| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| |
|
|
|
|
|
| |
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
exynos4210
The pinctrl pull up/down register on exynos4210 is 2-bit wide for each
pin and it accepts only values of 0, 1 and 3. The pins sd4-bus-width8
were configured with value of 4. The driver does not validate the value
so this overflow effectively set a bit 1 in adjacent pins thus
configuring them to pull down.
The author's intention was probably to set drive strength of 4x. All
other bus-widths pins are configured with pull up and drive strength of
4x. Fix this one with same pattern.
Fixes: 87711d8c7c70 ("ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
| |
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Replace duplicated macros in each DTSI file with a common macro coming
from header. Include the header in each pinctrl DTSI so further changes
could use it.
Although PIN_FUNC_SPC_2 does not bring much information about the
function itself, it still is more descriptive then hard-coded
number <2>.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
| |
Add pinctrl nodes for the HDMI CEC device to the Exynos4210 and
Exynos4x12 SoCs. These are required by the HDMI CEC device.
Signed-off-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Add pinctrl nodes for the camera parallel port CAM_A data bus
and the CAM_A_CLKOUT clock output pin.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
| |
|
|
|
|
|
|
| |
Adds pinctrl entries required by FIMD.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
| |
|
|
|
|
|
|
| |
PWM nodes are added to EXYNOS4210 pinctrl DT file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch modifies pin control groups of SD pins on EXYNOS4210
and EXYNOS4X12 to use drive strength 3 as a default value which
corresponds to S5P_GPIO_DRVSTR_LV4 in legacy non-DT code.
This is needed at least on Origen board for sdhci2 to work and
if any other drive strength is required on each board, we can
overide it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited commit message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch reworks wake-up interrupt handling in pinctrl-exynos driver,
so each pin bank, which provides wake-up interrupts, has its own IRQ
domain.
Information about whether given pin bank provides wake-up interrupts,
how many and whether they are separate or muxed are parsed from device
tree.
It gives following advantages:
- interrupts can be specified in device tree in a more readable way,
e.g. :
device {
/* ... */
interrupt-parent = <&gpx2>;
interrupts = <4 0>;
/* ... */
};
- the amount and layout of interrupts is not hardcoded in the code
anymore, but defined in SoC-specific structure
- bank and pin of each wake-up interrupt can be easily identified, to
allow operations, such as setting the pin to EINT function, from
irq_set_type() callback
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
This patch is a preparation for converting the pinctrl-samsung driver to
one GPIO chip and IRQ domain per bank. It allows particular banks to be
specified using their phandles.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
Add pinctrl driver nodes for the three instances of pin controllers
in SAMSUNG EXYNOS4210 SoC and add the pin group nodes available in the
each of those three instances.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
