summaryrefslogtreecommitdiffstats
path: root/drivers/hv (follow)
Commit message (Collapse)AuthorAgeFilesLines
* Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashionK. Y. Srinivasan2015-06-131-2/+12
| | | | | | | | | Allocate ring buffer memory from the NUMA node assigned to the channel. Since this is a performance and not a correctness issue, if the node specific allocation were to fail, fall back and allocate without specifying the node. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Implement NUMA aware CPU affinity for channelsK. Y. Srinivasan2015-06-011-29/+43
| | | | | | | | | | | | Channels/sub-channels can be affinitized to VCPUs in the guest. Implement this affinity in a way that is NUMA aware. The current protocol distributed the primary channels uniformly across all available CPUs. The new protocol is NUMA aware: primary channels are distributed across the available NUMA nodes while the sub-channels within a primary channel are distributed amongst CPUs within the NUMA node assigned to the primary channel. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Use the vp_index map even for channels bound to CPU 0K. Y. Srinivasan2015-06-011-1/+1
| | | | | | | | | | | Map target_cpu to target_vcpu using the mapping table. We should use the mapping table to transform guest CPU ID to VP Index as is done for the non-performance critical channels. While the value CPU 0 is special and will map to VP index 0, it is good to be consistent. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: balloon: check if ha_region_mutex was acquired in ↵Vitaly Kuznetsov2015-05-311-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MEM_CANCEL_ONLINE case Memory notifiers are being executed in a sequential order and when one of them fails returning something different from NOTIFY_OK the remainder of the notification chain is not being executed. When a memory block is being onlined in online_pages() we do memory_notify(MEM_GOING_ONLINE, ) and if one of the notifiers in the chain fails we end up doing memory_notify(MEM_CANCEL_ONLINE, ) so it is possible for a notifier to see MEM_CANCEL_ONLINE without seeing the corresponding MEM_GOING_ONLINE event. E.g. when CONFIG_KASAN is enabled the kasan_mem_notifier() is being used to prevent memory hotplug, it returns NOTIFY_BAD for all MEM_GOING_ONLINE events. As kasan_mem_notifier() comes before the hv_memory_notifier() in the notification chain we don't see the MEM_GOING_ONLINE event and we do not take the ha_region_mutex. We, however, see the MEM_CANCEL_ONLINE event and unconditionally try to release the lock, the following is observed: [ 110.850927] ===================================== [ 110.850927] [ BUG: bad unlock balance detected! ] [ 110.850927] 4.1.0-rc3_bugxxxxxxx_test_xxxx #595 Not tainted [ 110.850927] ------------------------------------- [ 110.850927] systemd-udevd/920 is trying to release lock (&dm_device.ha_region_mutex) at: [ 110.850927] [<ffffffff81acda0e>] mutex_unlock+0xe/0x10 [ 110.850927] but there are no more locks to release! At the same time we can have the ha_region_mutex taken when we get the MEM_CANCEL_ONLINE event in case one of the memory notifiers after the hv_memory_notifier() in the notification chain failed so we need to add the mutex_is_locked() check. In case of MEM_ONLINE we are always supposed to have the mutex locked. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus:Update preferred vmbus protocol version to windows 10.Keith Mange2015-05-311-3/+5
| | | | | | | | Add support for Windows 10. Signed-off-by: Keith Mange <keith.mange@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: distribute subchannels among all vcpusVitaly Kuznetsov2015-05-241-1/+28
| | | | | | | | | | | Primary channels are distributed evenly across all vcpus we have. When the host asks us to create subchannels it usually makes us num_cpus-1 offers and we are supposed to distribute the work evenly among the channel itself and all its subchannels. Make sure they are all assigned to different vcpus. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: move init_vp_index() call to vmbus_process_offer()Vitaly Kuznetsov2015-05-241-2/+5
| | | | | | | | | | | | We need to call init_vp_index() after we added the channel to the appropriate list (global or subchannel) to be able to use this information when assigning the channel to the particular vcpu. To do so we need to move a couple of functions around. The only real change is the init_vp_index() call. This is a small refactoring without a functional change. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: decrease num_sc on subchannel removalVitaly Kuznetsov2015-05-241-1/+2
| | | | | | | | | | It is unlikely that that host will ask us to close only one subchannel for a device but let's be consistent. Do both num_sc++ and num_sc-- with channel->lock to be on the safe side. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: unify calls to percpu_channel_enq()Vitaly Kuznetsov2015-05-241-33/+18
| | | | | | | | Remove some code duplication, no functional change intended. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: kill tasklets on module unloadVitaly Kuznetsov2015-05-241-1/+4
| | | | | | | | Explicitly kill tasklets we create on module unload. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: do cleanup on all vmbus_open() failure pathsVitaly Kuznetsov2015-05-241-7/+6
| | | | | | | | | | | | | In case there was an error reported in the response to the CHANNELMSG_OPENCHANNEL call we need to do the cleanup as a vmbus_open() user won't be doing it after receiving an error. The cleanup should be done on all failure paths. We also need to avoid returning open_info->response.open_result.status as the return value as all other errors we return from vmbus_open() are -EXXX and vmbus_open() callers are not supposed to analyze host error codes. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Implement the protocol for tearing down vmbus stateK. Y. Srinivasan2015-05-244-1/+33
| | | | | | | | | Implement the protocol for tearing down the monitor state established with the host. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hv: vmbus_free_channels(): remove the redundant free_channel()Dexuan Cui2015-05-241-3/+8
| | | | | | | | | | | | | | | | | | | | free_channel() has been invoked in vmbus_remove() -> hv_process_channel_removal(), or vmbus_remove() -> ... -> vmbus_close_internal() -> hv_process_channel_removal(). We also change to use list_for_each_entry_safe(), because the entry is removed in hv_process_channel_removal(). This patch fixes a bug in the vmbus unload path. Thank Dan Carpenter for finding the issue! Signed-off-by: Dexuan Cui <decui@microsoft.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: unregister panic notifier on module unloadVitaly Kuznetsov2015-05-241-0/+4
| | | | | | | | | | | | | | | | | | | | | | | Commit 96c1d0581d00f7abe033350edb021a9d947d8d81 ("Drivers: hv: vmbus: Add support for VMBus panic notifier handler") introduced atomic_notifier_chain_register() call on module load. We also need to call atomic_notifier_chain_unregister() on module unload as otherwise the following crash is observed when we bring hv_vmbus back: [ 39.788877] BUG: unable to handle kernel paging request at ffffffffa00078a8 [ 39.788877] IP: [<ffffffff8109d63f>] notifier_call_chain+0x3f/0x80 ... [ 39.788877] Call Trace: [ 39.788877] [<ffffffff8109de7d>] __atomic_notifier_call_chain+0x5d/0x90 ... [ 39.788877] [<ffffffff8109d788>] ? atomic_notifier_chain_register+0x38/0x70 [ 39.788877] [<ffffffff8109d767>] ? atomic_notifier_chain_register+0x17/0x70 [ 39.788877] [<ffffffffa002814f>] hv_acpi_init+0x14f/0x1000 [hv_vmbus] [ 39.788877] [<ffffffff81002144>] do_one_initcall+0xd4/0x210 Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: introduce vmbus_acpi_removeVitaly Kuznetsov2015-05-241-0/+10
| | | | | | | | | | | | | | | | | | | | | In case we do request_resource() in vmbus_acpi_add() we need to tear it down to be able to load the driver again. Otherwise the following crash in observed when hv_vmbus unload/load sequence is performed on a Generation2 instance: [ 38.165701] BUG: unable to handle kernel paging request at ffffffffa00075a0 [ 38.166315] IP: [<ffffffff8107dc5f>] __request_resource+0x2f/0x50 [ 38.166315] PGD 1f34067 PUD 1f35063 PMD 3f723067 PTE 0 [ 38.166315] Oops: 0000 [#1] SMP [ 38.166315] Modules linked in: hv_vmbus(+) [last unloaded: hv_vmbus] [ 38.166315] CPU: 0 PID: 267 Comm: modprobe Not tainted 3.19.0-rc5_bug923184+ #486 [ 38.166315] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012 [ 38.166315] task: ffff88003f401cb0 ti: ffff88003f60c000 task.ti: ffff88003f60c000 [ 38.166315] RIP: 0010:[<ffffffff8107dc5f>] [<ffffffff8107dc5f>] __request_resource+0x2f/0x50 [ 38.166315] RSP: 0018:ffff88003f60fb58 EFLAGS: 00010286 Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: utils: unify driver registration reportingVitaly Kuznetsov2015-05-243-4/+4
| | | | | | | | | | Unify driver registration reporting and move it to debug level as normally daemons write to syslog themselves and these kernel messages are useless. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: fcopy: full handshake supportVitaly Kuznetsov2015-05-241-1/+15
| | | | | | | | | | Introduce FCOPY_VERSION_1 to support kernel replying to the negotiation message with its own version. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vss: full handshake supportVitaly Kuznetsov2015-05-241-12/+37
| | | | | | | | | | Introduce VSS_OP_REGISTER1 to support kernel replying to the negotiation message with its own version. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: kvp: convert to hv_utils_transportVitaly Kuznetsov2015-05-241-49/+42
| | | | | | | | | Convert to hv_utils_transport to support both netlink and /dev/vmbus/hv_kvp communication methods. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: fcopy: convert to hv_utils_transportVitaly Kuznetsov2015-05-241-148/+46
| | | | | | | | | | Unify the code with the recently introduced hv_utils_transport. Netlink communication is disabled for fcopy. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vss: convert to hv_utils_transportVitaly Kuznetsov2015-05-241-25/+27
| | | | | | | | | Convert to hv_utils_transport to support both netlink and /dev/vmbus/hv_vss communication methods. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: util: introduce hv_utils_transport abstractionVitaly Kuznetsov2015-05-243-1/+328
| | | | | | | | | | | | | | | | | The intention is to make KVP/VSS drivers work through misc char devices. Introduce an abstraction for kernel/userspace communication to make the migration smoother. Transport operational mode (netlink or char device) is determined by the first received message. To support driver upgrades the switch from netlink to chardev operational mode is supported. Every hv_util daemon is supposed to register 2 callbacks: 1) on_msg() to get notified when the userspace daemon sent a message; 2) on_reset() to get notified when the userspace daemon drops the connection. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: fcopy: set .owner reference for file operationsVitaly Kuznetsov2015-05-241-4/+2
| | | | | | | | | | | Get an additional reference otherwise a crash is observed when hv_utils module is being unloaded while fcopy daemon is still running. .owner gives us an additional reference when someone holds a descriptor for the device. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: fcopy: switch to using the hvutil_device_state state machineVitaly Kuznetsov2015-05-241-40/+30
| | | | | | | | | | | | | | | | | | | | | | | Switch to using the hvutil_device_state state machine from using 3 different state variables: fcopy_transaction.active, opened, and in_hand_shake. State transitions are: -> HVUTIL_DEVICE_INIT when driver loads or on device release -> HVUTIL_READY if the handshake was successful -> HVUTIL_HOSTMSG_RECEIVED when there is a non-negotiation message from the host -> HVUTIL_USERSPACE_REQ after userspace daemon read the message -> HVUTIL_USERSPACE_RECV after/if userspace has replied -> HVUTIL_READY after we respond to the host -> HVUTIL_DEVICE_DYING on driver unload In hv_fcopy_onchannelcallback() process ICMSGTYPE_NEGOTIATE messages even when the userspace daemon is disconnected, otherwise we can make the host think we don't support FCOPY and disable the service completely. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vss: switch to using the hvutil_device_state state machineVitaly Kuznetsov2015-05-241-29/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | Switch to using the hvutil_device_state state machine from using kvp_transaction.active. State transitions are: -> HVUTIL_DEVICE_INIT when driver loads or on device release -> HVUTIL_READY if the handshake was successful -> HVUTIL_HOSTMSG_RECEIVED when there is a non-negotiation message from the host -> HVUTIL_USERSPACE_REQ after we sent the message to the userspace daemon -> HVUTIL_USERSPACE_RECV after/if the userspace daemon has replied -> HVUTIL_READY after we respond to the host -> HVUTIL_DEVICE_DYING on driver unload In hv_vss_onchannelcallback() process ICMSGTYPE_NEGOTIATE messages even when the userspace daemon is disconnected, otherwise we can make the host think we don't support VSS and disable the service completely. Unfortunately there is no good way we can figure out that the userspace daemon has died (unless we start treating all timeouts as such), add a protection against processing new VSS_OP_REGISTER messages while being in the middle of a transaction (HVUTIL_USERSPACE_REQ or HVUTIL_USERSPACE_RECV state). Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: kvp: switch to using the hvutil_device_state state machineVitaly Kuznetsov2015-05-241-38/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch to using the hvutil_device_state state machine from using 2 different state variables: kvp_transaction.active and in_hand_shake. State transitions are: -> HVUTIL_DEVICE_INIT when driver loads or on device release -> HVUTIL_READY if the handshake was successful -> HVUTIL_HOSTMSG_RECEIVED when there is a non-negotiation message from the host -> HVUTIL_USERSPACE_REQ after we sent the message to the userspace daemon -> HVUTIL_USERSPACE_RECV after/if the userspace daemon has replied -> HVUTIL_READY after we respond to the host -> HVUTIL_DEVICE_DYING on driver unload In hv_kvp_onchannelcallback() process ICMSGTYPE_NEGOTIATE messages even when the userspace daemon is disconnected, otherwise we can make the host think we don't support KVP and disable the service completely. Unfortunately there is no good way we can figure out that the userspace daemon has died (unless we start treating all timeouts as such). In case the daemon restarts we skip the negotiation procedure (so the daemon is supposed to has the same version). This behavior is unchanged from in_handshake approach. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: util: introduce state machine for util driversVitaly Kuznetsov2015-05-241-0/+9
| | | | | | | | | | | | KVP/VSS/FCOPY drivers work in fully serialized mode: we wait till userspace daemon registers, wait for a message from the host, send this message to the daemon, get the reply, send it back to host, wait for another message. Introduce enum hvutil_device_state to represend this state in all 3 drivers. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: fcopy: rename fcopy_work -> fcopy_timeout_workVitaly Kuznetsov2015-05-241-7/+7
| | | | | | | | | | | 'fcopy_work' (and fcopy_work_func) is a misnomer as it sounds like we expect this useful work to happen and in reality it is just an emergency escape when timeout happens. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: kvp: rename kvp_work -> kvp_timeout_workVitaly Kuznetsov2015-05-241-8/+8
| | | | | | | | | | | 'kvp_work' (and kvp_work_func) is a misnomer as it sounds like we expect this useful work to happen and in reality it is just an emergency escape when timeout happens. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vss: process deferred messages when we complete the transactionVitaly Kuznetsov2015-05-241-5/+9
| | | | | | | | | | | | | | In theory, the host is not supposed to issue any requests before be reply to the previous one. In KVP we, however, support the following scenarios: 1) A message was received before userspace daemon registered; 2) A message was received while the previous one is still being processed. In VSS we support only the former. Add support for the later, use hv_poll_channel() to do the job. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: fcopy: process deferred messages when we complete the transactionVitaly Kuznetsov2015-05-241-3/+9
| | | | | | | | | | | | | | In theory, the host is not supposed to issue any requests before be reply to the previous one. In KVP we, however, support the following scenarios: 1) A message was received before userspace daemon registered; 2) A message was received while the previous one is still being processed. In FCOPY we support only the former. Add support for the later, use hv_poll_channel() to do the job. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: kvp: move poll_channel() to hyperv_vmbus.hVitaly Kuznetsov2015-05-242-14/+15
| | | | | | | | | | Move poll_channel() to hyperv_vmbus.h and make it inline and rename it to hv_poll_channel() so it can be reused in other hv_util modules. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: kvp: reset kvp_contextVitaly Kuznetsov2015-05-241-0/+1
| | | | | | | | | | | | | | | We set kvp_context when we want to postpone receiving a packet from vmbus due to the previous transaction being unfinished. We, however, never reset this state, all consequent kvp_respond_to_host() calls will result in poll_channel() calling hv_kvp_onchannelcallback(). This doesn't cause real issues as: 1) Host is supposed to serialize transactions as well 2) If no message is pending vmbus_recvpacket() will return 0 recvlen. This is just a cleanup. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: util: move kvp/vss function declarations to hyperv_vmbus.hVitaly Kuznetsov2015-05-243-0/+11
| | | | | | | | | | These declarations are internal to hv_util module and hv_fcopy_* declarations already reside there. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX caseVitaly Kuznetsov2015-04-031-6/+7
| | | | | | | | | | | | | | | | | balloon_wrk.num_pages is __u32 and it comes from host in struct dm_balloon where it is also __u32. We, however, use 'int' in balloon_up() and in case we happen to receive num_pages>INT_MAX request we'll end up allocating zero pages as 'num_pages < alloc_unit' check in alloc_balloon_pages() will pass. Change num_pages type to unsigned int. In real life ballooning request come with num_pages in [512, 32768] range so this is more a future-proof/cleanup. Reported-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages caseVitaly Kuznetsov2015-04-031-1/+1
| | | | | | | | | | | | | | | | | 'Drivers: hv: hv_balloon: refuse to balloon below the floor' fix does not correctly handle the case when val.freeram < num_pages as val.freeram is __kernel_ulong_t and the 'val.freeram - num_pages' value will be a huge positive value instead of being negative. Usually host doesn't ask us to balloon more than val.freeram but in case he have a memory hog started after we post the last pressure report we can get into troubles. Suggested-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()Haiyang Zhang2015-04-031-2/+5
| | | | | | | | | | | | | Most of the retries can be done within a millisecond successfully, so we sleep 1ms before the first retry, then gradually increase the retry interval to 2^n with max value of 2048ms. Doing so, we will have shorter overall delay time, because most of the cases succeed within 1-2 attempts. Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: hv_balloon: survive ballooning request with num_pages=0Vitaly Kuznetsov2015-04-031-13/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ... and simplify alloc_balloon_pages() interface by removing redundant alloc_error from it. If we happen to enter balloon_up() with balloon_wrk.num_pages = 0 we will enter infinite 'while (!done)' loop as alloc_balloon_pages() will be always returning 0 and not setting alloc_error. We will also be sending a meaningless message to the host on every iteration. The 'alloc_unit == 1 && alloc_error -> num_ballooned == 0' change and alloc_error elimination requires a special comment. We do alloc_balloon_pages() with 2 different alloc_unit values and there are 4 different alloc_balloon_pages() results, let's check them all. alloc_unit = 512: 1) num_ballooned = 0, alloc_error = 0: we do 'alloc_unit=1' and retry pre- and post-patch. 2) num_ballooned > 0, alloc_error = 0: we check 'num_ballooned == num_pages' and act accordingly, pre- and post-patch. 3) num_ballooned > 0, alloc_error > 0: we report this chunk and remain within the loop, no changes here. 4) num_ballooned = 0, alloc_error > 0: we do 'alloc_unit=1' and retry pre- and post-patch. alloc_unit = 1: 1) num_ballooned = 0, alloc_error = 0: this can happen in two cases: when we passed 'num_pages=0' to alloc_balloon_pages() or when there was no space in bl_resp to place a single response. The second option is not possible as bl_resp is of PAGE_SIZE size and single response 'union dm_mem_page_range' is 8 bytes, but the first one is (in theory, I think that Hyper-V host never places such requests). Pre-patch code loops forever, post-patch code sends a reply with more_pages = 0 and finishes. 2) num_ballooned > 0, alloc_error = 0: we ran out of space in bl_resp, we report partial success and remain within the loop, no changes pre- and post-patch. 3) num_ballooned > 0, alloc_error > 0: pre-patch code finishes, post-patch code does one more try and if there is no progress (we finish with 'num_ballooned = 0') we finish. So we try a bit harder with this patch. 4) num_ballooned = 0, alloc_error > 0: both pre- and post-patch code enter 'more_pages = 0' branch and finish. So this patch has two real effects: 1) We reply with an empty response to 'num_pages=0' request. 2) We try a bit harder on alloc_unit=1 allocations (and reply with an empty tail reply in case we fail). An empty reply should be supported by host as we were able to send it even with pre-patch code when we were not able to allocate a single page. Suggested-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor functionVitaly Kuznetsov2015-04-031-4/+4
| | | | | | | | | | | | | | | | | | | | | Commit 79208c57da53 ("Drivers: hv: hv_balloon: Make adjustments in computing the floor") was inacurate as it introduced a jump in our piecewiese linear 'floor' function: At 2048MB we have: Left limit: 104 + 2048/8 = 360 Right limit: 256 + 2048/16 = 384 (so the right value is 232) We now have to make an adjustment at 8192 boundary: 232 + 8192/16 = 744 512 + 8192/32 = 768 (so the right value is 488) Suggested-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: hv_balloon: do not online pages in offline blocksVitaly Kuznetsov2015-04-031-1/+11
| | | | | | | | | | | | | | | | | | | Currently we add memory in 128Mb blocks but the request from host can be aligned differently. In such case we add a partially backed block and when this block goes online we skip onlining pages which are not backed (hv_online_page() callback serves this purpose). When we receive next request for the same host add region we online pages which were not backed before with hv_bring_pgs_online(). However, we don't check if the the block in question was onlined and online this tail unconditionally. This is bad as we avoid all online_pages() logic: these pages are not accounted, we don't send notifications (and hv_balloon is not the only receiver of them),... And, first of all, nobody asked as to online these pages. Solve the issue by checking if the last previously backed page was onlined and onlining the tail only in case it was. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hv: remove the per-channel workqueueDexuan Cui2015-04-031-29/+1
| | | | | | | | | | It's not necessary any longer, since we can safely run the blocking message handlers in vmbus_connection.work_queue now. Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()Dexuan Cui2015-04-033-135/+30
| | | | | | | | | | | | | Since the 2 fucntions can safely run in vmbus_connection.work_queue without hang, we don't need to schedule new work items into the per-channel workqueue. Actally we can even remove the per-channel workqueue now -- we'll do it in the next patch. Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hv: run non-blocking message handlers in the dispatch taskletDexuan Cui2015-04-033-26/+53
| | | | | | | | | | | | | | | | | | | | | | | A work item in vmbus_connection.work_queue can sleep, waiting for a new host message (usually it is some kind of "completion" message). Currently the new message will be handled in the same workqueue, but since work items in the workqueue is serialized, we actually have no chance to handle the new message if the current work item is sleeping -- as as result, the current work item will hang forever. K. Y. has posted the below fix to resolve the issue: Drivers: hv: vmbus: Perform device register in the per-channel work element Actually we can simplify the fix by directly running non-blocking message handlers in the dispatch tasklet (inspired by K. Y.). This patch is the fundamental change. The following 2 patches will simplify the message offering and rescind-offering handling a lot. Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Don't wait after requesting offersK. Y. Srinivasan2015-03-261-11/+0
| | | | | | | | | Don't wait after sending request for offers to the host. This wait is unnecessary and simply adds 5 seconds to the boot time. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Fix a siganlling host signalling issueK. Y. Srinivasan2015-03-251-2/+26
| | | | | | | | | | Handle the case when the write to the ringbuffer fails. In this case, unconditionally signal the host. Since we may have deferred signalling the host based on the kick_q parameter, signalling the host unconditionally in this case deals with the issue. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Export the vmbus_sendpacket_pagebuffer_ctl()K. Y. Srinivasan2015-03-251-0/+1
| | | | | | | | Export the vmbus_sendpacket_pagebuffer_ctl() interface. This export will be used by the netvsc driver. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Fix a bug in rescind processing in vmbus_close_internal()K. Y. Srinivasan2015-03-251-9/+6
| | | | | | | | | | | | | | When a channel has been rescinded, the close operation is a noop. Restructure the code so we deal with the rescind condition after we properly cleanup the channel. I would like to thank Dexuan Cui <decui@microsoft.com> for observing this problem. The current code leaks memory when the channel is rescinded. The current char-next branch is broken and this patch fixes the bug. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hv: vmbus: missing curly braces in vmbus_process_offer()Dan Carpenter2015-03-251-1/+2
| | | | | | | | | The indenting makes it clear that there were curly braces intended here. Fixes: 2dd37cb81580 ('Drivers: hv: vmbus: Handle both rescind and offer messages in the same context') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: vmbus: Correcting truncation error for constant ↵Nick Meier2015-03-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HV_CRASH_CTL_CRASH_NOTIFY HV_CRASH_CTL_CRASH_NOTIFY is a 64 bit number. Depending on the usage context, the value may be truncated. This patch is in response from the following email from Wu Fengguang <fengguang.wu@intel.com>: From: Wu Fengguang <fengguang.wu@intel.com> Subject: [char-misc:char-misc-testing 25/45] drivers/hv/vmbus_drv.c:67:9: sparse: constant 0x8000000000000000 is so big it is unsigned long tree: git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git char-misc-testing head: b3de8e3719e582f3182bb504295e4a8e43c8c96f commit: 96c1d0581d00f7abe033350edb021a9d947d8d81 [25/45] Drivers: hv: vmbus: Add support for VMBus panic notifier handler reproduce: # apt-get install sparse git checkout 96c1d0581d00f7abe033350edb021a9d947d8d81 make ARCH=x86_64 allmodconfig make C=1 CF=-D__CHECK_ENDIAN__ sparse warnings: (new ones prefixed by >>) drivers/hv/vmbus_drv.c:67:9: sparse: constant 0x8000000000000000 is so big it is unsigned long ... Signed-off-by: Nick Meier <nmeier@microsoft.com> Reported-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Drivers: hv: hv_balloon: don't lose memory when onlining order is not naturalVitaly Kuznetsov2015-03-251-10/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Memory blocks can be onlined in random order. When this order is not natural some memory pages are not onlined because of the redundant check in hv_online_page(). Here is a real world scenario: 1) Host tries to hot-add the following (process_hot_add): pg_start=rg_start=0x48000, pfn_cnt=111616, rg_size=262144 2) This results in adding 4 memory blocks: [ 109.057866] init_memory_mapping: [mem 0x48000000-0x4fffffff] [ 114.102698] init_memory_mapping: [mem 0x50000000-0x57ffffff] [ 119.168039] init_memory_mapping: [mem 0x58000000-0x5fffffff] [ 124.233053] init_memory_mapping: [mem 0x60000000-0x67ffffff] The last one is incomplete but we have special has->covered_end_pfn counter to avoid onlining non-backed frames and hv_bring_pgs_online() function to bring them online later on. 3) Now we have 4 offline memory blocks: /sys/devices/system/memory/memory9-12 $ for f in /sys/devices/system/memory/memory*/state; do echo $f `cat $f`; done | grep -v onlin /sys/devices/system/memory/memory10/state offline /sys/devices/system/memory/memory11/state offline /sys/devices/system/memory/memory12/state offline /sys/devices/system/memory/memory9/state offline 4) We bring them online in non-natural order: $grep MemTotal /proc/meminfo MemTotal: 966348 kB $echo online > /sys/devices/system/memory/memory12/state && grep MemTotal /proc/meminfo MemTotal: 1019596 kB $echo online > /sys/devices/system/memory/memory11/state && grep MemTotal /proc/meminfo MemTotal: 1150668 kB $echo online > /sys/devices/system/memory/memory9/state && grep MemTotal /proc/meminfo MemTotal: 1150668 kB As you can see memory9 block gives us zero additional memory. We can also observe a huge discrepancy between host- and guest-reported memory sizes. The root cause of the issue is the redundant pg >= covered_start_pfn check (and covered_start_pfn advancing) in hv_online_page(). When upper memory block in being onlined before the lower one (memory12 and memory11 in the above case) we advance the covered_start_pfn pointer and all memory9 pages do not pass the check. If the assumption that host always gives us requests in sequential order and pg_start always equals rg_start when the first request for the new HA region is received (that's the case in my testing) is correct than we can get rid of covered_start_pfn and pg >= start_pfn check in hv_online_page() is sufficient. The current char-next branch is broken and this patch fixes the bug. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-22 21:14:49 +0100