regulators used by tlv320aic3106. Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators. Cc: <Stable@vger.kernel.org> # v4.14+ Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Fix PHY mode for ethernetPeter Ujfalusi2019-02-191-2/+2
| | | | | | | | | | | | The PHY must add both tx and rx delay and not only on the tx clock. The board uses AR8031_AL1A PHY where the rx delay is enabled by default, the tx dealy is disabled. The reason why rgmii-txid worked because the rx delay was not disabled by the driver so essentially we ended up with rgmii-id PHY mode. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Fix ranges for am335x epwmssTony Lindgren2018-12-111-1/+1
| | | | | | | | | | Looks like I missed the ranges for am335x epwmss. Let's set it up the same way as for am437x and dra7. Fixes: 87fc89ced3a7 ("ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc") Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am33xx: convert to use new clkctrl layoutTero Kristo2018-10-181-1/+1
| | | | | | | | | Convert AM33xx to use the new clockdomain based layout. Previously the clkctrl split was based on CM instance boundaries. The new layout helps with introducing the interconnect driver instances. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: get rid of phy_id propertyGrygorii Strashko2018-09-201-2/+10
| | | | | | | The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Improve omap l4per idling with wlcore edge sensitive interruptTony Lindgren2018-07-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line: "WLAN SDIO out-of-band interrupt line. Set to rising edge (active high) by default." And it seems this interrupt can be optionally configured to use falling edge too since commit bd763482c82e ("wl18xx: wlan_irq: support platform dependent interrupt types"). On omap4, if the wlcore interrupt is configured as level instead of edge, L4PER will stop doing hardware based idling after ifconfig wlan0 down is done and the WL_EN line is pulled down. The symptoms show up with L4PER status registers no longer showing the IDLEST bits as 2 but as 0 for all the active GPIO banks and for L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in the /sys/kernel/debug/pm_debug/count. While there is also probably a GPIO related issue that needs to be still fixed, this change gets us to the point where we can have L4PER idling. I'm guessing wlcore was at some point configured to use level interrupts because of edge handling issues in gpio-omap. However, with the recent fixes to gpio-omap the edge interrupts seem to be working just fine. Let's change it for all omap boards with wlcore interrupt set as level. Cc: Dave Gerlach <d-gerlach@ti.com> Cc: Eyal Reizer <eyalr@ti.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Nishanth Menon <nm@ti.com> Cc: Tero Kristo <t-kristo@ti.com> [tony@atomide.com updated comments a bit for gpio issue] Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Add phandle for the backlight for the panelPeter Ujfalusi2018-05-151-1/+2
| | | | | | | | With the backlight phandle the driver can manage the backlight on/off in sync with the panel enable/disable. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am33xx: Add pinmux data for mmc1 in am335x-evm, evmsk and beagleboneFaiz Abbas2018-05-011-1/+8
| | | | | | | | | am335x-evm, am335x-evmsk and am335x-beaglebone are currently relying on pinmux set by the bootloader to set the correct value for mmc1. Fix this by adding pinmux data for the same in kernel. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am33xx: add clkctrl nodesTero Kristo2017-12-111-1/+1
| | | | | | | | | | | | Add clkctrl nodes for AM33xx SoC. These are going to be acting as replacement for part of the existing clock data and the existing clkctrl hooks under hwmod data. This patch also removes any obsolete clock nodes, and reroutes all users for these to use the new clkctrl clocks instead. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspendReizer, Eyal2017-03-271-0/+1
| | | | | | | | mmc2 used for wl12xx was missing the keep-power-in suspend parameter. As a result the board couldn't reach suspend state. Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am33xx: Add stdout-path propertyLokesh Vutla2017-01-201-0/+4
| | | | | | | | Add stdout-path property in /chosen node so that earlycon can be used by just adding earlycon in bootargs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: AM335X-evmsk: Add the internal and external clock nodes for rtcKeerthy2016-11-091-0/+5
| | | | | | | | | rtc can either be supplied from internal 32k clock or external crystal generated 32k clock. Internal clock is SoC specific and the external clock is board dependent. Assigning the corresponding clocks. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc nodeJyri Sarha2016-09-201-0/+2
| | | | | | | | | | | | Add blue-and-red-wiring -property to lcdc node. The am335x-evmsk has blue and red wires crossed to get 24-bit RGB (and 16-bit BGR) support. After this patch am335x-evmsk supports BGR565, RGB888, and XRGB8888 color formats. See details in Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodesJyri Sarha2016-09-201-20/+20
| | | | | | | | | Whitespace cleanup of lcdc related nodes. Do all indentation and alignment with tabs instead of spaces. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x: Add missing unit name to memory nodesJavier Martinez Canillas2016-08-311-1/+1
| | | | | | | | | This patch fixes the following DTC warnings: "Node /memory has a reg or ranges property, but no unit name" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x/437x/57xx: remove unneeded unit name for gpio-leds nodesJavier Martinez Canillas2016-08-151-4/+4
| | | | | | | | | This patch fixes the following DTC warnings for many boards: "Node /leds/led@1 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x/am437x: remove unneeded unit name for gpio-keys nodesJavier Martinez Canillas2016-08-151-5/+5
| | | | | | | | | This patch fixes the following DTC warnings for many boards: "Node /gpio_keys/button0@10 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x/am437x: remove unneeded unit name for fixed regulatorsJavier Martinez Canillas2016-08-151-4/+4
| | | | | | | | | This patch fixes the following DTC warnings for many boards: "Node /fixedregulator@0 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x: Update MPU regulator range for TI boardsDave Gerlach2016-06-101-1/+1
| | | | | | | | | | | Now that we are moving to OPPv2 bindings and able to add 1GHz OPP for MPU, let's update the max MPU voltage range to align with the maximum possible value allowed in the operating-points table, which is max target voltage of 132500 uV + 2%. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source propertySudeep Holla2015-12-171-1/+1
| | | | | | | | | | | | | | | | | Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: "Benoît Cousson" <bcousson@baylibre.com> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-omap@vger.kernel.org Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Use AM33XX_IOPAD pinmux macroJavier Martinez Canillas2015-11-301-139/+139
| | | | | | | | | | | | | Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Also, use the mux defines instead of magic numbers for the padconf values when defining the pinctrl lines to make it more readable. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x: fix cd-gpios definition as per hardware design and dt ↵Mugunthan V N2015-10-131-1/+1
| | | | | | | | | | | | | | | binding docs As per mmc device tree binding documentation card detect gpio has to be active low signal. When a hardware is designed with active high card detect, gpio polarity has to be changed with cd-inverted dt property. In AM335x the card detect gpio is designed as active low gpio. So correcting the dt card detect gpio definition. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Switch using simple-audio-card for audio supportPeter Ujfalusi2015-07-141-8/+22
| | | | | | | | The sound support consist only Headset output on the board and can be handled by "simple-audio-card" Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Add sleep pin settings for mcasp1Peter Ujfalusi2015-07-141-1/+11
| | | | | | | | When McASP is not in use the pins can be put to sleep mode to conserve power. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Fix mcasp1 node's indentationPeter Ujfalusi2015-07-141-11/+11
| | | | | | | The section had two tabs instead of one. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Fix WLAN interrupt line for AM335x EVM-SKRomain Izard2015-05-201-1/+1
| | | | | | | | | | | | | | | | | While Sitara AM335x SoCs are very close to OMAP SoCs, the 32-line GPIO controllers are numbered from 0 on AM335x and from 1 on OMAP. But when the configuration for the TI WLAN controllers was converted from platform data to device tree, this detail was overlooked, as 10 boards were using OMAP with the WL12xx and WL18xx controllers, and only one was based on AM335x. This invalid configuration prevents the WL1271 module on the AM335x EVM-SK from notifying interrupts to the SoC, and breaks the wlan driver. The DTS must be corrected to use the correct GPIO controller. Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: add wl12xx/wl18xx bindingsEliad Peller2015-03-241-0/+11
| | | | | | | | | | | | | Replace all the pdata-quirks for setting wl12xx/wl18xx platform data with proper DT definitions. Signed-off-by: Eliad Peller <eliad@wizery.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com> Tested-by: Nikita Kiryanov <nikita@compulab.co.il> Tested-by: Tony Lindgren <tony@atomide.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx into next/dtOlof Johansson2014-07-191-2/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | Merge "Xilinx Zynq changes for v3.17" from Michal Simek: arm: Xilinx Zynq dt patches for v3.17 - Document and use new cadence serial binding * tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx: ARM: zynq: DT: Migrate UART to Cadence binding tty: cadence: Document DT binding + Linux 3.16-rc5 Signed-off-by: Olof Johansson <olof@lixom.net>
| * ARM: dts: am335x-evmsk: Enable the McASP FIFO for audioPeter Ujfalusi2014-07-071-2/+2
| | | | | | | | | | | | | | | | The use of FIFO in McASP can reduce the risk of audio under/overrun and lowers the load on the memories since the DMA will operate in bursts. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | ARM: dts: am335x-evmsk: enable display and lcd panel supportDarren Etheridge2014-07-021-0/+105
|/ | | | | | | | | | | | | | | | | | | | | | Add the necessary nodes to enable the LCD controller and the LCD panel that is attached to the Texas Instruments AM335x EVMSK platform. Also setup the necessary pin mux within the DT file to drive the LCD connector and add the correct pinmux settings for the lcd pins to be configured to when the SoC goes into sleep state for the minimum power consumption. For the sleep mode LCD pin settings, MUX_MODE7 is chosen as this corresponds to switching the pins into input GPIO's with an internal pulldown. Which has been determined to offer the lowest power solution vs leaving the pins configured in LCD mode. Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Wolfram Sang <wsa@sang-engineering.com> Tested-by: Felipe Balbi <balbi@ti.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: AM33XX: fix ethernet and mdio default stateJohan Hovold2014-05-141-0/+2
| | | | | | | | Make sure ethernet and mdio nodes are disabled by default and enable them explicitly only on boards that actually use them. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: Add vtt_fixed regulatorDave Gerlach2014-05-061-0/+11
| | | | | | | | | The VTT regulator for DDR3 termination on the am335x-evmsk is controlled by a gpio. It is configured by the bootloader so here we define an always-on, fixed voltage regulator to hold the gpio. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x-evmsk: use phandles for USB and DMA refsGuido Martínez2014-05-061-19/+19
| | | | | | | | | Use phandles instead of unit adresses to reference usb and dma nodes. This makes the DT more robust and readable. Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: am335x: update USB DT referencesLeigh Brown2014-04-191-2/+2
| | | | | | | | | | | | In "ARM: dts: am33xx: correcting dt node unit address for usb", the usb_ctrl_mod and cppi41dma nodes were updated with the correct register addresses. However, the dts files that reference these nodes were not updated, and those devices are no longer being enabled. This patch corrects the references for the affected dts files. Signed-off-by: Leigh Brown <leigh@solinno.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge tag 'omap-for-v3.15/dt-overo-signed' of ↵Arnd Bergmann2014-03-171-0/+9
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Updates to the .dts files to support more Gumstix boards. These are sent separately from the rest of the .dts changes as these depend on the fixes merged into v3.14-rc4, and needed a bit more time to get updated on the fixes. * tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: Add support for the Overo Summit ARM: dts: Add support for the Overo Chestnut43 ARM: dts: Add support for the Overo Alto35 ARM: dts: Add support for the Overo Gallop43 ARM: dts: Add support for the Overo Palo43 ARM: dts: overo: Add LIS33DE accelerometer ARM: dts: overo: Create a file for common Gumstix peripherals ARM: dts: overo: Push uart3 pinmux down to expansion board ARM: dts: omap3-tobi: Add AT24C01 EEPROM ARM: dts: omap3-tobi: Use include file omap-gpmc-smsc9221 ARM: dts: omap: Add common file for SMSC9221 ARM: dts: omap3-overo: Add HSUSB PHY ARM: dts: omap3-overo: Enable WiFi/BT combo ARM: dts: omap3-overo: Add missing pinctrl ARM: dts: omap3-tobi: Add missing pinctrl ARM: dts: overo: reorganize include files Signed-off-by: Arnd Bergmann <arnd@arndb.de> Conflicts: arch/arm/boot/dts/omap3-overo.dtsi
| * ARM: dts: am335x-evmsk: Fix mmc1 supportPeter Ujfalusi2014-02-131-0/+9
| | | | | | | | | | | | | | | | Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not working on EVM-SK board. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * ARM: DTS: am335x-evmsk: Correct audio clock frequencyPeter Ujfalusi2014-02-131-1/+1
| | | | | | | | | | | | | | | | The clock for audio is sourced from virt_24000000_ck, so the correct frequency is 24000000. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | ARM: dts: am335x-evmsk: enable DMA controller for USBYegor Yefremov2014-03-121-0/+4
| | | | | | | | | | | | | | Enable DMA controller for USB Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 01:58:41 +0100