| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Check that the NFC_ATTR_TARGET_INDEX attributes (in addition to
NFC_ATTR_DEVICE_INDEX) are provided by the netlink client prior to
accessing them. This prevents potential unhandled NULL pointer dereference
exceptions which can be triggered by malicious user-mode programs,
if they omit one or both of these attributes.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing all VID filters, the mvpp2_prs_vid_entry_remove would be
called with the TCAM id incorrectly used as a VID, causing the wrong
TCAM entries to be invalidated.
Fix this by directly invalidating entries in the VID range.
Fixes: 56beda3db602 ("net: mvpp2: Add hardware offloading for VLAN filtering")
Suggested-by: Yuri Chipchev <yuric@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VID filtering is implemented in the Header Parser, with one range of 11
vids being assigned for each no-loopback port.
Make sure we use the per-port range when looking for existing entries in
the Parser.
Since we used a global range instead of a per-port one, this causes VIDs
to be removed from the whitelist from all ports of the same PPv2
instance.
Fixes: 56beda3db602 ("net: mvpp2: Add hardware offloading for VLAN filtering")
Suggested-by: Yuri Chipchev <yuric@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When PVID is removed from a bridge port, the Linux bridge drops both
untagged and prio-tagged packets. Align mlxsw with this behavior.
Fixes: 148f472da5db ("mlxsw: reg: Add the Switch Port Acceptable Frame Types register")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to an issue on Spectrum-2, in front-panel ports split four ways, 2 out
of 32 port buffers cannot be used. To work around this, the next FW release
will mark them as unused, and will report correspondingly lower total
shared buffer size. mlxsw will pick up the new value through a query to
cap_total_buffer_size resource. However the initial size for shared buffer
pool 0 is hard-coded and therefore needs to be updated.
Thus reduce the pool size by 2.7 MiB (which corresponds to 2/32 of the
total size of 42 MiB), and round down to the whole number of cells.
Fixes: fe099bf682ab ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TOS value was not extracted correctly. Fix it.
Fixes: 87996f91f739 ("mlxsw: spectrum_flower: Add support for ip tos")
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test that IPv4 and IPv6 nexthops are correctly marked with offload
indication in response to neighbour events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver tries to periodically refresh neighbours that are used to
reach nexthops. This is done by periodically calling neigh_event_send().
However, if the neighbour becomes dead, there is nothing we can do to
return it to a connected state and the above function call is basically
a NOP.
This results in the nexthop never being written to the device's
adjacency table and therefore never used to forward packets.
Fix this by dropping our reference from the dead neighbour and
associating the nexthop with a new neigbhour which we will try to
refresh.
Fixes: a7ff87acd995 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same hash function and seed are used for both ECMP and LAG hash.
Therefore, when a LAG device is used as a nexthop device as part of an
ECMP group, hash polarization can occur and all the traffic will be
hashed to a single LAG slave.
Fix this by using a different seed for the LAG hash.
Fixes: fa73989f2697 ("mlxsw: spectrum: Use a stable ECMP/LAG seed")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tls_sw_do_sendpage needs to return the total number of bytes sent
regardless of how many sk_msgs are allocated. Unfortunately, copied
(the value we return up the stack) is zero'd before each new sk_msg
is allocated so we only return the copied size of the last sk_msg used.
The caller (splice, etc.) of sendpage will then believe only part
of its data was sent and send the missing chunks again. However,
because the data actually was sent the receiver will get multiple
copies of the same data.
To reproduce this do multiple sendfile calls with a length close to
the max record size. This will in turn call splice/sendpage, sendpage
may use multiple sk_msg in this case and then returns the incorrect
number of bytes. This will cause splice to resend creating duplicate
data on the receiver. Andre created a C program that can easily
generate this case so we will push a similar selftest for this to
bpf-next shortly.
The fix is to _not_ zero the copied field so that the total sent
bytes is returned.
Reported-by: Steinar H. Gunderson <steinar+kernel@gunderson.no>
Reported-by: Andre Tomt <andre@tomt.net>
Tested-by: Andre Tomt <andre@tomt.net>
Fixes: d829e9c4112b ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get the ingress interface and increment ICMP counters based on that
instead of skb->dev when the the dev is a VRF device.
This is a follow up on the following message:
https://www.spinics.net/lists/netdev/msg560268.html
v2: Avoid changing skb->dev since it has unintended effect for local
delivery (David Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using ethtool, users can specify a classification action matching on the
full vlan tag, which includes the DEI bit (also previously called CFI).
However, when converting the ethool_flow_spec to a flow_rule, we use
dissector keys to represent the matching patterns.
Since the vlan dissector key doesn't include the DEI bit, this
information was silently discarded when translating the ethtool
flow spec in to a flow_rule.
This commit adds the DEI bit into the vlan dissector key, and allows
propagating the information to the driver when parsing the ethtool flow
spec.
Fixes: eca4205f9ec3 ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a spelling typo in rds.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Randy reported that selecting MPLS_ROUTING without PROC_FS breaks
the build, because since commit c1a9d65954c6 ("mpls: fix af_mpls
dependencies"), MPLS_ROUTING selects PROC_SYSCTL, but Kconfig's select
doesn't recursively handle dependencies.
Change the select into a dependency.
Fixes: c1a9d65954c6 ("mpls: fix af_mpls dependencies")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit a07966447f39 ("geneve: ICMP error lookup handler") I wrongly
assumed buffers from icmp_socket_deliver() would be linear. This is not
the case: icmp_socket_deliver() only guarantees we have 8 bytes of linear
data.
Eric fixed this same issue for fou and fou6 in commits 26fc181e6cac
("fou, fou6: do not assume linear skbs") and 5355ed6388e2 ("fou, fou6:
avoid uninit-value in gue_err() and gue6_err()").
Use pskb_may_pull() instead of checking skb->len, and take into account
the fact we later access the GENEVE header with udp_hdr(), so we also
need to sum skb_transport_header() here.
Reported-by: Guillaume Nault <gnault@redhat.com>
Fixes: a07966447f39 ("geneve: ICMP error lookup handler")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit c3a43b9fec8a ("vxlan: ICMP error lookup handler") I wrongly
assumed buffers from icmp_socket_deliver() would be linear. This is not
the case: icmp_socket_deliver() only guarantees we have 8 bytes of linear
data.
Eric fixed this same issue for fou and fou6 in commits 26fc181e6cac
("fou, fou6: do not assume linear skbs") and 5355ed6388e2 ("fou, fou6:
avoid uninit-value in gue_err() and gue6_err()").
Use pskb_may_pull() instead of checking skb->len, and take into account
the fact we later access the VXLAN header with udp_hdr(), so we also
need to sum skb_transport_header() here.
Reported-by: Guillaume Nault <gnault@redhat.com>
Fixes: c3a43b9fec8a ("vxlan: ICMP error lookup handler")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to create an internal vport, internal_dev_create() is used and
that calls register_netdevice() internally.
If register_netdevice() fails, it calls dev->priv_destructor() to free
private data of netdev. actually, a private data of this is a vport.
Hence internal_dev_create() should not free and use a vport after failure
of register_netdevice().
Test command
ovs-dpctl add-dp bonding_masters
Splat looks like:
[ 1035.667767] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 1035.675958] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 1035.676916] CPU: 1 PID: 1028 Comm: ovs-vswitchd Tainted: G B 5.2.0-rc3+ #240
[ 1035.676916] RIP: 0010:internal_dev_create+0x2e5/0x4e0 [openvswitch]
[ 1035.676916] Code: 48 c1 ea 03 80 3c 02 00 0f 85 9f 01 00 00 4c 8b 23 48 b8 00 00 00 00 00 fc ff df 49 8d bc 24 60 05 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 86 01 00 00 49 8b bc 24 60 05 00 00 e8 e4 68 f4
[ 1035.713720] RSP: 0018:ffff88810dcb7578 EFLAGS: 00010206
[ 1035.713720] RAX: dffffc0000000000 RBX: ffff88810d13fe08 RCX: ffffffff84297704
[ 1035.713720] RDX: 00000000000000ac RSI: 0000000000000000 RDI: 0000000000000560
[ 1035.713720] RBP: 00000000ffffffef R08: fffffbfff0d3b881 R09: fffffbfff0d3b881
[ 1035.713720] R10: 0000000000000001 R11: fffffbfff0d3b880 R12: 0000000000000000
[ 1035.768776] R13: 0000607ee460b900 R14: ffff88810dcb7690 R15: ffff88810dcb7698
[ 1035.777709] FS: 00007f02095fc980(0000) GS:ffff88811b400000(0000) knlGS:0000000000000000
[ 1035.777709] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1035.777709] CR2: 00007ffdf01d2f28 CR3: 0000000108258000 CR4: 00000000001006e0
[ 1035.777709] Call Trace:
[ 1035.777709] ovs_vport_add+0x267/0x4f0 [openvswitch]
[ 1035.777709] new_vport+0x15/0x1e0 [openvswitch]
[ 1035.777709] ovs_vport_cmd_new+0x567/0xd10 [openvswitch]
[ 1035.777709] ? ovs_dp_cmd_dump+0x490/0x490 [openvswitch]
[ 1035.777709] ? __kmalloc+0x131/0x2e0
[ 1035.777709] ? genl_family_rcv_msg+0xa54/0x1030
[ 1035.777709] genl_family_rcv_msg+0x63a/0x1030
[ 1035.777709] ? genl_unregister_family+0x630/0x630
[ 1035.841681] ? debug_show_all_locks+0x2d0/0x2d0
[ ... ]
Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The below patch fixes an incorrect zerocopy refcnt increment when
appending with MSG_MORE to an existing zerocopy udp skb.
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt 1
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt still 1 (bar frags)
But it missed that zerocopy need not be passed at the first send. The
right test whether the uarg is newly allocated and thus has extra
refcnt 1 is not !skb, but !skb_zcopy.
send(.., MSG_MORE); // <no uarg>
send(.., MSG_ZEROCOPY); // refcnt 1
Fixes: 100f6d8e09905 ("net: correct zerocopy refcnt with udp MSG_MORE")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets received at the NFP driver may be redirected to egress of another
netdev (e.g. in the case of OvS internal ports). On the egress path, some
processes, like TC egress hooks, may expect the network header offset
field in the skb to be correctly set. If this is not the case there is
potential for abnormal behaviour and even the triggering of BUG() calls.
Set the skb network header field before the mac header pull when doing a
packet redirect.
Fixes: 27f54b582567 ("nfp: allow fallback packets from non-reprs")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 794200d66273 ("tcp: undo cwnd on Fast Open spurious SYNACK
retransmit") may cause tcp_fastretrans_alert() to warn about pending
retransmission in Open state. This is triggered when the Fast Open
server both sends data and has spurious SYNACK retransmission during
the handshake, and the data packets were lost or reordered.
The root cause is a bit complicated:
(1) Upon receiving SYN-data: a full socket is created with
snd_una = ISN + 1 by tcp_create_openreq_child()
(2) On SYNACK timeout the server/sender enters CA_Loss state.
(3) Upon receiving the final ACK to complete the handshake, sender
does not mark FLAG_SND_UNA_ADVANCED since (1)
Sender then calls tcp_process_loss since state is CA_loss by (2)
(4) tcp_process_loss() does not invoke undo operations but instead
mark REXMIT_LOST to force retransmission
(5) tcp_rcv_synrecv_state_fastopen() calls tcp_try_undo_loss(). It
changes state to CA_Open but has positive tp->retrans_out
(6) Next ACK triggers the WARN_ON in tcp_fastretrans_alert()
The step that goes wrong is (4) where the undo operation should
have been invoked because the ACK successfully acknowledged the
SYN sequence. This fixes that by specifically checking undo
when the SYN-ACK sequence is acknowledged. Then after
tcp_process_loss() the state would be further adjusted based
in tcp_fastretrans_alert() to avoid triggering the warning in (6).
Fixes: 794200d66273 ("tcp: undo cwnd on Fast Open spurious SYNACK retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPLS routing code relies on sysctl to work, so let it select PROC_SYSCTL.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return values for these memory allocations are unchecked,
which may cause an oops if the driver does not handle them after
a failure. Fix by checking the function's return code.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was observed that multicast packets were no longer received after
a device reset. The fix is to resend the current multicast list to
the backing device after recovery.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check driver state before halting it during a reset. If the driver is
not running, do nothing. Otherwise, a request to deactivate a down link
can cause an error and the reset will fail.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you configure a route with multiple labels, e.g.
ip route add 10.10.3.0/24 encap mpls 16/100 via 10.10.2.2 dev ens4
A warning is logged:
kernel: [ 130.561819] netlink: 'ip': attribute type 1 has an invalid
length.
This happens because mpls_iptunnel_policy has set the type of
MPLS_IPTUNNEL_DST to fixed size NLA_U32.
Change it to a minimum size.
nla_get_labels() does the remaining validation.
Fixes: e3e4712ec096 ("mpls: ip tunnel support")
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[Resent to net instead of net-next - may clash with Anders Roxell's patch
series addressing duplicate module names]
Commit 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver")
introduced a new PHY driver drivers/net/phy/asix.c that causes a module
name conflict with a pre-existiting driver (drivers/net/usb/asix.c).
The PHY driver is used by the X-Surf 100 ethernet card driver, and loaded
by that driver via its PHY ID. A rename of the driver looks unproblematic.
Rename PHY driver to ax88796b.c in order to resolve name conflict.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before taking a refcount, make sure the object is not already
scheduled for deletion.
Same fix is needed in ipv6_flowlabel_opt()
Fixes: 18367681a10b ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix an uninitialized variable:
CC net/ipv4/fib_semantics.o
net/ipv4/fib_semantics.c: In function 'fib_check_nh_v4_gw':
net/ipv4/fib_semantics.c:1027:12: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (!tbl || err) {
^~
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stacked devices like bond interface may have a VLAN device on top of
them. Detect lag state correctly under this condition, and return the
correct routed net device, according to it the encap header is built.
Fixes: e32ee6c78efa ("net/mlx5e: Support tunnel encap over tagged Ethernet")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After introducing dedicated uplink representor, the netdev instance
set over the esw manager vport (PF) became no longer in use, so it was
removed in the cited commit once we're on switchdev mode.
However, the mlx5e_detach function was not updated accordingly, and it
still tries to detach a non-existing netdev, causing a kernel crash.
This patch fixes this issue.
Fixes: aec002f6f82c ("net/mlx5e: Uninstantiate esw manager vport netdev on switchdev mode")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The cited commit changed the initialization placement of the eswitch
attributes so it is done prior to parse tc actions function call,
including among others the in_rep and in_mdev fields which are mistakenly
reassigned inside the parse actions function.
This breaks the source port matching criteria of the peer redirect rule.
Fix by removing the now redundant reassignment of the already initialized
fields.
Fixes: 988ab9c7363a ("net/mlx5e: Introduce mlx5e_flow_esw_attr_init() helper")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The TX queue index returned by the fallback function ranges
between [0,NUM CHANNELS - 1] if QoS isn't set and
[0, (NUM CHANNELS)*(NUM TCs) -1] otherwise.
Our HW uses different TC mapping than the fallback function
(which is denoted as 'up', user priority) so we only need to extract
a channel number out of the returned value.
Since (NUM CHANNELS)*(NUM TCs) is a relatively small number, using
reciprocal scale almost always returns zero.
We instead access the 'txq2sq' table to extract the sq (and with it the
channel number) associated with the tx queue, thus getting
a more evenly distributed channel number.
Perf:
Rx/Tx side with Intel(R) Xeon(R) Silver 4108 CPU @ 1.80GHz and ConnectX-5.
Used 'iperf' UDP traffic, 10 threads, and priority 5.
Before: 0.566Mpps
After: 2.37Mpps
As expected, releasing the existing bottleneck of steering all traffic
to TX queue zero significantly improves transmission rates.
Fixes: 7ccdd0841b30 ("net/mlx5e: Fix select queue callback")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After we have a dedicated uplink representor, the new netdev ops
doesn't support ndo_set_feature. Because of that, we can't change
some features, eg. rxvlan. Now add it back.
In this patch, I also do a cleanup for the features flag handling,
eg. remove duplicate NETIF_F_HW_TC flag setting.
Fixes: aec002f6f82c ("net/mlx5e: Uninstantiate esw manager vport netdev on switchdev mode")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Prior to reloading a device we must first verify that it was not already
removed. Otherwise, the attempt to remove the device will do nothing, and
in that case we will end up proceeding with adding an new device that no
one was expecting to remove, leaving behind used resources such as EQs that
causes a failure to destroy comp EQs and syndrome (0x30f433).
Fix that by making sure that we try to remove and add a device (based on a
protocol) only if the device is already added.
Fixes: c5447c70594b ("net/mlx5: E-Switch, Reload IB interface when switching devlink modes")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add missing entries for create/destroy UCTX and UMEM commands.
This could get us wrong "unknown FW command" error in flows
where we unbind the device or reset the driver.
Also the translation of these commands from opcodes to string
was missing.
Fixes: 6e3722baac04 ("IB/mlx5: Use the correct commands for UMEM and UCTX allocation")
Signed-off-by: Edward Srouji <edwards@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
CAN supports software tx timestamps as of the below commit. Purge
any queued timestamp packets on socket destroy.
Fixes: 51f31cabe3ce ("ip: support for TX timestamps on UDP and RAW sockets")
Reported-by: syzbot+a90604060cb40f5bdd16@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently the following message is observed when the flexcan
driver is probed:
flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=23)
The reason for printing 'ptrval' is explained at
Documentation/core-api/printk-formats.rst:
"Pointers printed without a specifier extension (i.e unadorned %p) are
hashed to prevent leaking information about the kernel memory layout. This
has the added benefit of providing a unique identifier. On 64-bit machines
the first 32 bits are zeroed. The kernel will print ``(ptrval)`` until it
gathers enough entropy."
Instead of passing %pK, which can print the correct address, simply
remove the entire message as it is not really that useful.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch add error path for can_init() to avoid possible crash if some
error occurs.
Fixes: 0d66548a10cb ("[CAN]: Add PF_CAN core module")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During frame reception while the MCAN is in Error Passive state and the
Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen
that MCAN_IR.MRAF is set although there was no Message RAM access
failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is
generated.
Work around:
The Message RAM Access Failure interrupt routine needs to check whether
MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.
In this case, reset MCAN_IR.MRAF. No further action is required.
This affects versions older than 3.2.0
Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf
chapter 6.2
Reproducibility: If 2 devices with m_can are connected back to back,
configuring different bitrate on them will lead to interrupt storm on
the receiving side, with error "Message RAM access failure occurred".
Another way is to have a bad hardware connection. Bad wire connection
can lead to this issue as well.
This patch fixes the issue according to provided workaround.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch adds support for the mcp25625 to the existing mcp251x driver.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch add the mcp25625 to the device tree bindings documentation.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit 9e5f1b273e6a ("can: xilinx_can: add support for Xilinx CAN FD
core") added a new can_bittiming_const structure for CAN FD cores that
support larger values for tseg1, tseg2, and sjw than previous Xilinx CAN
cores, but the commit did not actually take that into use.
Fix that.
Tested with CAN FD core on a ZynqMP board.
Fixes: 9e5f1b273e6a ("can: xilinx_can: add support for Xilinx CAN FD core")
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Current we can meet timeout issue when setting a small bitrate like
10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock =
30MHZ):
| root@imx6ul7d:~# ip link set can0 up type can bitrate 10000
A link change request failed with some changes committed already.
Interface can0 may have been left with an inconsistent configuration,
please check.
| RTNETLINK answers: Connection timed out
It is caused by calling of flexcan_chip_unfreeze() timeout.
Originally the code is using usleep_range(10, 20) for unfreeze
operation, but the patch (8badd65 can: flexcan: avoid calling
usleep_range from interrupt context) changed it into udelay(10) which is
only a half delay of before, there're also some other delay changes.
After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue.
Meanwhile, Rasmus Villemoes reported that even with a timeout of 100,
flexcan_probe() fails on the MPC8309, which requires a value of at least
140 to work reliably. 250 works for everyone.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This seems to have slipped in by accident when sorting the entries.
Fixes: ffbdd9172ee2f53020f763574b4cdad8d9760a4f
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add cgroup/recvmsg{4,6} to test_section_names as well. Test run output:
# ./test_section_names
libbpf: failed to guess program type based on ELF section name 'InvAliD'
libbpf: supported section(type) names are: [...]
libbpf: failed to guess attach type based on ELF section name 'InvAliD'
libbpf: attachable section(type) names are: [...]
libbpf: failed to guess program type based on ELF section name 'cgroup'
libbpf: supported section(type) names are: [...]
libbpf: failed to guess attach type based on ELF section name 'cgroup'
libbpf: attachable section(type) names are: [...]
Summary: 38 PASSED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Extend test_sock_addr for recvmsg test cases, bigger parts of the
sendmsg code can be reused for this. Below are the strace view of
the recvmsg rewrites; the sendmsg side does not have a BPF prog
connected to it for the context of this test:
IPv4 test case:
[pid 4846] bpf(BPF_PROG_ATTACH, {target_fd=3, attach_bpf_fd=4, attach_type=0x13 /* BPF_??? */, attach_flags=BPF_F_ALLOW_OVERRIDE}, 112) = 0
[pid 4846] socket(AF_INET, SOCK_DGRAM, IPPROTO_IP) = 5
[pid 4846] bind(5, {sa_family=AF_INET, sin_port=htons(4444), sin_addr=inet_addr("127.0.0.1")}, 128) = 0
[pid 4846] socket(AF_INET, SOCK_DGRAM, IPPROTO_IP) = 6
[pid 4846] sendmsg(6, {msg_name={sa_family=AF_INET, sin_port=htons(4444), sin_addr=inet_addr("127.0.0.1")}, msg_namelen=128, msg_iov=[{iov_base="a", iov_len=1}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 1
[pid 4846] select(6, [5], NULL, NULL, {tv_sec=2, tv_usec=0}) = 1 (in [5], left {tv_sec=1, tv_usec=999995})
[pid 4846] recvmsg(5, {msg_name={sa_family=AF_INET, sin_port=htons(4040), sin_addr=inet_addr("192.168.1.254")}, msg_namelen=128->16, msg_iov=[{iov_base="a", iov_len=64}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 1
[pid 4846] close(6) = 0
[pid 4846] close(5) = 0
[pid 4846] bpf(BPF_PROG_DETACH, {target_fd=3, attach_type=0x13 /* BPF_??? */}, 112) = 0
IPv6 test case:
[pid 4846] bpf(BPF_PROG_ATTACH, {target_fd=3, attach_bpf_fd=4, attach_type=0x14 /* BPF_??? */, attach_flags=BPF_F_ALLOW_OVERRIDE}, 112) = 0
[pid 4846] socket(AF_INET6, SOCK_DGRAM, IPPROTO_IP) = 5
[pid 4846] bind(5, {sa_family=AF_INET6, sin6_port=htons(6666), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=htonl(0), sin6_scope_id=0}, 128) = 0
[pid 4846] socket(AF_INET6, SOCK_DGRAM, IPPROTO_IP) = 6
[pid 4846] sendmsg(6, {msg_name={sa_family=AF_INET6, sin6_port=htons(6666), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=htonl(0), sin6_scope_id=0}, msg_namelen=128, msg_iov=[{iov_base="a", iov_len=1}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 1
[pid 4846] select(6, [5], NULL, NULL, {tv_sec=2, tv_usec=0}) = 1 (in [5], left {tv_sec=1, tv_usec=999996})
[pid 4846] recvmsg(5, {msg_name={sa_family=AF_INET6, sin6_port=htons(6060), inet_pton(AF_INET6, "face:b00c:1234:5678::abcd", &sin6_addr), sin6_flowinfo=htonl(0), sin6_scope_id=0}, msg_namelen=128->28, msg_iov=[{iov_base="a", iov_len=64}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 1
[pid 4846] close(6) = 0
[pid 4846] close(5) = 0
[pid 4846] bpf(BPF_PROG_DETACH, {target_fd=3, attach_type=0x14 /* BPF_??? */}, 112) = 0
test_sock_addr run w/o strace view:
# ./test_sock_addr.sh
[...]
Test case: recvmsg4: return code ok .. [PASS]
Test case: recvmsg4: return code !ok .. [PASS]
Test case: recvmsg6: return code ok .. [PASS]
Test case: recvmsg6: return code !ok .. [PASS]
Test case: recvmsg4: rewrite IP & port (asm) .. [PASS]
Test case: recvmsg6: rewrite IP & port (asm) .. [PASS]
[...]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Trivial patch to bpftool in order to complete enabling attaching programs
to BPF_CGROUP_UDP{4,6}_RECVMSG.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Another trivial patch to libbpf in order to enable identifying and
attaching programs to BPF_CGROUP_UDP{4,6}_RECVMSG by section name.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Sync BPF uapi header in order to pull in BPF_CGROUP_UDP{4,6}_RECVMSG
attach types. This is done and preferred as an extra patch in order
to ease sync of libbpf.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
