summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts (follow)
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: imx7: Unify temp-grade and speed-grade nodesFabio Estevam2020-01-092-8/+3
| | | | | | | | | | | | The following warning is seen when building with W=1: arch/arm/boot/dts/imx7s.dtsi:551.39-553.7: Warning (unique_unit_address): /soc/aips-bus@30000000/ocotp-ctrl@30350000/temp-grade@10: duplicate unit-address (also used in node /soc/aips-bus@30000000/ocotp-ctrl@30350000/speed-grade@10) Since temp-grade and speed-grade point to the same node, replace them by a single one to avoid the duplicate unit-address warning. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6: phycore-som: add pmic onkey deviceMarco Felsch2020-01-091-0/+4
| | | | | | | | Without the onkey device it isn't possible to power off the system using the X_PMIC_nONKEY signal which is routed to the SoM pin header. Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx51-babbage: Fix the DVI output descriptionFabio Estevam2019-12-231-15/+49
| | | | | | | | | | imx51-babbage has a TFP410 chip that receives 24-bit RGB parallel input and convert it to DVI. Fix the device tree description to reflect the real hardware. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6qdl-apalis: mux HDMI CEC pinStefan Agner2019-12-231-1/+1
| | | | | | | | Mux the HDMI CEC pin to make HDMI CEC working. With this change HDMI CEC seems to work fine on a Apalis iMX6 on Ixora using cec-ctl. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6sll: add PXP moduleAndreas Kemnade2019-12-231-0/+9
| | | | | | | | | | | | | While the EPDC is optional, both consumer and industrial editions have the PXP module, so adding it to the corresponding .dtsi Information taken from freescale kernel, compared with the reference manual and tested by a separate program. Since it does not depend on external wiring, the status = "disabled" is left out here. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: colibri-imx6ull: correct wrong pinmuxing and add commentsPhilippe Schenker2019-12-121-94/+94
| | | | | | | | | | | | | Some pinmuxings are obviously wrong, originating from a copy/paste error. This patch corrects that with the following strategy: - Set all reserved bits to zero - Leave drive strength and slew rate as is - Add sensible pull and hysteresis depending on the function of the pin - Not used pins are muxed to their reset-value defined by the SoC Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: vf610-zii-scu4-aib: Add node for switch watchdogAndrey Smirnov2019-12-121-0/+5
| | | | | | | | | | | | Add I2C child node for switch watchdog present on SCU4. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: vf610-zii-scu4-aib: Use generic names for DT nodesAndrey Smirnov2019-12-121-12/+12
| | | | | | | | | | | | | | | | The devicetree specification recommends using generic node names. Some ZII dts files already follow such recommendation, but some don't, so use generic node names for consistency among the ZII dts files. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Fabio Estevam <festevam@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: vf610-zii-dev-rev-b: Drop redundant I2C propertiesAndrey Smirnov2019-12-121-10/+0
| | | | | | | | | | | | | | ZII VF610 Board Rev. B is supposed to have exactly the same I2C config as Rev. C, including I2C bus recovery settings. Drop redundant I2C properties that are already specified in vf610-zii-dev.dtsi Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: phycore-imx6: set buck regulator modes explicitlyChristoph Fritz2019-12-121-0/+5
| | | | | | | | | This patch sets initial buck regulator modes explicitly to a state this hardware needs. So a wrong initial mode set by bootloader or pmic itself does not interfere anymore. Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6: rdu2: Limit USBH1 to Full SpeedAndrey Smirnov2019-12-121-0/+1
| | | | | | | | | | | | | | | | | Cabling used to connect devices to USBH1 on RDU2 does not meet USB spec cable quality and cable length requirements to operate at High Speed, so limit the port to Full Speed only. Reported-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3Andrey Smirnov2019-12-121-4/+2
| | | | | | | | | | | | | | | | | RDU2 production units come with resistor connecting WP pin to correpsonding GPIO DNPed for both SD card slots. Drop any WP related configuration and mark both slots with "disable-wp". Reported-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6: rdu2: Add node for UCS1002 USB charger chipAndrey Smirnov2019-12-121-18/+59
| | | | | | | | | | | | | | | | Add node for UCS1002 USB charger chip connected to front panel USB and replace "regulator-fixed" previously used to control VBUS. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx7s: Add power domain for imx7d HSICPeter Chen2019-12-121-0/+7
| | | | | | | | | Otherwise, the system will hang if USB driver try to access portsc register. Cc: André Draszik <git@andred.net> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx7ulp-com: Add initial support for i.MX7UP COM boardFabio Estevam2019-12-112-0/+80
| | | | | | | | | | | | The Embedded Artists COM board is based on NXP i.MX7ULP. It has a BD70528 PMIC from Rohm with discrete DCDC powering option and improved current observability (compared to the existing NXP i.MX7ULP EVK). Add the initial support for the board. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYsVladimir Oltean2019-12-091-0/+4
| | | | | | | | | | | | | | | | On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and eth1 have interrupt lines connected to the shared IRQ2_B LS1021A pin. Switching to interrupts offloads the PHY library from the task of polling the MDIO status and AN registers (1, 4, 5) every second. Unfortunately, the BCM5464R quad PHY connected to the switch does not appear to have an interrupt line routed to the SoC. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: ls1021a: add node describing external interrupt linesRasmus Villemoes2019-12-091-0/+19
| | | | | | | | This adds a node describing the six external interrupt lines IRQ0-IRQ5 with configurable polarity. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx25: describe maximum speed of internal usbhost port1 phyMichael Grzeschik2019-12-091-0/+1
| | | | | | | | | The internal usbphy of usbhost port1 is only full-speed capable. We set this limitation in the dtsi. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx25: consolidate properties of usbhost1 in dtsi fileMichael Grzeschik2019-12-093-4/+2
| | | | | | | | | | | The usb port represented by &usbhost1 uses an USB phy internal to the SoC. We add the phy_type to the base dtsi so the board dts only have to overwrite it if they use a different configuration. While at it we also pin the usbhost port to host mode. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: e60k02: Pass the memory unit addressFabio Estevam2019-12-091-1/+2
| | | | | | | | | | | | | | | | The following build warning is seen with W=1: DTC arch/arm/boot/dts/imx6sll-kobo-clarahd.dtb arch/arm/boot/dts/e60k02.dtsi:51.9-53.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name Pass the memory unit address to fix the problem. While at it, also pass 'device_type = "memory"', which is recommended for memory nodes. Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: add devicetree entry for Tolino Shine 3Andreas Kemnade2019-12-092-0/+327
| | | | | | | | | | The device is almost identical to the Kobo Clara HD. The only spotted difference is the SoC. It contains an imx6sl instead of an imx6sll. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx7d-sdb-reva: Add revision in board compatible stringAnson Huang2019-12-091-0/+3
| | | | | | | | i.MX7D SDB Rev-A board should use its own board compatible string instead of default i.MX7D SDB board. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6sx-sdb-reva: Add revision in board compatible stringAnson Huang2019-12-091-0/+1
| | | | | | | | i.MX6SX SDB Rev-A board should use its own board compatible string instead of default i.MX6SX SDB board. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: imx6q-logicpd: Enable ili2117a TouchscreenAdam Ford2019-12-091-0/+10
| | | | | | | | | | The LCD used with the imx6q-logicpd board has an integrated ili2117a touch controller connected to i2c1. This patch adds the node to enable this feature. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* Merge tag 'arm-soc/for-5.5/devicetree-part2' of ↵Olof Johansson2019-12-062-0/+63
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://github.com/Broadcom/stblinux into arm/fixes This pull request contains the second batch of changes for Broadcom ARM-based SoCs, please pull the following: - Nicolas declares a CMA area within the first 1GB of DRAM in order for it to be guaranteed to reside there, otherwise ARM64's memory initialization will pick up a CMA area within ZONE_DMA32 - Stefan adds the Device Tree node for the built-in Ethernet controller (GENET) on the Raspberry Pi 4 model B board * tag 'arm-soc/for-5.5/devicetree-part2' of https://github.com/Broadcom/stblinux: ARM: dts: bcm2711-rpi-4: Enable GENET support ARM: dts: bcm2711: force CMA into first GB of memory Link: https://lore.kernel.org/r/20191118182931.11884-1-f.fainelli@gmail.com Signed-off-by: Olof Johansson <olof@lixom.net>
| * ARM: dts: bcm2711-rpi-4: Enable GENET supportStefan Wahren2019-11-142-0/+43
| | | | | | | | | | | | | | | | | | | | | | This enables the Gigabit Ethernet support on the Raspberry Pi 4. The defined PHY mode is equivalent to the default register settings in the downstream tree. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
| * ARM: dts: bcm2711: force CMA into first GB of memoryNicolas Saenz Julienne2019-11-141-0/+20
| | | | | | | | | | | | | | | | | | | | arm64 places the CMA in ZONE_DMA32, which is not good enough for the Raspberry Pi 4 since it contains peripherals that can only address the first GB of memory. Explicitly place the CMA into that area. Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Acked-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* | Merge tag 'omap-for-v5.5/dt-fixes-merge-window-signed' of ↵Olof Johansson2019-12-068-10/+20
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Device tree fixes for omap variants for for v5.5 merge window This series of changes contains fixes for few SoC and board specific issues that would be good to have merged for v5.5-rc1: - Fix incorrect MMC card detection polarity for omap3-tao3530 - Fix wrong am57xx-beagle-x15 pinmux named states for eMMC - Fix dra7 cpsw mdio clock that causes wrong speed - Fix vcsi for droid4 so it won't get turned off after init - Fix rev and sysconfig register offsets for omap4 sgx so it can idle Then there are also two minor late changes to logicpd-torpedo-baseboard to configure 1-wire HDQ for battery stats, and remove out of date workaround comments no longer needed. * tag 'omap-for-v5.5/dt-fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: Fix sgx sysconfig register for omap4 ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangs ARM: dts: dra7: fix cpsw mdio fck clock ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3v ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity ARM: dts: logicpd-torpedo: Remove unnecessary notes/comments ARM: dts: logicpd-torpedo-baseboard: Enable HDQ Link: https://lore.kernel.org/r/pull-1574870758-237468@atomide.com Signed-off-by: Olof Johansson <olof@lixom.net>
| * | ARM: dts: Fix sgx sysconfig register for omap4Tony Lindgren2019-11-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Looks like we've had the sgx sysconfig register and revision register always wrong for omap4, including the old platform data. Let's fix the offsets to what the TRM says. Otherwise the sgx module may never idle depending on the state of the real sysconfig register. Fixes: d23a163ebe5a ("ARM: dts: Add nodes for missing omap4 interconnect target modules") Cc: H. Nikolaus Schaller <hns@goldelico.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangsTony Lindgren2019-11-211-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In addition to using vcsi regulator for the display, looks like droid4 is using vcsi regulator to trigger off mode internally with the PMIC firmware when the SoC enters deeper idle states. This is configured in the Motorola Mapphone Linux kernel sources as "zerov_regulator". As we currently don't support off mode during idle for omap4, we must prevent vcsi from being disabled when the display is blanked to prevent the PMIC change to off mode. Otherwise the device will hang on entering idle when the display is blanked. Before commit 089b3f61ecfc ("regulator: core: Let boot-on regulators be powered off"), the boot-on regulators never got disabled like they should and vcsi did not get turned off on idle. Let's fix the issue by setting vcsi to always-on for now. Later on we may want to claim the vcsi regulator also in the PM code if needed. Fixes: 089b3f61ecfc ("regulator: core: Let boot-on regulators be powered off") Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | ARM: dts: dra7: fix cpsw mdio fck clockGrygorii Strashko2019-11-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DRA7 CPSW MDIO functional clock (gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 0) is specified incorrectly, which is caused incorrect MDIO bus clock configuration MDCLK. The correct CPSW MDIO functional clock is gmac_main_clk (125MHz), which is the same as CPSW fck. Hence fix it. Fixes: 1faa415c9c6e ("ARM: dts: Add fck for cpsw mdio for omap variants") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3vFaiz Abbas2019-11-202-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | am57xx-beagle-x15 revb1 and revc have 3.3V connected to the eMMC I/O lines. Update the pinmux name to reflect this. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarityJarkko Nikula2019-11-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MMC card detection GPIO polarity is active low on TAO3530, like in many other similar boards. Now the card is not detected and it is unable to mount rootfs from an SD card. Fix this by using the correct polarity. This incorrect polarity was defined already in the commit 30d95c6d7092 ("ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi") in v3.18 kernel and later changed to use defined GPIO constants in v4.4 kernel by the commit 3a637e008e54 ("ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards"). While the latter commit did not introduce the issue I'm marking it with Fixes tag due the v4.4 kernels still being maintained. Fixes: 3a637e008e54 ("ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards") Cc: linux-stable <stable@vger.kernel.org> # 4.4+ Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | ARM: dts: logicpd-torpedo: Remove unnecessary notes/commentsAdam Ford2019-11-142-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There used to be a bug in the video driver that caused the timings for the LCD to calculate in a way on the DM3730 which made it hang. The work around for this bug was to set CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 in the kernel. This work around is no longer needed as the video drivers have been corrected. This patch removes the legacy note. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | ARM: dts: logicpd-torpedo-baseboard: Enable HDQAdam Ford2019-11-141-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The baseboard of the Logic PD Torpedo development kit has a socket for a rechargable battery. The battery is monitored by a charger which can communicate of the the 1-wire HDQ pin. This patch enables the pinmux for the HDQ pin. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | | Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds2019-12-05254-5669/+20143
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM Device-tree updates from Olof Johansson: "As always, the bulk of updates. Some of the news this cycle: New SoC descriptions: - Broadcom BCM2711 - Amlogic Meson A1 and G12 - Freescale S32V234 - Marvell Armada AP807/AP807-quad and CP115 - Realtek RTD1293 and RTD1296 - Rockchip RK3308 New boards and platforms: - Allwinner: NanoPi Duo2 - Amlogic: Ugoos am6 - Atmel at91: Overkiz Kizbox2/4 - Broadcom: RPi4, Luxul XWC-2000 - Marvell: New Espressobin flavor - NXP: i.MX8MN LPDDR4 EVK, i.MX8QXP Colibri, S32V234 EVB, Netronix E60K02 and Kobo Clara HD, Kontron N6311 and N6411, OPOS6UL and OPOS6ULDev - Renesas: Salvator-XS - Rockchip: Beelink A1 (rk3308), rk3308 eval boards, rk3399-roc-pc" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (653 commits) ARM: dts: logicpd-torpedo: Disable USB Host arm: dts: mt6323: add keys, power-controller, rtc and codec arm64: dts: mt8183: add systimer0 device node dt-bindings: mediatek: update bindings for MT8183 systimer arm64: dts: rockchip: fix sdmmc detection on boot on rk3328-roc-cc arm64: dts: rockchip: Split rk3399-roc-pc for with and without mezzanine board. arm64: dts: rockchip: Add Beelink A1 dt-bindings: ARM: rockchip: Add Beelink A1 arm64: dts: rockchip: Add RK3328 audio pipelines arm64: dts: ti: k3-j721e-common-proc-board: Add USB ports arm64: dts: ti: k3-j721e-main: add USB controller nodes ARM: dts: aspeed-g6: Add timer description ARM: dts: aspeed: ast2600evb: Enable i2c buses ARM: dts: at91: add a dts and dtsi file for kizbox2 based boards dt-bindings: arm: at91: Document Kizbox2-2 board binding arm64: dts: meson-gx: fix i2c compatible arm64: dts: meson-gx: cec node should be disabled by default arm64: dts: meson-g12b-odroid-n2: add missing amlogic, s922x compatible arm64: dts: meson-gxm: fix gpu irq order arm64: dts: meson-g12a: fix gpu irq order ...
| * | | Merge tag 'omap-for-v5.5/dt-late-signed' of ↵Olof Johansson2019-11-135-1/+42
| |\| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt Few late dts changes for omaps for v5.5 merge window Let's configure omap3 rng as we can now easily do it with a dts change only by tagging it with status = "disabled" for n900 where it's not accessible. This improves the boot-up time with distros quite a bit with proper entropy source around. There's also another minor update for logicpd-torpedo that does not have USB host pins wired. * tag 'omap-for-v5.5/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: logicpd-torpedo: Disable USB Host ARM: dts: Configure omap3 rng Link: https://lore.kernel.org/r/pull-1573579927-542764@atomide.com Signed-off-by: Olof Johansson <olof@lixom.net>
| | * | ARM: dts: logicpd-torpedo: Disable USB HostAdam Ford2019-11-111-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While the OMAP3 family has a USB Host controller, the Torpedo does not route the host pins off the board rendering it useless. This patch removes the host references. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | * | Merge branch 'rng' into omap-for-v5.5/dtTony Lindgren2019-10-304-1/+37
| | |\ \
| | | * | ARM: dts: Configure omap3 rngTony Lindgren2019-10-304-1/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Looks like omap3 RNG is similar to the omap2 rng, let's get it working by configring the dts node for it. We must also add rng_ick to core_l4_clkdm as noted by Adam Ford. And please note that the RNG is likely disabled on HS devices. At least n900 does not have it accessible, and instead omap3-rom-rng driver must be used. So let's tag RNG as disabled on n900 as noted by Pali Rohár <pali.rohar@gmail.com>. On am3517 at least the clocks need to be configured to get it working as noted by Adam Ford, so let's tag it disabled for now. Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Adam Ford <aford173@gmail.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Sebastian Reichel <sre@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | | | Merge tag 'v5.4-next-dts' of ↵Olof Johansson2019-11-111-0/+27
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt mt6323 pmic: add nodes for RTC, keys, codec and power-controller * tag 'v5.4-next-dts' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: arm: dts: mt6323: add keys, power-controller, rtc and codec Link: https://lore.kernel.org/r/82f16220-d0e1-6e32-088e-c889ef6bdff3@gmail.com Signed-off-by: Olof Johansson <olof@lixom.net>
| | * | | | arm: dts: mt6323: add keys, power-controller, rtc and codecJosef Friedl2019-11-101-0/+27
| | | |/ / | | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | support poweroff and power-related keys on bpi-r2 Suggested-by: Frank Wunderlich <frank-w@public-files.de> Signed-off-by: Josef Friedl <josef.friedl@speed.at> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
| * | | | Merge tag 'v5.5-rockchip-dts32-2' of ↵Olof Johansson2019-11-112-0/+8
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt HDMI-audio support for Veyron devices. * tag 'v5.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: Add HDMI audio support to rk3288-veyron-mickey ARM: dts: rockchip: Add HDMI support to rk3288-veyron-analog-audio Link: https://lore.kernel.org/r/1926436.N9mSsAMzn9@phil Signed-off-by: Olof Johansson <olof@lixom.net>
| | * | | | ARM: dts: rockchip: Add HDMI audio support to rk3288-veyron-mickeyCheng-Yi Chiang2019-10-311-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add HDMI audio support to veyron-mickey. The sound card should expose one audio device for HDMI. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Link: https://lore.kernel.org/r/20191028071930.145899-7-cychiang@chromium.org Signed-off-by: Heiko Stuebner <heiko@sntech.de>
| | * | | | ARM: dts: rockchip: Add HDMI support to rk3288-veyron-analog-audioCheng-Yi Chiang2019-10-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All boards using rk3288-veyron-analog-audio.dtsi have HDMI audio. Specify the support of HDMI audio on machine driver using rockchip,hdmi-codec property so machine driver creates HDMI audio device. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Link: https://lore.kernel.org/r/20191028071930.145899-6-cychiang@chromium.org Signed-off-by: Heiko Stuebner <heiko@sntech.de>
| * | | | | Merge tag 'at91-5.5-dt' of ↵Olof Johansson2019-11-0810-246/+1016
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt AT91 DT for 5.5 - New Overkiz Kizbox3 board - Rework of the other Kizbox device trees - New filters for i2c on sama5d4 and sama5d2 * tag 'at91-5.5-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: ARM: dts: at91: add a dts and dtsi file for kizbox2 based boards dt-bindings: arm: at91: Document Kizbox2-2 board binding ARM: dts: at91: sama5d4_xplained: add digital filter for i2c ARM: dts: at91: sama5d2_xplained: add analog and digital filter for i2c ARM: dts: at91: add Overkiz KIZBOX3 board dt-bindings: arm: at91: Document Kizbox3 HS board binding dt-bindings: Add vendor prefix for Overkiz SAS ARM: dts: at91: sama5d2: add an rtc label for derived boards ARM: dts: at91: sama5d27_som1_ek: add mmc capabilities for SDMMC0 Link: https://lore.kernel.org/r/20191108070938.GA215379@piout.net Signed-off-by: Olof Johansson <olof@lixom.net>
| | * | | | | ARM: dts: at91: add a dts and dtsi file for kizbox2 based boardsKamel Bouhara2019-11-074-245/+285
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are several boards available depending on the PCB (3 antennas support and several revison). Add a dtsi file to share common binding between all kizbox2 boards. This patch also add support for the kizbox2-2 variant. Signed-off-by: Kévin RAYMOND <k.raymond@overkiz.com> Signed-off-by: Mickael GARDET <m.gardet@overkiz.com> Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> Link: https://lore.kernel.org/r/20191105212234.22999-2-kamel.bouhara@bootlin.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
| | * | | | | ARM: dts: at91: sama5d4_xplained: add digital filter for i2cEugen Hristev2019-10-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add property for digital filter for i2c0 node sama5d4_xplained Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lore.kernel.org/r/1568189911-31641-10-git-send-email-eugen.hristev@microchip.com Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
| | * | | | | ARM: dts: at91: sama5d2_xplained: add analog and digital filter for i2cEugen Hristev2019-10-251-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add property for analog and digital filter for i2c1 and i2c2 nodes for sama5d2_xplained Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lore.kernel.org/r/1568189911-31641-9-git-send-email-eugen.hristev@microchip.com Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
| | * | | | | ARM: dts: at91: add Overkiz KIZBOX3 boardKamel Bouhara2019-10-163-0/+722
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a common DT include file for the Kizbox3 boards. Add the devicetree for the Kizbox3 HS board. Signed-off-by: Kévin RAYMOND <k.raymond@overkiz.com> Signed-off-by: Mickael GARDET <m.gardet@overkiz.com> Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> Link: https://lore.kernel.org/r/20191011125022.16329-4-kamel.bouhara@bootlin.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-02-03 02:57:27 +0100