| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
| |
Return proper error in brcmstb_gpio_probe if bank width is invalid.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
| |
Use list_for_each_entry to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Broadcom MIPS-based STB chips endianness is configured by boot strap,
which also reverses all bus endianness (i.e., big-endian CPU + big
endian bus ==> native endian I/O).
Other architectures (e.g., ARM) either do not support big endian, or
else leave I/O in little endian mode.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The separate struct bgpio_chip has been a pain to handle, both
by being confusingly similar in name to struct gpio_chip and
for being contained inside a struct so that struct gpio_chip
is contained in a struct contained in a struct, making several
steps of dereferencing necessary.
Make things simpler: include the fields directly into
<linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and
get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix
some of the member variables with bgpio_* and add proper
kerneldoc while we're at it.
Modify all users to handle the change and use a struct
gpio_chip directly. And while we're at it: replace all
container_of() dereferencing by gpiochip_get_data() and
registering the gpio_chip with gpiochip_add_data().
Cc: arm@kernel.org
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|\
| |
| |
| | |
Linux 4.2-rc4
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If a failure occurs during probe, brcmstb_gpio_remove() is called. In
remove, we call platform_get_drvdata(), but at the time of failure in
the probe the driver data hadn't yet been set which leads to a NULL
ptr dereference in the remove's list_for_each. Call
platform_set_drvdata() and set up list head right after allocating the
priv struct to both avoid the null pointer dereference that could
occur today. To guard against potential future changes, check for
null pointer in remove.
Reported-by: Tim Ross <tross@broadcom.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For wake from S5, we need to:
- register a reboot handler
- set wakeup capability before requesting IRQ so wakeup count is
incremented
- mask all GPIO IRQs and clear any pending interrupts during driver
probe to since no driver will yet be registered to handle any IRQs
carried over from boot at that time, and it's possible that the
booted kernel does not request the same IRQ anyway.
This means that /sys/.../power/wakeup_count is valid at boot time, and
we can properly account for S5 wakeup stats. e.g.:
### After waking from S5 from a GPIO key
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup
enabled
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup_count
1
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Uses the gpiolib irqchip helpers. For this to work, the irq setup
function is called once per bank instead of once per device. Note
that all known uses of this block have a BCM7120 L2 interrupt
controller as a parent. Supports interrupts for all GPIOs.
In the IRQ handler, we check for raised IRQs for invalid GPIOs and
warn (ratelimited) if they're encountered.
Also, several drivers (e.g. gpio-keys) allow for GPIOs to be
configured as wakeup sources, and this GPIO controller supports that
through a separate interrupt path.
The de-facto standard DT property "wakeup-source" is checked, since
that indicates whether the GPIO controller hardware can wake. Uses
the IRQCHIP_MASK_ON_SUSPEND irq_chip flag because UPG GIO doesn't have
any of its own wakeup source configuration.
Aside regarding gpiolib irqchip helpers: It wasn't obvious (to me)
that you can have multiple chained irqchips and associated IRQ domains
for a single parent IRQ, and as long as the xlate function is written
correctly, a GPIO IRQ request end up checking the correct domain and
will get associated with the correct IRQ. What helps make this clear
is to read
drivers/gpio/gpiolib-of.c:
- of_gpiochip_find_and_xlate()
- of_get_named_gpiod_flags()
drivers/gpio/gpiolib.c:
- gpiochip_find()
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds support for the GPIO IP "UPG GIO" used on
Broadcom STB SoCs (BCM7XXX and some others). Uses
basic_mmio_gpio to instantiate a gpio_chip for each bank.
The driver assumes that it handles the base set of GPIOs
on the system and that it can start its numbering sequence
from 0, so any GPIO expanders used with it must dynamically
assign GPIO numbers after this driver has finished
registering its GPIOs.
Does not implement the interrupt-controller portion yet,
will be done in a future commit.
v2:
- change include to use <linux/gpio/driver.h> instead of
<linux/gpio.h>
- get rid of unnecessary imask member in struct bank
- rename GPIO_PER_BANK -> MAX_GPIO_PER_BANK
- always have 32 GPIOs per bank and add 'width' member in
struct bank to hold actual number of GPIOs in use
- mark of_match table as const
List-usage-fixed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|