| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
Add missing pwm-supply for regulator-vcck regulator node.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: dee51cd0d2e8 ("ARM: dts: meson8b: mxq: add the VDDEE regulator")
Fixes: d94f60e3dfa0 ("ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-3-linux.amoon@gmail.com
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The SoC temperature can be retrieved from ADC channel 8 on all 32-bit
SoCs (Meson6, Meson8, Meson8b and Meson8m2). Move the iio-hwmon instance
to meson.dtsi instead of duplicating it in all board.dts.
If the temperature sensor calibration data is missing for a board then
iio-hwmon will simply not probe.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-2-martin.blumenstingl@googlemail.com
|
|
|
|
|
|
|
|
|
|
|
|
| |
The clock controller driver has provided the XTAL clock so far. This
does not match how the hardware actually works because the XTAL clock is
an actual crystal which is mounted on the PCB.
Add the "xtal" clock to meson.dtsi and replace all references to the
clock controller's CLKID_XTAL with the new xtal clock node.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
|
|
| |
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE
supplies for example the Mali GPU and is controlled by PWM_D instead of
PWM_C.
Add the VDDEE PWM regulator and make it the supply of the Mali GPU.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
delay (the datasheet mentions: "For a complete PHY reset, this pin
must be asserted low for at least 10ms") and a 30ms deassert delay
(the datasheet mentions: "Wait for a further 30ms (for internal
circuits settling time) before accessing the PHY register"). The
old settings used 10ms for assert and 1000ms for deassert.
- IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms")). The old settings used
10ms for assert and 1000ms for deassert.
No functional changes intended.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
|
|
| |
While the text specifies "of the GPL or the X11 license" the actual
license text matches the MIT license as specified at [0]
[0] https://spdx.org/licenses/MIT.html
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The TRONFY MXQ comes with either 1GB or 2GB RAM.
Both variants share (like most boards based on Amlogic reference
designs):
- 10/100 PHY (IC Plus IP101GR) with GPIOH_4 being the reset line and
GPIOH_3 the interrupt line
- SD card slot with the card detection GPIO at CARD_6
- VCCK is generated by PWM_C with a period of 1148ns and XTAL as input
clock
- USB OTG exposed on one of the USB-A connectors
- 4-port USB hub with 3 ports exposed to the outside
There seem the multiple board revision out there according to various
forum posts:
- storage: eMMC or NAND flash
- wifi: Ampak AP6210 or Realtek 8189
Add support for the following functionality:
- SoC temperature (hwmon)
- changing the CPU voltage
- Ethernet connectivity
- SD card
- USB
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: hexdump <hexdump0815@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
|
|
|
|
|
|
|
| |
Support for this board is currently very limited. To debug any potential
issues on this board the "earlycon" kernel parameter can be used (without
any arguments). However, this requires the board to define a
/chosen/stdout-path property in it's .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|