summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/imx6q-ba16.dtsi (follow)
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: imx: align SPI NOR node name with dtschemaKrzysztof Kozlowski2022-04-111-1/+1
| | | | | | | The node names should be generic and SPI NOR dtschema expects "flash". Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6q-ba16: improve PHY informationSebastian Reichel2021-03-151-0/+12
| | | | | | | | | | | | | | | | Add PHY voltage supply information fixing the following kernel message: 2188000.ethernet supply phy not found, using dummy regulator Also add PHY clock information to avoid depending on the bootloader programming correct values. The bootloader also sets some reserved registers in the PHY as advised by Qualcomm, which is not supported by the bindings/kernel driver, so the reset GPIO has not been added intentionally. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6q-ba16: add USB OTG VBUS enable GPIOSebastian Reichel2021-03-151-0/+9
| | | | | | | | Add VBUS regulator GPIO information, so that USB OTG port can also be used in host mode. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: Fix the SPI chipselect polarityFabio Estevam2020-08-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The conversion of the spi-imx driver to use GPIO descriptors in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors") helped to detect the following SPI chipselect polarity mismatch on an imx6q-sabresd: [ 4.854337] m25p80@0 enforce active low on chipselect handle Prior to the above commit, the chipselect polarity passed via cs-gpios property was ignored and considered active-low. The reason for such mismatch is clearly explained in the comments inside drivers/gpio/gpiolib-of.c: * SPI children have active low chip selects * by default. This can be specified negatively * by just omitting "spi-cs-high" in the * device node, or actively by tagging on * GPIO_ACTIVE_LOW as flag in the device * tree. If the line is simultaneously * tagged as active low in the device tree * and has the "spi-cs-high" set, we get a * conflict and the "spi-cs-high" flag will * take precedence. To properly represent the SPI chipselect polarity, change it to active-low when the "spi-cs-high" property is absent. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi filesUwe Kleine-König2020-07-131-0/+1
| | | | | | | | | | | | | The imx-pwm driver supports 3 cells and this is the more flexible setting. So use it by default and overwrite it back to two for the files that reference the PWMs with just 2 cells to minimize changes. This allows to drop explicit setting to 3 cells for the boards that already depend on this. The boards that are now using 2 cells explicitly can be converted to 3 individually. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: Fix the AR803X phy-modeFabio Estevam2019-04-111-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode") exposed an issue on imx DTS files using AR8031/AR8035 PHYs. The end result is that the boards can no longer obtain an IP address via UDHCP, for example. Quoting Andrew Lunn: "The problem here is, all the DTs were broken since day 0. However, because the PHY driver was also broken, nobody noticed and it worked. Now that the PHY driver has been fixed, all the bugs in the DTs now become an issue" To fix this problem, the phy-mode property needs to be "rgmii-id", which has the following meaning as per Documentation/devicetree/bindings/net/ethernet.txt: "RGMII with internal RX and TX delays provided by the PHY, the MAC should not add the RX or TX delays in this case)" Tested on imx6-sabresd, imx6sx-sdb and imx7d-pico boards with successfully restored networking. Based on the initial submission from Steve Twiss for the imx6qdl-sabresd. Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Baruch Siach <baruch@tkos.co.il> Tested-by: Soeren Moch <smoch@web.de> Tested-by: Steve Twiss <stwiss.opensource@diasemi.com> Tested-by: Adam Thomson <Adam.Thomson@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6qdl: Fix memory node duplicationMarco Franchi2018-12-101-0/+1
| | | | | | | | | | | | | | | | | | Boards based on imx6qdl have duplicate memory nodes: - One coming from the board device tree file: memory@ - One coming from the imx6qdl.dtsi file. Fix the duplication by removing the memory node from the imx6qdl.dtsi file and by adding 'device_type = "memory";' in the board Device Tree. Converted using the following command: perl -p0777i -e 's/memory\@10000000 \{\n/memory\@10000000 \{\n\t\tdevice_type = \"memory\";\n/m' `find ./arch/arm/boot/dts -name "imx6*"`` Reported-by: Rob Herring <robh@kernel.org> Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: ba16: add "mfg" Q7 SPI-NOR partitionKen Lin2018-05-141-1/+6
| | | | | | | | | Add the 4th partiton named "mfg" with a block size 64K to store manufacturing data. Signed-off-by: Ken Lin <ken.lin@advantech.com.tw> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: Add memory node unit nameMarco Franchi2018-02-121-1/+1
| | | | | | | | | | | | | | | | | | | | Fix the following warnings from dtc by adding the unit name to memory nodes: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name Converted using the following command: perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"` The files below were manually fixed: -imx1-ads.dts -imx1-apf9328.dts -imx6q-pistachio.dts Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6: Fix PCI GPIO reset polarityFabio Estevam2017-06-071-1/+1
| | | | | | | | | | | | The imx6 PCI driver ignores the GPIO polarity from 'reset-gpio' and considers that the PCI reset is active low, unless the property 'reset-gpio-active-high' is present. Fix the device tree description by explicitly passing the 'GPIO_ACTIVE_LOW' flag to the 'reset-gpio' property. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx/vf: Correct license textAlexandre Belloni2017-01-101-5/+5
| | | | | | | | | | | | | | | The license text has been mangled at some point then copy pasted across multiple files. Restore it to what it should be. Note that this is not intended as a license change. Reviewed-by: Heiko Schocher <hs@denx.de> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Afzal Mohammed <afzal.mohd.ma@gmail.com> Acked-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: remove obsoleted property fsl,spi-num-chipselectsVladimir Zapolskiy2017-01-021-1/+0
| | | | | | | | | | | | Since commit b36581df7e78 ("spi: imx: Using existing properties for chipselects") the device tree property 'fsl,spi-num-chipselects' is unused and it is already marked as obsolete in device tree binding documentation. Remove the property from the existing DTS files to avoid its reoccurence on copying. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6qdl: don't configure reserved pad settingsUwe Kleine-König2016-08-091-12/+12
| | | | | | | | | Several dts files set a bit in the SPEED field for pads RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there doesn't have an effect and the bit reads as zero. Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: Use generic uart-has-rtscts DT propertyGeert Uytterhoeven2016-06-111-1/+1
| | | | | | | | | | | As of commit 1006ed7e1b258dac ("serial: imx: Use generic uart-has-rtscts DT property"), the Freescale IMX UART driver recognizes the generic "uart-has-rtscts" DT property, deprecating the vendor-specific "fsl,uart-has-rtscts" DT property. Hence replace the latter by the former in all DTS files. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6q-ba16: use wdog external resetAkshay Bhat2016-04-261-0/+1
| | | | | | | | | The BA16 module has a PMIC that uses the WDOG_B output from iMX6 to reset the system on a watchdog timeout. Configure the watchdog to assert the external reset signal (WDOG_B) using fsl,ext-reset-output property. Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6q-ba16: Remove unused vqmmc-supplyAkshay Bhat2016-04-131-1/+0
| | | | | | | | The vqmmc supply is not connected to bio supply on the BA16 module. Hence remove vqmmc-supply property in usdhc3 node. Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6q-ba16: Disable pwm2 by defaultJustin Waters2016-04-131-1/+1
| | | | | | | | | | | pwm2 is provided on the BA16 Q7 module, but is not used on any of the current configurations. However, future platforms may utilize this device, so we are simply disabling the node rather than removing it completely. Signed-off-by: Justin Waters <justin.waters@timeys.com> Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: ba16: Add correct PCIe Tx ValuesJustin Waters2016-04-131-0/+2
| | | | | | | | | Utilize the new PCIe Tx configuration to properly support the correct values. Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx: Add Advantech BA-16 Qseven moduleJustin Waters2016-02-291-0/+632
Add support for Advantech BA-16 module based on iMX6D processor Basic information about the module: - Module manufacturer: Advantech - CPU: Freescale ARM Cortex-A9 i.MX6 - SPECS: Up to 2GB Onboard DDR3 Memory; Up to 16GB Onboard eMMC NAND Flash Supports OpenGL ES 2.0 and OpenVG 1.1 HDMI, 24-bit LVDS 1x UART, 2x I2C, 8x GPIO, 4x Host USB 2.0 port, 1x USB OTG port, 1x micro SD (SDHC),1x SDIO, 1x SATA II, 1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2 - Website: http://goo.gl/JED98U Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>