| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
| |
|
|
|
|
|
|
|
|
| |
OPP table value is get from allwinner lichee linux-3.10 kernel driver
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220517013607.2252-3-qianfanguijin@163.com
|
| |
|
|
|
|
|
|
|
|
| |
The CPU of sun8i-r40 is powered by PMIC, let's add "cpu-supply" node.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220517013607.2252-2-qianfanguijin@163.com
|
| |
|
|
|
|
|
|
|
|
| |
Ethernet PHY on BananaPi M2 Ultra provides RX and TX delays. Fix
ethernet node to reflect that fact.
Fixes: c36fd5a48bd2 ("ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC ethernet controller")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201025081949.783443-1-jernej.skrabec@siol.net
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull ARM Devicetree updates from Olof Johansson:
"As usual, most of the changes are to devicetrees.
Besides smaller fixes, some refactorings and cleanups, some of the new
platforms and chips (or significant features) supported are below:
Broadcom boards:
- Cisco Meraki MR32 (BCM53016-based)
- BCM2711 (RPi4) display pipeline support
Actions Semi boards:
- Caninos Loucos Labrador SBC (S500-based)
- RoseapplePi SBC (S500-based)
Allwinner SoCs/boards:
- A100 SoC with Perf1 board
- Mali, DMA, Cetrus and IR support for R40 SoC
Amlogic boards:
- Libretch S905x CC V2 board
- Hardkernel ODROID-N2+ board
Aspeed boards/platforms:
- Wistron Mowgli (AST2500-based, Power9 OpenPower server)
- Facebook Wedge400 (AST2500-based, ToR switch)
Hisilicon SoC:
- SD5203 SoC
Nvidia boards:
- Tegra234 VDK, for pre-silicon Orin SoC
NXP i.MX boards:
- Librem 5 phone
- i.MX8MM DDR4 EVK
- Variscite VAR-SOM-MX8MN SoM
- Symphony board
- Tolino Shine 2 HD
- TQMa6 SoM
- Y Soft IOTA Orion
Rockchip boards:
- NanoPi R2S board
- A95X-Z2 board
- more Rock-Pi4 variants
STM32 boards:
- Odyssey SOM board (STM32MP157CAC-based)
- DH DRC02 board
Toshiba SoCs/boards:
- Visconti SoC and TPMV7708 board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (638 commits)
ARM: dts: nspire: Fix SP804 users
arm64: dts: lg: Fix SP804 users
arm64: dts: lg: Fix SP805 clocks
ARM: mstar: Fix up the fallout from moving the dts/dtsi files
ARM: mstar: Add mstar prefix to all of the dtsi/dts files
ARM: mstar: Add interrupt to pm_uart
ARM: mstar: Add interrupt controller to base dtsi
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
arm64: dts: ti: k3-j7200-main: Add USB controller
arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
ARM: dts: hisilicon: add SD5203 dts
ARM: dts: hisilicon: fix the system controller compatible nodes
arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
arm64: dts: zynqmp: Remove undocumented u-boot properties
arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
BananaPi M2 Ultra has IR receiver connected to IR0.
Enable it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200825171358.1286902-4-jernej.skrabec@siol.net
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
| |
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: da7ac948fa93 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200824193649.978197-1-jernej.skrabec@siol.net
|
| |
|
|
|
|
|
|
| |
Now that the regulators are tied to the GPIO bank, we can remove the
unneeded regulator-always-on in reg_aldo2
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
|
| |
The bananapi-m2-ultra has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs, tie them to the pio
node.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART3 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO1 and
DLDO2 regulator outputs from the PMIC provide overall power via VBAT and
I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides
the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin
PI12. This can be represented in multiple ways. This patch puts the
pinctrl property in the pin controller node. This is due to limitations
in Linux, where pinmux settings, even the same one, can not be shared
by multiple devices. Thus we cannot put it in both the WiFi and
Bluetooth device nodes. Putting it the CCU node is another option, but
Linux's CCU driver does not handle pinctrl. Also the pin controller is
guaranteed to be initialized after the CCU, when clocks are available.
And any other devices that use muxed pins are guaranteed to be
initialized after the pin controller. Thus having the CLK_OUT_A pinmux
reference be in the pin controller node is a good choice without having
to deal with implementation issues.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The design of the Bananapi M2 Ultra has both DLDO1 and DLDO2 regulators
provide power to the WiFi+BT module, which is based on the Broadcom
BCM43438 or BCM43430 chip. Each regulator output from the PMIC can supply
up to 200 mA. The datasheet of the chip suggests a maximum power draw of
up to 360 mA when transmitting, thus requiring two outputs from the PMIC
to handle the load. However the device tree only references one of them,
leaving the other unused and possibly turned off.
This patch marks both as always-on, since we don't have a proper binding
to specify two regulators as "bound together". The name and constraints
of DLDO2 are also added.
Fixes: da7ac948fa93 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2
Ultra")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
| |
This patch enable the AHCI controller.
Since this controller need two regulator, this patch add them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
| |
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
|
|
| |
R40 has 4 TCONs, but only 2 of them can receive some kind of output at
the same time. Let's disable them by default, so only those which are
really connected on board can be enabled in board dts file.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Current R40 is missing some graph connections between TCON TOP and
TCONs.
Add them.
Fixes: 05a43a262d03 ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
| |
Since HDMI can be considered as main output, most capable mixer is
connected to it (mixer0).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
|
| |
The Bananapi M2 Ultra has a Realtek RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
The device nodes dereference (&foo) usages should be sorted by the label
names, barring any parsing order issues such as the #include statement
for the PMIC's .dtsi file that must come after the PMIC.
Move the mmc and ohci blocks in front of the PMIC's regulator blocks.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
| |
|
|
|
|
|
|
|
|
| |
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Banana Pi M2 Ultra board features two USB host ports, connected to the
two USB host ports on the SoC.
Add support for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
On newer revisions of the Banana Pi M2 Ultra boards, the 5V power output
(used by HDMI, SATA and USB) is controller via a GPIO.
Add the regulator node for it.
Older revisions just have the 5V power output always on, and the GPIO is
reserved on these boards. So it won't affect the older revisions.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
|
The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
form factor and position of various connectors, leds and buttons is
similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
as the latest Banana Pi M64.
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 2 GB DDR3 DRAM
- 8 GB eMMC
- micro SD card slot
- DC power jack
- HDMI output
- MIPI DSI connector
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 chip, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- consumer IR receiver
- audio out headphone jack
- onboard microphone
- red, green, and blue LEDs
- debug UART pins
- Li-Po battery connector
- Raspberry Pi B+ compatible GPIO header
- power, reset, and boot control buttons
This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
