summaryrefslogtreecommitdiffstats
path: root/drivers/ata/ahci.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* ahci: force CAP_NCQ for earlier NV MCPsTejun Heo2009-04-131-24/+33
| | | | | | | | | | Along with MCP65, MCP67 and 73 also don't set CAP_NCQ. Force it. Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: NightFox <zaceni2@yandex.ru> Cc: Peer Chen <pchen@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Merge branch 'upstream-linus' of ↵Linus Torvalds2009-04-071-2/+15
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_mv: shorten register names sata_mv: workaround errata SATA#13 sata_mv: cosmetic renames sata_mv: workaround errata SATA#26 sata_mv: workaround errata PCI#7 sata_mv: replace 0x1f with ATA_PIO4 (v2) sata_mv: fix irq mask races sata_mv: revert SoC irq breakage libata: ahci enclosure management bios workaround ata: Add TRIM infrastructure ata_piix: VGN-BX297XP wants the controller power up on suspend libata: Remove some redundant casts from pata_octeon_cf.c pata_artop: typo
| * libata: ahci enclosure management bios workaroundDavid Milburn2009-04-071-2/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | During driver initialization ahci_start_port may not be able to turn LEDs off because the hardware may still be transmitting a message. And since the BIOS may not be setting the LEDs to off the drive LEDs may end up in a fault state. This has been seen on ICH9r and ICH10r when configured in AHCI mode instead of RAID mode, this patch doesn't key off a specific set of device IDs but will give the EM transmit bit a chance to clear if busy. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)Yang Hongyang2009-04-071-3/+3
| | | | | | | | | | | | | | | | Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | dma-mapping: replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)Yang Hongyang2009-04-071-2/+2
|/ | | | | | | | Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [libata] ahci: correct enclosure LED state saveDavid Milburn2009-03-251-1/+1
| | | | | | | | | | | | | | | | | | ahci_transmit_led_message saves off the led_state with a value that includes the port number OR'd in, this incorrect value maybe reported back in ahci_led_store. For instance, if you turn off all the leds for port 1 and cat the value back it will report 1 instead of 0. # echo 0 > /sys/class/scsi_host/host1/em_message # cat /sys/class/scsi_host/host1/em_message 1 Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] convert drivers to use ata.h mode mask definesErik Inge Bolsø2009-03-251-8/+8
| | | | | | | No functional changes in this patch. Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: Blacklist HP Compaq 6720s that spins off disks during ACPI power offMaciej Rutecki2009-03-251-0/+9
| | | | | | | | | | Blacklist HP Compaq 6720s so that it doesn't play a "spin down, spin up, spin down" ping-pong with the hard disk during system power off. Signed-off-by: Maciej Rutecki <maciej.rutecki@gmail.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: drop intx manipulation on msi enableTejun Heo2009-03-251-2/+2
| | | | | | | | | | | | | | | There's no need to turn off intx explicitly on msi enable. This is automatically handled by pci. Drop it. This might be needed on machines if the BIOS turns intx off during boot. However, there's no evidence of such behavior for ahci and the only such case seems to be ICH5 PATA according to ata_piix. Also, given the way ahci operates, it's highly unlikely BIOS ever disables IRQ for the controller. However, as this change has slight possibility of introducing failure, please schedule it for #upstream. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: Add the Device IDs for MCP89 and remove IDs of MCP7B to/from ahci.cpeerchen2009-03-051-12/+12
| | | | | | | | | Added the Device IDs for MCP89 AHCI controller. Removed the IDs of MCP7B because this chipset had been cancelled. Signed-off-by: Peer Chen <peerchen@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: add a module parameter to ignore the SSS flags for async scanningArjan van de Ven2009-02-031-1/+8
| | | | | | | | | | | | The SSS flag, which directs the OS to spin up one disk at a time to not have the PSU blow out, sometimes gets set even when not needed. The effect of this is a longer-than-needed boot time. This patch adds a module parameter that makes the driver ignore SSS at least as far as the parallel scan during boot is concerned... Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* SATA AHCI: Blacklist system that spins off disks during ACPI power offRafael J. Wysocki2009-01-271-0/+32
| | | | | | | | | | | | | | | | | Some notebooks from HP have the problem that their BIOSes attempt to spin down hard drives before entering ACPI system states S4 and S5. This leads to a yo-yo effect during system power-off shutdown and the last phase of hibernation when the disk is first spun down by the kernel and then almost immediately turned on and off by the BIOS. This, in turn, may result in shortening the disk's life times. To prevent this from happening we can blacklist the affected systems using DMI information. Blacklist HP nx6310 that uses the AHCI driver. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: Add a per-host flag to opt-in into parallel port probesArjan van de Ven2009-01-111-0/+3
| | | | | | | | | | | This patch adds a per host flag that allows drivers to opt in into having its busses scanned in parallel. Drivers that do not set this flag get their ports scanned in the "original" sequence. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [libata] ahci: Withdraw IGN_SERR_INTERNAL for SB800 SATAShane Huang2009-01-081-2/+6
| | | | | | | | | | | There is an issue in ATI SB600/SB700 SATA that PxSERR.E should not be set on some conditions, which will lead to many SATA ODD error messages. commit 55a61604cd1354e1783364e1c901034f2f474b7d is the workaround. Since SB800 fixed this HW issue, IGN_SERR_INTERNAL should be withdrawn for SB800. Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] ahci: Add SATA GEN3 related messagesShane Huang2009-01-081-0/+2
| | | | | | | | The present AHCI driver seems to support SATA GEN 3 speed, but the related messages should be modified. Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: beef up iteratorsTejun Heo2008-12-291-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There currently are the following looping constructs. * __ata_port_for_each_link() for all available links * ata_port_for_each_link() for edge links * ata_link_for_each_dev() for all devices * ata_link_for_each_dev_reverse() for all devices in reverse order Now there's a need for looping construct which is similar to __ata_port_for_each_link() but iterates over PMP links before the host link. Instead of adding another one with long name, do the following cleanup. * Implement and export ata_link_next() and ata_dev_next() which take @mode parameter and can be used to build custom loop. * Implement ata_for_each_link() and ata_for_each_dev() which take looping mode explicitly. The following iteration modes are implemented. * ATA_LITER_EDGE : loop over edge links * ATA_LITER_HOST_FIRST : loop over all links, host link first * ATA_LITER_PMP_FIRST : loop over all links, PMP links first * ATA_DITER_ENABLED : loop over enabled devices * ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order * ATA_DITER_ALL : loop over all devices * ATA_DITER_ALL_REVERSE : loop over all devices in reverse order This change removes exlicit device enabledness checks from many loops and makes it clear which ones are iterated over in which direction. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: ahci enclosure management bit maskDavid Milburn2008-10-281-12/+23
| | | | | | | Enclosure management bit mask definitions. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: ahci enclosure management led syncDavid Milburn2008-10-281-0/+3
| | | | | | | Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: Add support for Promise PDC42819Mark Nelson2008-10-281-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | Add an appropriate entry for the Promise PDC42819 controller. It has an AHCI mode and so far works correctly with board_ahci. This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port) software-based RAID cards (for which there is a binary driver, t3sas) and can be found on some motherboards, for example the MSI K9A2 Platinum, which calls the chip a Promise T3 controller. Although this controller also supports SAS devices, its default bootup mode is AHCI and the binary driver has to do some magic to get the chip into the appropriate mode to drive SAS disks. Seeing as no documentation is provided by Promise, adding this entry to the ahci driver allows the controller to be useful to people as a SATA controller (with no ill effects on the system if a SAS disk is connected - probing of the port just times out with "link online but device misclassified"), without having to resort to using the binary driver. Users who require SAS or the proprietary software raid can get this functionality using the binary driver. Signed-off-by: Mark Nelson <mdnelson8@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: Implement disk shock protection supportElias Oltmanns2008-09-291-0/+1
| | | | | | | | | | | | | | | On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD FEATURE as specified in ATA-7 is issued to the device and processing of the request queue is stopped thereafter until the specified timeout expires or user space asks to resume normal operation. This is supposed to prevent the heads of a hard drive from accidentally crashing onto the platter when a heavy shock is anticipated (like a falling laptop expected to hit the floor). In fact, the whole port stops processing commands until the timeout has expired in order to avoid any resets due to failed commands on another device. Signed-off-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: make SCR access ops per-linkTejun Heo2008-09-291-12/+12
| | | | | | | | | | | | | Logically, SCR access ops should take @link; however, there was no compelling reason to convert all SCR access ops when adding @link abstraction as there's one-to-one mapping between a port and a non-PMP link. However, that assumption won't hold anymore with the scheduled addition of slave link. Make SCR access ops per-link. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDsSeth Heasley2008-09-081-0/+2
| | | | | | | Add the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: disable PMP for marvell ahcisTejun Heo2008-09-081-1/+1
| | | | | | | | | | | | | Marvell ahcis don't play nicely with PMPs. Disable it. Reported by KueiHuan Chen in the following thread. http://thread.gmane.org/gmane.linux.ide/33296 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: KueiHuan Chen <kueihuan.chen@gmail.com> Cc: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci, pata_marvell: play nicely togetherAlan Cox2008-09-081-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I've been chasing Jeff about this for months. Jeff added the Marvell device identifiers to the ahci driver without making the AHCI driver handle the PATA port. This means a lot of users can't use current kernels and in most distro cases can't even install. This has been going on since March 2008 for the 6121 Marvell, and late 2007 for the 6145!!! This was all pointed out at the time and repeatedly ignored. Bugs assigned to Jeff about this are ignored also. To quote Jeff in email > "Just switch the order of 'ahci' and 'pata_marvell' in > /etc/modprobe.conf, then use Fedora's tools regenerate the initrd. > See? It's not rocket science, and the current configuration can be > easily made to work for Fedora users." (Which isn't trivial, isn't end user, shouldn't be needed, and as it usually breaks at install time is in fact impossible) To quote Jeff in August 2007 > " mv-ahci-pata > Marvell 6121/6141 PATA support. Needs fixing in the 'PATA controller > command' area before it is usable, and can go upstream." Only he add the ids anyway later and caused regressions, adding a further id in March causing more regresions. The actual fix for the moment is very simple. If the user has included the pata_marvell driver let it drive the ports. If they've only selected for SATA support give them the AHCI driver which will run the port a fraction faster. Allow the user to control this decision via ahci.marvell_enable as a module parameter so that distributions can ship 'it works' defaults and smarter users (or config tools) can then flip it over it desired. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: sis controllers actually can do PMPTejun Heo2008-08-221-3/+3
| | | | | | | | | | | | | | | | | | | SIS controllers were blacklisted for PMP as enabling it made device detection fail whether the device was PMP or not - the natural conclusion was the controller chokes on SRST w/ pmp==15. However, it turned out that the controller just didn't like issuing SRST after hardreset w/o clearing SError first. Interestingly, the SRST itself succeeds but the following commands fail. If SError is cleared between hardreset and SRST, which is the default behavior now, everything works fine and SIS controllers work with PMPs happily. Remove PMP blacklisting for SIS AHCIs. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Piter PUNK <piterpunk@slackware.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDsSeth Heasley2008-08-221-0/+2
| | | | | | | | | Resend with proper whitespace. This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Fix ahci driver 'flags' typeLinus Torvalds2008-07-251-1/+1
| | | | | | | | The new type checking of the flags arguments to irqsave and friends (commit 3f307891ce0e7b0438c432af1aacd656a092ff45) pointed out this thing with a big nice warning. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* AHCI: Remove an unnecessary flush from ahci_qc_issueMatthew Wilcox2008-07-141-1/+0
| | | | | | | | | | | | | In an I/O heavy workload (IOZone), ahci_qc_issue is the second-highest consumer of CPU cycles. Removing the flush gets us approximately 10% bandwidth improvement. I believe this to be because the CPU can start queueing the next request instead of waiting for the readl() to flush the writes to the device. The flush isn't necessary because we're using a 'queue' metaphor; we don't guarantee the command has got to the device, nor do we need to guarantee the command has got to the controller. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* AHCI: speed up resumeZhang Rui2008-07-141-3/+6
| | | | | | | | | | | | | | | | During resume, sleep 1 second to wait for the HBA reset to finish is a waste of time. According to the AHCI 1.2 spec, We should poll the HOST_CTL register, and return error if the host reset is not finished within 1 second. Test results show that the HBA reset can be done quickly(in usecs). And this patch may save nearly 1 second during resume. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata/ahci: enclosure management supportKristen Carlson Accardi2008-07-141-2/+319
| | | | | | | Add Enclosure Management support to libata and ahci. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: give another shot at clearing all bits in irq_statTejun Heo2008-07-051-3/+13
| | | | | | | | | | | | | | | Commit ea0c62f7cf70f13a67830471b613337bd0c9a62e tried to clear all bits in irq_stat but it didn't actually achieve that as irq_stat was anded with port_map right after read. This patch makes ahci driver always use the unmasked value to clear irq_status. While at it, add explanation on the peculiarities of ahci IRQ clearing. This was spotted by Linus Torvalds. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* ahci: always clear all bits in irq_statTejun Heo2008-07-041-6/+3
| | | | | | | | | | | | | | | | | Some AHCI controllers (ICH7 was reported) set pending bit in HOST_IRQ_STAT for non-existent ports and when it's not cleared falls into IRQ storm. Always clear full irq_stat instead of only the bits that are handled. As nothing changes for recognized ports, the risk of breaking things is pretty low. Reported and verified by Philipp Thomas in the following suse bugzilla. https://bugzilla.novell.com/attachment.cgi?id=215692 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Philipp Thomas <pth@novell.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: sis can't do PMPTejun Heo2008-06-191-3/+12
| | | | | | | | | | | | | From: Piter PUNK <piterpunk@slackware.com> SiS AHCIs say they can do PMP but can't and fail detection if SRST w/ pmp==15 is used. Turn off PMP support. tj: added patch description, adapted patch to #upstream-fixes and renamed board_ahci_sis to board_ahci_nopmp. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: jmb361 has only one portTejun Heo2008-06-191-0/+8
| | | | | | | | | | | JMB361 has only one port but reports it has two causing longish probe failure on the second one. Quirk it. Reported by Gajo Petrovic in bz 10911. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Gajo Petrovic <gajo01@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: Workaround HW bug for SB600/700 SATA controller PMP supportShane Huang2008-06-131-17/+82
| | | | | | | | | There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads to soft reset failure. This patch can fix the bug. Signed-off-by: Shane Huang <shane.huang@amd.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: workarounds for mcp65Tejun Heo2008-06-131-9/+31
| | | | | | | | | | MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1 can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ and apply appropriate workarounds. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Peer Chen <pchen@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: change the Device IDs of nvidia MCP7B AHCI controller in ahci.cpeerchen2008-05-301-4/+4
| | | | | | | | | Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c, as the actual PCI IDs deployed in the field differed from the forecasted ones preemptively placed in the driver. Signed-off-by: Peer Chen <peerchen@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: improve post-reset device ready testTejun Heo2008-05-061-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that the device isn't ready yet. It looks like they use 0xff if device presence is detected but connection isn't established. 0x77 or 0x7f after connection is established and use the value from signature FIS after receiving it. This patch implements ata_check_ready(), which takes TF status value and determines whether the port is ready or not considering the above and other conditions, and use it in @check_ready() functions. This is safe as both 0x77 and 0x7f aren't valid ready status value even though they have BSY bit cleared. This fixes hot plug detection failures which can be triggered with certain drives if they aren't already spun up when the data connector is hot plugged. Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with eight drives from all major vendors. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: SB600 ahci can't do MSI, blacklist that capabilityTejun Heo2008-04-291-1/+1
| | | | | | | | This fixes bz#10507. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Shane Huang <Shane.Huang@amd.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ahci: retry enabling AHCI a few times before spitting out WARN_ON()Tejun Heo2008-04-251-2/+13
| | | | | | | | | | Some chips need AHCI_EN set more than once to actually set it. Try a few times before giving up and spitting out WARN_ON(). Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Peer Chen <pchen@nvidia.com> Cc: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* SCSI: convert struct class_device to struct deviceTony Jones2008-04-201-2/+2
| | | | | | | | | | | | | It's big, but there doesn't seem to be a way to split it up smaller... Signed-off-by: Tony Jones <tonyj@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Cc: Roland Dreier <rolandd@cisco.com> Cc: Sean Hefty <sean.hefty@intel.com> Cc: Hal Rosenstock <hal.rosenstock@gmail.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* libata: move link onlineness check out of softreset methodsTejun Heo2008-04-171-6/+0
| | | | | | | | | | | | | | | | | | | Currently, SATA softresets should do link onlineness check before actually performing SRST protocol but it doesn't really belong to softreset. This patch moves onlineness check in softreset to ata_eh_reset() and ata_eh_followup_srst_needed() to clean up code and help future sata_mv changes which need clear separation between SCR and TF accesses. sata_fsl is peculiar in that its softreset really isn't softreset but combination of hardreset and softreset. This patch adds dummy private ->prereset to keep the current behavior but the driver really should implement separate hard and soft resets and return -EAGAIN from hardreset if it should be follwed by softreset. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: implement PMP helpersTejun Heo2008-04-171-24/+6
| | | | | | | | | | | Implement helpers to test whether PMP is supported, attached and determine pmp number to use when issuing SRST to a link. While at it, move ata_is_host_link() so that it's together with the two new PMP helpers. This change simplifies LLDs and helps making PMP support optional. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: don't use ap->ioaddr in non-SFF driversTejun Heo2008-04-171-10/+5
| | | | | | | ap->ioaddr is to carry addresses for TF and BMDMA registers of a SFF controller, don't abuse it in non-SFF controllers. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: remove check_status from non-SFF driversTejun Heo2008-04-171-12/+2
| | | | | | | | Now that all SFF stuff is separated out of core layer, core layer doesn't call ops->[alt_]check_status(). In fact, no one calls them for non-SFF drivers anymore. Kill them. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: replace tf_read with qc_fill_rtf for non-SFF driversTejun Heo2008-04-171-10/+11
| | | | | | | | | | | | | | | | | | | | Now that all SFF stuff is separated out of core layer, core layer doesn't call ops->tf_read directly. It gets called only via ops->qc_fill_rtf() for non-SFF drivers. This patch directly implements private ops->qc_fill_rtf() for non-SFF controllers and kill ops->tf_read(). This is much cleaner for non-SFF controllers as some of them have to cache SFF register values in private data structure and report the cached values via ops->tf_read(). Also, ops->tf_read() gets nasty for controllers which don't have clear notion of TF registers when operation is not in progress. As this change makes default ops->qc_fill_rtf unnecessary, move ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where it belongs. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: drop @finish_qc from ata_qc_complete_multiple()Tejun Heo2008-04-171-1/+1
| | | | | | | | | | | | | ata_qc_complete_multiple() took @finish_qc and called it on every qc before completing it. This was to give opportunity to update TF cache before ata_qc_complete() tries to fill result_tf. Now that result TF is a separate operation, this is no longer necessary. Update sata_sil24, which was the only user of this mechanism, such that it implements its own ops->qc_fill_rtf() and drop @finish_qc from ata_qc_complete_multiple(). Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: unify mechanism to request follow-up SRSTTejun Heo2008-04-171-3/+0
| | | | | | | | | | | | | Previously, there were two ways to trigger follow-up SRST from hardreset method - returning -EAGAIN and leaving all device classes unmodified. Drivers never used the latter mechanism and the only use case for the former was when hardreset couldn't classify. Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST if classification is required". This change removes unnecessary follow-up SRSTs and simplifies reset implementations. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: clear SError after link resumeTejun Heo2008-04-171-5/+0
| | | | | | | | | | | | | | | SError used to be cleared in ->postreset. This has small hotplug race condition. If a device is plugged in after reset is complete but postreset hasn't run yet, its hotplug event gets lost when SError is cleared. This patch makes sata_link_resume() clear SError. This kills the race condition and makes a lot of sense as some PMP and host PHYs don't work properly without SError cleared. This change makes sata_pmp_std_{pre|post}_reset()'s unnecessary as they become identical to ata_std counterparts. It also simplifies sata_pmp_hardreset() and ahci_vt8251_hardreset(). Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: move generic hardreset code from sata_sff_hardreset() to ↵Tejun Heo2008-04-171-15/+20
| | | | | | | | | | | | | | | | sata_link_hardreset() sata_sff_hardreset() contains link readiness wait logic which isn't SFF specific. Move that part into sata_link_hardreset(), which now takes two more parameters - @online and @check_ready. Both are optional. The former is out parameter for link onlineness after reset. The latter is used to wait for link readiness after hardreset. Users of sata_link_hardreset() is updated to use new funtionality and ahci_hardreset() is updated to use sata_link_hardreset() instead of sata_sff_hardreset(). This doesn't really cause any behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 03:52:50 +0100