summaryrefslogtreecommitdiffstats
path: root/arch/mips/boot/dts (follow)
Commit message (Collapse)AuthorAgeFilesLines
* MIPS: DTS: CI20: fix how ddc power is enabledH. Nikolaus Schaller2022-02-091-13/+2
| | | | | | | | | | | | | | Originally we proposed a new hdmi-5v-supply regulator reference for CI20 device tree but that was superseded by a better idea to use the already defined "ddc-en-gpios" property of the "hdmi-connector". Since "MIPS: DTS: CI20: Add DT nodes for HDMI setup" has already been applied to v5.17-rc1, we add this on top. Fixes: ae1b8d2c2de9 ("MIPS: DTS: CI20: Add DT nodes for HDMI setup") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: bmips: Add support PCIe controller device nodesJim Quinlan2022-01-114-0/+78
| | | | | | | | | | For Broadcom STB PCIe HW. The 7425 and 7435 are MIPs-based SOCs. Not much difference between the two for the DT properties except that they have slightly different PCIe interrupt assignments. Signed-off-by: Jim Quinlan <jim2101024@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: Loongson64: DTS: Add pm block node for Loongson-2K1000Qing Zhang2022-01-021-0/+5
| | | | | | | The module is now supported, enable it. Signed-off-by: Qing Zhang <zhangqing@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: DTS: Ingenic: adjust register size to available registersH. Nikolaus Schaller2021-12-093-3/+3
| | | | | | | | | | | | | After getting the regmap size from the device tree we should reduce the ranges to the really available registers. This allows to read only existing registers from the debug fs and makes the regmap check out-of-bounds access. For the jz4780 we have done this already. Suggested-for: Paul Cercueil <paul@crapouillou.net> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: DTS: CI20: Add DT nodes for HDMI setupPaul Boddie2021-12-091-2/+70
| | | | | | | | | | | | | We need to hook up * HDMI connector * HDMI power regulator * JZ4780_CLK_HDMI @ 27 MHz * DDC pinmux * HDMI and LCDC endpoint connections Signed-off-by: Paul Boddie <paul@boddie.org.uk> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: DTS: jz4780: Account for Synopsys HDMI driver and LCD controllersPaul Boddie2021-12-091-0/+40
| | | | | | | | | | | | A specialisation of the generic Synopsys HDMI driver is employed for JZ4780 HDMI support. This requires a new driver, plus device tree and configuration modifications. Here we add jz4780 device tree setup. Signed-off-by: Paul Boddie <paul@boddie.org.uk> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* dt-bindings: Rename Ingenic CGU headers to ingenic,*.hPaul Cercueil2021-11-126-6/+6
| | | | | | | | | | | Tidy up a bit the tree, by prefixing all include/dt-bindings/clock/ files related to Ingenic SoCs with 'ingenic,'. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20211016133322.40771-1-paul@crapouillou.net
* Merge tag 'mips_5.16' of ↵Linus Torvalds2021-11-057-580/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS updates from Thomas Bogendoerfer: - added printing of CPU options for /proc/cpuinfo - removed support for Netlogic SOCs - fixes and cleanup * tag 'mips_5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MIPS: Cobalt: Explain GT64111 early PCI fixup mips: fix HUGETLB function without THP enabled mips: cm: Convert to bitfield API to fix out-of-bounds access MIPS: Remove NETLOGIC support MIPS: kernel: proc: add CPU option reporting MIPS: kernel: proc: use seq_puts instead of seq_printf MIPS: kernel: proc: fix trivial style errors MIPS: Fix assembly error from MIPSr2 code used within MIPS_ISA_ARCH_LEVEL MIPS: octeon: Remove unused functions MIPS: Loongson64: Add of_node_put() before break bcm47xx: Replace printk(KERN_ALERT ... pci_devname(dev)) with pci_alert() bcm47xx: Get rid of redundant 'else' MIPS: sni: Fix the build MIPS: Avoid macro redefinitions MIPS: loongson64: Fix no screen display during boot-up MIPS: loongson64: make CPU_LOONGSON64 depends on MIPS_FP_SUPPORT
| * MIPS: Remove NETLOGIC supportThomas Bogendoerfer2021-10-247-580/+0
| | | | | | | | | | | | No (active) developer owns this hardware, so let's remove Linux support. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* | MIPS: JZ4780: CI20: DTS: add SPI controller configArtur Rojek2021-09-132-15/+38
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add nodes for the two SPI controllers found in MIPS Creator CI20. 2. Reparent SPI clock source to effectively use MPLL and set its clock rate to 54MHz. NOTE: To use the SPI controllers, `pinctrl-0` property must be set in order to configure the used pins. As SPI functionality is multiplexed on multiple pin groups, this choice is left to the user. An example configuration: ``` &spi0 { pinctrl-0 = <&pins_spi0>; } pins_spi0: spi0 { function = "ssi0"; groups = "ssi0-dt-e", "ssi0-dr-e", "ssi0-clk-e", "ssi0-ce0-e", "ssi0-ce1-e"; bias-disable; }; ``` Consult the CI20 pinout description for more details. Signed-off-by: Artur Rojek <contact@artur-rojek.eu> Link: https://lore.kernel.org/r/20210830230139.21476-4-contact@artur-rojek.eu Signed-off-by: Mark Brown <broonie@kernel.org>
* MIPS: mscc: ocelot: mark the phy-mode for internal PHY portsVladimir Oltean2021-08-212-0/+8
| | | | | | | | | | | | | The ocelot driver was converted to phylink, and that expects a valid phy_interface_t. Without a phy-mode, of_get_phy_mode returns PHY_INTERFACE_MODE_NA, which is not ideal because phylink rejects that. The ocelot driver was patched to treat PHY_INTERFACE_MODE_NA as PHY_INTERFACE_MODE_INTERNAL to work with the broken DT blobs, but we should fix the device trees and specify the phy-mode too. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: mscc: ocelot: disable all switch ports by defaultVladimir Oltean2021-08-213-0/+23
| | | | | | | | | | | | | | | | | | | The ocelot switch driver used to ignore ports which do not have a phy-handle property and not probe those, but this is not quite ok since it is valid to not have a phy-handle property if there is a fixed-link. It seems that checking for a phy-handle was a proxy for the proper check which is for the status, but that doesn't make a lot of sense, since the ocelot driver already iterates using for_each_available_child_of_node which skips the disabled ports, so I have no idea. Anyway, a widespread pattern in device trees is for a SoC dtsi to disable by default all hardware, and let board dts files enable what is used. So let's do that and enable only the ports with a phy-handle in the pcb120 and pcb123 device tree files. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: Retire MACH_PISTACHIOJiaxun Yang2021-08-122-4/+0
| | | | | | | Now it can be replaced by generic kernel. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: DTS: Pistachio add missing cpc and cdmmJiaxun Yang2021-08-121-0/+10
| | | | | | | | | | | | | | CPC and CDMM addresses are adjustable and we should tell kernel how to place them in devicetree. Note that MACH_PISTACHIO code hardcoded CDMM base to 0x1bdd0000, however it will collide with GIC address range. As we don't have any CDMM device on this platform it won't be a problem. I found another spare range, 0x1bdf0000~0x1be00000 to place CDMM instead. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: generic: Allow generating FIT image for Marduk boardJiaxun Yang2021-08-122-0/+3
| | | | | | | | | Marduk is based on IMG pistachio SoC. The platform is using MIPS UHI booting protocol and does have a proper devicetree implement, thus it could be a part of generic kernel. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* Merge tag 'mips_5.14' of ↵Linus Torvalds2021-07-0216-39/+182
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS updates from Thomas Bogendoerfer: - add support for OpeneEmbed SOM9331 board - Ingenic fixes/improvments - other fixes and cleanups * tag 'mips_5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (39 commits) MIPS: Fix PKMAP with 32-bit MIPS huge page support MIPS: CI20: Add second percpu timer for SMP. MIPS: CI20: Reduce clocksource to 750 kHz. MIPS: Ingenic: Add MAC syscon nodes for Ingenic SoCs. dt-bindings: clock: Add documentation for MAC PHY control bindings. MIPS: X1830: Respect cell count of common properties. MIPS: set mips32r5 for virt extensions MIPS: loongsoon64: Reserve memory below starting pfn to prevent Oops MIPS: MT extensions are not available on MIPS32r1 mips/kvm: Use BUG_ON instead of if condition followed by BUG MIPS: OCTEON: octeon-usb: Use devm_platform_get_and_ioremap_resource() MIPS: add PMD table accounting into MIPS'pmd_alloc_one MIPS: Loongson64: fix spelling of SPDX tag MIPS: ingenic: rs90: Add dedicated VRAM memory region MIPS: ingenic: gcw0: Set codec to cap-less mode for FM radio MIPS: ingenic: jz4780: Fix I2C nodes to match DT doc MIPS: ingenic: Select CPU_SUPPORTS_CPUFREQ && MIPS_EXTERNAL_TIMER MIPS: Kconfig: ingenic: Ensure MACH_INGENIC_GENERIC selects all SoCs MIPS: cpu-probe: Fix FPU detection on Ingenic JZ4760(B) MIPS: boot: Support specifying UART port on Ingenic SoCs ...
| * MIPS: CI20: Add second percpu timer for SMP.周琰杰 (Zhou Yanjie)2021-06-301-10/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | 1.Add a new TCU channel as the percpu timer of core1, this is to prepare for the subsequent SMP support. The newly added channel will not adversely affect the current single-core state. 2.Adjust the position of TCU node to make it consistent with the order in jz4780.dtsi file. Tested-by: Nikolaus Schaller <hns@goldelico.com> # on CI20 Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: CI20: Reduce clocksource to 750 kHz.周琰杰 (Zhou Yanjie)2021-06-301-2/+2
| | | | | | | | | | | | | | | | | | | | | | The original clock (3 MHz) is too fast for the clocksource, there will be a chance that the system may get stuck. Reported-by: Nikolaus Schaller <hns@goldelico.com> Tested-by: Nikolaus Schaller <hns@goldelico.com> # on CI20 Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: Ingenic: Add MAC syscon nodes for Ingenic SoCs.周琰杰 (Zhou Yanjie)2021-06-302-0/+14
| | | | | | | | | | | | | | | | Add MAC syscon nodes for X1000 SoC and X1830 SoC from Ingenic. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: X1830: Respect cell count of common properties.周琰杰 (Zhou Yanjie)2021-06-301-5/+4
| | | | | | | | | | | | | | | | | | | | If N fields of X cells should be provided, then that's what the devicetree should represent, instead of having one single field of (N * X) cells. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: Loongson64: fix spelling of SPDX tagTom Rix2021-06-211-1/+1
| | | | | | | | | | | | | | | | checkpatch looks for SPDX-License-Identifier. So change the '_' to '-' Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: ingenic: rs90: Add dedicated VRAM memory regionPaul Cercueil2021-06-011-0/+14
| | | | | | | | | | | | | | | | | | Add a 1 MiB memory area dedicated to the video driver. This area will be managed by Linux' CMA, so that the ingenic-drm driver can be sure to always be able to allocate contiguous buffers. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: ingenic: gcw0: Set codec to cap-less mode for FM radioPaul Cercueil2021-06-011-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | When using the FM radio, we must not have capacitors on the headphones line, since it is used as the antenna. The "FM Radio" widget is removed so that the cap-less mode can be enabled dynamically through DAPM when the line input is used. This widget was useless anyway. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: ingenic: jz4780: Fix I2C nodes to match DT docPaul Cercueil2021-06-011-5/+5
| | | | | | | | | | | | | | | | | | The "ingenic,jz4780-i2c" should have "ingenic,jz4770-i2c" as a fallback compatible, as per the Device Tree documentation found in Documentation/devicetree/bindings/i2c/ingenic,i2c.yaml. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * mips: dts: loongson: fix DTC unit name warningszhaoxiao2021-05-271-1/+1
| | | | | | | | | | | | | | | | | | Fixes the following W=1 kernel build warning(s): arch/mips/boot/dts/loongson/rs780e-pch.dtsi:24.7-41.5: Warning (unit_address_vs_reg): /bus@10000000/isa: node has a reg or ranges property, but no unit name arch/mips/boot/dts/loongson/rs780e-pch.dtsi:24.7-41.5: Warning (simple_bus_reg): /bus@10000000/isa: simple-bus unit address format error, expected "18000000" Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * mips: dts: loongson: fix DTC unit name warningszhaoxiao2021-05-271-1/+1
| | | | | | | | | | | | | | | | | | Fixes the following W=1 kernel build warning(s): arch/mips/boot/dts/loongson/ls7a-pch.dtsi:410.7-415.5: Warning (unit_address_vs_reg): /bus@10000000/isa: node has a reg or ranges property, but no unit name arch/mips/boot/dts/loongson/ls7a-pch.dtsi:410.7-415.5: Warning (simple_bus_reg): /bus@10000000/isa: simple-bus unit address format error, expected "18000000" Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * mips: dts: loongson: fix DTC unit name warningszhaoxiao2021-05-271-1/+1
| | | | | | | | | | | | | | | | | | Fixes the following W=1 kernel build warning(s): arch/mips/boot/dts/loongson/loongson64v_4core_virtio.dts:91.7-96.5: Warning (unit_address_vs_reg): /bus@10000000/isa: node has a reg or ranges property, but no unit name arch/mips/boot/dts/loongson/loongson64v_4core_virtio.dts:91.7-96.5: Warning (simple_bus_reg): /bus@10000000/isa: simple-bus unit address format error, expected "18000000" Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * mips: dts: loongson: fix DTC unit name warningszhaoxiao2021-05-271-2/+2
| | | | | | | | | | | | | | | | | | | | Fixes the following W=1 kernel build warning(s): arch/mips/boot/dts/loongson/loongson64g-package.dtsi:42.30-49.5: Warning (simple_bus_reg): /bus@1fe00000/serial@1fe001e0: simple-bus unit address format error, expected "1fe00100" arch/mips/boot/dts/loongson/loongson64g-package.dtsi:51.30-59.5: Warning (simple_bus_reg): /bus@1fe00000/serial@1fe001e8: simple-bus unit address format error, expected "1fe00110" Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com> Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * mips: dts: loongson: fix DTC unit name warningszhaoxiao2021-05-271-1/+1
| | | | | | | | | | | | | | | | Fixes the following W=1 kernel build warning(s): arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi:26.9-32.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: ath79: ar9331: add pause property for the MAC <> switch linkOleksij Rempel2021-05-271-0/+2
| | | | | | | | | | | | | | | | Both, MAC and switch support flow control, so add pause property for the MAC <> switch link. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: ath79: ar9331: Add OpeneEmbed SOM9331 BoardOleksij Rempel2021-05-272-0/+111
| | | | | | | | | | | | | | | | Add SOM9331 based Board. It has 3 LAN ports, usb to uart controller and USB type A port. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS: SEAD3: Correct Ethernet node nameGeert Uytterhoeven2021-05-271-1/+1
| | | | | | | | | | | | | | | | | | | | make dtbs_check: eth@1f010000: $nodename:0: 'eth@1f010000' does not match '^ethernet(@.*)?$' Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
| * MIPS:DTS:Correct device id of pcie for Loongnon-2KXiaochuan Mao2021-05-111-8/+8
| | | | | | | | | | | | | | | | | | | | | | from Loongson-2K user manual know that Loongson-2K have two pcie controller pcie0 and pcie1, pcie0 have four port named port0~port3 and pcie1 have 2 port named port0~port1. the device id of port0 is 7a19 in each pcie controller and others are 7a09. Signed-off-by: Xiaochuan Mao <maoxiaochuan@loongson.cn> Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* | MIPS: Loongson64: DTS: Add GMAC support for LS7A PCHQing Zhang2021-06-181-2/+4
| | | | | | | | | | | | | | The GMAC module is now supported, enable it. Signed-off-by: Qing Zhang <zhangqing@loongson.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
* | MIPS: Loongson64: Add GMAC support for Loongson-2K1000Qing Zhang2021-06-181-0/+46
|/ | | | | | | The GMAC module is now supported, enable it. Signed-off-by: Qing Zhang <zhangqing@loongson.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
* MIPS:DTS:Correct the license for Loongson-2Kxiaochuan mao2021-04-231-1/+1
| | | | | | | make license from GPL3.0 to GPL2.0 Signed-off-by: xiaochuan mao <maoxiaochuan@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS:DTS:Fix label name and interrupt number of ohci for Loongson-2Kxiaochuan mao2021-04-231-2/+2
| | | | | | | | | | | | from Loongson-2K1000 user manual know that under pci bus the device num is 4, function number is 2 and register is 0x2200 is ohci. the ohci interrupt number is 51. because Loongson-2K1000 has 64 interrupt sources, 0-31 correspond to the device tree liointc0 device node, and the other correspond to liointc1 node. so it should be number 19 correspon to liointc1. Signed-off-by: xiaochuan mao <maoxiaochuan@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm63268: populate device tree nodesÁlvaro Fernández Rojas2021-04-061-14/+116
| | | | | | | | | | | | | | | - Rename periph_clk to periph_osc. - Rename clkctl to periph_clk. - Move syscon-reboot to subnode. - Add hsspi-osc clock. - Add watchdog. - Add HS SPI controller - Add NAND controller. - Add USBH PHY. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6368: populate device tree nodesÁlvaro Fernández Rojas2021-04-061-11/+116
| | | | | | | | | | | | | | | | - Rename periph_clk to periph_osc. - Rename clkctl to periph_clk. - Move syscon-reboot to subnode. - Add watchdog controller. - Add SPI controller. - Add NAND controller. - Add USBH PHY controller. - Add RNG controller. - Add cfi-flash controller. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6362: populate device tree nodesÁlvaro Fernández Rojas2021-04-061-11/+116
| | | | | | | | | | | | | | | | - Rename periph_clk to periph_osc. - Rename clkctl to periph_clk. - Move syscon-reboot to subnode. - Add hsspi-osc clock. - Add watchdog. - Add SPI controller. - Add HS SPI controller. - Add NAND controller. - Add USBH PHY. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6358: populate device tree nodesÁlvaro Fernández Rojas2021-04-061-11/+72
| | | | | | | | | | | | | | - Rename periph_clk to periph_osc. - Rename clkctl to periph_clk. - Move syscon-reboot to subnode. - Add watchdog. - Add SPI controller. - Add USBH PHY. - Add cfi-flash. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6328: populate device tree nodesÁlvaro Fernández Rojas2021-04-061-14/+105
| | | | | | | | | | | | | | | - Rename periph_clk to periph_osc. - Rename clkctl to periph_clk. - Move syscon-reboot to subnode. - Add hsspi-osc clock. - Add watchdog. - Add HS SPI controller. - Add NAND controller. - Add USBH PHY. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: fix syscon-reboot nodesÁlvaro Fernández Rojas2021-04-065-5/+5
| | | | | | | | | | Commit a23c4134955e added the clock controller nodes, incorrectly changing the syscon-reboot nodes addresses. Fixes: a23c4134955e ("MIPS: BMIPS: add clock controller nodes") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: Loongson64: DeviceTree for Loongson-2K1000Qing Zhang2021-03-253-0/+254
| | | | | | | | | | Add DeviceTree files for Loongson-2K1000 processor, currently only supports single-core boot. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Qing Zhang <zhangqing@loongson.cn> Tested-by: Ming Wang <wangming01@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* MIPS: ingenic: gcw0: SPI panel does not require active-high CSPaul Cercueil2021-03-121-1/+0
| | | | | | | | | | | | | | The NT39016 panel is a fun beast, even though the documentation states that the CS line is active-low, it will work just fine if the CS line is configured as active-high, but it won't work if the CS line is forced low or forced high. Since it did actually work with the spi-cs-high property, this is not a bugfix, but we should nonetheless remove that property to match the documentation. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm63268: include dt-bindingsÁlvaro Fernández Rojas2021-03-121-0/+5
| | | | | | | | Now that there are proper device tree bindings we can start using them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6368: include dt-bindingsÁlvaro Fernández Rojas2021-03-121-0/+4
| | | | | | | | Now that there are proper device tree bindings we can start using them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6362: include dt-bindingsÁlvaro Fernández Rojas2021-03-121-0/+5
| | | | | | | | Now that there are proper device tree bindings we can start using them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6358: include dt-bindingsÁlvaro Fernández Rojas2021-03-121-0/+4
| | | | | | | | Now that there are proper device tree bindings we can start using them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* mips: bmips: bcm6328: include dt-bindingsÁlvaro Fernández Rojas2021-03-121-0/+5
| | | | | | | | Now that there are proper device tree bindings we can start using them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-20 21:51:20 +0100