| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Cypress TrueTouch(tm) Standard Product controllers,
Generation4 devices, SPI adapter module.
This driver adds communication support with TTSP controller
using SPI bus.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Cypress TrueTouch(tm) Standard Product controllers,
Generation4 devices, I2C adapter module.
This driver adds communication support with TTSP controller
using I2C bus.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Cypress TrueTouch(tm) Standard Product controllers,
Generetion4 devices, Core driver.
Core driver is interface between host and TTSP controller and processes
data sent by controller.
Responsibilities of module are IRQ handling, reading system information
registers and sending multi-touch protocol type B events.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Existing I2C code is for TrueTouch Gen3 devices
TrueTouch Gen4 device is using same protocol, will split driver into
two pieces to use common code with both drivers.
Read/Write functions parameter list modified, since shared code will
be used by two separate drivers and these drivers are not sharing same
structs, parameters updated to use common structures.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The OLPC XO-1.75 and XO-4 laptops include a PS/2 touchpad and an AT
keyboard, yet they do not have a hardware PS/2 controller. Instead, a
firmware runs on a dedicated core ("Security Processor", part of the SoC)
that acts as a PS/2 controller through bit-banging.
Communication between the main cpu (Application Processor) and the
Security Processor happens via a standard command mechanism implemented
by the SoC. Add a driver for this interface to enable keyboard/mouse
input on this platform.
Original author: Saadia Baloch
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Although BTN_TOOL_PEN and BTN_TOOL_RUBBER functioned properly, the driver
didn't have hover functionality, so it's been added.
Also, "WACOM_RETRY_CNT" was not used, so it was removed.
Signed-off-by: Tatsunosuke Tobita <tobita.tatsunosuke@wacom.co.jp>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It should not be changed by the driver, so let's make it const pointer.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
pxa27x-keypad includes matrix keys. Make use of matrix_keymap
for the matrix keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is effectively already in force through input_mt_init_slots, and uinput
too ignores the actual minimum.
Since slots are a kernel-genenerated axis only, non-zero minimums make
little sense and are likely to cause errors. Better to treat a non-zero
minimum as kernel bug if it ever happens.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
|
|
If userspace requests current KEY-state, they very likely assume that no
such events are pending in the output queue of the evdev device.
Otherwise, they will parse events which they already handled via
EVIOCGKEY(). For XKB applications this can cause irreversible keyboard
states if a modifier is locked multiple times because a CTRL-DOWN event is
handled once via EVIOCGKEY() and once from the queue via read(), even
though it should handle it only once.
Therefore, lets do the only logical thing and flush the evdev queue
atomically during this ioctl. We only flush events that are affected by
the given ioctl.
This only affects boolean events like KEY, SND, SW and LED. ABS, REL and
others are not affected as duplicate events can be handled gracefully by
user-space.
Note: This actually breaks semantics of the evdev ABI. However,
investigations showed that userspace already expects the new semantics and
we end up fixing at least all XKB applications.
All applications that are aware of this race-condition mirror the KEY
state for each open-file and detect/drop duplicate events. Hence, they do
not care whether duplicates are posted or not and work fine with this fix.
Also note that we need proper locking to guarantee atomicity and avoid
dead-locks. event_lock must be locked before queue_lock (see input-core).
However, we can safely release event_lock while flushing the queue. This
allows the input-core to proceed with pending events and only stop if it
needs our queue_lock to post new events.
This should guarantee that we don't block event-dispatching for too long
while flushing a single event queue.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
|
|
This patch fixes warnings due to missing lock on write error path.
WARNING: at fs/hpfs/hpfs_fn.h:353 hpfs_truncate+0x75/0x80 [hpfs]()
Hardware name: empty
Pid: 26563, comm: dd Tainted: P O 3.9.4 #12
Call Trace:
hpfs_truncate+0x75/0x80 [hpfs]
hpfs_write_begin+0x84/0x90 [hpfs]
_hpfs_bmap+0x10/0x10 [hpfs]
generic_file_buffered_write+0x121/0x2c0
__generic_file_aio_write+0x1c7/0x3f0
generic_file_aio_write+0x7c/0x100
do_sync_write+0x98/0xd0
hpfs_file_write+0xd/0x50 [hpfs]
vfs_write+0xa2/0x160
sys_write+0x51/0xa0
page_fault+0x22/0x30
system_call_fastpath+0x1a/0x1f
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The irqdomain core will report a log message for any attempted map call
that fails unless the error code is -EPERM. This patch changes the
Versatile irq controller drivers to use -EPERM because it is normal for
a subset of the IRQ inputs to be marked as reserved on the various
Versatile platforms.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Commit 9f29ab11ddbf ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600. Tony says:
"It panics with the message:
Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel
[...] my problem comes from arch/ia64/hp/common/sba_iommu.c
where the code in sba_init() says:
acpi_bus_register_driver(&acpi_sba_ioc_driver);
if (!ioc_list) {
but because of this change we never managed to call ioc_init()
so ioc_list doesn't get set up, and we die."
Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled. Avoid this hang by calling
debug_ll_io_init() early.
Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io(). After this patch the hang goes away.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.
Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.
With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When user interrupts ongoing transfers the dmatest may end up with console
lockup, oops, or data mismatch. This patch prevents user to abort any ongoing
test.
Documentation is updated accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Commit b378549 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them. That turned out to break Toshiba P870-303,
however, so revert that code.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58201
Reported-and-tested-by: Jerome Cantenot <jerome.cantenot@gmail.com>
Tracked-down-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Attempt to reboot the system gracefully when a key combo is detected.
If the reste combination is pressed the 2nd time we assume that graceful
reboot failed and perform emergency reboot. This fucntionality is useful
when UI is stuck but the system is otherwise working fine.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
I broke them in this commit:
commit 1be374a0518a288147c6a7398792583200a67261
Author: Andy Lutomirski <luto@amacapital.net>
Date: Wed May 22 14:07:44 2013 -0700
net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg
This patch adds __sys_sendmsg and __sys_sendmsg as common helpers that accept
MSG_CMSG_COMPAT and blocks MSG_CMSG_COMPAT at the syscall entrypoints. It
also reverts some unnecessary checks in sys_socketcall.
Apparently I was suffering from underscore blindness the first time around.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The irqsoff tracer records the max time that interrupts are disabled.
There are hooks in the assembly code that calls back into the tracer when
interrupts are disabled or enabled.
When they are enabled, the tracer checks if the amount of time they
were disabled is larger than the previous recorded max interrupts off
time. If it is, it creates a snapshot of the currently running trace
to store where the last largest interrupts off time was held and how
it happened.
During testing, this RCU lockdep dump appeared:
[ 1257.829021] ===============================
[ 1257.829021] [ INFO: suspicious RCU usage. ]
[ 1257.829021] 3.10.0-rc1-test+ #171 Tainted: G W
[ 1257.829021] -------------------------------
[ 1257.829021] /home/rostedt/work/git/linux-trace.git/include/linux/rcupdate.h:780 rcu_read_lock() used illegally while idle!
[ 1257.829021]
[ 1257.829021] other info that might help us debug this:
[ 1257.829021]
[ 1257.829021]
[ 1257.829021] RCU used illegally from idle CPU!
[ 1257.829021] rcu_scheduler_active = 1, debug_locks = 0
[ 1257.829021] RCU used illegally from extended quiescent state!
[ 1257.829021] 2 locks held by trace-cmd/4831:
[ 1257.829021] #0: (max_trace_lock){......}, at: [<ffffffff810e2b77>] stop_critical_timing+0x1a3/0x209
[ 1257.829021] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff810dae5a>] __update_max_tr+0x88/0x1ee
[ 1257.829021]
[ 1257.829021] stack backtrace:
[ 1257.829021] CPU: 3 PID: 4831 Comm: trace-cmd Tainted: G W 3.10.0-rc1-test+ #171
[ 1257.829021] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007
[ 1257.829021] 0000000000000001 ffff880065f49da8 ffffffff8153dd2b ffff880065f49dd8
[ 1257.829021] ffffffff81092a00 ffff88006bd78680 ffff88007add7500 0000000000000003
[ 1257.829021] ffff88006bd78680 ffff880065f49e18 ffffffff810daebf ffffffff810dae5a
[ 1257.829021] Call Trace:
[ 1257.829021] [<ffffffff8153dd2b>] dump_stack+0x19/0x1b
[ 1257.829021] [<ffffffff81092a00>] lockdep_rcu_suspicious+0x109/0x112
[ 1257.829021] [<ffffffff810daebf>] __update_max_tr+0xed/0x1ee
[ 1257.829021] [<ffffffff810dae5a>] ? __update_max_tr+0x88/0x1ee
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810dbf85>] update_max_tr_single+0x11d/0x12d
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810e2b15>] stop_critical_timing+0x141/0x209
[ 1257.829021] [<ffffffff8109569a>] ? trace_hardirqs_on+0xd/0xf
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810e3057>] time_hardirqs_on+0x2a/0x2f
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff8109550c>] trace_hardirqs_on_caller+0x16/0x197
[ 1257.829021] [<ffffffff8109569a>] trace_hardirqs_on+0xd/0xf
[ 1257.829021] [<ffffffff811002b9>] user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810029b4>] do_notify_resume+0x92/0x97
[ 1257.829021] [<ffffffff8154bdca>] int_signal+0x12/0x17
What happened was entering into the user code, the interrupts were enabled
and a max interrupts off was recorded. The trace buffer was saved along with
various information about the task: comm, pid, uid, priority, etc.
The uid is recorded with task_uid(tsk). But this is a macro that uses rcu_read_lock()
to retrieve the data, and this happened to happen where RCU is blind (user_enter).
As only the preempt and irqs off tracers can have this happen, and they both
only have the tsk == current, if tsk == current, use current_uid() instead of
task_uid(), as current_uid() does not use RCU as only current can change its uid.
This fixes the RCU suspicious splat.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The limit of 25 ACL entries is arbitrary, but baked into the on-disk
format. For version 5 superblocks, increase it to the maximum nuber
of ACLs that can fit into a single xattr.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Mark Tinguely <tinuguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 5c87d4bc1a86bd6e6754ac3d6e111d776ddcfe57)
|
|
attr2 format is always enabled for v5 superblock filesystems, so the
mount options to enable or disable it need to be cause mount errors.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit d3eaace84e40bf946129e516dcbd617173c1cf14)
|
|
The inode unlinked list manipulations operate directly on the inode
buffer, and so bypass the inode CRC calculation mechanisms. Hence an
inode on the unlinked list has an invalid CRC. Fix this by
recalculating the CRC whenever we modify an unlinked list pointer in
an inode, ncluding during log recovery. This is trivial to do and
results in unlinked list operations always leaving a consistent
inode in the buffer.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 0a32c26e720a8b38971d0685976f4a7d63f9e2ef)
|
|
There are several constraints that inode allocation and unlink
logging impose on log recovery. These all stem from the fact that
inode alloc/unlink are logged in buffers, but all other inode
changes are logged in inode items. Hence there are ordering
constraints that recovery must follow to ensure the correct result
occurs.
As it turns out, this ordering has been working mostly by chance
than good management. The existing code moves all buffers except
cancelled buffers to the head of the list, and everything else to
the tail of the list. The problem with this is that is interleaves
inode items with the buffer cancellation items, and hence whether
the inode item in an cancelled buffer gets replayed is essentially
left to chance.
Further, this ordering causes problems for log recovery when inode
CRCs are enabled. It typically replays the inode unlink buffer long before
it replays the inode core changes, and so the CRC recorded in an
unlink buffer is going to be invalid and hence any attempt to
validate the inode in the buffer is going to fail. Hence we really
need to enforce the ordering that the inode alloc/unlink code has
expected log recovery to have since inode chunk de-allocation was
introduced back in 2003...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit a775ad778073d55744ed6709ccede36310638911)
|
|
When invalidating an attribute leaf block block, there might be
remote attributes that it points to. With the recent rework of the
remote attribute format, we have to make sure we calculate the
length of the attribute correctly. We aren't doing that in
xfs_attr3_leaf_inactive(), so fix it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Mark Tinguely <tinuguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 59913f14dfe8eb772ff93eb442947451b4416329)
|
|
Calculating dquot CRCs when the backing buffer is written back just
doesn't work reliably. There are several places which manipulate
dquots directly in the buffers, and they don't calculate CRCs
appropriately, nor do they always set the buffer up to calculate
CRCs appropriately.
Firstly, if we log a dquot buffer (e.g. during allocation) it gets
logged without valid CRC, and so on recovery we end up with a dquot
that is not valid.
Secondly, if we recover/repair a dquot, we don't have a verifier
attached to the buffer and hence CRCs are not calculated on the way
down to disk.
Thirdly, calculating the CRC after we've changed the contents means
that if we re-read the dquot from the buffer, we cannot verify the
contents of the dquot are valid, as the CRC is invalid.
So, to avoid all the dquot CRC errors that are being detected by the
read verifier, change to using the same model as for inodes. That
is, dquot CRCs are calculated and written to the backing buffer at
the time the dquot is flushed to the backing buffer. If we modify
the dquot directly in the backing buffer, calculate the CRC
immediately after the modification is complete. Hence the dquot in
the on-disk buffer should always have a valid CRC.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 6fcdc59de28817d1fbf1bd58cc01f4f3fac858fb)
|
|
On RT5350 the memory size is set to Bytes and not MegaBytes due to a missing
multiplier.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5378/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
cputime_to_timeval() takes a struct timeval *as its second argument but
a struct compat_timeval * will be passed resulting in:
CC arch/mips/kernel/binfmt_elfn32.o
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c: In function ‘fill_prstatus’:
arch/mips/kernel/../../../fs/binfmt_elf.c:1330:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1331:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1336:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1337:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1339:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1340:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
AS arch/mips/kernel/scall64-n32.o
CC arch/mips/kernel/signal_n32.o
CC arch/mips/kernel/binfmt_elfo32.o
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c: In function ‘fill_prstatus’:
arch/mips/kernel/../../../fs/binfmt_elf.c:1330:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1331:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1336:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1337:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1339:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1340:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
from include/linux/sched.h:28,
from include/linux/ptrace.h:5,
from include/uapi/linux/elfcore.h:7,
from include/linux/elfcore.h:7,
from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
As noted by Wladislav Wiebe:
$ halt
..
Sent SIGKILL to all processes
Requesting system halt
[66.729373] System halted.
[66.733244]
[66.734761] =====================================
[66.739473] [ BUG: lock held at task exit time! ]
[66.744188] 3.8.7-0-sampleversion-fct #49 Tainted: G O
[66.750202] -------------------------------------
[66.754913] init/21479 is exiting with locks still held!
[66.760234] 1 lock held by init/21479:
[66.763990] #0: (reboot_mutex){+.+...}, at: [<ffffffff801776c8>] SyS_reboot+0xe0/0x218
[66.772165]
[66.772165] stack backtrace:
[66.776532] Call Trace:
[66.778992] [<ffffffff805780a8>] dump_stack+0x8/0x34
[66.783972] [<ffffffff801618b0>] do_exit+0x610/0xa70
[66.788948] [<ffffffff801777a8>] SyS_reboot+0x1c0/0x218
[66.794186] [<ffffffff8013d6a4>] handle_sys64+0x44/0x64
This is an alternative fix to the one sent by Wladislav. We kill the
watchdog for each CPU and then spin in WAIT with interrupts disabled.
This is the lowest power mode for the OCTEON. If we were to spin with
interrupts enabled, we would get a continual stream of warning messages
and backtraces from the lockup detector, so I chose to disable
interrupts.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Maxim Uvarov <muvarov@gmail.com>
Cc: Wladislav Wiebe <wladislav.kw@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/5324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
arch/mips/kernel/rtlx.c: In function 'rtlx_module_init':
arch/mips/kernel/rtlx.c:523:3: error: implicit declaration of function 'set_vi_handler' [-Werror=implicit-function-declaration]
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If pdata is NULL, atmel_tsadcc_probe() will release all the resources
and return 0, but we need a error code is returned in this case.
Fix to return -EINVAL and move the check for pdata to the begin
of this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Since the introduction of preemptible mmu_gather TLB fast mode has been
broken. TLB fast mode relies on there being absolutely no concurrency;
it frees pages first and invalidates TLBs later.
However now we can get concurrency and stuff goes *bang*.
This patch removes all tlb_fast_mode() code; it was found the better
option vs trying to patch the hole by entangling tlb invalidation with
the scheduler.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
f9a37be0f0 ("x86: Use PCI setup data") added support for using PCI ROM
images from setup_data. This used phys_to_virt(), which is not valid for
highmem addresses, and can cause a crash when booting a 32-bit kernel via
the EFI boot stub.
pcibios_add_device() assumes that the physical addresses stored in
setup_data are accessible via the direct kernel mapping, and that calling
phys_to_virt() is valid. This isn't guaranteed to be true on x86 where the
direct mapping range is much smaller than on x86-64.
Calling phys_to_virt() on a highmem address results in the following:
BUG: unable to handle kernel paging request at 39a3c198
IP: [<c262be0f>] pcibios_add_device+0x2f/0x90
...
Call Trace:
[<c2370c73>] pci_device_add+0xe3/0x130
[<c274640b>] pci_scan_single_device+0x8b/0xb0
[<c2370d08>] pci_scan_slot+0x48/0x100
[<c2371904>] pci_scan_child_bus+0x24/0xc0
[<c262a7b0>] pci_acpi_scan_root+0x2c0/0x490
[<c23b7203>] acpi_pci_root_add+0x312/0x42f
...
The solution is to use ioremap() instead of phys_to_virt() to map the
setup data into the kernel address space.
[bhelgaas: changelog]
Tested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org # v3.8+
|
|
Fix regression introduced by commit 143d9d9616 ("USB: serial: add
tiocmiwait subdriver operation") which made the ioctl operation return
ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT
implementation is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
devtmpfs_delete_node() calls devnode() callback with mode==NULL but
vfio still tries to write there.
The patch fixes this.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
clk_set_rate() isn't supposed to accept approximate frequencies, instead
a supported frequency should be obtained from clk_round_rate() and then
used to set the clock.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Jiri Kosina <jkosina@suse.cz> and Borislav Petkov <bp@alien8.de>
reported the warning:
[ 51.616759] ------------[ cut here ]------------
[ 51.621460] WARNING: at arch/x86/kernel/smp.c:123 native_smp_send_reschedule+0x58/0x60()
[ 51.629638] Modules linked in: ext2 vfat fat loop snd_hda_codec_hdmi usbhid snd_hda_codec_realtek coretemp kvm_intel kvm snd_hda_intel snd_hda_codec crc32_pclmul crc32c_intel ghash_clmulni_intel snd_hwdep snd_pcm aesni_intel sb_edac aes_x86_64 ehci_pci snd_page_alloc glue_helper snd_timer xhci_hcd snd iTCO_wdt iTCO_vendor_support ehci_hcd edac_core lpc_ich acpi_cpufreq lrw gf128mul ablk_helper cryptd mperf usbcore usb_common soundcore mfd_core dcdbas evdev pcspkr processor i2c_i801 button microcode
[ 51.675581] CPU: 0 PID: 244 Comm: kworker/1:1 Tainted: G W 3.10.0-rc1+ #10
[ 51.683407] Hardware name: Dell Inc. Precision T3600/0PTTT9, BIOS A08 01/24/2013
[ 51.690901] Workqueue: events od_dbs_timer
[ 51.695069] 0000000000000009 ffff88043a2f5b68 ffffffff8161441c ffff88043a2f5ba8
[ 51.702602] ffffffff8103e540 0000000000000033 0000000000000001 ffff88043d5f8000
[ 51.710136] 00000000ffff0ce1 0000000000000001 ffff88044fc4fc08 ffff88043a2f5bb8
[ 51.717691] Call Trace:
[ 51.720191] [<ffffffff8161441c>] dump_stack+0x19/0x1b
[ 51.725396] [<ffffffff8103e540>] warn_slowpath_common+0x70/0xa0
[ 51.731473] [<ffffffff8103e58a>] warn_slowpath_null+0x1a/0x20
[ 51.737378] [<ffffffff81025628>] native_smp_send_reschedule+0x58/0x60
[ 51.744013] [<ffffffff81072cfd>] wake_up_nohz_cpu+0x2d/0xa0
[ 51.749745] [<ffffffff8104f6bf>] add_timer_on+0x8f/0x110
[ 51.755214] [<ffffffff8105f6fe>] __queue_delayed_work+0x16e/0x1a0
[ 51.761470] [<ffffffff8105f251>] ? try_to_grab_pending+0xd1/0x1a0
[ 51.767724] [<ffffffff8105f78a>] mod_delayed_work_on+0x5a/0xa0
[ 51.773719] [<ffffffff814f6b5d>] gov_queue_work+0x4d/0xc0
[ 51.779271] [<ffffffff814f60cb>] od_dbs_timer+0xcb/0x170
[ 51.784734] [<ffffffff8105e75d>] process_one_work+0x1fd/0x540
[ 51.790634] [<ffffffff8105e6f2>] ? process_one_work+0x192/0x540
[ 51.796711] [<ffffffff8105ef22>] worker_thread+0x122/0x380
[ 51.802350] [<ffffffff8105ee00>] ? rescuer_thread+0x320/0x320
[ 51.808264] [<ffffffff8106634a>] kthread+0xea/0xf0
[ 51.813200] [<ffffffff81066260>] ? flush_kthread_worker+0x150/0x150
[ 51.819644] [<ffffffff81623d5c>] ret_from_fork+0x7c/0xb0
[ 51.918165] nouveau E[ DRM] GPU lockup - switching to software fbcon
[ 51.930505] [<ffffffff81066260>] ? flush_kthread_worker+0x150/0x150
[ 51.936994] ---[ end trace f419538ada83b5c5 ]---
It was caused by the policy->cpus changed during the process of
__gov_queue_work(), in other word, cpu offline happened.
Use get/put_online_cpus() to prevent the offline from happening while
__gov_queue_work() is running.
[rjw: The problem has been present since recent commit 031299b
(cpufreq: governors: Avoid unnecessary per cpu timer interrupts)]
References: https://lkml.org/lkml/2013/6/5/88
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
With the introduction of ACPI scan handlers, an ACPI device object
with an ACPI scan handler attached to it must not be bound to an ACPI
driver any more. Therefore it doesn't make sense to match those
ACPI device objects against a newly registered ACPI driver in
acpi_bus_match(), so make that function return 0 if the device
object passed to it has an ACPI scan handler attached.
This also addresses a regression related to a broken ACPI table in
the BIOS, where it has defined a _ROM method under the PCI root
bridge object. This causes the video module to treat that object
as a display controller device (since only display devices are
supposed to have a _ROM method defined according to the ACPI spec).
As a result, the ACPI video driver binds to the PCI root bridge
object and overwrites the previously assigned driver_data field of
it, causing subsequent calls to acpi_get_pci_dev() to fail.
[rjw: Subject and changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091
Reported-by: Jason Cassell <bluesloth600@gmail.com>
Reported-and-bisected-by: Dmitry S. Demin <dmitryy.demin@gmail.com>
Cc: 3.9+ <stable@kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix to return a negative error code in the acpi_gsi_to_irq() and
request_irq() error handling case instead of 0, as done elsewhere
in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 4b31e774 (Always set P-state on initialization) fixed bug
#4634 and caused the driver to always set the target P-State at
least once since the initial P-State may not be the desired one.
Commit 5a1c0228 (cpufreq: Avoid calling cpufreq driver's target()
routine if target_freq == policy->cur) caused a regression in
this behavior.
This fixes the regression by setting policy->cur based on the CPU's
target frequency rather than the CPU's current reported frequency
(which may be different). This means that the P-State will be set
initially if the CPU's target frequency is different from the
governor's target frequency.
This fixes an issue where setting the default governor to
performance wouldn't correctly enable turbo mode on all cores.
Signed-off-by: Ross Lagerwall <rosslagerwall@gmail.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.8+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
