| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Looks like we're still missing the keypad map for EVM.
Let's add it since we have the binding now available
for the twl4030_keypad as otherwise we get the following
errors during the boot:
twl4030_keypad keypad.31: OF: linux,keymap property not defined
in /ocp/i2c@48070000/twl@48/keypad
twl4030_keypad keypad.31: Failed to build keymap
twl4030_keypad: probe of keypad.31 failed with error -2
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
N900 now seems to shut down the external oscillator when hitting
off-idle.
And Beagle XM seems to have OSC_EN pin connected to allow shutting
down the oscillator looking at the schematics. The oscillator
output is cut off in off-idle and you can monitor it from R56 on
the bottom side of the board near the power jack. Note that for
beagle we need to also enable the UART wake-up event, the others
have that enabled in earlier patches.
OMAP37XX EVM (TMDSEVM3730) does not seem to have twl4030 clken
pin connected, so there is no point trying to enable shutting
down of the oscillator on it for the extra latency it adds.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Looks like quite a few omap3 boards have sharp ls037v7dw01 that's
configured as various panel dpi entries for whatever legacy reasons.
For device tree based support, let's just configure these properly for
panel ls037v7dw01 instead of panel dpi.
This patch creates a common file for panel ls037v7dw01, and makes
boards ldp and omap3-evm to use it.
The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen
controller for the omaps, so let's add a basic configuration for
the touchscreen also using the default values.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
I've tested the serial, MMC, smsc911x, wl12xx, and off-idle support
with the pinctrl patches, so it probably works better than the
board-*.c files ever did. Also the board-omap3evm.c file is broken
for the DSS, and has been for a while. Patches are welcome to fix
it in this .dts file, let's just drop the board-*.c file for this.
Note that off-idle currently requires doing request_irq() on the
wake-up pin from pinctrl-single IRQ domain until we can handle
that in some Linux generic way.
[tony@atomide.com: updated for make dtbs build fix]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
Looks like the main difference between the TMDSEVM3530 and
TMDSEVM3730 is just the omap processor:
http://www.ti.com/tool/tmdsevm3530
http://www.ti.com/tool/tmdsevm3730
So let's add a common file for the EVMs, and fix the description
for the omap3-evm.dst as that's clearly for the TMDSEVM3530
since it includes omap34xx.dtsi. It cannot support the TMDSEVM3730
properly, and we need a separate file for that in the following
patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
