| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Anatoly Trosinenko reports that a corrupted squashfs image can cause a
kernel oops. It turns out that squashfs can end up being confused about
negative fragment lengths.
The regular squashfs_read_data() does check for negative lengths, but
squashfs_read_metadata() did not, and the fragment size code just
blindly trusted the on-disk value. Fix both the fragment parsing and
the metadata reading code.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Phillip Lougher <phillip@squashfs.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 8844618d8aa7: "ext4: only look at the bg_flags field if it is
valid" will complain if block group zero does not have the
EXT4_BG_INODE_ZEROED flag set. Unfortunately, this is not correct,
since a freshly created file system has this flag cleared. It gets
almost immediately after the file system is mounted read-write --- but
the following somewhat unlikely sequence will end up triggering a
false positive report of a corrupted file system:
mkfs.ext4 /dev/vdc
mount -o ro /dev/vdc /vdc
mount -o remount,rw /dev/vdc
Instead, when initializing the inode table for block group zero, test
to make sure that itable_unused count is not too large, since that is
the case that will result in some or all of the reserved inodes
getting cleared.
This fixes the failures reported by Eric Whiteney when running
generic/230 and generic/231 in the the nojournal test case.
Fixes: 8844618d8aa7 ("ext4: only look at the bg_flags field if it is valid")
Reported-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This reverts commit 2a027b47dba6 ("MIPS: BCM47XX: Enable 74K Core
ExternalSync for PCIe erratum").
Enabling ExternalSync caused a regression for BCM4718A1 (used e.g. in
Netgear E3000 and ASUS RT-N16): it simply hangs during PCIe
initialization. It's likely that BCM4717A1 is also affected.
I didn't notice that earlier as the only BCM47XX devices with PCIe I
own are:
1) BCM4706 with 2 x 14e4:4331
2) BCM4706 with 14e4:4360 and 14e4:4331
it appears that BCM4706 is unaffected.
While BCM5300X-ES300-RDS.pdf seems to document that erratum and its
workarounds (according to quotes provided by Tokunori) it seems not even
Broadcom follows them.
According to the provided info Broadcom should define CONF7_ES in their
SDK's mipsinc.h and implement workaround in the si_mips_init(). Checking
both didn't reveal such code. It *could* mean Broadcom also had some
problems with the given workaround.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Michael Marley <michael@michaelmarley.com>
Patchwork: https://patchwork.linux-mips.org/patch/20032/
URL: https://bugs.openwrt.org/index.php?do=details&task_id=1688
Cc: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
After the bio has been updated to represent the remaining sectors, reset
bi_done so bio_rewind_iter() does not rewind further than it should.
This resolves a bio_integrity_process() failure on reads where the
original request was split.
Fixes: 63573e359d05 ("bio-integrity: Restore original iterator on verify stage")
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The size of kvm's shadow page tables corresponds to the size of the
guest virtual machines on the system. Large VMs can spend a significant
amount of memory as shadow page tables which can not be left as system
memory overhead. So, account shadow page tables to the kmemcg.
[shakeelb@google.com: replace (GFP_KERNEL|__GFP_ACCOUNT) with GFP_KERNEL_ACCOUNT]
Link: http://lkml.kernel.org/r/20180629140224.205849-1-shakeelb@google.com
Link: http://lkml.kernel.org/r/20180627181349.149778-1-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Peter Feiner <pfeiner@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
/sys/../zswap/stored_pages keeps rising in a zswap test with
"zswap.max_pool_percent=0" parameter. But it should not compress or
store pages any more since there is no space in the compressed pool.
Reproduce steps:
1. Boot kernel with "zswap.enabled=1"
2. Set the max_pool_percent to 0
# echo 0 > /sys/module/zswap/parameters/max_pool_percent
3. Do memory stress test to see if some pages have been compressed
# stress --vm 1 --vm-bytes $mem_available"M" --timeout 60s
4. Watching the 'stored_pages' number increasing or not
The root cause is:
When zswap_max_pool_percent is set to 0 via kernel parameter,
zswap_is_full() will always return true due to zswap_shrink(). But if
the shinking is able to reclain a page successfully the code then
proceeds to compressing/storing another page, so the value of
stored_pages will keep changing.
To solve the issue, this patch adds a zswap_is_full() check again after
zswap_shrink() to make sure it's now under the max_pool_percent, and to
not compress/store if we reached the limit.
Link: http://lkml.kernel.org/r/20180530103936.17812-1-liwang@redhat.com
Signed-off-by: Li Wang <liwang@redhat.com>
Acked-by: Dan Streetman <ddstreet@ieee.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The new gasket staging driver ran into a randconfig build failure when
CONFIG_EVENTFD is disabled:
In file included from drivers/staging/gasket/gasket_interrupt.h:11,
from drivers/staging/gasket/gasket_interrupt.c:4:
include/linux/eventfd.h: In function 'eventfd_ctx_fdget':
include/linux/eventfd.h:51:9: error: implicit declaration of function 'ERR_PTR' [-Werror=implicit-function-declaration]
I can't see anything wrong with including eventfd.h before err.h, so the
easiest fix is to make it possible to do this by including the file
where it is needed.
Link: http://lkml.kernel.org/r/20180724110737.3985088-1-arnd@arndb.de
Fixes: 9a69f5087ccc ("drivers/staging: Gasket driver framework + Apex driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
vma_is_anonymous() relies on ->vm_ops being NULL to detect anonymous
VMA. This is unreliable as ->mmap may not set ->vm_ops.
False-positive vma_is_anonymous() may lead to crashes:
next ffff8801ce5e7040 prev ffff8801d20eca50 mm ffff88019c1e13c0
prot 27 anon_vma ffff88019680cdd8 vm_ops 0000000000000000
pgoff 0 file ffff8801b2ec2d00 private_data 0000000000000000
flags: 0xff(read|write|exec|shared|mayread|maywrite|mayexec|mayshare)
------------[ cut here ]------------
kernel BUG at mm/memory.c:1422!
invalid opcode: 0000 [#1] SMP KASAN
CPU: 0 PID: 18486 Comm: syz-executor3 Not tainted 4.18.0-rc3+ #136
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
RIP: 0010:zap_pmd_range mm/memory.c:1421 [inline]
RIP: 0010:zap_pud_range mm/memory.c:1466 [inline]
RIP: 0010:zap_p4d_range mm/memory.c:1487 [inline]
RIP: 0010:unmap_page_range+0x1c18/0x2220 mm/memory.c:1508
Call Trace:
unmap_single_vma+0x1a0/0x310 mm/memory.c:1553
zap_page_range_single+0x3cc/0x580 mm/memory.c:1644
unmap_mapping_range_vma mm/memory.c:2792 [inline]
unmap_mapping_range_tree mm/memory.c:2813 [inline]
unmap_mapping_pages+0x3a7/0x5b0 mm/memory.c:2845
unmap_mapping_range+0x48/0x60 mm/memory.c:2880
truncate_pagecache+0x54/0x90 mm/truncate.c:800
truncate_setsize+0x70/0xb0 mm/truncate.c:826
simple_setattr+0xe9/0x110 fs/libfs.c:409
notify_change+0xf13/0x10f0 fs/attr.c:335
do_truncate+0x1ac/0x2b0 fs/open.c:63
do_sys_ftruncate+0x492/0x560 fs/open.c:205
__do_sys_ftruncate fs/open.c:215 [inline]
__se_sys_ftruncate fs/open.c:213 [inline]
__x64_sys_ftruncate+0x59/0x80 fs/open.c:213
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reproducer:
#include <stdio.h>
#include <stddef.h>
#include <stdint.h>
#include <stdlib.h>
#include <string.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <sys/mman.h>
#include <unistd.h>
#include <fcntl.h>
#define KCOV_INIT_TRACE _IOR('c', 1, unsigned long)
#define KCOV_ENABLE _IO('c', 100)
#define KCOV_DISABLE _IO('c', 101)
#define COVER_SIZE (1024<<10)
#define KCOV_TRACE_PC 0
#define KCOV_TRACE_CMP 1
int main(int argc, char **argv)
{
int fd;
unsigned long *cover;
system("mount -t debugfs none /sys/kernel/debug");
fd = open("/sys/kernel/debug/kcov", O_RDWR);
ioctl(fd, KCOV_INIT_TRACE, COVER_SIZE);
cover = mmap(NULL, COVER_SIZE * sizeof(unsigned long),
PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0);
munmap(cover, COVER_SIZE * sizeof(unsigned long));
cover = mmap(NULL, COVER_SIZE * sizeof(unsigned long),
PROT_READ | PROT_WRITE, MAP_PRIVATE, fd, 0);
memset(cover, 0, COVER_SIZE * sizeof(unsigned long));
ftruncate(fd, 3UL << 20);
return 0;
}
This can be fixed by assigning anonymous VMAs own vm_ops and not relying
on it being NULL.
If ->mmap() failed to set ->vm_ops, mmap_region() will set it to
dummy_vm_ops. This way we will have non-NULL ->vm_ops for all VMAs.
Link: http://lkml.kernel.org/r/20180724121139.62570-4-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: syzbot+3f84280d52be9b7083cc@syzkaller.appspotmail.com
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make sure to initialize all VMAs properly, not only those which come
from vm_area_cachep.
Link: http://lkml.kernel.org/r/20180724121139.62570-3-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Not all VMAs allocated with vm_area_alloc(). Some of them allocated on
stack or in data segment.
The new helper can be use to initialize VMA properly regardless where it
was allocated.
Link: http://lkml.kernel.org/r/20180724121139.62570-2-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit e76384884344 ("mm: introduce MEMORY_DEVICE_FS_DAX and
CONFIG_DEV_PAGEMAP_OPS") added two EXPORT_SYMBOL_GPL() symbols, but
these symbols are required by the inlined put_page(), thus accidentally
making put_page() a GPL export only. This breaks OpenAFS (at least).
Mark them EXPORT_SYMBOL() instead.
Link: http://lkml.kernel.org/r/153128611970.2928.11310692420711601254.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: e76384884344 ("mm: introduce MEMORY_DEVICE_FS_DAX and CONFIG_DEV_PAGEMAP_OPS")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Joe Gorse <jhgorse@gmail.com>
Reported-by: John Hubbard <jhubbard@nvidia.com>
Tested-by: Joe Gorse <jhgorse@gmail.com>
Tested-by: John Hubbard <jhubbard@nvidia.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Mark Vitale <mvitale@sinenomine.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order for load/store tearing prevention to work, _all_ accesses to
the variable in question need to be done around READ and WRITE_ONCE()
macros. Ensure everyone does so for q->status variable for
semtimedop().
Link: http://lkml.kernel.org/r/20180717052654.676-1-dave@stgolabs.net
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When pmem namespaces created are smaller than section size, this can
cause an issue during removal and gpf was observed:
general protection fault: 0000 1 SMP PTI
CPU: 36 PID: 3941 Comm: ndctl Tainted: G W 4.14.28-1.el7uek.x86_64 #2
task: ffff88acda150000 task.stack: ffffc900233a4000
RIP: 0010:__put_page+0x56/0x79
Call Trace:
devm_memremap_pages_release+0x155/0x23a
release_nodes+0x21e/0x260
devres_release_all+0x3c/0x48
device_release_driver_internal+0x15c/0x207
device_release_driver+0x12/0x14
unbind_store+0xba/0xd8
drv_attr_store+0x27/0x31
sysfs_kf_write+0x3f/0x46
kernfs_fop_write+0x10f/0x18b
__vfs_write+0x3a/0x16d
vfs_write+0xb2/0x1a1
SyS_write+0x55/0xb9
do_syscall_64+0x79/0x1ae
entry_SYSCALL_64_after_hwframe+0x3d/0x0
Add code to check whether we have a mapping already in the same section
and prevent additional mappings from being created if that is the case.
Link: http://lkml.kernel.org/r/152909478401.50143.312364396244072931.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Robert Elliott <elliott@hpe.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Building with KASAN and SLUB but without sysfs now results in a
build-time error:
WARNING: unmet direct dependencies detected for SLUB_DEBUG
Depends on [n]: SLUB [=y] && SYSFS [=n]
Selected by [y]:
- KASAN [=y] && HAVE_ARCH_KASAN [=y] && (SLUB [=y] || SLAB [=n] && !DEBUG_SLAB [=n]) && SLUB [=y]
mm/slub.c:4565:12: error: 'list_locations' defined but not used [-Werror=unused-function]
static int list_locations(struct kmem_cache *s, char *buf,
^~~~~~~~~~~~~~
mm/slub.c:4406:13: error: 'validate_slab_cache' defined but not used [-Werror=unused-function]
static long validate_slab_cache(struct kmem_cache *s)
This disallows that broken configuration in Kconfig.
Link: http://lkml.kernel.org/r/20180709154019.1693026-1-arnd@arndb.de
Fixes: dd275caf4a0d ("kasan: depend on CONFIG_SLUB_DEBUG")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While forking, if delayacct init fails due to memory shortage, it
continues expecting all delayacct users to check task->delays pointer
against NULL before dereferencing it, which all of them used to do.
Commit c96f5471ce7d ("delayacct: Account blkio completion on the correct
task"), while updating delayacct_blkio_end() to take the target task
instead of always using %current, made the function test NULL on
%current->delays and then continue to operated on @p->delays. If
%current succeeded init while @p didn't, it leads to the following
crash.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: __delayacct_blkio_end+0xc/0x40
PGD 8000001fd07e1067 P4D 8000001fd07e1067 PUD 1fcffbb067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 4 PID: 25774 Comm: QIOThread0 Not tainted 4.16.0-9_fbk1_rc2_1180_g6b593215b4d7 #9
RIP: 0010:__delayacct_blkio_end+0xc/0x40
Call Trace:
try_to_wake_up+0x2c0/0x600
autoremove_wake_function+0xe/0x30
__wake_up_common+0x74/0x120
wake_up_page_bit+0x9c/0xe0
mpage_end_io+0x27/0x70
blk_update_request+0x78/0x2c0
scsi_end_request+0x2c/0x1e0
scsi_io_completion+0x20b/0x5f0
blk_mq_complete_request+0xa2/0x100
ata_scsi_qc_complete+0x79/0x400
ata_qc_complete_multiple+0x86/0xd0
ahci_handle_port_interrupt+0xc9/0x5c0
ahci_handle_port_intr+0x54/0xb0
ahci_single_level_irq_intr+0x3b/0x60
__handle_irq_event_percpu+0x43/0x190
handle_irq_event_percpu+0x20/0x50
handle_irq_event+0x2a/0x50
handle_edge_irq+0x80/0x1c0
handle_irq+0xaf/0x120
do_IRQ+0x41/0xc0
common_interrupt+0xf/0xf
Fix it by updating delayacct_blkio_end() check @p->delays instead.
Link: http://lkml.kernel.org/r/20180724175542.GP1934745@devbig577.frc2.facebook.com
Fixes: c96f5471ce7d ("delayacct: Account blkio completion on the correct task")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dave Jones <dsj@fb.com>
Debugged-by: Dave Jones <dsj@fb.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Josh Snyder <joshs@netflix.com>
Cc: <stable@vger.kernel.org> [4.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
bio_iov_iter_get_pages() currently only adds pages for the next non-zero
segment from the iov_iter to the bio. That's suboptimal for callers,
which typically try to pin as many pages as fit into the bio. This patch
converts the current bio_iov_iter_get_pages() into a static helper, and
introduces a new helper that allocates as many pages as
1) fit into the bio,
2) are present in the iov_iter,
3) and can be pinned by MM.
Error is returned only if zero pages could be pinned. Because of 3), a
zero return value doesn't necessarily mean all pages have been pinned.
Callers that have to pin every page in the iov_iter must still call this
function in a loop (this is currently the case).
This change matters most for __blkdev_direct_IO_simple(), which calls
bio_iov_iter_get_pages() only once. If it obtains less pages than
requested, it returns a "short write" or "short read", and
__generic_file_write_iter() falls back to buffered writes, which may
lead to data corruption.
Fixes: 72ecad22d9f1 ("block: support a full bio worth of IO for simplified bdev direct-io")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fixes: 72ecad22d9f1 ("block: support a full bio worth of IO for simplified bdev direct-io")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If the last page of the bio is not "full", the length of the last
vector slot needs to be corrected. This slot has the index
(bio->bi_vcnt - 1), but only in bio->bi_io_vec. In the "bv" helper
array, which is shifted by the value of bio->bi_vcnt at function
invocation, the correct index is (nr_pages - 1).
v2: improved readability following suggestions from Ming Lei.
v3: followed a formatting suggestion from Christoph Hellwig.
Fixes: 2cefe4dbaadf ("block: add bio_iov_iter_get_pages()")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When an fatal error is received by a non-bridge device, the device is
removed, and pci_stop_and_remove_bus_device() deallocates the device
structure. The freed device structure is used by subsequent code to send
uevents and print messages.
Hold a reference on the device until we're finished using it. This is not
an ideal fix because pcie_do_fatal_recovery() should not use the device at
all after removing it, but that's too big a project for right now.
Fixes: 7e9084b36740 ("PCI/AER: Handle ERR_FATAL with removal and re-enumeration of devices")
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
[bhelgaas: changelog, reduce get/put coverage]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
There is a window for racing when printing directly to task->comm,
allowing other threads to see a non-terminated string. The vsnprintf
function fills the buffer, counts the truncated chars, then finally
writes the \0 at the end.
creator other
vsnprintf:
fill (not terminated)
count the rest trace_sched_waking(p):
... memcpy(comm, p->comm, TASK_COMM_LEN)
write \0
The consequences depend on how 'other' uses the string. In our case,
it was copied into the tracing system's saved cmdlines, a buffer of
adjacent TASK_COMM_LEN-byte buffers (note the 'n' where 0 should be):
crash-arm64> x/1024s savedcmd->saved_cmdlines | grep 'evenk'
0xffffffd5b3818640: "irq/497-pwr_evenkworker/u16:12"
...and a strcpy out of there would cause stack corruption:
[224761.522292] Kernel panic - not syncing: stack-protector:
Kernel stack is corrupted in: ffffff9bf9783c78
crash-arm64> kbt | grep 'comm\|trace_print_context'
#6 0xffffff9bf9783c78 in trace_print_context+0x18c(+396)
comm (char [16]) = "irq/497-pwr_even"
crash-arm64> rd 0xffffffd4d0e17d14 8
ffffffd4d0e17d14: 2f71726900000000 5f7277702d373934 ....irq/497-pwr_
ffffffd4d0e17d24: 726f776b6e657665 3a3631752f72656b evenkworker/u16:
ffffffd4d0e17d34: f9780248ff003231 cede60e0ffffff9b 12..H.x......`..
ffffffd4d0e17d44: cede60c8ffffffd4 00000fffffffffd4 .....`..........
The workaround in e09e28671 (use strlcpy in __trace_find_cmdline) was
likely needed because of this same bug.
Solved by vsnprintf:ing to a local buffer, then using set_task_comm().
This way, there won't be a window where comm is not terminated.
Link: http://lkml.kernel.org/r/20180726071539.188015-1-snild@sony.com
Cc: stable@vger.kernel.org
Fixes: bc0c38d139ec7 ("ftrace: latency tracer infrastructure")
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Snild Dolkow <snild@sony.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Commit 57ea2a34adf4 ("tracing/kprobes: Fix trace_probe flags on
enable_trace_kprobe() failure") added an if statement that depends on another
if statement that gcc doesn't see will initialize the "link" variable and
gives the warning:
"warning: 'link' may be used uninitialized in this function"
It is really a false positive, but to quiet the warning, and also to make
sure that it never actually is used uninitialized, initialize the "link"
variable to NULL and add an if (!WARN_ON_ONCE(!link)) where the compiler
thinks it could be used uninitialized.
Cc: stable@vger.kernel.org
Fixes: 57ea2a34adf4 ("tracing/kprobes: Fix trace_probe flags on enable_trace_kprobe() failure")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
There was a case that triggered a double free in event_trigger_callback()
due to the called reg() function freeing the trigger_data and then it
getting freed again by the error return by the caller. The solution there
was to up the trigger_data ref count.
Code inspection found that event_enable_trigger_func() has the same issue,
but is not as easy to trigger (requires harder to trigger failures). It
needs to be solved slightly different as it needs more to clean up when the
reg() function fails.
Link: http://lkml.kernel.org/r/20180725124008.7008e586@gandalf.local.home
Cc: stable@vger.kernel.org
Fixes: 7862ad1846e99 ("tracing: Add 'enable_event' and 'disable_event' event trigger commands")
Reivewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com
(cherry picked from commit 90c3e2198777aaa355b6994a31a79c636c8d4306)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
If enable_trace_kprobe fails to enable the probe in enable_k(ret)probe
it returns an error, but does not unset the tp flags it set previously.
This results in a probe being considered enabled and failures like being
unable to remove the probe through kprobe_events file since probes_open()
expects every probe to be disabled.
Link: http://lkml.kernel.org/r/20180725102826.8300-1-asavkov@redhat.com
Link: http://lkml.kernel.org/r/20180725142038.4765-1-asavkov@redhat.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 41a7dd420c57 ("tracing/kprobes: Support ftrace_event_file base multibuffer")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
