summaryrefslogtreecommitdiffstats
path: root/drivers/fsi (follow)
Commit message (Collapse)AuthorAgeFilesLines
* fsi: sbefifo: Use interruptible mutex lockingEddie James2021-10-221-3/+9
| | | | | | | | | | | | | Some SBE operations have extremely large responses and can require several minutes to process the response. During this time, the device lock must be held. If another process attempts an operation, it will wait for the mutex for longer than the kernel hung task watchdog allows. Therefore, use the interruptible function to lock the mutex. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210803213016.44739-1-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: sbefifo: Add sysfs file indicating a timeout errorEddie James2021-10-221-0/+16
| | | | | | | | | | | | | The SBEFIFO timeout error requires special handling in userspace to do recovery operations. Add a sysfs file to indicate a timeout error, and notify pollers when a timeout occurs. This will be used by the openpower-occ-control application. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20211019211749.38059-3-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: occ: Store the SBEFIFO FFDC in the user response bufferEddie James2021-10-221-18/+48
| | | | | | | | | | | | | If the SBEFIFO response indicates an error, store the response in the user buffer and return an error. Previously, the user had no way of obtaining the SBEFIFO FFDC. The user's buffer now contains data in the event of a failure. No change in the event of a successful transfer. Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20211019205307.36946-3-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: occ: Use a large buffer for responsesEddie James2021-10-221-66/+44
| | | | | | | | | | | | | | | | | | | | Allocate a large buffer for each OCC to handle response data. This removes memory allocation during an operation, and also allows for the maximum amount of SBE FFDC. Previously for the putsram and attn commands, only 32 words would have been available, and for getsram, only up to the size of the transfer. SBE FFDC might be up to 8Kb. The SBE interface expects data to be specified in units of words (4 bytes), defined as OCC_MAX_RESP_WORDS. This change allows the full FFDC capture to be implemented, where before it was not available. Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20211019205307.36946-2-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: occ: Force sequence numbering per OCCEddie James2021-10-151-17/+37
| | | | | | | | | | | | | | Set and increment the sequence number during the submit operation. This prevents sequence number conflicts between different users of the interface. A sequence number conflict may result in a user getting an OCC response meant for a different command. Since the sequence number is now modified, the checksum must be calculated and set before submitting the command. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210721190231.117185-2-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi/sbefifo: Fix reset timeoutJoachim Fenkes2021-06-041-3/+5
| | | | | | | | | | | | | On BMCs with lower timer resolution than 1ms, msleep(1) will take way longer than 1ms, so looping 10k times won't wait for 10s but significantly longer. Fix this by using jiffies like the rest of the code. Fixes: 9f4a8a2d7f9d ("fsi/sbefifo: Add driver for the SBE FIFO") Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Link: https://lore.kernel.org/r/20200724071518.430515-3-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi/sbefifo: Clean up correct FIFO when receiving reset request from SBEJoachim Fenkes2021-06-041-1/+1
| | | | | | | | | | | When the SBE requests a reset via the down FIFO, that is also the FIFO we should go and reset ;) Fixes: 9f4a8a2d7f9d ("fsi/sbefifo: Add driver for the SBE FIFO") Signed-off-by: Joachim Fenkes <FENKES@de.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20200724071518.430515-2-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: master-ast-cf: Remove redundant error printing in fsi_master_acf_probe()Zhen Lei2021-06-041-1/+0
| | | | | | | | | | | | | | | When devm_ioremap_resource() fails, a clear enough error message will be printed by its subfunction __devm_ioremap_resource(). The error information contains the device name, failure cause, and possibly resource information. Therefore, remove the error printing here to simplify code and reduce the binary size. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Link: https://patchwork.ozlabs.org/project/linux-fsi/patch/20210511085745.4340-1-thunder.leizhen@huawei.com/ Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: Aspeed: Reduce poll timeoutEddie James2021-06-041-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The lengthy timeout previously used sometimes resulted in scheduling problems, detailed below. Therefore reduce the timeout to 500us. This timeout selection is supported by the benchmarks collected below with various clock dividers. This is purely the time spent polling (reported by ktime_get()). div 1: max:150us avg: 2us div 2: max:155us avg: 3us div 4: max:149us avg: 7us div 8: max:153us avg: 13us div 16: max:197us avg: 21us div 32: max:181us avg: 50us div 64: max:262us avg:100us Jan 22 01:27:21 rain27bmc kernel: rcu: INFO: rcu_sched self-detected stall on CPU Jan 22 01:27:21 rain27bmc kernel: rcu: 0-....: (2099 ticks this GP) idle=0ca/1/0x40000002 softirq=349573/349573 fqs=1048 Jan 22 01:27:21 rain27bmc kernel: (t=2100 jiffies g=841149 q=7163) Jan 22 01:27:21 rain27bmc kernel: NMI backtrace for cpu 0 Jan 22 01:27:21 rain27bmc kernel: CPU: 0 PID: 5959 Comm: ibm-read-vpd Not tainted 5.8.17-a9b4ea8 #1 Jan 22 01:27:21 rain27bmc kernel: Hardware name: Generic DT based system Jan 22 01:27:21 rain27bmc kernel: Backtrace: Jan 22 01:27:25 rain27bmc kernel: [<8010d92c>] (dump_backtrace) from [<8010db80>] (show_stack+0x20/0x24) ... Jan 22 01:27:25 rain27bmc kernel: [<8010130c>] (gic_handle_irq) from [<80100b0c>] (__irq_svc+0x6c/0x90) Jan 22 01:27:25 rain27bmc kernel: Exception stack(0xb79159b0 to 0xb79159f8) Jan 22 01:27:25 rain27bmc kernel: 59a0: 9e88e5d5 00000559 00000559 00000018 Jan 22 01:27:25 rain27bmc kernel: 59c0: 00000000 9f217c55 00000003 00000559 a0201c00 bfa4d048 bfa4d000 b7915a44 Jan 22 01:27:25 rain27bmc kernel: 59e0: 40e88f8a b7915a00 3254e553 80734924 80030113 ffffffff Jan 22 01:27:25 rain27bmc kernel: r9:b7914000 r8:a0201c00 r7:b79159e4 r6:ffffffff r5:80030113 r4:80734924 Jan 22 01:27:25 rain27bmc kernel: [<807348b4>] (__opb_read) from [<80734d98>] (aspeed_master_read+0xbc/0xcc) Jan 22 01:27:25 rain27bmc kernel: r10:00000004 r9:00000002 r8:80734cdc r7:bd33fa40 r6:00000004 r5:bd33f840 Jan 22 01:27:25 rain27bmc kernel: r4:00201c00 Jan 22 01:27:25 rain27bmc kernel: [<80734cdc>] (aspeed_master_read) from [<807320f0>] (fsi_master_read+0x6c/0x1bc) ... Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20210211194846.35475-1-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: aspeed: convert to devm_platform_ioremap_resourceYangtao Li2021-06-041-3/+1
| | | | | | | | | Use devm_platform_ioremap_resource() to simplify code. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20191228190631.26777-1-tiny.windzz@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: occ: Log error for checksum failureEddie James2021-06-041-3/+7
| | | | | | | | | | Log an error if the response checksum doesn't match the calculated checksum. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210209171235.20624-3-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: occ: Don't accept response from un-initialized OCCEddie James2021-06-041-0/+1
| | | | | | | | | | | | If the OCC is not initialized and responds as such, the driver should continue waiting for a valid response until the timeout expires. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Fixes: 7ed98dddb764 ("fsi: Add On-Chip Controller (OCC) driver") Link: https://lore.kernel.org/r/20210209171235.20624-2-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: scom: Remove retriesJoel Stanley2021-06-041-60/+29
| | | | | | | | | | | | | | | | On a functioning FSI link there is not need to retry a write when doing a scom in the driver. Allow the higher layers (eg. userspace) to attempt a retry if they want, or to accept that the address they are talking to is not accessible. By removing the retries we can separate the error handling from retry logic. In particular -EBUSY was used to force the get/put scom logic to retry. Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210527070109.225198-1-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: scom: Reset the FSI2PIB engine for any errorEddie James2021-06-041-7/+9
| | | | | | | | | | | | The error bits in the FSI2PIB status are only cleared by a reset. So the driver needs to perform a reset after seeing any of the FSI2PIB errors, otherwise subsequent operations will also look like failures. Fixes: 6b293258cded ("fsi: scom: Major overhaul") Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210329151344.14246-1-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: aspeed: Emit fewer barriers in opb operationsJoel Stanley2021-06-041-9/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When setting up a read or write to the OPB memory space, we must perform five or six AHB writes. The ordering of these up until the trigger write does not matter, so use writel_relaxed. The generated code goes from (Debian GCC 10.2.1-6): mov r8, r3 mcr 15, 0, sl, cr7, cr10, {4} str sl, [r6, #20] mcr 15, 0, sl, cr7, cr10, {4} str r3, [r6, #24] mcr 15, 0, sl, cr7, cr10, {4} str r1, [r6, #28] mcr 15, 0, sl, cr7, cr10, {4} str r2, [r6, #32] mcr 15, 0, sl, cr7, cr10, {4} mov r1, #1 str r1, [r6, #64] ; 0x40 mcr 15, 0, sl, cr7, cr10, {4} str r1, [r6, #4] to this: str r3, [r7, #20] str r2, [r7, #24] str r1, [r7, #28] str r3, [r7, #64] mov r8, #0 mcr 15, 0, r8, cr7, cr10, {4} str r3, [r7, #4] Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Jeremy Kerr <jk@ozlabs.org> Reviewed-by: Eddie James <eajames@linux.ibm.com> Tested-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20210223041737.171274-1-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: core: Fix return of error values on failuresColin Ian King2021-06-041-2/+2
| | | | | | | | | | | | | | Currently the cfam_read and cfam_write functions return the provided number of bytes given in the count parameter and not the error return code in variable rc, hence all failures of read/writes are being silently ignored. Fix this by returning the error code in rc. Addresses-Coverity: ("Unused value") Fixes: d1dcd6782576 ("fsi: Add cfam char devices") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Jeremy Kerr <jk@ozlabs.org> Link: https://lore.kernel.org/r/20210603122812.83587-1-colin.king@canonical.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: Add missing MODULE_DEVICE_TABLEZou Wei2021-06-044-0/+4
| | | | | | | | | | | This patch adds missing MODULE_DEVICE_TABLE definition which generates correct modalias for automatic loading of this driver when it is built as an external module. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zou Wei <zou_wei@huawei.com> Link: https://lore.kernel.org/r/1620896249-52769-1-git-send-email-zou_wei@huawei.com Signed-off-by: Joel Stanley <joel@jms.id.au>
* Merge tag 'hwmon-for-v5.11' of ↵Linus Torvalds2020-12-161-34/+91
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon updates from Guenter Roeck: "New drivers: - SB-TSI sensors - Lineat Technology LTC2992 - Delta power supplies Q54SJ108A2 - Maxim MAX127 - Corsair PSU - STMicroelectronics PM6764 Voltage Regulator New chip support: - P10 added to fsi/occ driver - NCT6687D added to nct6883 driver - Intel-based Xserves added to applesmc driver - AMD family 19h model 01h added to amd_energy driver And various minor bug fixes and improvements" * tag 'hwmon-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (41 commits) dt-bindings: (hwmon/sbtsi_temp) Add SB-TSI hwmon driver bindings hwmon: (sbtsi) Add documentation hwmon: (sbtsi) Add basic support for SB-TSI sensors hwmon: (iio_hwmon) Drop bogus __refdata annotation hwmon: (xgene) Drop bogus __refdata annotation dt-bindings: hwmon: convert AD ADM1275 bindings to dt-schema hwmon: (occ) Add new temperature sensor type fsi: occ: Add support for P10 dt-bindings: fsi: Add P10 OCC device documentation dt-bindings: hwmon: convert TI ADS7828 bindings to dt-schema dt-bindings: hwmon: convert AD AD741x bindings to dt-schema dt-bindings: hwmon: convert TI INA2xx bindings to dt-schema hwmon: (ltc2992) Fix less than zero comparisons with an unsigned integer hwmon: (pmbus/q54sj108a2) Correct title underline length dt-bindings: hwmon: Add documentation for ltc2992 hwmon: (ltc2992) Add support for GPIOs. hwmon: (ltc2992) Add support hwmon: (pmbus) Driver for Delta power supplies Q54SJ108A2 hwmon: Add driver for STMicroelectronics PM6764 Voltage Regulator hwmon: (nct6683) Support NCT6687D. ...
| * fsi: occ: Add support for P10Eddie James2020-12-111-34/+91
| | | | | | | | | | | | | | | | | | | | | | | | The P10 OCC has a different SRAM address for the command and response buffers. In addition, the SBE commands to access the SRAM have changed format. Add versioning to the driver to handle these differences. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20201120010315.190737-3-joel@jms.id.au Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* | fsi: Aspeed: Add mutex to protect HW accessEddie James2020-12-091-16/+29
|/ | | | | | | | | | | | | There is nothing to prevent multiple commands being executed simultaneously. Add a mutex to prevent this. Fixes: 606397d67f41 ("fsi: Add ast2600 master driver") Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20201120004929.185239-1-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: aspeed: Support CFAM reset GPIOJoel Stanley2020-09-101-0/+43
| | | | | | | | | | | | | | | | | | | | Systems have a line for restting the remote CFAM. This is not part of the FSI master, but is associated with it, so it makes sense to include it in the master driver. This exposes a sysfs interface to reset the cfam, abstracting away the direction and polarity of the GPIO, as well as the timing of the reset pulse. Userspace will be blocked until the reset pulse is finished. The reset is hard coded to be in the range of (900, 1000) us. It was observed with a scope to regularly be just over 1ms. If the device tree property is not preset the driver will silently continue. Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20200728025527.174503-6-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: aspeed: Add module param for bus divisorJoel Stanley2020-09-101-2/+6
| | | | | | | | | | | | | For testing and hardware debugging a user may wish to override the divisor at runtime. By setting fsi_master_aspeed.bus_div=N, the divisor will be set to N, if 0 < N <= 0x3ff. This is a module parameter and not a device tree option as it will only need to be set when testing or debugging. Reviewed-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20200728025527.174503-5-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: aspeed: Run the bus at maximum speedJoel Stanley2020-09-101-3/+14
| | | | | | | | | | | | Testing of Tacoma has shown that the ASPEED master can be run at maximum speed. The exception is when wired externally with a cable, in which case we use a divisor of two to ensure reliable operation. Reviewed-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20200728025527.174503-4-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: aspeed: Support cabled FSIJoel Stanley2020-09-101-0/+46
| | | | | | | | | | | | | | | | | | Some FSI capable systems have internal FSI signals, and some have external cabled FSI. Software can detect which machine this is by reading a jumper GPIO, and also control which pins the signals are routed to through a mux GPIO. This attempts to find the GPIOs at probe time. If they are not present in the device tree the driver will not error and continue as before. The mux GPIO is owned by the FSI driver to ensure it is not modified at runtime. The routing jumper obtained as non-exclusive to allow other software to inspect it's state. Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20200728025527.174503-3-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: scom: Constify scom_idsRikard Falkeborn2020-09-101-1/+1
| | | | | | | | | The only usage of scom_ids is to assign its address to the id_table field in the fsi_driver struct, which is a const pointer, so make it const to allow the compiler to put it in read-only memory Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: sbefifo: Constify sbefifo_idsRikard Falkeborn2020-09-101-1/+1
| | | | | | | | | The only usage of sbefifo_ids is to assign its address to the id_table field in the fsi_driver struct, which is a const pointer, so make it const to allow the compiler to put it in read-only memory Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: master: Constify hub_master_idsRikard Falkeborn2020-09-101-1/+1
| | | | | | | | | The only usage of hub_master_ids is to assign its address to the id_table field in the fsi_driver struct, which is a const pointer, so make it const to allow the compiler to put it in read-only memory. Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: master: Remove link enable read-backEddie James2020-09-102-13/+4
| | | | | | | | Both the Aspeed and hub masters read back the link enable register after enabling the link, but this is unnecessary, so remove it. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: core: Set slave local bus ownership during initEddie James2020-09-101-1/+15
| | | | | | | | | | | | | | | | | | The driver ought to claim local bus ownership of the slave it's communicating with. This is for multi-master setups. The slave (in theory) will deny access to masters who try to access the CFAM address space but who don't "own" the bus. As driver doesn't seem to perform any other teardown there is no need to "un-claim" ownership at teardown. Also I'm not aware of any multi-master setup using this driver so it shouldn't actually matter. Also, the hardware doesn't seem to enforce this despite being required in the specification... Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: core: Disable link when slave init failsEddie James2020-09-101-1/+12
| | | | | | | | | In the case that links don't have slaves or fail to be accessed, the master should disable the link during the scan since it won't be using the slave. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: master: Add boolean parameter to link_enable functionEddie James2020-09-106-8/+21
| | | | | | | | | | Add the ability to disable a link with a boolean parameter to the link_enable function. This is necessary so that the master can disable links that it isn't using; for example, links to slaves that fail initialization. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: fsi-occ: fix return value check in occ_probe()Xu Wang2020-09-101-1/+1
| | | | | | | | | | In case of error, the function platform_device_register_full() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by: Xu Wang <vulab@iscas.ac.cn> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: aspeed: Enable 23-bit addressingEddie James2020-09-101-2/+4
| | | | | | | | | | In order to access more than the second hub link, 23-bit addressing is required. The core provides the highest two bits of address as the slave ID to the master. Signed-off-by: Eddie James <eajames@linux.ibm.com> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Joel Stanley <joel@jms.id.au>
* fsi: master-ast-cf: fix spelling mistake "firwmare" -> "firmware"Colin Ian King2020-09-101-1/+1
| | | | | | | | There is a spelling mistake in a dev_err error message. Fix it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au>
* treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada2020-06-131-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
* fsi: aspeed: add unspecified HAS_IOMEM dependencyBrendan Higgins2020-02-101-0/+1
| | | | | | | | | | | | | | | | | | | | Currently CONFIG_FSI_MASTER_ASPEED=y implicitly depends on CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get the following build error: ld: drivers/fsi/fsi-master-aspeed.o: in function `fsi_master_aspeed_probe': drivers/fsi/fsi-master-aspeed.c:436: undefined reference to `devm_ioremap_resource' Fix the build error by adding the unspecified dependency. Fixes: 606397d67f41 ("fsi: Add ast2600 master driver") Cc: stable@vger.kernel.org Reported-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Brendan Higgins <brendanhiggins@google.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20200131034832.294268-1-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: aspeed: Fix OPB0 byte order register valuesAndrew Jeffery2019-11-081-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The data byte order selection registers in the APB2OPB primarily expose some internal plumbing necessary to get correct write accesses onto the OPB. OPB write cycles require "data mirroring" across the 32-bit data bus to support variable data width slaves that don't implement "byte enables". For slaves that do implement byte enables the master can signal which bytes on the data bus the slave should consider valid. The data mirroring behaviour is specified by the following table: +-----------------+----------+-----------------------------------+ | | | 32-bit Data Bus | +---------+-------+----------+---------+---------+-------+-------+ | | | | | | | | | ABus | Mn_BE | Request | Dbus | Dbus | Dbus | Dbus | | (30:31) | (0:3) | Transfer | 0:7 | 8:15 | 16:23 | 24:31 | | | | Size | byte0 | byte1 | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1111 | fullword | byte0 | byte1 | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1110 | halfword | byte0 | byte1 | byte2 | | +---------+-------+----------+---------+---------+-------+-------+ | 01 | 0111 | byte | _byte1_ | byte1 | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1100 | halfword | byte0 | byte1 | | | +---------+-------+----------+---------+---------+-------+-------+ | 01 | 0110 | byte | _byte1_ | byte1 | byte2 | | +---------+-------+----------+---------+---------+-------+-------+ | 10 | 0011 | halfword | _byte2_ | _byte3_ | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1000 | byte | byte0 | | | | +---------+-------+----------+---------+---------+-------+-------+ | 01 | 0100 | byte | _byte1_ | byte1 | | | +---------+-------+----------+---------+---------+-------+-------+ | 10 | 0010 | byte | _byte2_ | | byte2 | | +---------+-------+----------+---------+---------+-------+-------+ | 11 | 0001 | byte | _byte3_ | _byte3_ | | byte3 | +---------+-------+----------+---------+---------+-------+-------+ Mirrored data values are highlighted by underscores in the Dbus columns. The values in the ABus and Request Transfer Size columns correspond to values in the field names listed in the write data order select register descriptions. Similar configuration registers are exposed for reads which enables the secondary purpose of configuring hardware endian conversions. It appears the data bus byte order is switched around in hardware so set the registers such that we can access the correct values for all widths. The values were determined by experimentation on hardware against fixed CFAM register values to configure the read data order, then in combination with the table above and the register layout documentation in the AST2600 datasheet performing write/read cycles to configure the write data order registers. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Alistair Popple <alistair@popple.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-12-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: aspeed: Add trace pointsJoel Stanley2019-11-081-0/+22
| | | | | | | | | These trace points help with debugging the FSI master. They show the low level reads, writes and error states of the master. Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-11-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: Add ast2600 master driverJoel Stanley2019-11-083-0/+531
| | | | | | | | | | | | | | | | | | | The ast2600 BMC has a pair of FSI masters in it, behind an AHB to OPB bridge. The master driver supports reads and writes of full words, half word and byte accesses to remote CFAMs. It can perform very basic error recovery through resetting of the FSI port when an error is detected, and the issuing of breaks and terms. Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Alistair Popple <alistair@popple.id.au> -- v2: - remove debugging - squash in fixes Link: https://lore.kernel.org/r/20191108051945.7109-10-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: Move defines to common headerJoel Stanley2019-11-082-46/+71
| | | | | | | | | | | | | | The FSI master registers are common to the hub and AST2600 master (and the FSP2, if someone was to upstream a driver for that). Add defines to the fsi-master.h header, and introduce headings to delineate the existing low level details. Acked-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-8-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: fsi_master_class can be statickbuild test robot2019-11-081-1/+1
| | | | | | | | | | There are no users outside of this file. Fixes: 0604d53d4da8 ("fsi: Add fsi-master class") Signed-off-by: kbuild test robot <lkp@intel.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-7-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: core: Fix small accesses and unaligned offsets via sysfsAndrew Jeffery2019-11-081-4/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Subtracting the offset delta from four-byte alignment lead to wrapping of the requested length where `count` is less than `off`. Generalise the length handling to enable and optimise aligned access sizes for all offset and size combinations. The new formula produces the following results for given offset and count values: offset count | length --------------+------- 0 1 | 1 0 2 | 2 0 3 | 2 0 4 | 4 0 5 | 4 1 1 | 1 1 2 | 1 1 3 | 1 1 4 | 1 1 5 | 1 2 1 | 1 2 2 | 2 2 3 | 2 2 4 | 2 2 5 | 2 3 1 | 1 3 2 | 1 3 3 | 1 3 4 | 1 3 5 | 1 We might need something like this for the cfam chardevs as well, for example we don't currently implement any alignment restrictions / handling in the hardware master driver. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-6-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: Move master attributes to fsi-master classJeremy Kerr2019-11-081-14/+9
| | | | | | | | | | | Populate fsi_master_class->dev_attrs with the existing attribute definitions, so we don't need to explicitly register. Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Alistair Popple <alistair@popple.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-3-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: Add fsi-master classJeremy Kerr2019-11-081-0/+13
| | | | | | | | | | | This change adds a device class for FSI masters, allowing access under /sys/class/fsi-master/, and easier udev rules. Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Alistair Popple <alistair@popple.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-2-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: scom: Don't abort operations for minor errorsEddie James2019-08-281-7/+1
| | | | | | | | | | | | | | | | | | The scom driver currently fails out of operations if certain system errors are flagged in the status register; system checkstop, special attention, or recoverable error. These errors won't impact the ability of the scom engine to perform operations, so the driver should continue under these conditions. Also, don't do a PIB reset for these conditions, since it won't help. Fixes: 6b293258cded ("fsi: scom: Major overhaul") Signed-off-by: Eddie James <eajames@linux.ibm.com> Cc: stable <stable@vger.kernel.org> Acked-by: Jeremy Kerr <jk@ozlabs.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20190827041249.13381-1-jk@ozlabs.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fsi: sbefifo: Don't fail operations when in SBE IPL stateEddie James2019-07-031-2/+2
| | | | | | | | | | | | SBE fifo operations should be allowed while the SBE is in any of the "IPL" states. Operations should succeed in this state. Fixes: 9f4a8a2d7f9d fsi/sbefifo: Add driver for the SBE FIFO Reviewed-by: Joel Stanley <joel@jms.id.au> Tested-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/1561575415-3282-1-git-send-email-eajames@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'fsi-for-5.3' of ↵Greg Kroah-Hartman2019-07-032-15/+32
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi into char-misc-next Joel writes: FSI changes for 5.3 - Add MAINTAINERS entry. There is now a git tree and a mailing list/patchwork for collecting FSI patches - Bug fix for error driver registration error paths - Correction for the OCC hwmon driver to meet the spec * tag 'fsi-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi: fsi/core: Fix error paths on CFAM init OCC: FSI and hwmon: Add sequence numbering MAINTAINERS: Add FSI subsystem
| * fsi/core: Fix error paths on CFAM initJeremy Kerr2019-07-031-12/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change d1dcd67825 re-worked the struct fsi_slave initialisation in fsi_slave_init, but introduced a few inconsitencies: the slave->dev is now registered through cdev_device_add, but we may kfree() the device out from underneath the cdev registration. We may also leave an IDA allocated. This change fixes the error paths, so that we kfree() only before the device is registered with the core code. We also move the smode write to before we start creating proper devices, as it's the most likely to fail. We also remove the IDA-allocated minor on error, and properly clean up the of_node. Fixes: d1dcd6782576 ("fsi: Add cfam char devices") Reported-by: Lei YU <mine260309@gmail.com> Tested-by: John Wang <wangzqbj@inspur.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Joel Stanley <joel@jms.id.au>
| * OCC: FSI and hwmon: Add sequence numberingEddie James2019-07-031-3/+12
| | | | | | | | | | | | | | | | | | | | | | Sequence numbering of the commands submitted to the OCC is required by the OCC interface specification. Add sequence numbering and check for the correct sequence number on the response. Signed-off-by: Eddie James <eajames@linux.ibm.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Lei YU <mine260309@gmail.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
* | Merge 5.2-rc6 into char-misc-nextGreg Kroah-Hartman2019-06-231-9/+1
|\ \ | | | | | | | | | | | | | | | We need the char-misc fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-12 13:25:52 +0100