summaryrefslogtreecommitdiffstats
path: root/drivers/clk/at91 (follow)
Commit message (Collapse)AuthorAgeFilesLines
* clk: at91: sama7g5: set low limit for mck0 at 32KHzClaudiu Beznea2021-10-271-1/+1
| | | | | | | | | MCK0 could go as low as 32KHz. Set this limit. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-15-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: remove prescaler part of master clockClaudiu Beznea2021-10-271-10/+1
| | | | | | | | | | | | | | | | | | On SAMA7G5 the prescaler part of master clock has been implemented as a changeable one. Everytime the prescaler is changed the PMC_SR.MCKRDY bit must be polled. Value 1 for PMC_SR.MCKRDY means the prescaler update is done. Driver polls for this bit until it becomes 1. On SAMA7G5 it has been discovered that in some conditions the PMC_SR.MCKRDY is not rising but the rate it provides it's stable. The workaround is to add a timeout when polling for PMC_SR.MCKRDY. At the moment, for SAMA7G5, the prescaler will be removed from Linux clock tree as all the frequencies for CPU could be obtained from PLL and also there will be less overhead when changing frequency via DVFS. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-14-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: add notifier for dividerClaudiu Beznea2021-10-2713-82/+186
| | | | | | | | | | | | | | | | | | | | | SAMA7G5 supports DVFS by changing cpuck. On SAMA7G5 mck0 shares the same parent with cpuck as seen in the following clock tree: +----------> cpuck | FRAC PLL ---> DIV PLL -+-> DIV ---> mck0 mck0 could go b/w 32KHz and 200MHz on SAMA7G5. To avoid mck0 overclocking while changing FRAC PLL or DIV PLL the commit implements a notifier for mck0 which applies a safe divider to register (maximum value of the divider which is 5) on PRE_RATE_CHANGE events (such that changes on PLL to not overclock mck0) and sets the maximum allowed rate on POST_RATE_CHANGE events. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-13-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-sam9x60-pll: add notifier for div part of PLLClaudiu Beznea2021-10-274-29/+95
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SAM9X60's PLL which is also part of SAMA7G5 is composed of 2 parts: one fractional part and one divider. On SAMA7G5 the CPU PLL could be changed at run-time to implement DVFS. The hardware clock tree on SAMA7G5 for CPU PLL is as follows: +---- div1 ----------------> cpuck | FRAC PLL ---> DIV PLL -+-> prescaler ---> div0 ---> mck0 The div1 block is not implemented in Linux; on prescaler block it has been discovered a bug on some scenarios and will be removed from Linux in next commits. Thus, the final clock tree that will be used in Linux will be as follows: +-----------> cpuck | FRAC PLL ---> DIV PLL -+-> div0 ---> mck0 It has been proposed in [1] to not introduce a new CPUFreq driver but to overload the proper clock drivers with proper operation such that cpufreq-dt to be used. To accomplish this DIV PLL and div0 implement clock notifiers which applies safe dividers before FRAC PLL is changed. The current commit treats only the DIV PLL by adding a notifier that sets a safe divider on PRE_RATE_CHANGE events. The safe divider is provided by initialization clock code (sama7g5.c). The div0 is treated in next commits (to keep the changes as clean as possible). [1] https://lore.kernel.org/lkml/20210105104426.4tmgc2l3vyicwedd@vireshk-i7/ Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-12-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: fix prescaler logicClaudiu Beznea2021-10-271-1/+1
| | | | | | | | | | | | When prescaler value read from register is MASTER_PRES_MAX it means that the input clock will be divided by 3. Fix the code to reflect this. Fixes: 7a110b9107ed8 ("clk: at91: clk-master: re-factor master clock") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-11-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: mask mckr against layout->maskClaudiu Beznea2021-10-271-2/+5
| | | | | | | | | | Mask values read/written from/to MCKR against layout->mask as this mask may be different b/w PMC versions. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-10-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: check if div or pres is zeroClaudiu Beznea2021-10-271-2/+2
| | | | | | | | | | | | | Check if div or pres is zero before using it as argument for ffs(). In case div is zero ffs() will return 0 and thus substracting from zero will lead to invalid values to be setup in registers. Fixes: 7a110b9107ed8 ("clk: at91: clk-master: re-factor master clock") Fixes: 75c88143f3b87 ("clk: at91: clk-master: add master clock support for SAMA7G5") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-9-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULLClaudiu Beznea2021-10-271-2/+2
| | | | | | | | | | | | Use DIV_ROUND_CLOSEST_ULL() to avoid any inconsistency b/w the rate computed in sam9x60_frac_pll_recalc_rate() and the one computed in sam9x60_frac_pll_compute_mul_frac(). Fixes: 43b1bb4a9b3e1 ("clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-8-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: pmc: add sama7g5 to the list of available pmcsClaudiu Beznea2021-10-271-2/+3
| | | | | | | | | | Add SAMA7G5 to the list of available PMCs such that the suspend/resume code for clocks to be used on backup mode. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-7-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: improve readability by using local variablesClaudiu Beznea2021-10-271-3/+3
| | | | | | | | | | | Improve readability in clk_sama7g5_master_set() by using local variables. Suggested-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-6-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: add register definition for sama7g5's master clockClaudiu Beznea2021-10-271-27/+23
| | | | | | | | | | | | | | | | | | | | SAMA7G5 has 4 master clocks (MCK1..4) which are controlled though the register at offset 0x30 (relative to PMC). In the last/first phase of suspend/resume procedure (which is architecture specific) the parent of master clocks are changed (via assembly code) for more power saving (see file arch/arm/mach-at91/pm_suspend.S, macros at91_mckx_ps_enable and at91_mckx_ps_restore). Thus the macros corresponding to register at offset 0x30 need to be shared b/w clk-master.c and pm_suspend.S. commit ec03f18cc222 ("clk: at91: add register definition for sama7g5's master clock") introduced the proper macros but didn't adapted the clk-master.c as well. Thus, this commit adapt the clk-master.c to use the macros introduced in commit ec03f18cc222 ("clk: at91: add register definition for sama7g5's master clock"). Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-5-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: add securam's peripheral clockClaudiu Beznea2021-10-271-0/+1
| | | | | | | | | Add SECURAM's peripheral clock. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-4-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: pmc: execute suspend/resume only for backup modeClaudiu Beznea2021-10-271-0/+39
| | | | | | | | | | | | | Before going to backup mode architecture specific PM code sets the first word in securam (file arch/arm/mach-at91/pm.c, function at91_pm_begin()). Thus take this into account when suspending/resuming clocks. This will avoid executing unnecessary instructions when suspending to non backup modes. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-3-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: re-factor clocks suspend/resumeClaudiu Beznea2021-10-2712-181/+558
| | | | | | | | | | | | | | | | | | | | | | | | | SAMA5D2 and SAMA7G5 have a special power saving mode (backup mode) where most of the SoC's components are powered off (including PMC). Resuming from this mode is done with the help of bootloader. Peripherals are not aware of the power saving mode thus most of them are disabling clocks in proper suspend API and re-enable them in resume API without taking into account the previously setup rate. Moreover some of the peripherals are acting as wakeup sources and are not disabling the clocks in this scenario, when suspending. Since backup mode cuts the power for peripherals, in resume part these clocks needs to be re-configured. The initial PMC suspend/resume code was designed only for SAMA5D2's PMC (as it was the only one supporting backup mode). SAMA7G supports also backup mode and its PMC is different (few new functionalities, different registers offsets, different offsets in registers for each functionalities). To address both SAMA5D2 and SAMA7G5 PMC add .save_context()/.resume_context() support to each clocks driver and call this from PMC driver. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20211011112719.3951784-2-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: check pmc node status before registering syscore opsClément Léger2021-10-081-0/+5
| | | | | | | | | | | | | | | | Currently, at91 pmc driver always register the syscore_ops whatever the status of the pmc node that has been found. When set as secure and disabled, the pmc should not be accessed or this will generate abort exceptions. To avoid this, add a check on node availability before registering the syscore operations. Signed-off-by: Clément Léger <clement.leger@bootlin.com> Link: https://lore.kernel.org/r/20210913082633.110168-1-clement.leger@bootlin.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Fixes: b3b02eac33ed ("clk: at91: Add sama5d2 suspend/resume") Signed-off-by: Stephen Boyd <sboyd@kernel.org>
*-. Merge branches 'clk-kirkwood', 'clk-imx', 'clk-doc', 'clk-zynq' and ↵Stephen Boyd2021-09-021-7/+7
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 'clk-ralink' into clk-next * clk-kirkwood: clk: kirkwood: Fix a clocking boot regression * clk-imx: clk: imx8mn: Add M7 core clock clk: imx8m: fix clock tree update of TF-A managed clocks clk: imx: clk-divider-gate: Switch to clk_divider.determine_rate clk: imx8mn: use correct mux type for clkout path clk: imx8mm: use correct mux type for clkout path * clk-doc: dt-bindings: clock: samsung: fix header path in example MAINTAINERS: clock: include S3C and S5P in Samsung SoC clock entry dt-bindings: clock: samsung: convert S5Pv210 AudSS to dtschema dt-bindings: clock: samsung: convert Exynos AudSS to dtschema dt-bindings: clock: samsung: convert Exynos4 to dtschema dt-bindings: clock: samsung: convert Exynos3250 to dtschema dt-bindings: clock: samsung: convert Exynos542x to dtschema dt-bindings: clock: samsung: add bindings for Exynos external clock dt-bindings: clock: samsung: convert Exynos5250 to dtschema dt-bindings: clock: brcm,iproc-clocks: fix armpll properties clk: zynqmp: Fix kernel-doc format clk: at91: sama7g5: remove all kernel-doc & kernel-doc warnings clk: zynqmp: fix kernel doc * clk-zynq: clk: zynqmp: Fix a memory leak clk: zynqmp: Check the return type * clk-ralink: clk: ralink: avoid to set 'CLK_IS_CRITICAL' flag for gates
| | * clk: at91: sama7g5: remove all kernel-doc & kernel-doc warningsRandy Dunlap2021-08-291-7/+7
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove all "/**" kernel-doc markers from sama7g5.c since they are all internal to this driver source file only. This eliminates 14 warnings that were reported by the kernel test robot. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: linux-clk@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Link: https://lore.kernel.org/r/20210819223237.20115-1-rdunlap@infradead.org Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* / clk: at91: clk-generated: Limit the requested rate to our rangeCodrin Ciubotariu2021-08-291-0/+6
|/ | | | | | | | | | | | On clk_generated_determine_rate(), the requested rate could be outside of clk's range. Limit the rate to the clock's range to not return an error. Fixes: df70aeef6083 ("clk: at91: add generated clock driver") Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20210707131213.3283509-1-codrin.ciubotariu@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: Trivial typo fixes in the file sama7g5.cBhaskar Chowdhury2021-03-131-3/+3
| | | | | | | | | | s/critial/critical/ ......two different places s/parrent/parent/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Link: https://lore.kernel.org/r/20210313053222.14706-1-unixbhaskar@gmail.com Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: Fix the declaration of the clocksTudor Ambarus2021-02-109-28/+28
| | | | | | | | | | | | | | | | | | | | | | These are all "early clocks" that require initialization just at of_clk_init() time. Use CLK_OF_DECLARE() to declare them. This also fixes a problem that was spotted when fw_devlink was set to 'on' by default: the boards failed to boot. The reason is that CLK_OF_DECLARE_DRIVER() clears the OF_POPULATED and causes the consumers of the clock to be postponed by fw_devlink until the second initialization routine of the clock has been completed. One of the consumers of the clock is the timer, which is used as a clocksource, and needs the clock initialized early. Postponing the timers caused the fail at boot. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20210203154332.470587-1-tudor.ambarus@microchip.com Acked-by: Saravana Kannan <saravanak@google.com> Tested-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sam9x60: remove atmel,osc-bypass supportAlexandre Belloni2020-12-201-5/+1
| | | | | | | | | | | | | The sam9x60 doesn't have the MOSCXTBY bit to enable the crystal oscillator bypass. Fixes: 01e2113de9a5 ("clk: at91: add sam9x60 pmc driver") Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201202125816.168618-1-alexandre.belloni@bootlin.com Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: register cpu clockClaudiu Beznea2020-12-191-7/+6
| | | | | | | | | | | | | Register CPU clock as being the master clock prescaler. This would be used by DVFS. The block schema of SAMA7G5's PMC contains also a divider between master clock prescaler and CPU (PMC_CPU_RATIO.RATIO) but the frequencies supported by SAMA7G5 could be directly received from CPUPLL + master clock prescaler and the extra divider would do no work in case it would be enabled. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-12-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: re-factor master clockClaudiu Beznea2020-12-1914-146/+542
| | | | | | | | | | | Re-factor master clock driver by splitting it into 2 clocks: prescaller and divider clocks. Based on registered clock flags the prescaler's rate could be changed at runtime. This is necessary for platforms supporting DVFS (e.g. SAMA7G5) where master clock could be changed at run-time. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-11-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHzClaudiu Beznea2020-12-191-14/+47
| | | | | | | | | | Since CPU PLL feeds both CPU clock and MCK0, MCK0 cannot go higher than 200MHz and MCK0 maximum prescaller is 5 limit the CPU PLL at 1GHz to avoid MCK0 overclocking while CPU PLL is changed by DVFS. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-10-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: decrease lower limit for MCK0 rateClaudiu Beznea2020-12-191-1/+1
| | | | | | | | | | | | On SAMA7G5 CPU clock is changed at run-time by DVFS. Since MCK0 and CPU clock shares the same parent clock (CPUPLL clock) the MCK0 is also changed by DVFS to avoid over/under clocking of MCK0 consumers. The lower limit is changed to be able to set MCK0 accordingly by DVFS. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-9-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: remove mck0 from parent list of other clocksClaudiu Beznea2020-12-191-29/+26
| | | | | | | | | | MCK0 is changed at runtime by DVFS. Due to this, since not all IPs are glitch free aware at MCK0 changes, remove MCK0 from parent list of other clocks (e.g. generic clock, programmable/system clock, MCKX). Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-8-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-sam9x60-pll: allow runtime changes for pllClaudiu Beznea2020-12-194-41/+197
| | | | | | | | | Allow runtime frequency changes for PLLs registered with proper flags. This is necessary for CPU PLL on SAMA7G5 which is used by DVFS. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-7-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristicsEugen Hristev2020-12-191-2/+2
| | | | | | | | | | | This SoC has the 5th divisor for the mck0 master clock. Adapt the characteristics accordingly. Reported-by: Mihai Sain <mihai.sain@microchip.com> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-6-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: add 5th divisor for mck masterEugen Hristev2020-12-192-2/+2
| | | | | | | | | | | | | clk-master can have 5 divisors with a field width of 3 bits on some products. Change the mask and number of divisors accordingly. Reported-by: Mihai Sain <mihai.sain@microchip.com> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-5-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DTEugen Hristev2020-12-191-2/+4
| | | | | | | | | | | | Allow SYSPLL and CPUPLL to be referenced as a PMC_TYPE_CORE clock from phandle in DT. Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> [claudiu.beznea@microchip.com: adapt commit message, add CPU PLL] Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-4-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* dt-bindings: clock: at91: add sama7g5 pll definesEugen Hristev2020-12-191-3/+3
| | | | | | | | | | | | Add SAMA7G5 specific PLL defines to be referenced in a phandle as a PMC_TYPE_CORE clock. Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> [claudiu.beznea@microchip.com: adapt comit message, adapt sama7g5.c] Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-3-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: fix compilation errorClaudiu Beznea2020-12-191-2/+4
| | | | | | | | | | | | | | pmc_data_allocate() has been changed. pmc_data_free() was removed. Adapt the code taking this into consideration. With this the programmable clocks were also saved in sama7g5_pmc so that they could be later referenced. Fixes: cb783bbbcf54 ("clk: at91: sama7g5: add clock support for sama7g5") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-2-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
*-. Merge branches 'clk-ingenic', 'clk-at91', 'clk-kconfig', 'clk-imx', ↵Stephen Boyd2020-10-204-8/+12
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 'clk-qcom', 'clk-prima2' and 'clk-bcm' into clk-next - Support qcom SM8150/SM8250 video and display clks - Change how qcom's display port clks work * clk-ingenic: clk: ingenic: Respect CLK_SET_RATE_PARENT in .round_rate clk: ingenic: Don't tag custom clocks with CLK_SET_RATE_PARENT clk: ingenic: Don't use CLK_SET_RATE_GATE for PLL clk: ingenic: Use readl_poll_timeout instead of custom loop clk: ingenic: Use to_clk_info() macro for all clocks * clk-at91: clk: at91: sam9x60: support only two programmable clocks clk: at91: clk-sam9x60-pll: remove unused variable clk: at91: clk-main: update key before writing AT91_CKGR_MOR clk: at91: remove the checking of parent_name * clk-kconfig: clk: Restrict CLK_HSDK to ARC_SOC_HSDK * clk-imx: clk: imx8mq: Fix usdhc parents order clk: imx: imx21: Remove clock driver clk: imx: gate2: Fix a few typos clk: imx: Fix and update kerneldoc clk: imx: fix i.MX7D peripheral clk mux flags clk: imx: fix composite peripheral flags clk: imx: Correct the memrepair clock on imx8mp clk: imx: Correct the root clk of media ldb on imx8mp clk: imx: vf610: Add CRC clock clk: imx: Explicitly include bits.h clk: imx8qxp: Support building i.MX8QXP clock driver as module clk: imx8m: Support module build clk: imx: Add clock configuration for ARMv7 platforms clk: imx: Support building i.MX common clock driver as module clk: composite: Export clk_hw_register_composite() clk: imx6sl: Use BIT(x) to avoid shifting signed 32-bit value by 31 bits * clk-qcom: clk: qcom: gdsc: Keep RETAIN_FF bit set if gdsc is already on clk: qcom: Add display clock controller driver for SM8150 and SM8250 dt-bindings: clock: add QCOM SM8150 and SM8250 display clock bindings clk: qcom: add video clock controller driver for SM8250 clk: qcom: add video clock controller driver for SM8150 dt-bindings: clock: add SM8250 QCOM video clock bindings dt-bindings: clock: add SM8150 QCOM video clock bindings dt-bindings: clock: combine qcom,sdm845-videocc and qcom,sc7180-videocc clk: qcom: gcc-msm8994: Add missing clocks, resets and GDSCs clk/qcom: fix spelling typo clk: qcom: gcc-sdm660: Fix wrong parent_map clk: qcom: dispcc: Update DP clk ops for phy design clk: qcom: gcc-msm8939: remove defined but not used variables clk: qcom: ipq8074: make pcie0_rchng_clk_src static * clk-prima2: clk: clk-prima2: fix return value check in prima2_clk_init() * clk-bcm: clk: bcm2835: add missing release if devm_clk_hw_register fails clk: bcm: rpi: Add register to control pixel bvb clk
| | * clk: at91: sam9x60: support only two programmable clocksClaudiu Beznea2020-10-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to datasheet (Chapter 29.16.13, PMC Programmable Clock Register) there are only two programmable clocks on SAM9X60. Fixes: 01e2113de9a5 ("clk: at91: add sam9x60 pmc driver") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1602686072-28296-1-git-send-email-claudiu.beznea@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
| | * clk: at91: clk-sam9x60-pll: remove unused variableClaudiu Beznea2020-10-141-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix variable set but not used compilation warning. Fixes: 43b1bb4a9b3e ("clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1598338751-20607-4-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
| | * clk: at91: clk-main: update key before writing AT91_CKGR_MORClaudiu Beznea2020-10-141-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SAMA5D2 datasheet specifies on chapter 33.22.8 (PMC Clock Generator Main Oscillator Register) that writing any value other than 0x37 on KEY field aborts the write operation. Use the key when selecting main clock parent. Fixes: 27cb1c2083373 ("clk: at91: rework main clk implementation") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/1598338751-20607-3-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
| | * clk: at91: remove the checking of parent_nameClaudiu Beznea2020-10-141-2/+2
| |/ | | | | | | | | | | | | | | | | | | | | | | There is no need to check parent_name variable while assigning it to init.parent_names. parent_name variable is already checked at the beginning of at91_clk_register_peripheral() function. Fixes: 6114067e437eb ("clk: at91: add PMC peripheral clocks") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/1598338751-20607-2-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* / clk: at91: drop unused at91sam9g45_pcr_layoutKrzysztof Kozlowski2020-09-221-7/+0
|/ | | | | | | | | | | | The at91sam9g45_pcr_layout is not used so drop it to fix build warning: drivers/clk/at91/at91sam9g45.c:49:36: warning: 'at91sam9g45_pcr_layout' defined but not used [-Wunused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200916161740.14173-1-krzk@kernel.org Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sama7g5: add clock support for sama7g5Claudiu Beznea2020-07-242-0/+1060
| | | | | | | | Add clock support for SAMA7G5. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-19-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-utmi: add utmi support for sama7g5Claudiu Beznea2020-07-242-5/+102
| | | | | | | | | | Add UTMI support for SAMA7G5. SAMA7G5's UTMI control is done via XTALF register. Values written at bits 2..0 in this register correspond to the on board crystal oscillator frequency. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-18-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputsClaudiu Beznea2020-07-243-186/+433
| | | | | | | | | | | | | Some of the SAMA7G5 PLLs support multiple outputs (e.g. AUDIO PLL). For these, split the PLL clock in two: fractional clock and divider clock. In case PLLs supports multiple outputs (since these outputs are dividers (with different settings) sharing the same fractional part), it will register one fractional clock and multiple divider clocks (dividers sharing the fractional clock). Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-17-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-programmable: add mux_table optionClaudiu Beznea2020-07-2413-17/+38
| | | | | | | | | Add mux table option. This is necessary for IP versions that has gaps in the range of available clock sources (e.g. SAMA7G5). Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-15-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-peripheral: add support for changeable parent rateClaudiu Beznea2020-07-249-16/+119
| | | | | | | | | | | Some peripheral clocks on SAMA7G5 supports requesting parent to change its rate (image related clocks: csi, csi2dc, isc). Add support so that if registered with this option the clock rate to be requested from parent. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-14-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-master: add master clock support for SAMA7G5Claudiu Beznea2020-07-242-5/+312
| | | | | | | | | | | Add master clock support (MCK1..4) for SAMA7G5. SAMA7G5's PMC has multiple master clocks feeding different subsystems. One of them feeds image subsystem and is changeable based on image subsystem needs. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-13-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-generated: add mux_table optionClaudiu Beznea2020-07-245-8/+16
| | | | | | | | | Add mux table option. This is necessary for IP versions that has gaps in the range of available clock sources (e.g. SAMA7G5). Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-12-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: clk-generated: pass the id of changeable parent at registrationClaudiu Beznea2020-07-245-35/+37
| | | | | | | | | | | | | | | | | Pass the ID of changeable parent at registration. This will allow the scalability of this clock driver with regards to the changeable parent ID for versions of this IP where changeable parent is not the last one in the parents list (e.g. SAMA7G5). With this the clock flags are set to zero in case we have no changeable parent. Also in clk_generated_best_diff() the *best_diff variable is check against tmp_diff variable using ">=" operator instead of ">" so that in case the requested frequency could be obtained using fix parents + gck dividers but the clock also supports changeable parent to be able to force the usage of the changeable parent. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-11-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: replace conditional operator with double logical notClaudiu Beznea2020-07-245-8/+8
| | | | | | | | | Replace conditional operator with double logical not as code may be simpler to read. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-10-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sckc: register slow_rc with accuracy optionClaudiu Beznea2020-07-241-2/+3
| | | | | | | | | | | | | | Chapter 57.7.5 of SAM9X60 datasheet specifies that the maximum drift of this oscillator is +- 3KHz. Use that value and the formula at [1] or the calculator at [2] to compute the PPB value. [1] https://www.everythingrf.com/rf-calculators/ppm-to-hz-calculator [2] https://www.changpuak.ch/electronics/ppm_to_Hz_converter.php Fixes: 04bcc4275e601 ("clk: at91: sckc: add support for SAM9X60") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-9-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sam9x60: fix main rc oscillator frequencyClaudiu Beznea2020-07-241-1/+1
| | | | | | | | | | | Main RC oscillator frequency is 12MHz according to datasheet (chapter 27.2). Fixes: 01e2113de9a52 ("clk: at91: add sam9x60 pmc driver") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/1595403506-8209-8-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk: at91: sam9x60-pll: use frac when setting frequencyClaudiu Beznea2020-07-241-4/+8
| | | | | | | | | | | | In commit a436c2a447e59 ("clk: at91: add sam9x60 PLL driver") the fractional part of PLL wasn't set on registers but it was calculated and taken into account for determining div and mul (see sam9x60_pll_get_best_div_mul()). Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1595403506-8209-7-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-18 13:21:57 +0100