| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit 103544d86976 ("ACPI,PCI,IRQ: reduce resource requirements")
replaced the addition of PIRQ_PENALTY_PCI_USING in acpi_pci_link_allocate()
with an addition in acpi_irq_pci_sharing_penalty(), but f7eca374f000
("ACPI,PCI,IRQ: separate ISA penalty calculation") removed the use
of acpi_irq_pci_sharing_penalty() for ISA IRQs.
Therefore, PIRQ_PENALTY_PCI_USING is missing from ISA IRQs used by
interrupt links. Include that penalty by adding it in the
acpi_pci_link_allocate() path.
Fixes: f7eca374f000 (ACPI,PCI,IRQ: separate ISA penalty calculation)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Ondrej reported that IRQs stopped working in v4.7 on several
platforms. A typical scenario, from Ondrej's VT82C694X/694X, is:
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: No IRQ available for PCI Interrupt Link [LNKA]
8139too 0000:00:0f.0: PCI INT A: no GSI
We're using PIC routing, so acpi_irq_balance == 0, and LNKA is already
active at IRQ 11. In that case, acpi_pci_link_allocate() only tries
to use the active IRQ (IRQ 11) which also happens to be the SCI.
We should penalize the SCI by PIRQ_PENALTY_PCI_USING, but
irq_get_trigger_type(11) returns something other than
IRQ_TYPE_LEVEL_LOW, so we penalize it by PIRQ_PENALTY_ISA_ALWAYS
instead, which makes acpi_pci_link_allocate() assume the IRQ isn't
available and give up.
Add acpi_penalize_sci_irq() so platforms can tell us the SCI IRQ,
trigger, and polarity directly and we don't have to depend on
irq_get_trigger_type().
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Link: http://lkml.kernel.org/r/201609251512.05657.linux@rainbow-software.org
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We do not want to store the SCI penalty in the acpi_isa_irq_penalty[]
table because acpi_isa_irq_penalty[] only holds ISA IRQ penalties and
there's no guarantee that the SCI is an ISA IRQ. We add in the SCI
penalty as a special case in acpi_irq_get_penalty().
But if we called acpi_penalize_isa_irq() or acpi_irq_penalty_update()
for an SCI that happened to be an ISA IRQ, they stored the SCI
penalty (part of the acpi_irq_get_penalty() return value) in
acpi_isa_irq_penalty[]. Subsequent calls to acpi_irq_get_penalty()
returned a penalty that included *two* SCI penalties.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since commit 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
the penalty values are calculated on the fly rather than at boot time.
This works fine for PCI interrupts but not so well for ISA interrupts.
The information on whether or not an ISA interrupt is in use is not
available to the pci_link.c code directly. That information is
obtained from the outside via acpi_penalize_isa_irq(). [If its
"active" argument is true, then the IRQ is in use by ISA.]
Since the current code relies on PCI Link objects for determination
of penalties, we are factoring in the PCI penalty twice after
acpi_penalize_isa_irq() function is called.
To avoid that, limit the newly added functionality to just PCI
interrupts so that old behavior is still maintained.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Trying to make the ISA and PCI init functionality common turned out
to be a bad idea, because the ISA path depends on external
functionality.
Restore the previous behavior and limit the refactoring to PCI
interrupts only.
Fixes: 1fcb6a813c4f "ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()"
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The change introduced in commit 103544d86976 (ACPI,PCI,IRQ: reduce
resource requirements) omitted the initially applied PCI_POSSIBLE
penalty when the IRQ is active.
Incorrect calculation of the penalty leads the ACPI code to assigning
a wrong interrupt number to a PCI INTx interrupt.
This would not be as bad as it sounds in theory. It would just cause
the interrupts to be shared and result in performance penalty.
However, some drivers (like the parallel port driver) don't like
interrupt sharing and in the above case they will causes all of
the PCI drivers wanting to share the interrupt to be unable to
request it.
The issue has not been caught in testing because the behavior is
platform-specific and depends on the peripherals ending up sharing
the IRQ and their drivers.
Before the above commit the code would add the PCI_POSSIBLE value
divided by the number of possible IRQ users to the IRQ penalty
during initialization.
Later in that code path, if the IRQ is chosen as the active IRQ or
if it is used by ISA; additional penalties are added.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
| |
The omitted parenthesis prevents the addition operation when
acpi_penalize_isa_irq function is called.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
| |
Removing the SCI penalize function as the penalty is now calculated on the
fly.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
acpi_irq_get_penalty is now calculating the penalty on the fly now.
No need to maintain global list of penalties or calculate them
at the init time. Removing duplicate code in acpi_irq_penalty_init.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
Now that the supported number of PCI IRQs are no longer capped
with 256, renaming the static array to support ISA IRQs only
and removing the MAX_IRQS constant.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
Code has been redesigned to calculate penalty requirements on the fly. This
significantly simplifies the implementation and removes some of the init
calls from x86 architecture.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
Revert commit b5bd02695471 (ACPI, PCI, irq: remove interrupt count
restriction) that introduced a boot regression on some systems
where it caused kmalloc() to be used too early.
Link: http://marc.info/?l=linux-acpi&m=145580159209240&w=2
Reported-by: Nalla, Ravikanth <ravikanth.nalla@hpe.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
| |
Revert commit 0971686954f9 "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
that depends on commit b5bd02695471 (ACPI, PCI, irq: remove interrupt
count restriction) which introduced a regression and needs to be
reverted for this reason.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
| |
acpi_penalize_isa_irq() can be written in fewer lines of code,
so do that. No functional change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Works-for: Andy Shevchenko <andy.shevchenko@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The ACPI compiler uses the extended format when used interrupt numbers
are greater than 15. The extended IRQ syntax is 32 bits according to the
ACPI spec. The code supports parsing the extended interrupt numbers.
However, due to used data structure type; the code silently truncates
interrupt numbers greater than 256.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Code currently supports 256 maximum interrupts at this moment. The patch is
reconfiguring the penalty array as a dynamic list to remove this
limitation.
A new penalty linklist has been added for all other interrupts greater than
16. If an IRQ is not found in the link list, an IRQ info structure will be
dynamically allocated on the first access and will be placed on the list
for further reuse. The list will grow by the number of supported interrupts
in the ACPI table rather than having a 256 hard limitation.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
Now we have dedicated interface acpi_penalize_sci_irq() to penalize
ISA IRQ used by ACPI SCI, so remove duplicated code to penalize ACPI SCI
in acpi_irq_penalty_init().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Avoid IRQs occupied by ISA IRQs when allocating IRQs for PCI link devices,
otherwise it may cause interrupt storm due to incompatible pin attributes.
This issue was triggered on a KVM virtual machine, which
1) uses IRQ9 for SCI in high level mode.
2) defines an PCI interrupt link device (LNKS) with IRQ9 as the only
possible irq.
3) has an PCI device referring to link device LNKS.
So it causes interrupt storm when enabling the PCI device because PCI IRQ
works in low level mode.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* acpi-pci:
ACPI, PCI: Penalize legacy IRQ used by ACPI SCI
* acpi-soc:
ACPI / LPSS: Ignore 10ms delay for Braswell
* acpi-ec:
ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations
* acpi-osl:
ACPI / osl: replace custom implementation of readq / writeq
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Nick Meier reported a regression with HyperV that "
After rebooting the VM, the following messages are logged in syslog
when trying to load the tulip driver:
tulip: Linux Tulip drivers version 1.1.15 (Feb 27, 2007)
tulip: 0000:00:0a.0: PCI INT A: failed to register GSI
tulip: Cannot enable tulip board #0, aborting
tulip: probe of 0000:00:0a.0 failed with error -16
Errors occur in 3.19.0 kernel
Works in 3.17 kernel.
"
According to the ACPI dump file posted by Nick at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
The ACPI MADT table includes an interrupt source overridden entry for
ACPI SCI:
[236h 0566 1] Subtable Type : 02 <Interrupt Source Override>
[237h 0567 1] Length : 0A
[238h 0568 1] Bus : 00
[239h 0569 1] Source : 09
[23Ah 0570 4] Interrupt : 00000009
[23Eh 0574 2] Flags (decoded below) : 000D
Polarity : 1
Trigger Mode : 3
And in DSDT table, we have _PRT method to define PCI interrupts, which
eventually goes to:
Name (PRSA, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSB, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSC, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSD, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
According to the MADT and DSDT tables, IRQ 9 may be used for:
1) ACPI SCI in level, high mode
2) PCI legacy IRQ in level, low mode
So there's a conflict in polarity setting for IRQ 9.
Prior to commit cd68f6bd53cf ("x86, irq, acpi: Get rid of special
handling of GSI for ACPI SCI"), ACPI SCI is handled specially and
there's no check for conflicts between ACPI SCI and PCI legagy IRQ.
And it seems that the HyperV hypervisor doesn't make use of the
polarity configuration in IOAPIC entry, so it just works.
Commit cd68f6bd53cf gets rid of the specially handling of ACPI SCI,
and then the pin attribute checking code discloses the conflicts
between ACPI SCI and PCI legacy IRQ on HyperV virtual machine,
and rejects the request to assign IRQ9 to PCI devices.
So penalize legacy IRQ used by ACPI SCI and mark it unusable if ACPI
SCI attributes conflict with PCI IRQ attributes.
Please refer to following links for more information:
https://bugzilla.kernel.org/show_bug.cgi?id=101301
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
Fixes: cd68f6bd53cf ("x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI")
Reported-and-tested-by: Nick Meier <nmeier@microsoft.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |/
|
|
|
|
|
|
| |
There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
| |
We already have a macro for PREFIX of "ACPI: " in
drivers/acpi/internal.h, so remove the duplicate ones
in ACPI drivers when internal.h is included.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Includes appropriate header file internal.h in pci_link.c
because function acpi_pci_link_init() has its prototype declaration in
internal.h.
This eliminates the following warning in pci_link.c:
drivers/acpi/pci_link.c:874:13: warning: no previous prototype for ‘acpi_pci_link_init’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Found with a network device in QEMU/KVM guest not working anymore.
Bisected to commit c13085e5
ACPICA: Resource Mgr: Prevent infinite loops in resource walks
That commit will check acpi_resource length strictly which causes
acpi_set_current_resources to return failure and IRQ for PCI
devices is not set properly.
Set length for all those TYPE_END_TAG acpi_resources.
[rjw: Changelog]
Bisected-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Make the ACPI PCI IRQ link driver use struct acpi_scan_handler
for representing the object used to set up ACPI interrupt links and
to remove data structures used for this purpose before unregistering
the corresponding ACPI device nodes.
This simplifies the code slightly and reduces the kernel's memory
footprint by avoiding the registration of a struct device_driver
object with the driver core and creation of its sysfs directory
which is unnecessary.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The second argument of ACPI driver .remove() operation is only used
by the ACPI processor driver and the value passed to that driver
through it is always available from the given struct acpi_device
object's removal_type field. For this reason, the second ACPI driver
.remove() argument is in fact useless, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
| |
|
|
|
|
| |
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
ACPI uses a sysdev class and a sysdev for executing
irqrouter_resume() before turning on interrupts on the boot CPU.
However, since irqrouter_resume() ignores its argument, the entire
mechanism may be replaced with a struct syscore_ops object which
is considerably simpler.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
| |
Remove unused declaration of proc_fs.h.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ids field of the struct acpi_driver is constant in <linux/acpi/acpi_bus.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
We don't need a struct containing a count and a list_head; a simple
list_head is sufficient. The list iterators handle empty lists
fine.
Furthermore, we don't need to check for null list entries because we
only add non-null entries.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
| |
Better to oops and learn about a bug than to silently cover it up.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
| |
Remove unnecessary casts and initializations.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
| |
This patch makes whitespace and indentation more consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
|
|
| |
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the acpi subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |\
| |
| |
| |
| |
| |
| | |
Conflicts:
include/acpi/acpixf.h
Signed-off-by: Len Brown <len.brown@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
According to the ACPI specification the SCI_EN flag is controlled by
the hardware, which sets this flag to inform the kernel that ACPI is
enabled. For this reason, we shouldn't try to modify SCI_EN
directly. Also, we don't need to do it in irqrouter_resume(), since
lower-level resume code takes care of enabling ACPI in case it hasn't
been enabled by the BIOS before passing control to the kernel (which
by the way is against the ACPI specification).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |/
|
|
|
|
|
| |
Sparse asked whether these could be static.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |\ |
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Catch attempts to use of acpi_driver_data on pointers of wrong type.
akpm: rewritten to use proper C typechecking and remove the
"function"-used-as-lvalue thing.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |/
|
|
|
|
|
|
|
|
|
| |
Code in `pci_link.c' is calling the internal routine `acpi_ut_evaluate_object'
which is dangerous given that it is passing a NULL pointer when it should
be passing a pointer to a real object. The patch corrects the issue by
having the code call the external routine `acpi_evaluate_object', which
correctly handles a NULL pointer.
Signed-off-by: Don Dugger <donald.d.dugger@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
acpi_penalize_isa_irq() should validate irq before using it to
index the acpi_irq_penalty[] table.
Here's the path I'm concerned about:
pnpacpi_parse_allocated_irqresource()
{
...
irq = acpi_register_gsi(gsi, triggering, polarity);
if (irq >= 0)
pcibios_penalize_isa_irq(irq, 1);
There's no guarantee that acpi_register_gsi() will return an IRQ
within the bounds of acpi_irq_penalty[].
I have not seen a failure I can attribute to this. However,
ACPI_MAX_IRQS is only 256, and I'm pretty sure ia64 can have
IRQs larger than that.
I think this should go in 2.6.27.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Silently ignore _PRS End Tags. We already ignore Start Dependent Functions in
_PRS, and we already ignore End Tags in _CRS, so we might as well ignore End
Tags in _PRS as well.
Silently ignore _PRS IRQ descriptors that mention no interrupts. The spec
allows this (section 6.4.2.1 in ACPI 3.0b spec), and it probably means the
interrupt link can't be configured at all.
This patch doesn't change any functional behavior; it just removes confusing
complaints like these:
ACPI: Blank IRQ resource
ACPI: Resource is not an IRQ entry
when parsing _PRS data "23 00 00 18 79 00" from an IBM xSeries 335 dual
Pentium IV Xeon 2.40 GHz machine. For more details, see
http://bugzilla.kernel.org/show_bug.cgi?id=11049
The "23 00 00 18" part is a three-byte-long small IRQ resource with no bits set
in the IRQ mask ("00 00"), and level-triggered, active low, shareable ("18").
The "79 00" is an End Tag (type 0x7). It is superfluous since there is no
Start Dependent Function tag and there are no resources after it, but it is
harmless.
Thanks to Gabriele Trombetti <g.trombetti.lkrnl1213@logicschema.com>
(aka Kurk) for reporting this and testing the patch.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch contains the following possible cleanups:
- make the following needlessly global code static:
- drivers/acpi/bay.c:dev_attr_eject
- drivers/acpi/bay.c:dev_attr_present
- drivers/acpi/dock.c:dev_attr_docked
- drivers/acpi/dock.c:dev_attr_flags
- drivers/acpi/dock.c:dev_attr_uid
- drivers/acpi/dock.c:dev_attr_undock
- drivers/acpi/pci_bind.c:acpi_pci_unbind()
- drivers/acpi/pci_link.c:acpi_link_lock
- drivers/acpi/sbs.c:acpi_sbs_callback()
- drivers/acpi/sbshc.c:acpi_smbus_transaction()
- drivers/acpi/sleep/main.c:acpi_sleep_prepare()
- #if 0 the following unused global functions:
- drivers/acpi/numa.c:acpi_unmap_pxm_to_node()
- remove the following unused EXPORT_SYMBOL's:
- acpi_register_gsi
- acpi_unregister_gsi
- acpi_strict
- acpi_bus_receive_event
- register_acpi_bus_type
- unregister_acpi_bus_type
- acpi_os_printf
- acpi_os_sleep
- acpi_os_stall
- acpi_os_read_pci_configuration
- acpi_os_create_semaphore
- acpi_os_delete_semaphore
- acpi_os_wait_semaphore
- acpi_os_signal_semaphore
- acpi_os_signal
- acpi_pci_irq_enable
- acpi_get_pxm
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
| |
drivers
modpost is going to use these to create e.g. acpi:ACPI0001
in modules.alias.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
