summaryrefslogtreecommitdiffstats
path: root/drivers/bcma (follow)
Commit message (Collapse)AuthorAgeFilesLines
* Merge tag 'mtd/changes-for-5.18' of ↵Linus Torvalds2022-03-251-1/+19
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux Pull MTD updates from Miquel Raynal: "There has been a lot of activity in the MTD subsystem recently, with a number of SPI-NOR cleanups as well as the introduction of ECC engines that can be used by SPI controllers (hence a few SPI patches in here). Core MTD changes: - Replace the expert mode symbols with a single helper - Fix misuses of of_match_ptr() - Remove partid and partname debugfs files - tests: Fix eraseblock read speed miscalculation for lower partition sizes - TRX parser: Allow to use on MediaTek MIPS SoCs MTD driver changes: - spear_smi: use GFP_KERNEL - mchp48l640: Add SPI ID table - mchp23k256: Add SPI ID table - blkdevs: Avoid soft lockups with some mtd/spi devices - aspeed-smc: Improve probe resilience Hyperbus changes: - HBMC_AM654 should depend on ARCH_K3 NAND core changes: - ECC: - Add infrastructure to support hardware engines - Add a new helper to retrieve the ECC context - Provide a helper to retrieve a pilelined engine device NAND-ECC changes: - Macronix ECC engine: - Add Macronix external ECC engine support - Support SPI pipelined mode - Make two read-only arrays static const - Fix compile test issue Raw NAND core changes: - Fix misuses of of_match_node() - Rework of_get_nand_bus_width() - Remove of_get_nand_on_flash_bbt() wrapper - Protect access to rawnand devices while in suspend - bindings: Document the wp-gpios property Rax NAND controller driver changes: - atmel: Fix refcount issue in atmel_nand_controller_init - nandsim: - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern - Merge repeat codes in ns_switch_state - Replace overflow check with kzalloc to single kcalloc - rockchip: Fix platform_get_irq.cocci warning - stm32_fmc2: Add NAND Write Protect support - pl353: Set the nand chip node as the flash node - brcmnand: Fix sparse warnings in bcma_nand - omap_elm: Remove redundant variable 'errors' - gpmi: - Support fast edo timings for mx28 - Validate controller clock rate - Fix controller timings setting - brcmnand: - Add BCMA shim - BCMA controller uses command shift of 0 - Allow platform data instantation - Add platform data structure for BCMA - Allow working without interrupts - Move OF operations out of brcmnand_init_cs() - Avoid pdev in brcmnand_init_cs() - Allow SoC to provide I/O operations - Assign soc as early as possible Onenand changes: - Check for error irq SPI-NAND core changes: - Delay a little bit the dirmap creation - Create direct mapping descriptors for ECC operations SPI-NAND driver changes: - macronix: Use random program load SPI NOR core changes: - Move vendor specific code out of the core into vendor drivers. - Unify all function and object names in the vendor modules. - Make setup() callback optional to improve readability. - Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash declaration. SPI changes: - Macronix SPI controller: - Fix the transmit path - Create a helper to configure the controller before an operation - Create a helper to ease the start of an operation - Add support for direct mapping - Add support for pipelined ECC operations - spi-mem: - Introduce a capability structure - Check the controller extra capabilities - cadence-quadspi/mxic: Provide capability structures - Kill the spi_mem_dtr_supports_op() helper - Add an ecc parameter to the spi_mem_op structure Binding changes: - Dropped mtd/cortina,gemini-flash.txt - Convert BCM47xx partitions to json-schema - Vendor prefixes: Clarify Macronix prefix - SPI NAND: Convert spi-nand description file to yaml - Raw NAND chip: Create a NAND chip description - Raw NAND controller: - Harmonize the property types - Fix a comment in the examples - Fix the reg property description - Describe Macronix NAND ECC engine - Macronix SPI controller: - Document the nand-ecc-engine property - Convert to yaml - The interrupt property is not mandatory" * tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits) mtd: nand: ecc: mxic: Fix compile test issue mtd: nand: mxic-ecc: make two read-only arrays static const mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3 mtd: core: Remove partid and partname debugfs files dt-bindings: mtd: partitions: convert BCM47xx to the json-schema mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init mtd: rawnand: rockchip: fix platform_get_irq.cocci warning mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set mtd: spi-nor: renumber flags mtd: spi-nor: slightly change code style in spi_nor_sr_ready() mtd: spi-nor: spansion: rename vendor specific functions and defines mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag mtd: spi-nor: move all spansion specifics into spansion.c mtd: spi-nor: spansion: slightly rework control flow in late_init() mtd: spi-nor: micron-st: rename vendor specific functions and defines mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag mtd: spi-nor: move all micron-st specifics into micron-st.c mtd: spi-nor: xilinx: correct the debug message mtd: spi-nor: xilinx: rename vendor specific functions and defines ...
| * mtd: rawnand: brcmnand: Add platform data structure for BCMAFlorian Fainelli2022-01-231-1/+19
| | | | | | | | | | | | | | | | | | | | | | | | Update the BCMA's chipcommon nand flash driver to detect which chip-select is used and pass that information via platform data to the brcmnand driver. Make sure that the brcmnand platform data structure is always at the beginning of the platform data of the "nflash" device created by BCMA to allow brcmnand to safely de-reference it. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-7-f.fainelli@gmail.com
* | bcma: gpio: remove redundant re-assignment of chip->ownerColin Ian King2022-03-101-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | There are two identical assignments of chip->owner to the same value, the second assignment is redundant and can be removed. Cleans up cppcheck warning: drivers/bcma/driver_gpio.c:184:15: style: Variable 'chip->owner' is reassigned a value before the old one has been used. [redundantAssignment] Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220303085841.1124766-1-colin.i.king@gmail.com
* | bcma: cleanup commentsTom Rix2022-02-215-11/+11
|/ | | | | | | | | | | | | | | | | | | Remove the second 'info'. Replacements 'adventages' with 'advantages' 'strenth' with 'strength' 'atleast' with 'at least' 'thr'u'' with 'through' 'capabilty' with 'capability' 'controll' with 'control' 'ourself' with 'ourselves' 'noone' with 'no one' 'cores' to 'core's' and 'core' Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220213213121.2806376-1-trix@redhat.com
* Merge tag 'pci-v5.16-changes' of ↵Linus Torvalds2021-11-061-5/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull pci updates from Bjorn Helgaas: "Enumeration: - Conserve IRQs by setting up portdrv IRQs only when there are users (Jan Kiszka) - Rework and simplify _OSC negotiation for control of PCIe features (Joerg Roedel) - Remove struct pci_dev.driver pointer since it's redundant with the struct device.driver pointer (Uwe Kleine-König) Resource management: - Coalesce contiguous host bridge apertures from _CRS to accommodate BARs that cover more than one aperture (Kai-Heng Feng) Sysfs: - Check CAP_SYS_ADMIN before parsing user input (Krzysztof Wilczyński) - Return -EINVAL consistently from "store" functions (Krzysztof Wilczyński) - Use sysfs_emit() in endpoint "show" functions to avoid buffer overruns (Kunihiko Hayashi) PCIe native device hotplug: - Ignore Link Down/Up caused by resets during error recovery so endpoint drivers can remain bound to the device (Lukas Wunner) Virtualization: - Avoid bus resets on Atheros QCA6174, where they hang the device (Ingmar Klein) - Work around Pericom PI7C9X2G switch packet drop erratum by using store and forward mode instead of cut-through (Nathan Rossi) - Avoid trying to enable AtomicOps on VFs; the PF setting applies to all VFs (Selvin Xavier) MSI: - Document that /sys/bus/pci/devices/.../irq contains the legacy INTx interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry Song) VPD: - Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere in the possible VPD space; use these to simplify the cxgb3 driver (Heiner Kallweit) Peer-to-peer DMA: - Add (not subtract) the bus offset when calculating DMA address (Wang Lu) ASPM: - Re-enable LTR at Downstream Ports so they don't report Unsupported Requests when reset or hot-added devices send LTR messages (Mingchuang Qiao) Apple PCIe controller driver: - Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc Zyngier) Cadence PCIe controller driver: - Return success when probe succeeds instead of falling into error path (Li Chen) HiSilicon Kirin PCIe controller driver: - Reorganize PHY logic and add support for external PHY drivers (Mauro Carvalho Chehab) - Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro Carvalho Chehab) - Add Kirin 970 support (Mauro Carvalho Chehab) - Make driver removable (Mauro Carvalho Chehab) Intel VMD host bridge driver: - If IOMMU supports interrupt remapping, leave VMD MSI-X remapping enabled (Adrian Huang) - Number each controller so we can tell them apart in /proc/interrupts (Chunguang Xu) - Avoid building on UML because VMD depends on x86 bare metal APIs (Johannes Berg) Marvell Aardvark PCIe controller driver: - Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár) - Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár) - Downgrade PIO Response Status messages to debug level (Marek Behún) - Preserve CRS SV (Config Request Retry Software Visibility) bit in emulated Root Control register (Pali Rohár) - Fix issue in configuring reference clock (Pali Rohár) - Don't clear status bits for masked interrupts (Pali Rohár) - Don't mask unused interrupts (Pali Rohár) - Avoid code repetition in advk_pcie_rd_conf() (Marek Behún) - Retry config accesses on CRS response (Pali Rohár) - Simplify emulated Root Capabilities initialization (Pali Rohár) - Fix several link training issues (Pali Rohár) - Fix link-up checking via LTSSM (Pali Rohár) - Fix reporting of Data Link Layer Link Active (Pali Rohár) - Fix emulation of W1C bits (Marek Behún) - Fix MSI domain .alloc() method to return zero on success (Marek Behún) - Read entire 16-bit MSI vector in MSI handler, not just low 8 bits (Marek Behún) - Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits at startup; PCI core will set those as necessary (Pali Rohár) - When operating as a Root Port, set class code to "PCI Bridge" instead of the default "Mass Storage Controller" (Pali Rohár) - Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't implement this per spec (Pali Rohár) - Add emulation of option ROM BAR since aardvark doesn't implement this per spec (Pali Rohár) MediaTek MT7621 PCIe controller driver: - Add MediaTek MT7621 PCIe host controller driver and DT binding (Sergio Paracuellos) Qualcomm PCIe controller driver: - Add SC8180x compatible string (Bjorn Andersson) - Add endpoint controller driver and DT binding (Manivannan Sadhasivam) - Restructure to use of_device_get_match_data() (Prasad Malisetty) - Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty) Renesas R-Car PCIe controller driver: - Remove unnecessary includes (Geert Uytterhoeven) Rockchip DesignWare PCIe controller driver: - Add DT binding (Simon Xue) Socionext UniPhier Pro5 controller driver: - Serialize INTx masking/unmasking (Kunihiko Hayashi) Synopsys DesignWare PCIe controller driver: - Run dwc .host_init() method before registering MSI interrupt handler so we can deal with pending interrupts left by bootloader (Bjorn Andersson) - Clean up Kconfig dependencies (Andy Shevchenko) - Export symbols to allow more modular drivers (Luca Ceresoli) TI DRA7xx PCIe controller driver: - Allow host and endpoint drivers to be modules (Luca Ceresoli) - Enable external clock if present (Luca Ceresoli) TI J721E PCIe driver: - Disable PHY when probe fails after initializing it (Christophe JAILLET) MicroSemi Switchtec management driver: - Return error to application when command execution fails because an out-of-band reset has cleared the device BARs, Memory Space Enable, etc (Kelvin Cao) - Fix MRPC error status handling issue (Kelvin Cao) - Mask out other bits when reading of management VEP instance ID (Kelvin Cao) - Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions (Kelvin Cao) - Add check of event support (Logan Gunthorpe) Miscellaneous: - Remove unused pci_pool wrappers, which have been replaced by dma_pool (Cai Huoqing) - Use 'unsigned int' instead of bare 'unsigned' (Krzysztof Wilczyński) - Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof Wilczyński) - Fix some sscanf(), sprintf() format mismatches (Krzysztof Wilczyński) - Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński) - Correct some misspellings (Krzysztof Wilczyński)" * tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits) PCI: Add ACS quirk for Pericom PI7C9X2G switches PCI: apple: Configure RID to SID mapper on device addition iommu/dart: Exclude MSI doorbell from PCIe device IOVA range PCI: apple: Implement MSI support PCI: apple: Add INTx and per-port interrupt support PCI: kirin: Allow removing the driver PCI: kirin: De-init the dwc driver PCI: kirin: Disable clkreq during poweroff sequence PCI: kirin: Move the power-off code to a common routine PCI: kirin: Add power_off support for Kirin 960 PHY PCI: kirin: Allow building it as a module PCI: kirin: Add MODULE_* macros PCI: kirin: Add Kirin 970 compatible PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge PCI: apple: Set up reference clocks when probing PCI: apple: Add initial hardware bring-up PCI: of: Allow matching of an interrupt-map local to a PCI device of/irq: Allow matching of an interrupt-map local to an interrupt controller irqdomain: Make of_phandle_args_to_fwspec() generally available PCI: Do not enable AtomicOps on VFs ...
| * bcma: simplify reference to driver nameUwe Kleine-König2021-10-131-5/+1
| | | | | | | | | | | | | | | | | | | | | | When bcma_host_pci_probe() is called, the PCI driver core has already assigned the device's driver in local_pci_probe(). So dev->driver is always true, and here it points to bcma_pci_bridge_driver, which has .name set to "bcma-pci-bridge". Simplify accordingly. Link: https://lore.kernel.org/r/20211004125935.2300113-5-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* | bcma: drop unneeded initialization valueSohaib Mohamed2021-10-051-1/+1
|/ | | | | | | | | Do not initialise statics to 0 ERROR found by checkpatch.pl Signed-off-by: Sohaib Mohamed <sohaib.amhmd@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210930194920.15847-1-sohaib.amhmd@gmail.com
* Merge tag 'driver-core-5.15-rc1' of ↵Linus Torvalds2021-09-011-4/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the big set of driver core patches for 5.15-rc1. These do change a number of different things across different subsystems, and because of that, there were 2 stable tags created that might have already come into your tree from different pulls that did the following - changed the bus remove callback to return void - sysfs iomem_get_mapping rework Other than those two things, there's only a few small things in here: - kernfs performance improvements for huge numbers of sysfs users at once - tiny api cleanups - other minor changes All of these have been in linux-next for a while with no reported problems, other than the before-mentioned merge issue" * tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits) MAINTAINERS: Add dri-devel for component.[hc] driver core: platform: Remove platform_device_add_properties() ARM: tegra: paz00: Handle device properties with software node API bitmap: extend comment to bitmap_print_bitmask/list_to_buf drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI topology: use bin_attribute to break the size limitation of cpumap ABI lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list sysfs: Rename struct bin_attribute member to f_mapping sysfs: Invoke iomem_get_mapping() from the sysfs open callback debugfs: Return error during {full/open}_proxy_open() on rmmod zorro: Drop useless (and hardly used) .driver member in struct zorro_dev zorro: Simplify remove callback sh: superhyway: Simplify check in remove callback nubus: Simplify check in remove callback nubus: Make struct nubus_driver::remove return void kernfs: dont call d_splice_alias() under kernfs node lock kernfs: use i_lock to protect concurrent inode updates kernfs: switch kernfs to use an rwsem kernfs: use VFS negative dentry caching ...
| * bus: Make remove callback return voidUwe Kleine-König2021-07-211-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver core ignores the return value of this callback because there is only little it can do when a device disappears. This is the final bit of a long lasting cleanup quest where several buses were converted to also return void from their remove callback. Additionally some resource leaks were fixed that were caused by drivers returning an error code in the expectation that the driver won't go away. With struct bus_type::remove returning void it's prevented that newly implemented buses return an ignored error code and so don't anticipate wrong expectations for driver authors. Reviewed-by: Tom Rix <trix@redhat.com> (For fpga) Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio) Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts) Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb) Acked-by: Pali Rohár <pali@kernel.org> Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media) Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform) Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-By: Vinod Koul <vkoul@kernel.org> Acked-by: Juergen Gross <jgross@suse.com> (For xen) Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd) Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb) Acked-by: Johan Hovold <johan@kernel.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus) Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio) Acked-by: Maximilian Luz <luzmaximilian@gmail.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec) Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack) Acked-by: Geoff Levand <geoff@infradead.org> (For ps3) Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt) Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th) Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia) Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI) Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr) Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid) Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM) Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa) Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire) Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid) Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox) Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss) Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC) Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C Acked-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Finn Thain <fthain@linux-m68k.org> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | bcma: Drop the unused parameter of bcma_scan_read32()Zenghui Yu2021-08-291-4/+3
| | | | | | | | | | | | | | | | | | As it had never been used since the initial commit 8369ae33b705 ("bcma: add Broadcom specific AMBA bus driver"). Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210727025232.663-3-yuzenghui@huawei.com
* | bcma: Fix memory leak for internally-handled coresZenghui Yu2021-08-291-3/+3
|/ | | | | | | | | | | | | | | | | kmemleak reported that dev_name() of internally-handled cores were leaked on driver unbinding. Let's use device_initialize() to take refcounts for them and put_device() to properly free the related stuff. While looking at it, there's another potential issue for those which should be *registered* into driver core. If device_register() failed, we put device once and freed bcma_device structures. In bcma_unregister_cores(), they're treated as unregistered and we hit both UAF and double-free. That smells not good and has also been fixed now. Fixes: ab54bc8460b5 ("bcma: fill core details for every device") Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210727025232.663-2-yuzenghui@huawei.com
* bcma: remove unused functionJiapeng Chong2021-04-181-7/+0
| | | | | | | | | | | | Fix the following clang warning: drivers/bcma/driver_mips.c:55:20: warning: unused function 'mips_write32' [-Wunused-function]. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1618382354-866-1-git-send-email-jiapeng.chong@linux.alibaba.com
* bcma: use semicolons rather than commas to separate statementsJulia Lawall2020-10-011-2/+2
| | | | | | | | | | | | | | | | | | Replace commas with semicolons. What is done is essentially described by the following Coccinelle semantic patch (http://coccinelle.lip6.fr/): // <smpl> @@ expression e1,e2; @@ e1 -, +; e2 ... when any // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1601233948-11629-6-git-send-email-Julia.Lawall@inria.fr
* bcma: gpio: Use irqchip templateLinus Walleij2020-08-021-12/+11
| | | | | | | | | | | | | | This makes the driver use the irqchip template to assign properties to the gpio_irq_chip instead of using the explicit call to gpiochip_irqchip_add(). The irqchip is instead added while adding the gpiochip. Cc: Rafał Miłecki <rafal@milecki.pl> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200722111725.210923-1-linus.walleij@linaro.org
* drivers: bcma: remove set but not used variable `addrh` and `sizeh`Zheng Yongjun2020-08-021-5/+3
| | | | | | | | | | | | Fixes gcc '-Wunused-but-set-variable' warning: drivers/bcma/scan.c: In function 'bcma_erom_get_addr_desc': drivers/bcma/scan.c:219 warning: variable `addrh` and `sizeh` set but not used [-Wunused-but-set-variable] Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200721083935.13306-1-zhengyongjun3@huawei.com
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds2020-01-291-5/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Add WireGuard 2) Add HE and TWT support to ath11k driver, from John Crispin. 3) Add ESP in TCP encapsulation support, from Sabrina Dubroca. 4) Add variable window congestion control to TIPC, from Jon Maloy. 5) Add BCM84881 PHY driver, from Russell King. 6) Start adding netlink support for ethtool operations, from Michal Kubecek. 7) Add XDP drop and TX action support to ena driver, from Sameeh Jubran. 8) Add new ipv4 route notifications so that mlxsw driver does not have to handle identical routes itself. From Ido Schimmel. 9) Add BPF dynamic program extensions, from Alexei Starovoitov. 10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes. 11) Add support for macsec HW offloading, from Antoine Tenart. 12) Add initial support for MPTCP protocol, from Christoph Paasch, Matthieu Baerts, Florian Westphal, Peter Krystad, and many others. 13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu Cherian, and others. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits) net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC udp: segment looped gso packets correctly netem: change mailing list qed: FW 8.42.2.0 debug features qed: rt init valid initialization changed qed: Debug feature: ilt and mdump qed: FW 8.42.2.0 Add fw overlay feature qed: FW 8.42.2.0 HSI changes qed: FW 8.42.2.0 iscsi/fcoe changes qed: Add abstraction for different hsi values per chip qed: FW 8.42.2.0 Additional ll2 type qed: Use dmae to write to widebus registers in fw_funcs qed: FW 8.42.2.0 Parser offsets modified qed: FW 8.42.2.0 Queue Manager changes qed: FW 8.42.2.0 Expose new registers and change windows qed: FW 8.42.2.0 Internal ram offsets modifications MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver Documentation: net: octeontx2: Add RVU HW and drivers overview octeontx2-pf: ethtool RSS config support octeontx2-pf: Add basic ethtool support ...
| * bcma: remove set but not used variable 'sizel'yu kuai2019-12-181-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes gcc '-Wunused-but-set-variable' warning: drivers/bcma/scan.c: In function ‘bcma_erom_get_addr_desc’: drivers/bcma/scan.c:222:20: warning: variable ‘sizel’ set but not used [-Wunused-but-set-variable] It is never used, and so can be removed. Fixes: 8369ae33b705 ("bcma: add Broadcom specific AMBA bus driver") Signed-off-by: yu kuai <yukuai3@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | remove ioremap_nocache and devm_ioremap_nocacheChristoph Hellwig2020-01-064-8/+8
|/ | | | | | | | ioremap has provided non-cached semantics by default since the Linux 2.6 days, so remove the additional ioremap_nocache interface. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Arnd Bergmann <arnd@arndb.de>
* bcma: fix block comment styleYadav Lamichhane2019-10-241-8/+16
| | | | | | | Fix a coding style issue. Signed-off-by: Yadav Lamichhane <tuxomega1@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: make arrays pwr_info_offset and sprom_sizes static const, shrinks ↵Colin Ian King2019-09-131-4/+6
| | | | | | | | | | | | | | | | | | | | object size Arrays pwr_info_offset and sprom_sizes can be make static const rather than populating them on the stack. Shrinks object size by 236 bytes. Before: text data bss dec hex filename 11300 1320 64 12684 318c drivers/bcma/sprom.o After: text data bss dec hex filename 10904 1480 64 12448 30a0 drivers/bcma/sprom.o (gcc version 9.2.1, amd64) Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: fix incorrect update of BCMA_CORE_PCI_MDIO_DATAColin Ian King2019-09-031-2/+2
| | | | | | | | | | | | An earlier commit re-worked the setting of the bitmask and is now assigning v with some bit flags rather than bitwise or-ing them into v, consequently the earlier bit-settings of v are being lost. Fix this by replacing an assignment with the bitwise or instead. Addresses-Coverity: ("Unused value") Fixes: 2be25cac8402 ("bcma: add constants for PCI and use them") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: remove two unused variablesYueHaibing2019-09-031-16/+0
| | | | | | | | | | | | | drivers/bcma/driver_mips.c:70:18: warning: ipsflag_irq_shift defined but not used [-Wunused-const-variable=] drivers/bcma/driver_mips.c:62:18: warning: ipsflag_irq_mask defined but not used [-Wunused-const-variable=] They are never used, so can be removed. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: Use dev_get_drvdataChuhong Yuan2019-08-061-4/+2
| | | | | | | | Instead of using to_pci_dev + pci_get_drvdata, use dev_get_drvdata to make code simpler. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: use dev_* printing functionsRafał Miłecki2019-01-101-4/+4
| | | | | | | It provides more meaningful messages. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: keep a direct pointer to the struct deviceRafał Miłecki2019-01-105-39/+15
| | | | | | | | | | | Accessing struct device is pretty useful/common so having a direct pointer: 1) Simplifies some code 2) Makes bcma_bus_get_host_dev() unneeded 3) Allows further improvements like using dev_* printing helpers Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: Allow selection of this driver when COMPILE_TEST=yBoris Brezillon2018-07-181-1/+2
| | | | | | | | | | | | | | This allows us to increase compile-test coverage without having to build a kernel for MIPS. That's particularly interesting for subsystem maintainers that want to test as many drivers as possible in a single build. We also add a dependency on HAS_IOMEM in BCMA_HOST_SOC to make sure the driver is not selected when the arch does not implement IO accessors. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mappingLinus Torvalds2018-06-041-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull dma-mapping updates from Christoph Hellwig: - replace the force_dma flag with a dma_configure bus method. (Nipun Gupta, although one patch is іncorrectly attributed to me due to a git rebase bug) - use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai) - remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the right thing for bounce buffering. - move dma-debug initialization to common code, and apply a few cleanups to the dma-debug code. - cleanup the Kconfig mess around swiotlb selection - swiotlb comment fixup (Yisheng Xie) - a trivial swiotlb fix. (Dan Carpenter) - support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt) - add a new generic dma-noncoherent dma_map_ops implementation and use it for arc, c6x and nds32. - improve scatterlist validity checking in dma-debug. (Robin Murphy) - add a struct device quirk to limit the dma-mask to 32-bit due to bridge/system issues, and switch x86 to use it instead of a local hack for VIA bridges. - handle devices without a dma_mask more gracefully in the dma-direct code. * tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits) dma-direct: don't crash on device without dma_mask nds32: use generic dma_noncoherent_ops nds32: implement the unmap_sg DMA operation nds32: consolidate DMA cache maintainance routines x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag x86/pci-dma: remove the explicit nodac and allowdac option x86/pci-dma: remove the experimental forcesac boot option Documentation/x86: remove a stray reference to pci-nommu.c core, dma-direct: add a flag 32-bit dma limits dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs dma-debug: check scatterlist segments c6x: use generic dma_noncoherent_ops arc: use generic dma_noncoherent_ops arc: fix arc_dma_{map,unmap}_page arc: fix arc_dma_sync_sg_for_{cpu,device} arc: simplify arc_dma_sync_single_for_{cpu,device} dma-mapping: provide a generic dma-noncoherent implementation dma-mapping: simplify Kconfig dependencies riscv: add swiotlb support riscv: only enable ZONE_DMA32 for 64-bit ...
| * drivers: remove force dma flag from busesChristoph Hellwig2018-05-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | With each bus implementing its own DMA configuration callback, there is no need for bus to explicitly set the force_dma flag. Modify the of_dma_configure function to accept an input parameter which specifies if implicit DMA configuration is required when it is not described by the firmware. Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts Reviewed-by: Rob Herring <robh@kernel.org> [hch: tweaked the changelog a bit] Signed-off-by: Christoph Hellwig <hch@lst.de>
* | bcma: fix buffer size caused crash in bcma_core_mips_print_irq()Rafał Miłecki2018-05-121-1/+1
|/ | | | | | | | | | | | | | | Used buffer wasn't big enough to hold whole strings. Example output of this function is: [ 0.180892] bcma: bus0: core 0x0800, irq: 2(S)* 3 4 5 6 D I [ 0.180948] bcma: bus0: core 0x0812, irq: 2(S) 3* 4 5 6 D I [ 0.180998] bcma: bus0: core 0x082d, irq: 2(S) 3 4* 5 6 D I [ 0.181046] bcma: bus0: core 0x082c, irq: 2(S) 3 4 5 6 D I* which means we need to store up to 24 chars. Fixes: 758f7e06063a8 ("bcma: Use bcma_debug and not pr_cont in MIPS driver") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Cc: stable@vger.kernel.org # v4.15+ Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: Prevent build of PCI host features in moduleMatt Redfearn2018-03-131-1/+1
| | | | | | | | | | | | | | | Attempting to build bcma.ko with BCMA_DRIVER_PCI_HOSTMODE=y results in a build error due to use of symbols not exported from vmlinux: ERROR: "pcibios_enable_device" [drivers/bcma/bcma.ko] undefined! ERROR: "register_pci_controller" [drivers/bcma/bcma.ko] undefined! make[1]: *** [scripts/Makefile.modpost:92: __modpost] Error 1 To prevent this, don't allow the host mode feature to be built if CONFIG_BCMA=m Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: add HP Stream NotebookDenis 'GNUtoo' Carikli2018-02-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In this laptop we have the following PCI device: 02:00.0 Network controller [0280]: Broadcom Limited BCM43142 802.11b/g/n [14e4:4365] (rev 01) Subsystem: Hewlett-Packard Company BCM43142 802.11b/g/n [103c:804a] [...] Region 0: Memory at 91000000 (64-bit, non-prefetchable) [size=32K] [...] With this patch, we can now see its WiFi chip: bcma: bus0: Found chip with id 43142, rev 0x01 and package 0x08 bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x28, class 0x0) bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x21, class 0x0) bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x16, class 0x0) bcma: bus0: Core 3 found: UNKNOWN (manuf 0x43B, id 0x368, rev 0x00, class 0x0) bcma: bus0: Found rev 15 PMU (capabilities 0x518C5E0F) bcma: bus0: SPROM offset 0x840 bcma: bus0: Found SPROM revision 10 bcma: bus0: Workarounds unknown or not needed for device 0xA886 bcma: bus0: Bus registered But it not yet supported by brcmsmac so it won't work for now: brcmsmac bcma0:1: brcms_b_attach wl0: vendor 0x14e4 device 0x4365 brcmsmac: unknown device id 4365 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: Replace mdelay with usleep_range in bcma_pmu_resources_initJia-Ju Bai2018-02-271-1/+1
| | | | | | | | | | | | | After checking all possible call chains to bcma_pmu_resources_init() here, my tool finds that this function is never called in atomic context, namely never in an interrupt handler or holding a spinlock. Thus mdelay can be replaced with usleep_range to avoid busy wait. This is found by a static analysis tool named DCNS written by myself. Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-01-201-1/+1
|\ | | | | | | | | | | | | | | | | | | | | The BPF verifier conflict was some minor contextual issue. The TUN conflict was less trivial. Cong Wang fixed a memory leak of tfile->tx_array in 'net'. This is an skb_array. But meanwhile in net-next tun changed tfile->tx_arry into tfile->tx_ring which is a ptr_ring. Signed-off-by: David S. Miller <davem@davemloft.net>
| * bcma: Fix 'allmodconfig' and BCMA builds on MIPS targetsGuenter Roeck2018-01-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mips builds with BCMA host mode enabled fail in mainline and -next with: In file included from include/linux/bcma/bcma.h:10:0, from drivers/bcma/bcma_private.h:9, from drivers/bcma/main.c:8: include/linux/bcma/bcma_driver_pci.h:218:24: error: field 'pci_controller' has incomplete type Bisect points to commit d41e6858ba58c ("MIPS: Kconfig: Set default MIPS system type as generic") as the culprit. Analysis shows that the commmit changes PCI configuration and enables PCI_DRIVERS_GENERIC. This in turn disables PCI_DRIVERS_LEGACY. 'struct pci_controller' is, however, only defined if PCI_DRIVERS_LEGACY is enabled. Ultimately that means that BCMA_DRIVER_PCI_HOSTMODE depends on PCI_DRIVERS_LEGACY. Add the missing dependency. Fixes: d41e6858ba58c ("MIPS: Kconfig: Set default MIPS system type as ...") Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: James Hogan <jhogan@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: James Hogan <jhogan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | bcma: Adjust block commentAshish Kalra2017-12-071-1/+2
|/ | | | | | | | | | | use * for block comments in multiple lines according to kernel coding style Reported by: checkpatch.pl Signed-off-by: Ashish Kalra <eashishkalra@gmail.com> Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds2017-11-152-13/+17
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: "Highlights: 1) Maintain the TCP retransmit queue using an rbtree, with 1GB windows at 100Gb this really has become necessary. From Eric Dumazet. 2) Multi-program support for cgroup+bpf, from Alexei Starovoitov. 3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew Lunn. 4) Add meter action support to openvswitch, from Andy Zhou. 5) Add a data meta pointer for BPF accessible packets, from Daniel Borkmann. 6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet. 7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli. 8) More work to move the RTNL mutex down, from Florian Westphal. 9) Add 'bpftool' utility, to help with bpf program introspection. From Jakub Kicinski. 10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper Dangaard Brouer. 11) Support 'blocks' of transformations in the packet scheduler which can span multiple network devices, from Jiri Pirko. 12) TC flower offload support in cxgb4, from Kumar Sanghvi. 13) Priority based stream scheduler for SCTP, from Marcelo Ricardo Leitner. 14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg. 15) Add RED qdisc offloadability, and use it in mlxsw driver. From Nogah Frankel. 16) eBPF based device controller for cgroup v2, from Roman Gushchin. 17) Add some fundamental tracepoints for TCP, from Song Liu. 18) Remove garbage collection from ipv6 route layer, this is a significant accomplishment. From Wei Wang. 19) Add multicast route offload support to mlxsw, from Yotam Gigi" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits) tcp: highest_sack fix geneve: fix fill_info when link down bpf: fix lockdep splat net: cdc_ncm: GetNtbFormat endian fix openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start netem: remove unnecessary 64 bit modulus netem: use 64 bit divide by rate tcp: Namespace-ify sysctl_tcp_default_congestion_control net: Protect iterations over net::fib_notifier_ops in fib_seq_sum() ipv6: set all.accept_dad to 0 by default uapi: fix linux/tls.h userspace compilation error usbnet: ipheth: prevent TX queue timeouts when device not ready vhost_net: conditionally enable tx polling uapi: fix linux/rxrpc.h userspace compilation errors net: stmmac: fix LPI transitioning for dwmac4 atm: horizon: Fix irq release error net-sysfs: trigger netlink notification on ifalias change via sysfs openvswitch: Using kfree_rcu() to simplify the code openvswitch: Make local function ovs_nsh_key_attr_size() static openvswitch: Fix return value check in ovs_meter_cmd_features() ...
| * Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of ↵David S. Miller2017-11-041-4/+7
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.15 Mostly fixes this time, but also few new features. Major changes: wil6210 * remove ssid debugfs file rsi * add WOWLAN support for suspend, hibernate and shutdown states ath10k * add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware where it's supported (QCA99x0 and QCA4019) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| | * bcma: Use bcma_debug and not pr_cont in MIPS driverJoe Perches2017-10-271-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 66cc04424960 ("bcma: use bcma_debug and pr_cont in MIPS driver") converted a printk(KERN_DEBUG to bcma_debug. bcma_debug is guarded by a #define DEBUG via pr_debug. This means that the bcma_debug will generally not be emitted but any pr_cont following the bcma_debug will be emitted. Correct this by removing the uses of pr_cont by using a temporary. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-11-044-0/+4
| |\ \ | | |/ | |/| | | | | | | | | | | | | Files removed in 'net-next' had their license header updated in 'net'. We take the remove from 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | bcma: use bcma_debug and pr_cont in MIPS driverRafał Miłecki2017-10-171-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | Using bcma_debug gives a device-specific prefix for messages and pr_cont is a common helper for continuing a line. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-By: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | bcma: keep *config menu togetherRandy Dunlap2017-10-131-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use "if BCMA"/"endif" around all Kconfig symbols so that they are kept together in *config menus instead of showing up in unexpected places. Also remove "depends on BCMA" since this is handled by the "if BCMA" addition. Tested with ARCH={x86_64,MIPS} using make {n,menu,g,x}config. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | | Merge tag 'gpio-v4.15-1' of ↵Linus Torvalds2017-11-151-1/+1
|\ \ \ | |_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v4.15 kernel cycle: Core: - Fix the semantics of raw GPIO to actually be raw. No inversion semantics as before, but also no open draining, and allow the raw operations to affect lines used for interrupts as the caller supposedly knows what they are doing if they are getting the big hammer. - Rewrote the __inner_function() notation calls to names that make more sense. I just find this kind of code disturbing. - Drop the .irq_base() field from the gpiochip since now all IRQs are mapped dynamically. This is nice. - Support for .get_multiple() in the core driver API. This allows us to read several GPIO lines with a single register read. This has high value for some usecases: it can be used to create oscilloscopes and signal analyzers and other things that rely on reading several lines at exactly the same instant. Also a generally nice optimization. This uses the new assign_bit() macro from the bitops lib that was ACKed by Andrew Morton and is implemented for two drivers, one of them being the generic MMIO driver so everyone using that will be able to benefit from this. - Do not allow requests of Open Drain and Open Source setting of a GPIO line simultaneously. If the hardware actually supports enabling both at the same time the electrical result would be disastrous. - A new interrupt chip core helper. This will be helpful to deal with "banked" GPIOs, which means GPIO controllers with several logical blocks of GPIO inside them. This is several gpiochips per device in the device model, in contrast to the case when there is a 1-to-1 relationship between a device and a gpiochip. New drivers: - Maxim MAX3191x industrial serializer, a very interesting piece of professional I/O hardware. - Uniphier GPIO driver. This is the GPIO block from the recent Socionext (ex Fujitsu and Panasonic) platform. - Tegra 186 driver. This is based on the new banked GPIO infrastructure. Other improvements: - Some documentation improvements. - Wakeup support for the DesignWare DWAPB GPIO controller. - Reset line support on the DesignWare DWAPB GPIO controller. - Several non-critical bug fixes and improvements for the Broadcom BRCMSTB driver. - Misc non-critical bug fixes like exotic errorpaths, removal of dead code etc. - Explicit comments on fall-through switch() statements" * tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits) gpio: tegra186: Remove tegra186_gpio_lock_class gpio: rcar: Add r8a77995 (R-Car D3) support pinctrl: bcm2835: Fix some merge fallout gpio: Fix undefined lock_dep_class gpio: Automatically add lockdep keys gpio: Introduce struct gpio_irq_chip.first gpio: Disambiguate struct gpio_irq_chip.nested gpio: Add Tegra186 support gpio: Export gpiochip_irq_{map,unmap}() gpio: Implement tighter IRQ chip integration gpio: Move lock_key into struct gpio_irq_chip gpio: Move irq_valid_mask into struct gpio_irq_chip gpio: Move irq_nested into struct gpio_irq_chip gpio: Move irq_chained_parent to struct gpio_irq_chip gpio: Move irq_default_type to struct gpio_irq_chip gpio: Move irq_handler to struct gpio_irq_chip gpio: Move irqdomain into struct gpio_irq_chip gpio: Move irqchip into struct gpio_irq_chip gpio: Introduce struct gpio_irq_chip pinctrl: armada-37xx: remove unused variable ...
| * | gpio: Move irqdomain into struct gpio_irq_chipThierry Reding2017-11-081-1/+1
| |/ | | | | | | | | | | | | | | | | In order to consolidate the multiple ways to associate an IRQ chip with a GPIO chip, move more fields into the new struct gpio_irq_chip. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* / License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-024-0/+4
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* bcma: make BCMA a menuconfig to ease disabling it allVincent Legoll2017-08-081-7/+2
| | | | | | | No need to get into the submenu to disable all BCMA-related config entries. Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: gpio: Correct number of GPIOs for BCM53573Florian Fainelli2017-07-271-0/+1
| | | | | | | | Broadcom BCM53573 SoCs actually have 32 GPIOs, and not 16. Fixes: 3f37ec79dd21 ("bcma: support BCM53573 series of wireless SoCs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: fill core OF info independently of bus typeRafał Miłecki2017-03-201-2/+2
| | | | | | | | | PCI devices can be described in DT as well so we should always execute relevant code. This will make bcma e.g. set of_node for cores described in DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: use helper function to set core dev's parentRafał Miłecki2017-03-201-2/+1
| | | | | | | A tiny code deduplication thanks to the bcma_bus_get_host_dev. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: drop unneeded check for CONFIG_OF_IRQRafał Miłecki2017-03-201-3/+0
| | | | | | | | | | | | | We already have the same check in bcma_of_get_irq which really calls symbols available with CONFIG_OF_IRQ only. It appears this duplicated check was accidentally added in commit c58d900cc96a ("bcma: fix building without OF_IRQ"). The rest of code in bcma_of_fill_device should work fine without CONFIG_OF_IRQ. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Cc: Arnd Bergmann <arnd@arndb.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bcma: gpio: set of_node regardless of the host typeRafał Miłecki2017-03-081-2/+1
| | | | | | | | | | DT allows describing many device types, not only platform ones. If e.g. bcma is hosted on PCI(e) and it has its of_node, let's pass it to the GPIO subsystem. This allows GPIO code to handle more hardware details not only for bcma on a SoC. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-28 13:30:30 +0100