| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When the CM block migrated from CM2.5 to CM3.0, the address offset for
the Global CSR Access Privilege register was modified. We saw this in
the "MIPS64 I6500 Multiprocessing System Programmer's Guide," it is
stated that "the Global CSR Access Privilege register is located at
offset 0x0120" in section 5.4. It is at least the same for I6400.
This fix allows to use the VP cores in SMP mode if the reset values
were modified by the bootloader.
Based on the work of Vladimir Kondratiev
<vladimir.kondratiev@mobileye.com> and the feedback from Jiaxun Yang
<jiaxun.yang@flygoat.com>.
Fixes: 197e89e0984a ("MIPS: mips-cm: Implement mips_cm_revision")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Based on the design pattern utilized in the CM GCR base address getter
implementation, the platform-specific code is capable to re-define the
getter and re-use the weakly defined initial version. But since the
pattern hasn't been used for over 10 years and another similar case (CM
L2-sync only base address getter) has just been fixed, let's unify the
interface and convert it to a more traditional single weakly defined
method: mips_cm_phys_base() (see the link below for the discussion around
this).
Link: https://lore.kernel.org/linux-mips/20240215171740.14550-3-fancer.lancer@gmail.com
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The __mips_cm_l2sync_phys_base() and mips_cm_l2sync_phys_base() couple was
introduced in commit 9f98f3dd0c51 ("MIPS: Add generic CM probe & access
code") where the former method was a weak implementation of the later
function. Such design pattern permitted to re-define the original method
and to use the weak implementation in the new function. A similar approach
was introduced in the framework of another arch-specific programmable
interface: mips_cm_phys_base() and __mips_cm_phys_base(). The only
difference is that the underscored method of the later couple was declared
in the "asm/mips-cm.h" header file, but it wasn't done for the CM L2-sync
methods in the subject. Due to the missing global function declaration
the "missing prototype" warning was spotted in the framework of the commit
9a2036724cd6 ("mips: mark local function static if possible") and fixed
just be re-qualifying the weak method as static. Doing that broke what was
originally implied by having the weak implementation globally defined.
Let's fix the broken CM2 L2-sync arch-interface by dropping the static
qualifier and, seeing the implemented pattern hasn't been used for over 10
years but will be required soon (see the link for the discussion around
it), converting it to a single weakly defined method:
mips_cm_l2sync_phys_base().
Fixes: 9a2036724cd6 ("mips: mark local function static if possible")
Link: https://lore.kernel.org/linux-mips/20240215171740.14550-3-fancer.lancer@gmail.com
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Now the exception vector for CPS systems are allocated on-fly
with memblock as well.
It will try to allocate from KSEG1 first, and then try to allocate
in low 4G if possible.
The main reset vector is now generated by uasm, to avoid tons
of patches to the code. Other vectors are copied to the location
later.
move 64bits fix in an other patch
fix cache issue with mips_cps_core_entry
rewrite the patch to reduce the diff stat
move extern in header
use cache address for copying vector
gc: use the new macro CKSEG[0A1]DDR_OR_64BIT()
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
mips_cm_error_report() extracts the cause and other cause from the error
register using shifts. This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits. Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.
Fix this by using FIELD_GET() instead. Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.
Fixes: 3885c2b463f6a236 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The default CM target field in the GCR_BASE register is encoded with 0
meaning memory & 1 being reserved. However the definitions we use for
those bits effectively get these two values backwards - likely because
they were copied from the definitions for the CM regions where the
target is encoded differently. This results in use setting up GCR_BASE
with the reserved target value by default, rather than targeting memory
as intended. Although we currently seem to get away with this it's not a
great idea to rely upon.
Fix this by changing our macros to match the documentated target values.
The incorrect encoding became used as of commit 9f98f3dd0c51 ("MIPS: Add
generic CM probe & access code") in the Linux v3.15 cycle, and was
likely carried forwards from older but unused code introduced by
commit 39b8d5254246 ("[MIPS] Add support for MIPS CMP platform.") in the
v2.6.26 cycle.
Fixes: 9f98f3dd0c51 ("MIPS: Add generic CM probe & access code")
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # v3.15+
Patchwork: https://patchwork.linux-mips.org/patch/17562/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17540/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Modify the functions we use to read information about the topology of
the system (the number of cores, VPs & IOCUs that it contains) in order
to take into account multiple clusters, and provide a new function to
determine the number of clusters in the system.
Users of these functions are modified only such that they continue to
build successfully - having them actually handle multiple clusters is
left to further patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17016/
Patchwork: https://patchwork.linux-mips.org/patch/17218/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With Coherence Manager (CM) 3.5 information about the topology of the
system, which has previously only been available through & accessed from
the CM, is now also provided by the Cluster Power Controller (CPC). This
includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a
new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG.
In preparation for adjusting functions such as mips_cm_numcores(), which
have previously only needed to access the CM, to also access the CPC
this patch modifies the way we use the various CPS headers. Rather than
having users include asm/mips-cm.h or asm/mips-cpc.h individually we
instead have users include asm/mips-cps.h which in turn includes
asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access
to both CM & CPC registers by including one header, and most importantly
it makes asm/mips-cps.h an ideal location for helper functions which
need to access the various components of the CPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17015/
Patchwork: https://patchwork.linux-mips.org/patch/17217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With CM >= 3.5 we have the notion of multiple clusters & can access
their CM, CPC & GIC registers via the apporpriate redirect/other
register blocks. In order to allow for this introduce cluster & block
arguments to mips_cm_lock_other() which configures the redirect/other
region to point at the appropriate cluster, core, VP & register block.
Since we now have 4 arguments to mips_cm_lock_other() & a common use is
likely to be to target the cluster, core & VP corresponding to a
particular Linux CPU number we also add a new mips_cm_lock_other_cpu()
helper function which handles that without the caller needing to
manually pull out the cluster, core & VP numbers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17013/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We currently have fields in struct cpuinfo_mips for the core & VP(E) ID
of a particular CPU, and various pieces of code directly access those
fields. This patch abstracts such access by introducing accessor
functions cpu_core(), cpu_set_core(), cpu_vpe_id() & cpu_set_vpe_id()
and having code that needs to access these values call those functions
rather than directly accessing the struct cpuinfo_mips fields. This
prepares us for changes to the way in which those values are stored in
later patches.
The cpu_vpe_id() function is introduced even though we already had a
cpu_vpe_id() macro for a couple of reasons:
1) It's more consistent with the core, and future cluster, accessors.
2) It ensures a sensible return type without explicit casts.
3) It's generally preferable to use functions rather than macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Introduce definitions & accessors for a selection of Coherence Manager
(CM) & Cluster Power Controller (CPC) registers that are new with CM
v3.5 & the MIPS I6500. These are primarily registers that will be used
in supporting multiple CPU clusters.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17006/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h
when declaring macros corresponding to register fields. This patch
modifies our definitions to do so.
The *_SHF definitions are removed entirely - they duplicate information
found in the masks, are infrequently used & can be replaced with use of
__ffs() where needed.
The *_MSK definitions then lose their _MSK suffix which is now somewhat
redundant, and users are modified to match.
The field definitions are moved to follow the appropriate register's
accessor functions, which helps to keep the field definitions in order &
to find the appropriate fields for a given register. Whilst here a
comment is added describing each register & including its name, which is
helpful both for linking the register back to hardware documentation &
for grepping purposes.
This also cleans up a couple of issues that became obvious as a result
of making the changes described above:
- We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony
copy of that named GCR_RESET_EXT_BASE - a register which does not
exist. The bad definitions were added by commit 497e803ebf98 ("MIPS:
smp-cps: Ensure secondary cores start with EVA disabled") and made
use of from boot_core(), which is now modified to use the
GCR_Cx_RESET_EXT_BASE definitions.
- We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly
define this as inFo rather than inGo.
Now that we don't duplicate field information between _SHF & _MSK
definitions, and keep the fields next to the register accessors, it will
be much easier to spot & prevent any similar oddities being introduced
in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17001/
Patchwork: https://patchwork.linux-mips.org/patch/17216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some CM registers are always 32 bits, or at least only use bits in the
lower 32 bits of the register. For these registers it is wasteful for us
to generate accessors which bother to check mips_cm_is64 & perform 64
bit accesses.
This patch modifies the accessor generation to take into account the
size of the register, and for 32 bit registers we generate accessors
which only ever perform 32 bit accesses. For 64 bit registers we either
perform a 64 bit access or two 32 bit accesses, depending upon the value
of mips_cm_is64. Doing this saves us ~1.5KiB of code in a generic 64r6el
kernel, and perhaps more importantly simplifies various code paths.
This removes the read64_gcr_* accessors, so mips_cm_error_report() is
modified to stop using them & instead use the regular read_gcr_*
accessors which will return 64 bit values from the 64 bit registers.
The new accessor macros are placed in asm/mips-cps.h such that they can
be shared by CPC & GIC code in later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17000/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We currently have a mips_cm_base variable which holds the base address
of the Coherence Manager (CM) Global Configuration Registers (GCRs), and
accessor functions which use the GCR in their names. This works fine,
but gets in the way of sharing the code to generate the accessor
functions with other blocks (ie. CPC & GIC) because that code would then
need to separately handle the name of the base address variable & the
name used in the accessor functions.
In order to prepare for sharing the accessor generation code between CM,
CPC & GIC code this patch renames mips_cm_base to mips_gcr_base such
that the "gcr" portion is common to both the base address variable & the
accessor function names.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16999/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On systems with CM3, we must ensure that the L1 & L2 ECC enables are set
to the same value. This is presumed by the hardware & cache corruption
can occur when it is not the case. Support enabling & disabling the L2
ECC checking on CM3 systems where this is controlled via a GCR, and
ensure that it matches the state of L1 ECC checking. Remove I6400 from
the switch statement it will no longer hit, and which was incorrect
since the L2 ECC enable bit isn't in the CP0 ErrCtl register.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14413/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
MIPS CM3 changed the management of coherence. Instead of a coherence
control register with a bitmask of coherent domains, CM3 simply has a
coherence enable register with a single bit to enable coherence of the
local core. Support this by clearing and setting this single bit to
disable / enable coherence.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14226/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When discovering the number of VPEs per core, smp_num_siblings will be
incorrect for kernels built without support for the MIPS MultiThreading
(MT) ASE running on systems which implement said ASE. This leads to
accesses to VPEs in secondary cores being performed incorrectly since
mips_cm_vp_id calculates the wrong ID to write to the local "other"
registers. Fix this by examining the number of VPEs in the core as
reported by the CM.
This patch presumes that the number of VPEs will be the same in each
core of the system. As this path only applies to systems with CM version
2.5 or lower, and this property is true of all such known systems, this
is likely to be fine but is described in a comment for good measure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Fix mips_cm_lock_other compilation error when MIPS_CM is not selected.
This was introduced in commit 23d5de8efb9a (MIPS: CM: Introduce core-other
locking functions)
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix mips_cm_max_vp_width for UP kernels where it previously referenced
smp_num_siblings, which is not declared for UP kernels. This led to
build errors such as the following:
drivers/built-in.o: In function `$L446':
irq-mips-gic.c:(.text+0x1994): undefined reference to `smp_num_siblings'
drivers/built-in.o:irq-mips-gic.c:(.text+0x199c): more undefined references to `smp_num_siblings' follow
On UP kernels simply return 1, leaving the reference to smp_num_siblings
in place only for SMP kernels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12332/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Generate accessor functions for the GCR_BEV_BASE register introduced by
CM3, for use by a later patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
According to 'MIPS32® interAptivTM Multiprocessing
System Programmer’s Guide' CPC_BASE_ADDR takes bits [31:15].
This change is tested ith mt7621 which wasn't working without it.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11766/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
| |
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12617/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The kernel currently assumes that a core will start up in legacy mode
using the exception base provided through the CM GCR registers. If a
core has been configured in hardware to start in EVA mode, these
assumptions will fail.
This patch ensures that secondary cores are initialized to meet these
assumptions.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11907/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Introduce mips_cm_lock_other & mips_cm_unlock_other, mirroring the
existing CPC equivalents, in order to lock access from the current core
to another via the core-other GCR region. This hasn't been required in
the past but with CM3 the CPC starts using GCR_CL_OTHER rather than
CPC_CL_OTHER and this will be required for safety.
[ralf@linux-mips.org: Fix merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11207/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The PVPE (or PVP in >= CM3) field is 10 bits wide, but the mask
previously only covered the bottom 9 bits. Extend the mask to cover all
10 bits of the field.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11206/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CM3 has 64 bit GCR_ERROR_* registers, but the code in
mips_cm_error_report was previously only reading 32 bits of it in MIPS32
kernels. Fix by splitting the reads for CM2 & CM3, and making use of the
read64_ variants of the accessor function for CM3.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11189/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If we run a MIPS32 kernel on a system using CM3 we may still need to
access 64 bit GCRs, as will be done in later patches. Allow this by
having the read64_gcr_* accessor functions perform 2 x 32 bit reads on
those systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11188/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The documentation for mips_cm_is64 implied that the width of the CM GCRs
would change depending upon the CPU, which is not true. Reword the
explanation to be clearer that the GCR width is purely dependent upon
the version of the CM.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11185/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On systems with CM 2.5 & beyond there may be L2 prefetch units present
which are not enabled by default. Detect them, configuring & enabling
prefetching when available.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11180/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The VP ID of a given CPU may not match up with the CPU number used by
Linux. For example, if the width of the VP part of the VP ID is wider
than log2(number of VPs per core) and the system has multiple cores then
this will be the case. Alternatively, if a pre-r6 system implements the
MT ASE with multiple VPEs per core and Linux is built without support
for the MT ASE then the numbers won't match up either. Provide a
function to convert from CPU number to VP ID.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11211/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The CM cache error reporting code is not Malta specific and as such it
should live in the mips-cm.c file. Moreover, CM2 and CM3 differ in the
way cache errors are being recorded to the registers so extend the
previous code to add support for the CM3 as well.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10646/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Previously, the CM accessors were only accessing CM registers as u32
types instead of using the native CM register with. However, newer CMs
may actually be 64-bit on MIPS64 cores. Fortunately, current 64-bit CMs
(CM3) hold all the useful configuration bits in the lower half of the
64-bit registers (at least most of them) so they can still be accessed
using the current 32-bit accessors.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Provide accessor functions for the GCR_L2_CONFIG register introduced
with CM3, and define the bits included in the register.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Provide a function to trivially return the version of the CM present in
the system, or 0 if no CM is present. The mips_cm_revision() will be
used later on to determine the CM register width, so it must not use
the regular CM accessors to read the revision register since that will
lead to build failures due to recursive inlines.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10655/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A later patch in this series will include mips-cm.h but does not require
errno.h. This leads to a build failure with ENODEV undeclared. Include
errno.h from mips-cm.h to pull in the appropriate definition and avoid
the build failure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/10113/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add definitions for the GICEX field in the GCR_GIC_STATUS register to
mips-cm.h for use in a later patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/10112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sparse emits a bunch of warnings in mips-cm.h due to casting away of
__iomem by the addr_gcr_*() functions:
arch/mips/include/asm/mips-cm.h:134:1: warning: cast removes address space of expression
And subsequent passing of the return values to __raw_readl() and
__raw_writel() in the read_gcr_*() and write_gcr_*() functions:
arch/mips/include/asm/mips-cm.h:134:1: warning: incorrect type in argument 2 (different address spaces)
arch/mips/include/asm/mips-cm.h:134:1: expected void volatile [noderef] <asn:2>*mem
arch/mips/include/asm/mips-cm.h:134:1: got unsigned int [usertype] *
arch/mips/include/asm/mips-cm.h:134:1: warning: incorrect type in argument 1 (different address spaces)
arch/mips/include/asm/mips-cm.h:134:1: expected void const volatile [noderef] <asn:2>*mem
arch/mips/include/asm/mips-cm.h:134:1: got unsigned int [usertype] *
Fix by adding __iomem to the addr_gcr_*() return type and cast.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
| |
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
The CM registers use native endianness, so using plain readl & writel
will produce incorrect results on big endian systems.
Reported-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6656/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
|
The kernel currently only probes for a MIPS Coherence Manager in the
Malta interrupt code in order to detect & enable the GIC. However CM is
not Malta-specific, so this should really be more generic. This patch
introduces some non-Malta-specific code which probes for a CM and
performs some basic initialisation.
A new header, with temporarily duplicated register definitions, is
introduced in order to:
1) Allow the new definitions to be correct with regards to the
CM documentation, as many of those in gcmpregs.h aren't.
2) Allow switching away from the REG() macro used via a few layers of
nested macros in order to access registers in gcmpregs.h. This
patch instead introduced accessor functions akin to the
{read,write}_c0_* functions used for cop0 registers.
3) Allow users of the CM to be migrated one by one.
4) Switch from the name 'GCMP' to 'CM' since the Coherence Manager is
what this code is actually dealing with.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6360/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
