| Commit message (Collapse) | Author | Files | Lines |
|---|
|
During testing it was noticed that the link is not properly restored
after the domain exits sleep if the link configured bits are set before
lane bonding is enabled. The USB4 spec does not say in which order these
need to be set but setting link configured afterwards makes the link
restoration work so we do that instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Some early stage USB4 devices do not like that any of the enumerating
router config space fields (ROUTER_CS_1 - ROUTER_CS_4) are written after
the initial enumeration for example when entering sleep states. The
default timeout by the USB4 spec is 10 ms which should be fine for the
driver to handle.
For this reason do not change the notification timeout from the default
10 ms for USB4 routers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The TMU will be reset after router exits sleep so in order to
re-configure it upon resume make sure the structure is initialized again
based on the current hardware state.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
DP tunnels do not need the same kind of treatment as others because they
are created based on hot-plug events on DP adapter ports, and the
display stack does not need the tunnels to be enabled when resuming from
suspend. Also Tiger Lake Thunderbolt controller sends unplug event on D3
exit so this avoids that as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
First generation routers may need the reset command upon resume but it
is not supported by newer generations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The function already logs an error if it fails so get rid of the
duplication.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 spec says that NFC buffers field is not used for protocol adapters,
only for lane adapters so make tb_port_add_nfc_credits() skip non-lane
adapters in order to follow the spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In Tiger Lake the Firmware CM is always enabled (so bit 0 is always set)
but it may be in "pass through" mode which means it requires Software CM
instead. This can be determined by checking bit 31 instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When Software CM is running it should not send any NHI mailbox command
during PM flows. Only force power bit needs to be set and cleared so
change Tiger Lake (well and Ice Lake) nhi_ops to take this into account.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently the Ice Lake and Tiger Lake NHI (host controller) LC (link
controller) mailbox command processing checks for the completion of
command every 100 msecs. These controllers are found to complete this in
the order of 1 ms or so. Since this delay is in suspend path, surplus
delay is effectively affecting runtime PM suspend flows.
Optimize this so that we do the wait for 1 ms after reading the mailbox
register. This should make Ice Lake and Tiger Lake runtime suspend take
less time to complete.
Reported-by: Dana Alkattan <dana.alkattan@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently the "Force Power" logic uses 10 retries, each with a delay of
250 ms. Thunderbolt controllers in Ice Lake and Tiger Lake platforms are
found to complete this in the order of 3 ms or so. Since this delay
is in resume path, surplus delay is effectively affecting runtime PM
resume flows.
Decrease the granularity of the delay to 3 ms and increase the number of
retries so we wait maximum of ~1 s which is the recommended timeout.
This should make runtime resume a bit faster.
Reported-by: Dana Alkattan <dana.alkattan@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Doesn't really matter for an individual driver, but it may
get coppied to lots more. I consider it's a little tidy up.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
|
|
Most of the CPU mask operations behave the same way, but for_each_cpu() and
it's variants ignore the cpumask argument and claim that CPU0 is always in
the mask. This is historical, inconsistent and annoying behaviour.
The matrix allocator uses for_each_cpu() and can be called on UP with an
empty cpumask. The calling code does not expect that this succeeds but
until commit e027fffff799 ("x86/irq: Unbreak interrupt affinity setting")
this went unnoticed. That commit added a WARN_ON() to catch cases which
move an interrupt from one vector to another on the same CPU. The warning
triggers on UP.
Add a check for the cpumask being empty to prevent this.
Fixes: 2f75d9e1c905 ("genirq: Implement bitmap matrix allocator")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
Commit ef91bb196b0d ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.
That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical. There were no
high bits to mask off to begin with.
But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.
Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all. Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.
This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.
This patch at least makes it not fail the build any more, and makes the
logic superficially sane. Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I keep getting sparse warnings in crypto such as:
CHECK drivers/crypto/ccree/cc_hash.c
drivers/crypto/ccree/cc_hash.c:49:9: warning: cast truncates bits from constant value (47b5481dbefa4fa4 becomes befa4fa4)
drivers/crypto/ccree/cc_hash.c:49:26: warning: cast truncates bits from constant value (db0c2e0d64f98fa7 becomes 64f98fa7)
[.. many more ..]
This patch removes the warning by adding a mask to keep sparse
happy.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For SMB1, the DFS flag should be checked against tcon->Flags rather
than tcon->share_flags. While at it, add an is_tcon_dfs() helper to
check for DFS capability in a more generic way.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Shyam Prasad N <nspmangalore@gmail.com>
|
|
AT instructions do a translation table walk and return the result, or
the fault in PAR_EL1. KVM uses these to find the IPA when the value is
not provided by the CPU in HPFAR_EL1.
If a translation table walk causes an external abort it is taken as an
exception, even if it was due to an AT instruction. (DDI0487F.a's D5.2.11
"Synchronous faults generated by address translation instructions")
While we previously made KVM resilient to exceptions taken due to AT
instructions, the device access causes mismatched attributes, and may
occur speculatively. Prevent this, by forbidding a walk through memory
described as device at stage2. Now such AT instructions will report a
stage2 fault.
Such a fault will cause KVM to restart the guest. If the AT instructions
always walk the page tables, but guest execution uses the translation cached
in the TLB, the guest can't make forward progress until the TLB entry is
evicted. This isn't a problem, as since commit 5dcd0fdbb492 ("KVM: arm64:
Defer guest entry when an asynchronous exception is pending"), KVM will
return to the host to process IRQs allowing the rest of the system to keep
running.
Cc: stable@vger.kernel.org # <v5.3: 5dcd0fdbb492 ("KVM: arm64: Defer guest entry when an asynchronous exception is pending")
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
KVM doesn't expect any synchronous exceptions when executing, any such
exception leads to a panic(). AT instructions access the guest page
tables, and can cause a synchronous external abort to be taken.
The arm-arm is unclear on what should happen if the guest has configured
the hardware update of the access-flag, and a memory type in TCR_EL1 that
does not support atomic operations. B2.2.6 "Possible implementation
restrictions on using atomic instructions" from DDI0487F.a lists
synchronous external abort as a possible behaviour of atomic instructions
that target memory that isn't writeback cacheable, but the page table
walker may behave differently.
Make KVM robust to synchronous exceptions caused by AT instructions.
Add a get_user() style helper for AT instructions that returns -EFAULT
if an exception was generated.
While KVM's version of the exception table mixes synchronous and
asynchronous exceptions, only one of these can occur at each location.
Re-enter the guest when the AT instructions take an exception on the
assumption the guest will take the same exception. This isn't guaranteed
to make forward progress, as the AT instructions may always walk the page
tables, but guest execution may use the translation cached in the TLB.
This isn't a problem, as since commit 5dcd0fdbb492 ("KVM: arm64: Defer guest
entry when an asynchronous exception is pending"), KVM will return to the
host to process IRQs allowing the rest of the system to keep running.
Cc: stable@vger.kernel.org # <v5.3: 5dcd0fdbb492 ("KVM: arm64: Defer guest entry when an asynchronous exception is pending")
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
KVM has a one instruction window where it will allow an SError exception
to be consumed by the hypervisor without treating it as a hypervisor bug.
This is used to consume asynchronous external abort that were caused by
the guest.
As we are about to add another location that survives unexpected exceptions,
generalise this code to make it behave like the host's extable.
KVM's version has to be mapped to EL2 to be accessible on nVHE systems.
The SError vaxorcism code is a one instruction window, so has two entries
in the extable. Because the KVM code is copied for VHE and nVHE, we end up
with four entries, half of which correspond with code that isn't mapped.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
vdso32 should only be installed if CONFIG_COMPAT_VDSO is enabled,
since it's not even supposed to be compiled otherwise, and arm64
builds without a 32bit crosscompiler will fail.
Fixes: 8d75785a8142 ("ARM64: vdso32: Install vdso32 from vdso_install")
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Cc: stable@vger.kernel.org [5.4+]
Link: https://lore.kernel.org/r/20200827234012.19757-1-fllinden@amazon.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit 7c78f67e9bd9 ("arm64: enable tlbi range instructions") breaks
LLVM's integrated assembler, because -Wa,-march is only passed to
external assemblers and therefore, the new instructions are not enabled
when IAS is used.
This change adds a common architecture version preamble, which can be
used in inline assembly blocks that contain instructions that require
a newer architecture version, and uses it to fix __TLBI_0 and __TLBI_1
with ARM64_TLB_RANGE.
Fixes: 7c78f67e9bd9 ("arm64: enable tlbi range instructions")
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1106
Link: https://lore.kernel.org/r/20200827203608.1225689-1-samitolvanen@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit e49aa9a9bd22 ("mfd: core: Make a best effort attempt to match
devices with the correct of_nodes") changed the semantics for disabled
devices in mfd_add_device(). Instead of silently ignoring a disabled
child device, an error was returned. On receipt of the error
mfd_add_devices() the precedes to remove *all* child devices and
returns an all-failed error to the caller, which will inevitably fail
the parent device as well.
This patch reverts back to the old semantics and ignores child devices
which are disabled in Device Tree.
Fixes: e49aa9a9bd22 ("mfd: core: Make a best effort attempt to match devices with the correct of_nodes")
Reported-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 3b5408b98e4d ("md/raid5: support config stripe_size by sysfs
entry") make stripe_size as a configurable value. It just requires
stripe_size as multiple of 4KB.
In fact, we should make sure stripe_size as power of two. Otherwise,
stripe_shift which is the result of ilog2 can not represent the real
stripe_size. Then, stripe_hash() and stripe_hash_locks_hash() may
get unexpected value.
Fixes: 3b5408b98e4d ("md/raid5: support config stripe_size by sysfs entry")
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
|
|
low_sleep_handler() can't restore the context from virtual
stack because the stack can hardly be accessed with MMU OFF.
For now, disable VMAP stack when CONFIG_ADB_PMU is selected.
Fixes: cd08f109e262 ("powerpc/32s: Enable CONFIG_VMAP_STACK")
Cc: stable@vger.kernel.org # v5.6+
Reported-by: Giuseppe Sacco <giuseppe@sguazz.it>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ec96c15bfa1a7415ab604ee1c98cd45779c08be0.1598553015.git.christophe.leroy@csgroup.eu
|
|
These events happen inline from submission, so there's no need to
bounce them through the original task. Just set them up for retry
and issue retry directly instead of going over task_work.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This normally isn't hit, as polling is mostly done on NVMe with deep
queue depths. But if we do run into request starvation, we need to
ensure that retries are properly serialized.
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fallthrough annotations for consecutive default and case labels
are not necessary.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Fix identation issues.
Fixes: 5e9c85d98337 ("[media] dib8096: enhancement")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
The GSC registers report temperature in decidegrees celcius so we
need to scale it to represent the hwmon sysfs API of millidegrees.
Cc: stable@vger.kernel.org
Fixes: 3bce5377ef66 ("hwmon: Add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://lore.kernel.org/r/1598548824-16898-1-git-send-email-tharvey@gateworks.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The fall through annotation comes after a return statement so it's not
reachable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
After
b9cae27728d1 ("EDAC/ghes: Scan the system once on driver init")
and with CONFIG_DEBUG_TEST_DRIVER_REMOVE enabled, ghes_hw.dimms becomes
a NULL pointer after the second ->probe() (aka ghes_edac_register())
which the config option causes to be called.
This happens because the static variable which holds down whether
the system has been scanned already, doesn't get reset in
ghes_edac_unregister(). Then, on the second probe, ghes_scan_system()
doesn't get to enumerate the DIMMs, leading to ghes_hw.dimms remaining
NULL.
Clear the variable and rename it to something more descriptive so that a
second probe succeeds.
[ bp: Rewrite commit message. ]
Fixes: b9cae27728d1 ("EDAC/ghes: Scan the system once on driver init")
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200827140450.1620-1-shiju.jose@huawei.com
|
|
The iwd daemon uses libell which sets up the skcipher operation with
two separate control messages. As the first control message is sent
without MSG_MORE, it is interpreted as an empty request.
While libell should be fixed to use MSG_MORE where appropriate, this
patch works around the bug in the kernel so that existing binaries
continue to work.
We will print a warning however.
A separate issue is that the new kernel code no longer allows the
control message to be sent twice within the same request. This
restriction is obviously incompatible with what iwd was doing (first
setting an IV and then sending the real control message). This
patch changes the kernel so that this is explicitly allowed.
Reported-by: Caleb Jorden <caljorden@hotmail.com>
Fixes: f3c802a1f300 ("crypto: algif_aead - Only wake up when...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The relation can't be invalid here, so if it turns out to be invalid,
just WARN_ON_ONCE() and return 0.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
"cpufreq_driver" is guaranteed to be valid here, no need to check it
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpuidle stop state implementation has minor optimizations for P10
where hardware preserves more SPR registers compared to P9. The
current P9 driver works for P10, although does few extra
save-restores. P9 driver can provide the required power management
features like SMT thread folding and core level power savings on a P10
platform.
Until the P10 stop driver is available, revert the commit which allows
for only P9 systems to utilize cpuidle and blocks all idle stop states
for P10. CPU idle states are enabled and tested on the P10 platform
with this fix.
This reverts commit 8747bf36f312356f8a295a0c39ff092d65ce75ae.
Fixes: 8747bf36f312 ("powerpc/powernv/idle: Replace CPU feature check with PVR check")
Signed-off-by: Pratik Rajesh Sampat <psampat@linux.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200826082918.89306-1-psampat@linux.ibm.com
|
|
IMC trace-mode uses MSR[HV/PR] bits to set the cpumode for the
instruction pointer captured in each sample. The bits are fetched from
the third double word of the trace record. Reading third double word
from IMC trace record should use be64_to_cpu() along with READ_ONCE
inorder to fetch correct MSR[HV/PR] bits. Patch addresses this change.
Currently we are using PERF_RECORD_MISC_HYPERVISOR as cpumode if MSR
HV is 1 and PR is 0 which means the address is from host counter. But
using PERF_RECORD_MISC_HYPERVISOR for host counter data will fail to
resolve the address -> symbol during "perf report" because perf tools
side uses PERF_RECORD_MISC_KERNEL to represent the host counter data.
Therefore, fix the trace imc sample data to use
PERF_RECORD_MISC_KERNEL as cpumode for host kernel information.
Fixes: 77ca3951cc37 ("powerpc/perf: Add kernel support for new MSR[HV PR] bits in trace-imc")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1598424029-1662-1-git-send-email-atrajeev@linux.vnet.ibm.com
|
|
The bhrb_filter_map ("The Branch History Rolling Buffer") callback is
only defined in raw CPUs' power_pmu structs. The "architected" CPUs
use generic_compat_pmu, which does not have this callback, and crashes
occur if a user tries to enable branch stack for an event.
This add a NULL pointer check for bhrb_filter_map() which behaves as
if the callback returned an error.
This does not add the same check for config_bhrb() as the only caller
checks for cpuhw->bhrb_users which remains zero if bhrb_filter_map==0.
Fixes: be80e758d0c2 ("powerpc/perf: Add generic compat mode pmu driver")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200602025612.62707-1-aik@ozlabs.ru
|
|
The recent commit 01eb01877f33 ("powerpc/64s: Fix restore_math
unnecessarily changing MSR") changed some of the handling of floating
point/vector restore.
In particular it caused current->thread.fpexc_mode to be copied into
the current MSR (via msr_check_and_set()), rather than just into
regs->msr (which is moved into MSR on return to userspace).
This can lead to a crash in the kernel if we take a floating point
exception when restoring FPSCR:
Oops: Exception in kernel mode, sig: 8 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in:
CPU: 3 PID: 101213 Comm: ld64.so.2 Not tainted 5.9.0-rc1-00098-g18445bf405cb-dirty #9
NIP: c00000000000fbb4 LR: c00000000001a7ac CTR: c000000000183570
REGS: c0000016b7cfb3b0 TRAP: 0700 Not tainted (5.9.0-rc1-00098-g18445bf405cb-dirty)
MSR: 900000000290b933 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 44002444 XER: 00000000
CFAR: c00000000001a7a8 IRQMASK: 1
GPR00: c00000000001ae40 c0000016b7cfb640 c0000000011b7f00 c000001542a0f740
GPR04: c000001542a0f720 c000001542a0eb00 0000000000000900 c000001542a0eb00
GPR08: 000000000000000a 0000000000002000 9000000000009033 0000000000000000
GPR12: 0000000000004000 c0000017ffffd900 0000000000000001 c000000000df5a58
GPR16: c000000000e19c18 c0000000010e1123 0000000000000001 c000000000e1a638
GPR20: 0000000000000000 c0000000044b1d00 0000000000000000 c000001542a0f2a0
GPR24: 00000016c7fe0000 c000001542a0f720 c000000001c93da0 c000000000fe5f28
GPR28: c000001542a0f720 0000000000800000 c0000016b7cfbe90 0000000002802900
NIP load_fp_state+0x4/0x214
LR restore_math+0x17c/0x1f0
Call Trace:
0xc0000016b7cfb680 (unreliable)
__switch_to+0x330/0x460
__schedule+0x318/0x920
schedule+0x74/0x140
schedule_timeout+0x318/0x3f0
wait_for_completion+0xc8/0x210
call_usermodehelper_exec+0x234/0x280
do_coredump+0xedc/0x13c0
get_signal+0x1d4/0xbe0
do_notify_resume+0x1a0/0x490
interrupt_exit_user_prepare+0x1c4/0x230
interrupt_return+0x14/0x1c0
Instruction dump:
ebe10168 e88101a0 7c8ff120 382101e0 e8010010 7c0803a6 4e800020 790605c4
782905c4 7c0008a8 7c0008a8 c8030200 <fffe058e> 48000088 c8030000 c8230010
Fix it by only loading the fpexc_mode value into regs->msr.
Also add a comment to explain that although VSX is subject to the
value of fpexc_mode, we don't have to handle that separately because
we only allow VSX to be enabled if FP is also enabled.
Fixes: 01eb01877f33 ("powerpc/64s: Fix restore_math unnecessarily changing MSR")
Reported-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Link: https://lore.kernel.org/r/20200825093424.3967813-1-mpe@ellerman.id.au
|
|
Kernel entry sets PPR to HMT_MEDIUM by convention. The scv entry
path missed this.
Fixes: 7fa95f9adaee ("powerpc/64s: system call support for scv/rfscv instructions")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200825075309.224184-1-npiggin@gmail.com
|
|
Fix malformed table warning in powerpc/syscall64-abi.rst by making
two tables and moving the headings.
Documentation/powerpc/syscall64-abi.rst:53: WARNING: Malformed table.
Text in column margin in table line 2.
=========== ============= ========================================
--- For the sc instruction, differences with the ELF ABI ---
r0 Volatile (System call number.)
r3 Volatile (Parameter 1, and return value.)
r4-r8 Volatile (Parameters 2-6.)
cr0 Volatile (cr0.SO is the return error condition.)
cr1, cr5-7 Nonvolatile
lr Nonvolatile
--- For the scv 0 instruction, differences with the ELF ABI ---
r0 Volatile (System call number.)
r3 Volatile (Parameter 1, and return value.)
r4-r8 Volatile (Parameters 2-6.)
=========== ============= ========================================
Fixes: 7fa95f9adaee ("powerpc/64s: system call support for scv/rfscv instructions")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/e06de4d3-a36f-2745-9775-467e125436cc@infradead.org
|
|
The build is currently broken, if COMPILE_TEST=y and PPC_PMAC=n:
linux/drivers/video/fbdev/controlfb.c: In function ‘control_set_hardware’:
linux/drivers/video/fbdev/controlfb.c:276:2: error: implicit declaration of function ‘btext_update_display’
276 | btext_update_display(p->frame_buffer_phys + CTRLFB_OFF,
| ^~~~~~~~~~~~~~~~~~~~
Fix it by including btext.h whenever CONFIG_BOOTX_TEXT is enabled.
Fixes: a07a63b0e24d ("video: fbdev: controlfb: add COMPILE_TEST support")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://lore.kernel.org/r/20200821104910.3363818-1-mpe@ellerman.id.au
|
|
Several people reported that 5.8 broke the interrupt affinity setting
mechanism.
The consolidation of the entry code reused the regular exception entry code
for device interrupts and changed the way how the vector number is conveyed
from ptregs->orig_ax to a function argument.
The low level entry uses the hardware error code slot to push the vector
number onto the stack which is retrieved from there into a function
argument and the slot on stack is set to -1.
The reason for setting it to -1 is that the error code slot is at the
position where pt_regs::orig_ax is. A positive value in pt_regs::orig_ax
indicates that the entry came via a syscall. If it's not set to a negative
value then a signal delivery on return to userspace would try to restart a
syscall. But there are other places which rely on pt_regs::orig_ax being a
valid indicator for syscall entry.
But setting pt_regs::orig_ax to -1 has a nasty side effect vs. the
interrupt affinity setting mechanism, which was overlooked when this change
was made.
Moving interrupts on x86 happens in several steps. A new vector on a
different CPU is allocated and the relevant interrupt source is
reprogrammed to that. But that's racy and there might be an interrupt
already in flight to the old vector. So the old vector is preserved until
the first interrupt arrives on the new vector and the new target CPU. Once
that happens the old vector is cleaned up, but this cleanup still depends
on the vector number being stored in pt_regs::orig_ax, which is now -1.
That -1 makes the check for cleanup: pt_regs::orig_ax == new_vector
always false. As a consequence the interrupt is moved once, but then it
cannot be moved anymore because the cleanup of the old vector never
happens.
There would be several ways to convey the vector information to that place
in the guts of the interrupt handling, but on deeper inspection it turned
out that this check is pointless and a leftover from the old affinity model
of X86 which supported multi-CPU affinities. Under this model it was
possible that an interrupt had an old and a new vector on the same CPU, so
the vector match was required.
Under the new model the effective affinity of an interrupt is always a
single CPU from the requested affinity mask. If the affinity mask changes
then either the interrupt stays on the CPU and on the same vector when that
CPU is still in the new affinity mask or it is moved to a different CPU, but
it is never moved to a different vector on the same CPU.
Ergo the cleanup check for the matching vector number is not required and
can be removed which makes the dependency on pt_regs:orig_ax go away.
The remaining check for new_cpu == smp_processsor_id() is completely
sufficient. If it matches then the interrupt was successfully migrated and
the cleanup can proceed.
For paranoia sake add a warning into the vector assignment code to
validate that the assumption of never moving to a different vector on
the same CPU holds.
Fixes: 633260fa143 ("x86/irq: Convey vector as argument and not in ptregs")
Reported-by: Alex bykov <alex.bykov@scylladb.com>
Reported-by: Avi Kivity <avi@scylladb.com>
Reported-by: Alexander Graf <graf@amazon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Graf <graf@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87wo1ltaxz.fsf@nanos.tec.linutronix.de
|
|
There is a race when taking a CPU offline. Current code looks like this:
native_cpu_disable()
{
...
apic_soft_disable();
/*
* Any existing set bits for pending interrupt to
* this CPU are preserved and will be sent via IPI
* to another CPU by fixup_irqs().
*/
cpu_disable_common();
{
....
/*
* Race window happens here. Once local APIC has been
* disabled any new interrupts from the device to
* the old CPU are lost
*/
fixup_irqs(); // Too late to capture anything in IRR.
...
}
}
The fix is to disable the APIC *after* cpu_disable_common().
Testing was done with a USB NIC that provided a source of frequent
interrupts. A script migrated interrupts to a specific CPU and
then took that CPU offline.
Fixes: 60dcaad5736f ("x86/hotplug: Silence APIC and NMI when CPU is dead")
Reported-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/875zdarr4h.fsf@nanos.tec.linutronix.de/
Link: https://lore.kernel.org/r/1598501530-45821-1-git-send-email-ashok.raj@intel.com
|
|
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com>
Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Fixes: 62194244cf87 ("USB: Add Samsung Exynos OHCI diver")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Inadvertently the commit b1cd1b65afba ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4f2 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "page" pointer can be used with out being initialized.
Fixes: d7e673ec2c8e ("dma-pool: Only allocate from CMA when in same memory zone")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
