summaryrefslogtreecommitdiffstats
path: root/drivers/ata/Kconfig (follow)
Commit message (Collapse)AuthorAgeFilesLines
* ahci_imx: depend on CONFIG_MFD_SYSCONTejun Heo2013-07-261-1/+1
| | | | | | | | | ahci_imx makes use of regmap but the dependency wasn't specified in Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but CONFIG_MFD_SYSCON is not. Add the Kconfig dependency. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
* ahci_imx: add ahci sata support on imx platformsRichard Zhu2013-07-241-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | imx6q contains one Synopsys AHCI SATA controller, But it can't share ahci_platform driver with other controllers because there are some misalignments of the generic AHCI controller - the bits definitions of the HBA registers, the Vendor Specific registers, the AHCI PHY clock and the AHCI signals adjustment window(GPR13 register). - CAP_SSS(bit20) of the HOST_CAP is writable, default value is '0', should be configured to be '1' - bit0 (only one AHCI SATA port on imx6q) of the HOST_PORTS_IMPL should be set to be '1'.(default 0) - One Vendor Specific register HOST_TIMER1MS(offset:0xe0) should be configured regarding to the frequency of AHB bus clock. - Configurations of the AHCI PHY clock, and the signal parameters of the GPR13 Setup its own ahci sata driver, contained the imx6q specific initialized codes, re-use the generic ahci_platform driver, and keep the generic ahci_platform driver clean as much as possible. tj: patch description reformatted Signed-off-by: Richard Zhu <r65037@freescale.com> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Tejun Heo <tj@kernel.org>
* libata: make it clear that sata_inic162x is experimentalTejun Heo2013-07-221-1/+1
| | | | | | | | | | | | | | | | sata_inic162x never reached a state where it's reliable enough for production use and data corruption is a relatively common occurrence. Make the driver generate warning about the issues and mark the Kconfig option as experimental. If the situation doesn't improve, we'd be better off making it depend on CONFIG_BROKEN. Let's wait for several cycles and see if the kernel message draws any attention. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Martin Braure de Calignon <braurede@free.fr> Reported-by: Ben Hutchings <ben@decadent.org.uk> Reported-by: risc4all@yahoo.com
* Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds2013-07-131-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull MIPS updates from Ralf Baechle: "MIPS updates: - All the things that didn't make 3.10. - Removes the Windriver PPMC platform. Nobody will miss it. - Remove a workaround from kernel/irq/irqdomain.c which was there exclusivly for MIPS. Patch by Grant Likely. - More small improvments for the SEAD 3 platform - Improvments on the BMIPS / SMP support for the BCM63xx series. - Various cleanups of dead leftovers. - Platform support for the Cavium Octeon-based EdgeRouter Lite. Two large KVM patchsets didn't make it for this pull request because their respective authors are vacationing" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits) MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions MIPS: SEAD3: Disable L2 cache on SEAD-3. MIPS: BCM63xx: Enable second core SMP on BCM6328 if available MIPS: BCM63xx: Add SMP support to prom.c MIPS: define write{b,w,l,q}_relaxed MIPS: Expose missing pci_io{map,unmap} declarations MIPS: Malta: Update GCMP detection. Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET" MIPS: APSP: Remove <asm/kspd.h> SSB: Kconfig: Amend SSB_EMBEDDED dependencies MIPS: microMIPS: Fix improper definition of ISA exception bit. MIPS: Don't try to decode microMIPS branch instructions where they cannot exist. MIPS: Declare emulate_load_store_microMIPS as a static function. MIPS: Fix typos and cleanup comment MIPS: Cleanup indentation and whitespace MIPS: BMIPS: support booting from physical CPU other than 0 MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS MIPS: GIC: Fix gic_set_affinity infinite loop MIPS: Don't save/restore OCTEON wide multiplier state on syscalls. ...
| * MIPS: OCTEON: Rename Kconfig CAVIUM_OCTEON_REFERENCE_BOARD to CAVIUM_OCTEON_SOCDavid Daney2013-06-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CAVIUM_OCTEON_SOC most place we used to use CPU_CAVIUM_OCTEON. This allows us to CPU_CAVIUM_OCTEON in places where we have no OCTEON SOC. Remove CAVIUM_OCTEON_SIMULATOR as it doesn't really do anything, we can get the same configuration with CAVIUM_OCTEON_SOC. Signed-off-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-ide@vger.kernel.org Cc: linux-edac@vger.kernel.org Cc: linux-i2c@vger.kernel.org Cc: netdev@vger.kernel.org Cc: spi-devel-general@lists.sourceforge.net Cc: devel@driverdev.osuosl.org Cc: linux-usb@vger.kernel.org Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Patchwork: https://patchwork.linux-mips.org/patch/5295/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* | libata: do not limit R-Car SATA driver to shmobileSimon Horman2013-05-241-1/+0
|/ | | | | | | | | | | | The motivation for this is to allow the driver to be used with the r8a7790 SoC. I believe that rather than adding another SoC to the list of allowed SoCs it is better to simply remove the dependency of the driver on shmobile all together. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Tejun Heo <tj@kernel.org>
* [libata] Avoid specialized TLA's in ZPODD's KconfigAaron Lu2013-03-041-6/+7
| | | | | | | | | ODD is not a common TLA for non-ATA people so they will get confused by its meaning when they are configuring the kernel. This patch fixed this problem by using ODD only after stating what it is. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Merge tag 'upstream-linus' of ↵Linus Torvalds2013-02-251-0/+21
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev Pull libata updates from Jeff Garzik: 1) apply, and then revert, the sysfs export of ATA host controller number. Discussion was continuing after patch application, trying to figure out how to best mesh exported data with the installers, boot-time agents and other parties that want this info. 2) Merge Zero-Power Optical Device Driver (ZPODD) support, bringing the wonderfulness of sane power management to your CD/DVD device. Includes one SCSI-subsystem patch (with appropriate ACKs), adding runtime PM support to 'sr' driver. That is the ZPODD interaction bits. Patchset went through some 13 revisions before it got here; kudos to Intel for persistence. 3) pata_samsung_cf: use devm_clk_get() 4) more ata_piix, ahci PCI IDs 5) Add SATA driver for R-Car SoC 6) Convert libata to use devm_ioremap_resource (Note: I think Greg sent this to you, also) 7) Set proper Sense Key (SK) in the SCSI simulator when ATA passthrough indicates check condition. Google and specification hawks everywhere shall rejoice. * tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (22 commits) [libata] fix smatch warning for zpodd_wake_dev [libata] Set proper SK when CK_COND is set. [libata] Convert to devm_ioremap_resource() libata: add R-Car SATA driver ahci: Add Device IDs for Intel Wellsburg PCH ata_piix: Add Device IDs for Intel Wellsburg PCH [SCSI] remove can_power_off flag from scsi_device [libata] scsi: no poll when ODD is powered off [SCSI] sr: support runtime pm ahci: AHCI-mode SATA patch for Intel Avoton DeviceIDs ata_piix: IDE-mode SATA patch for Intel Avoton DeviceIDs [libata] PM code cleanup for ata port [libata] pm: differentiate system and runtime pm for ata port Revert "libata: export host controller number thru /sys" libata: do not suspend port if normal ODD is attached libata: expose pm qos flags for ata device libata: handle power transition of ODD libata: check zero power ready status for ZPODD libata: move acpi notification code to zpodd libata: identify and init ZPODD devices ...
| * libata: add R-Car SATA driverVladimir Barinov2013-02-201-0/+8
| | | | | | | | | | | | | | | | | | Add Renesas R-Car on-chip 3Gbps SATA controller driver. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> [Sergei: few bugs fixed, significant cleanup] Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * libata: identify and init ZPODD devicesAaron Lu2013-01-211-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ODD can be enabled for ZPODD if the following three conditions are satisfied: 1 The ODD supports device attention; 2 The platform can runtime power off the ODD through ACPI; 3 The ODD is either slot type or drawer type. For such ODDs, zpodd_init is called and a new structure is allocated for it to store ZPODD related stuffs. And the zpodd_dev_enabled function is used to test if ZPODD is currently enabled for this ODD. A new config CONFIG_SATA_ZPODD is added to selectively build ZPODD code. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | Merge branch 'for-linus' of ↵Linus Torvalds2013-02-221-1/+1
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 update from Martin Schwidefsky: "The most prominent change in this patch set is the software dirty bit patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and the page_test_and_clear_dirty primitive which makes the common memory management code a bit less obscure. Heiko fixed most of the PCI related fallout, more often than not missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270 patches which adds an export to tty_io to be able to resize a tty. The rest is the usual bunch of cleanups and bug fixes." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits) s390/module: Add missing R_390_NONE relocation type drivers/gpio: add missing GENERIC_HARDIRQ dependency drivers/input: add couple of missing GENERIC_HARDIRQS dependencies s390/cleanup: rename SPP to LPP s390/mm: implement software dirty bits s390/mm: Fix crst upgrade of mmap with MAP_FIXED s390/linker skript: discard exit.data at runtime drivers/media: add missing GENERIC_HARDIRQS dependency s390/bpf,jit: add vlan tag support drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency iucv: fix kernel panic at reboot s390/Kconfig: sort list of arch selected config options phylib: remove !S390 dependeny from Kconfig uio: remove !S390 dependency from Kconfig dasd: fix sysfs cleanup in dasd_generic_remove s390/pci: fix hotplug module init s390/pci: cleanup clp page allocation s390/pci: cleanup clp inline assembly s390/perf: cpum_cf: fallback to software sampling events s390/mm: provide PAGE_SHARED define ...
| * | ata: disable ATA for s390Heiko Carstens2013-02-141-1/+1
| |/ | | | | | | | | | | | | Add s390 to the list of architectures that don' want ATA. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* / drivers/ata: remove depends on CONFIG_EXPERIMENTALKees Cook2013-01-211-12/+12
|/ | | | | | | | | | The CONFIG_EXPERIMENTAL config item has not carried much meaning for a while now and is almost always enabled by default. As agreed during the Linux kernel summit, remove it from any "depends on" lines in Kconfigs. CC: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ata: add platform driver for Calxeda AHCI controllerMark Langsdorf2012-09-131-0/+8
| | | | | | | | | | | | | | Calxeda highbank SATA phy has intermittent problems bringing up a link with Gen3 drives. Retrying the phy hard reset can work-around this issue, but each reset also disables spread spectrum support. The reset function also needs to reprogram the phy to enable spread spectrum support. Create a new driver based on ahci_platform to support the Calxeda Highbank SATA controller. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] Kconfig: Elaborate that SFF is meant for legacy and PATA stuffPaul Menzel2012-08-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Building Linux for an ASUS Eee PC 701 4G with ata2.00: CFA: SILICONMOTION SM223AC, , max UDMA/66 ata2.00: 7815024 sectors, multi 0: LBA ata2.00: configured for UDMA/66 scsi 1:0:0:0: Direct-Access ATA SILICONMOTION SM n/a PQ: 0 ANSI: 5 sd 1:0:0:0: [sda] 7815024 512-byte logical blocks: (4.00 GB/3.72 GiB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 1:0:0:0: [sda] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg0 type 0 I followed the advice to not use the deprecated old PATA subsystem ATA/ATAPI/MFM/RLL support (DEPRECATED) ---> and use the ATA subsystem instead. Serial ATA and Parallel ATA drivers ---> Unfortunately I needed several tries to find out, that I needed the SFF menu I had not selected before because I had never heard that term before. I think it would have helped me, to have PATA or legacy IDE in that item’s name. Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* PATA host controller driver for ep93xxRafal Prylowski2012-05-221-0/+9
| | | | | | | | | | | | Add PATA host controller driver for ep93xx. Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl> Cc: Joao Ramos <joao.ramos@inov.pt> Cc: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ryan Mallon <rmallon@gmail.com> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_of_platform: remove direct dependency on OF_IRQRob Herring2012-01-091-1/+1
| | | | | | | | | | CONFIG_OF_IRQ is not available on some platforms and using of_irq_* breaks the build. Since resources are already populated in the platform device, get the irq from there instead. Reported-by: David S. Miller <davem@davemloft.net> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_of_platform: Add missing CONFIG_OF_IRQ dependency.David Miller2011-12-221-1/+1
| | | | | Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: remove no longer needed pata_qdi driverBartlomiej Zolnierkiewicz2011-10-141-0/+1
| | | | | | | | | | | | QDI65x0 controllers are fully supported by pata_legacy driver so remove no longer needed pata_qdi driver. Leave PATA_QDI config option for compatibility reasons and teach pata_legacy to preserve the old behavior of pata_qdi driver. Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ata: Make pata_of_platform.c compile again and work on non-PPC platformsPawel Moll2011-10-081-1/+1
| | | | | | | | | | This patch adds missing #includes, makes the driver selectable on non-PPC OF-enabled platforms and fixes property value accesses to be correct in Little Endian system. Cc: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ata: Add iMX pata supportArnaud Patard (Rtp)2011-08-191-0/+9
| | | | | | | | | | | | | | | | | | | | | | Add basic support for pata on iMX. It has been tested only on imx51. SDMA support will probably be added later so this version supports only PIO. v2: - enable only when needed IORDY - use dev_get_drvdata v3: - add missing clk_put() calls - use platform_get_irq() - fix resume code to avoid disabling IORDY on resume v4: - Remove EXPERIMENTAL and switch to depends on ARCH_MXC - Use devm_kzalloc() - make clock a must-have - Use only 1 ioremap Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ata: PATA_ARASAN_CF depends on DMADEVICESRandy Dunlap2011-07-241-0/+1
| | | | | | | | | | Fix kconfig unmet dependency warning: warning: (PATA_ARASAN_CF && VIDEO_TIMBERDALE && SND_SOC_SH4_SIU) selects DMA_ENGINE which has unmet direct dependencies (DMADEVICES) Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* pata_arasan_cf: Adding support for arasan compact flash host controllerViresh Kumar2011-03-141-0/+6
| | | | | | | | | | | The Arasan CompactFlash Device Controller has three basic modes of operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card ATA using true IDE modes. Currently driver supports only True IDE mode. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* sata_dwc_460ex: add debugging optionsSergei Shtylyov2011-03-021-0/+12
| | | | | | | | The driver makes use of the two options (CONFIG_SATA_DWC_[V]DEBUG) to enable the debug output but they both are absent in drivers/ata/Kconfig... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERTDavid Rientjes2011-01-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option is used to configure any non-standard kernel with a much larger scope than only small devices. This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes references to the option throughout the kernel. A new CONFIG_EMBEDDED option is added that automatically selects CONFIG_EXPERT when enabled and can be used in the future to isolate options that should only be considered for embedded systems (RISC architectures, SLOB, etc). Calling the option "EXPERT" more accurately represents its intention: only expert users who understand the impact of the configuration changes they are making should enable it. Reviewed-by: Ingo Molnar <mingo@elte.hu> Acked-by: David Woodhouse <david.woodhouse@intel.com> Signed-off-by: David Rientjes <rientjes@google.com> Cc: Greg KH <gregkh@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jens Axboe <axboe@kernel.dk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Robin Holt <holt@sgi.com> Cc: <linux-arch@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pata_platform: Remove CONFIG_HAVE_PATA_PLATFORM's dependencies.Nick Bowler2011-01-081-8/+8
| | | | | | | | | | | | | | | | CONFIG_HAVE_PATA_PLATFORM, by virtue of where its defined, has a dependency on CONFG_ATA and CONFIG_ATA_SFF. This causes Kconfig warnings when it is selected by various architectures, such as warning: (ARCH_VEXPRESS && <choice> || ARCH_RPC && <choice> || MACH_VPAC270 && ARCH_PXA || MACH_REALVIEW_PB11MP && ARCH_REALVIEW || MACH_REALVIEW_PBA8 && ARCH_REALVIEW || MACH_REALVIEW_PBX && ARCH_REALVIEW || MACH_BAST_IDE && ARCH_S3C2410 || MACH_ANUBIS && ARCH_S3C2410) selects HAVE_PATA_PLATFORM which has unmet direct dependencies (ATA && ATA_SFF) Since this option is only used to control visibility of the CONFIG_PATA_PLATFORM option and isn't itself visible in the menu, it is straightforward to simply remove these dependencies rather than adjust all the architectures. Signed-off-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_hpt3x2n: clarify about HPT371N supportSergei Shtylyov2011-01-081-2/+2
| | | | | | | | | | Commit 28e21c8c0d44cd63bad4c62f94ef0c5a1cb8402c (pata_hpt3x2n: Add HPT371N support and other bits) forgot to update the driver's Kconfig entry, heading comment, and module description (that also wrongly claims support of HPT302) which may confuse users... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] new driver acard_ahci, for ATP8620 host controllerDavid Milburn2011-01-061-0/+8
| | | | | | | | | Add support for Acard ATP8620 host controller. Based upon initial version by Jeff Garzik. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_mpc52xx: driver needs BMDMAWolfram Sang2010-12-241-10/+10
| | | | | | | | | | | | | | Found by this build-error if BMDMA is disabled: drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one': drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function) ... Move the Kconfig entry to the proper location as needed since 9a7780c9acb821fe1c2b6fc53f74cc2556ff5364 (libata-sff: make BMDMA optional) Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_cs5536: Add support for non-X86_32 platformsWu Zhangjin2010-12-241-1/+1
| | | | | | | | | | | | | | | pata_cs5536 does work on the other platforms(e.g. Loongson, a MIPS variant), so, remove the dependency of X86_32 and fix the building errors under the other platforms via only reserving the X86_32 specific parts for X86_32. pata_amd also supports cs5536 IDE controller, but this one saves about 33k for the compressed kernel image(vmlinuz for MIPS). Signed-off-by: Zhang Le <r0bertz@gentoo.org> Signed-off-by: Chen Jie <chenj@lemote.com> Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: remove no longer needed pata_winbond driverBartlomiej Zolnierkiewicz2010-08-261-0/+1
| | | | | | | | | | | | Winbond W83759A controller is fully supported by pata_legacy driver so remove no longer needed pata_winbond driver. Leave PATA_WINBOND_VLB config option for compatibility reasons and teach pata_legacy to preserve the old behavior of pata_winbond driver. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Merge branches 'master' and 'devel' into for-linusRussell King2010-08-111-0/+11
|\ | | | | | | | | | | Conflicts: arch/arm/Kconfig arch/arm/mm/Kconfig
| * [ARM] pata_pxa: DMA-capable PATA driverMarek Vasut2010-06-181-0/+11
| | | | | | | | | | | | | | | | | | | | This patch adds a driver for a harddrive attached to PXA address and data bus. Unlike pata_platform, this driver allows usage of PXA DMA controller, making the transmission speed 3x higher. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* | [libata] Add Samsung PATA controller driver, pata_samsung_cfAbhilash Kesavan2010-08-021-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Samsung PATA controller. This driver is based on the Libata subsystem and references the earlier patches sent for IDE subsystem. Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Sergei Shtylyov <sshtylyov@mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | [libata] Add 460EX on-chip SATA driver, sata_dwc_460exRupjyoti Sarmah2010-08-021-0/+9
|/ | | | | | | | | | This patch enables the on-chip DWC SATA controller of the AppliedMicro processor 460EX. Signed-off-by: Rupjyoti Sarmah <rsarmah@appliedmicro.com> Signed-off-by: Mark Miesfeld <mmiesfeld@appliedmicro.com> Signed-off-by: Prodyut Hazarika <phazarika@appliedmicro.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata-sff: trivial corrections to Kconfig help textStefan Richter2010-06-021-3/+3
| | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata-sff: make BMDMA optionalTejun Heo2010-05-261-243/+268
| | | | | | | | | | | | | | | | | | | | | Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA. In Kconfig, drivers are grouped into five groups - non-SFF native, SFF w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic fallback / legacy ones. Kconfig and Makefile are reorganized according to the groups and ordered alphabetically inside each group. ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and functions. This increase the binary size slightly when BMDMA is enabled but on both native-only and PIO-only configurations the size is slightly reduced. Either way, the size difference is insignificant. This change is more meaningful to signify the separation between SFF and BMDMA and as a tool to verify the separation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sata_inic162x: inic162x is not dependent on CONFIG_ATA_SFFTejun Heo2010-05-151-6/+6
| | | | | | | | sata_inic162x no longer uses SFF interface. Move it out of CONFIG_ATA_SFF. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: Add platform driverAnton Vorontsov2010-05-141-0/+8
| | | | | | | | This can be used for AHCI-compatible interfaces implemented inside System-On-Chip solutions, or AHCI devices connected via localbus. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: Allow pata_legacy to be built on non-ISA but PCI systemsAlan Cox2010-03-011-2/+2
| | | | | | | | | This is needed for some unsupported hardware setups on strange 64bit mainboards where crazy stuff has been done like putting flash ata adapters on the LPC bus, or where the real hardware is hidden/confused. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ACPI: do not select ACPI_DOCK from ATA_ACPICarlos R. Mafra2009-12-241-1/+0
| | | | | | | | | | | | | | | | | | | In March 2008 commit 0ac4a3c2fbbcadc3e96e4dc47d4ae802d66e6f67 ("ACPI: fix ATA_ACPI build") made CONFIG_ACPI_DOCK be selected by CONFIG_ATA_ACPI because of a build error when CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m. However, in September 2008 commit 898b054f3eec5921320ae8614b5bdd7b07ea5b43 ("dock: make dock driver not a module") removed the possibility of having CONFIG_ACPI_DOCK=m and therefore there is no need for selecting it when CONFIG_ATA_ACPI=y. This makes the kernel ~5 Kb smaller for people who don't have a dock by allowing them to not have ACPI_DOCK compiled-in because of ATA_ACPI=y. Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de> Cc: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
* Merge commit 'origin/master' into nextBenjamin Herrenschmidt2009-12-091-16/+25
|\ | | | | | | | | Conflicts: include/linux/kvm.h
| * pata_piccolo: Driver for old Toshiba chipsetsAlan Cox2009-12-031-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | We were never able to get docs for this out of Toshiba for years. Dave Barnes produced a NetBSD driver however and from that we can fill in the needed tables. As we correct the PCI identifiers a bit also update the old ide generic driver at the same time so it stays compiling. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * [libata] PATA: Update experimental tagsAlan Cox2009-12-031-15/+15
| | | | | | | | | | Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * libata: remove experimental tag on PATA driversRobert Hancock2009-12-031-1/+1
| | | | | | | | | | | | | | | | | | | | Remove the experimental tag on Parallel ATA drivers. Though some of the individual PATA drivers are still marked as experimental, as a group they can hardly be considered to be, given they've been used in various distros for some time. Signed-off-by: Robert Hancock <hancockrwd@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | libata/drivers: Add driver for Apple "MacIO" IDE controllerBenjamin Herrenschmidt2009-12-091-0/+10
|/ | | | | | | | | | | | | | | This is a libata driver for the "macio" IDE controller used on most Apple PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c It supports all the features of its predecessor, including mediabay hotplug and suspend/resume. It should also support module load/unload. The timing calculations have been simplified to use pre-calculated tables compared to drivers/ide/pmac.c and it uses the new mediabay interface provided by a previous patch. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Tejun Heo <tj@kernel.org>
* libata: Add pata_atp867x driver for Artop/Acard ATP867X controllersJohn(Jung-Ik) Lee2009-09-171-0/+9
| | | | | | | | | | | This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls. Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes from Eric Uhrhane <ericu@google.com>. Signed-off-by: John(Jung-Ik) Lee <jilee@google.com> Reviewed-by: Grant Grundler <grundler@google.com> Reviewed-by: Gwendal Gringo <gwendal@google.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] Add pata_rdc driver for RDC ATA devicesAlan Cox2009-09-021-0/+10
| | | | | | | From: Alan Cox <alan@linux.intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: add command name parsing for error outputRobert Hancock2009-09-021-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | This patch improve libata's output for error/notification messages to allow easier comprehension and debugging: When ATAPI commands issued through the SCSI layer fail, use SCSI functions to print the CDB in human-readable form instead of just dumping out the CDB in hex. Print out the name of the failed command (as defined by the ATA specification) in error handling output along with the raw register contents. When reporting status of ACPI taskfile commands executed on resume, also output the names of the commands being executed (or not) in readable form. Since the extra data for printing command names increases kernel size slightly, a config option has been added to allow disabling command name output (as well as some of the error register parsing) for those highly sensitive to kernel text size. Signed-off-by: Robert Hancock <hancockrwd@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] PATA driver for CF interface on AT91SAM9260 SoCSergey Matyukevich2009-06-231-0/+8
| | | | | | | | This patch provides PATA driver for CompactFlash interface in True IDE mode on AT91SAM9260 SoC. Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 10:45:38 +0100