| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
| |
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\ |
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The ti,no-idle-on-init and ti,no-reset-on-init flags need to be at
the interconnect target module level for the modules that have it
defined. Otherwise we get the following warnings:
dts flag should be at module level for ti,no-idle-on-init
dts flag should be at module level for ti,no-reset-on-init
Reviewed-by: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
AM5 and DRA7 SoC families have different set of modules
in them so the SoC sepecific dtsi files need to be separated.
e.g. Some of the major differences between AM576 and DRA76
DRA76x AM576x
USB3 x
USB4 x
ATL x
VCP x
MLB x
ISS x
PRU-ICSS1 x
PRU-ICSS2 x
This patch only deals with disabling USB3, USB4 and ATL for
AM57 variants.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
| |
Convert DRA7xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
| |
Use sdhci-omap programming model based on the generic sdhci
library for programming the eMMC/SD/SDIO controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
| |
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree changes for omaps for v4.16 merge window
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
* tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
Revert "ARM: dts: dra7: Add properties to enable PCIe x2 lane mode"
ARM: dts: am572x-idk: Add cpu0 vdd supply
ARM: dts: am571x-idk: Add cpu0 vdd supply
ARM: dts: dra72-evm-tps65917: Add cpu0 vdd supply
ARM: dts: dra7-evm: Add cpu0 vdd supply
ARM: dts: am57xx-beagle-x15-common: Add cpu0 vdd supply
ARM: dts: dra7: Enable 1.5 GHz operation for the CPU
ARM: dts: dra7: Add MPU OPP supply node
ARM: dts: dra7: Add vbb-supply to cpu and additional voltages
ARM: dts: am335x-boneblue: enable can
ARM: dts: am335x-boneblue: enable usarts
ARM: dts: am335x-boneblue: fix wl1835 IRQ pin
ARM: dts: dra7: Remove deprecated PCI compatible string
ARM: dts: dra76-evm: Enable x2 PCIe lanes
ARM: dts: DRA72x: Use PCIe compatible specific to dra72
ARM: dts: DRA74x: Use PCIe compatible specific to dra74
ARM: dts: dra7: Add properties to enable PCIe x2 lane mode
ARM: dts: am57xx: Add support for am574x-idk
ARM: dts: am43x-epos-evm: Hook dcdc2 as the cpu0-supply
ARM: dts: am437x-idk-evm: Disable OPP50 for MPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |
| |
| |
| |
| |
| |
| | |
Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
| |
Add clkctrl nodes for DRA7 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
| |
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
| |
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
| |
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
10/100 Mbps"
According to errata i880 description the speed of Ethernet port 1 on AM572x
SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching
Characteristics are not compatible with 1000 Mbps operation [1].
The issue is fixed with Rev 2.0 silicon.
Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of
phy_id and apply corresponding limitation to the Ethernet Phy 1.
[1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
| |
The PMICs have POWERHOLD set by default which prevents PMIC shutdown
even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority.
So to enable pmic power off this property lets one over ride the default
value and enable pmic power off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit d20f997b4d1f ("ARM: dts: am57xx-beagle-x15: Remove pinmux
configurations for erratum i869") fat fingered a change in which
basically replaced mmc2_pinctrl_default with mmc1_pinctrl_default. And
kernel dutifully reports conflict of usage.
[...]
pinctrl-single 4a003400.pinmux: pin 4a00376c.0 already requested by
4809c000.mmc; cannot claim for 480b4000.mmc
pinctrl-single 4a003400.pinmux: pin-219 (480b4000.mmc) status -22
pinctrl-single 4a003400.pinmux: could not request pin 219 (4a00376c.0)
from group mmc1_pins_default on device pinctrl-single
omap_hsmmc 480b4000.mmc: Error applying setting, reverse things back
omap_hsmmc 480b4000.mmc: could not initialize pin control state
[...]
But, thanks to the fact that we were in fact setting all the muxes in
U-Boot, all the MMC devices were still properly detected.
Fix the typo.
Fixes: d20f997b4d1f ("ARM: dts: am57xx-beagle-x15: Remove pinmux
configurations for erratum i869")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: removed timestamps and wrapped description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.
As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.
NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.
Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.
Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file (to maintain compatibility
with existing bootloaders for A2) and the production board is now
supported as revb1.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BEAGLEBOARD_X15_REV_B1.pdf
[2] http://marc.info/?l=linux-arm-kernel&m=147273929820708&w=2
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
