summaryrefslogtreecommitdiffstats
path: root/drivers/i2c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* i2c: xiic: Make the start and the byte count write atomicShubhrajyoti Datta2018-09-061-0/+4
| | | | | | | | | | | | | | | | | | | | Disable interrupts while configuring the transfer and enable them back. We have below as the programming sequence 1. start and slave address 2. byte count and stop In some customer platform there was a lot of interrupts between 1 and 2 and after slave address (around 7 clock cyles) if 2 is not executed then the transaction is nacked. To fix this case make the 2 writes atomic. Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [wsa: added a newline for better readability] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
* i2c: i801: fix DNV's SMBCTRL register offsetFelipe Balbi2018-09-041-1/+6
| | | | | | | | | | | | DNV's iTCO is slightly different with SMBCTRL sitting at a different offset when compared to all other devices. Let's fix so that we can properly use iTCO watchdog. Fixes: 84d7f2ebd70d ("i2c: i801: Add support for Intel DNV") Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: imx-lpi2c: Remove mx8dv compatible entryFabio Estevam2018-09-021-1/+0
| | | | | | | | | mx8dv never entered into production and there is no other place in the kernel referring to this SoC, so remove it from the driver's compatible entry. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: uniphier-f: issue STOP only for last message or I2C_M_STOPMasahiro Yamada2018-09-021-5/+2
| | | | | | | | | | | | | | This driver currently emits a STOP if the next message is not I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR ioctl, where read/write transactions are combined without STOP between. Issue STOP only when the message is the last one _or_ flagged with I2C_M_STOP. Fixes: 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: uniphier: issue STOP only for last message or I2C_M_STOPMasahiro Yamada2018-09-021-5/+2
| | | | | | | | | | | | | | This driver currently emits a STOP if the next message is not I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR ioctl, where read/write transactions are combined without STOP between. Issue STOP only when the message is the last one _or_ flagged with I2C_M_STOP. Fixes: dd6fd4a32793 ("i2c: uniphier: add UniPhier FIFO-less I2C driver") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: sh_mobile: fix leak when using DMA bounce bufferWolfram Sang2018-08-301-2/+4
| | | | | | | | | | | We only freed the bounce buffer after successful DMA, missing the cases where DMA setup may have gone wrong. Use a better location which always gets called after each message and use 'stop_after_dma' as a flag for a successful transfer. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: sh_mobile: define start_ch() void as it only returns 0 anyhowWolfram Sang2018-08-301-6/+3
| | | | | | | | | | | After various refactoring over the years, start_ch() doesn't return errno anymore, so make the function return void. This saves the error handling when calling it which in turn eases cleanup of resources of a future patch. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: refactor function to release a DMA safe bufferWolfram Sang2018-08-302-6/+7
| | | | | | | | | | | | | | | | a) rename to 'put' instead of 'release' to match 'get' when obtaining the buffer b) change the argument order to have the buffer as first argument c) add a new argument telling the function if the message was transferred. This allows the function to be used also in cases where setting up DMA failed, so the buffer needs to be freed without syncing to the message buffer. Also convert the only user. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: algos: bit: make the error messages grepableJan Kundrát2018-08-301-24/+31
| | | | | | | | Yep, I went looking for one of these, and I wasn't able to find it easily. That's worse than a line which is 82-chars long, IMHO. Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: designware: Re-init controllers with pm_disabled set on resumeHans de Goede2018-08-302-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C busses which the OS shares with the PUNIT as these need special handling. Until now we called dev_pm_syscore_device(dev, true) for I2C controllers with this flag set to keep these I2C controllers always on. After commit 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation"), this no longer works. This commit modifies lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran before it, so that it does not run on a resume from hibernate (or from S3). On these systems the conditions for lpss_iosf_enter_d3_state() to run never become true, so lpss_iosf_exit_d3_state() never gets called and the 2 LPSS DMA controllers never get forced into D0 mode, instead they are left in their default automatic power-on when needed mode. The not forcing of D0 mode for the DMA controllers enables these systems to properly enter S0ix modes, which is a good thing. But after entering S0ix modes the I2C controller connected to the PMIC no longer works, leading to e.g. broken battery monitoring. The _PS3 method for this I2C controller looks like this: Method (_PS3, 0, NotSerialized) // _PS3: Power State 3 { If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06))) { Return (Zero) } PSAT |= 0x03 Local0 = PSAT /* \_SB_.I2C5.PSAT */ } Where PMID = 0x05, so we enter the Return (Zero) path on these systems. So even if we were to not call dev_pm_syscore_device(dev, true) the I2C controller will be left in D0 rather then be switched to D3. Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all* I2C controllers are in D3 mode. This combined with the I2C controller no longer working now that we reach S0ix states on these systems leads to me believing that the PUNIT itself puts the I2C controller in D3 when all other conditions for entering S0ix states are true. Since now the I2C controller is put in D3 over a suspend/resume we must re-initialize it afterwards and that does indeed fix it no longer working. This commit implements this fix by: 1) Making the suspend_late callback a no-op if pm_disabled is set and making the resume_early callback skip the clock re-enable (since it now was not disabled) while still doing the necessary I2C controller re-init. 2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend and resume callbacks are actually called. Normally this would cause the ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc since it is shared with the PUNIT, but in this special case the _PS3 method is a no-op so we can safely allow a "fake" suspend / resume. Fixes: 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861 Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBusMika Westerberg2018-08-301-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR") made it possible for AML code to access SMBus I/O ports by installing custom SystemIO OpRegion handler and blocking i80i driver access upon first AML read/write to this OpRegion. However, while ThinkPad T560 does have SystemIO OpRegion declared under the SMBus device, it does not access any of the SMBus registers: Device (SMBU) { ... OperationRegion (SMBP, PCI_Config, 0x50, 0x04) Field (SMBP, DWordAcc, NoLock, Preserve) { , 5, TCOB, 11, Offset (0x04) } Name (TCBV, 0x00) Method (TCBS, 0, NotSerialized) { If ((TCBV == 0x00)) { TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05) } Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */ } OperationRegion (TCBA, SystemIO, TCBS (), 0x10) Field (TCBA, ByteAcc, NoLock, Preserve) { Offset (0x04), , 9, CPSC, 1 } } Problem with the current approach is that it blocks all I/O port access and because this system has touchpad connected to the SMBus controller after first AML access (happens during suspend/resume cycle) the touchpad fails to work anymore. Fix this so that we allow ACPI AML I/O port access if it does not touch the region reserved for the SMBus. Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737 Reported-by: Yussuf Khalil <dev@pp3345.net> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: don't use any __deprecated handling anymoreSedat Dilek2018-08-241-1/+0
| | | | | | | | | | | | This can be dropped with commit 771c035372a036f83353eef46dbb829780330234 ("deprecate the '__deprecated' attribute warnings entirely and for good") now in upstream. And we got rid of the last __deprecated use, too. Signed-off-by: Sedat Dilek <sedat.dilek@credativ.de> [wsa: shortened commit message to reflect the current situation] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: use SPDX identifier for Renesas driversWolfram Sang2018-08-245-30/+5
| | | | | | Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: ocores: update my email addressPeter Korsgaard2018-08-241-2/+2
| | | | | | | The old @sunsite.dk address is no longer active, so update the references. Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* i2c: remove deprecated attach_adapter callbackWolfram Sang2018-08-241-10/+1
| | | | | | | There aren't any users left. Remove this callback from the 2.4 times. Phew, finally, that took years to reach... Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* Merge branch 'i2c/for-4.19' of ↵Linus Torvalds2018-08-2237-593/+2572
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: - the core has now a lockless variant of i2c_smbus_xfer. Some open coded versions of this got removed in drivers. This also enables proper SCCB support in regmap. - locking got a more precise naming. i2c_{un}lock_adapter() had to go, and we know use i2c_lock_bus() consistently with flags like I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity. - the gpio fault injector got a new delicate testcase - the bus recovery procedure got fixed to handle the new testcase correctly - a new quirk flag for controllers not able to handle zero length messages together with driver updates to use it - new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl family S900 - and a good set of driver improvements and bugfixes * 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits) i2c: rcar: implement STOP and REP_START according to docs i2c: rcar: refactor private flags i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes dt-bindings: i2c: rcar: Add r8a774a1 support dt-bindings: i2c: sh_mobile: Add r8a774a1 support i2c: imx: Simplify stopped state tracking i2c: imx: Fix race condition in dma read i2c: pasemi: remove hardcoded bus numbers on smbus i2c: designware: Add SPDX license tag i2c: designware: Convert to use struct i2c_timings i2c: core: Parse SDA hold time from firmware i2c: designware-pcidrv: Mark expected switch fall-through i2c: amd8111: Mark expected switch fall-through i2c: sh_mobile: use core to detect 'no zero length read' quirk i2c: xlr: use core to detect 'no zero length' quirk i2c: rcar: use core to detect 'no zero length' quirk i2c: stu300: use core to detect 'no zero length' quirk i2c: pmcmsp: use core to detect 'no zero length' quirk i2c: mxs: use core to detect 'no zero length' quirk ...
| * i2c: rcar: implement STOP and REP_START according to docsWolfram Sang2018-08-201-14/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When doing a REP_START after a read message, the driver used to trigger a STOP first which would then be overwritten by REP_START. This was the only stable method found when doing the last refactoring. However, this was not in accordance with the documentation. After research from our BSP team and myself, we now can implement a version which works and is according to the documentation. The new approach ensures the ICMCR register is only changed when really needed. Tested on a R-Car Gen2 (H2) and Gen3 with DMA (M3N). Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: rcar: refactor private flagsWolfram Sang2018-08-201-3/+4
| | | | | | | | | | | | | | | | | | Use BIT macro to avoid shift-31-problem, indent a little more and use GENMASK to make it easier to add new flags. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return valueHans de Goede2018-08-201-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently acpi_gsb_i2c_read_bytes() directly returns i2c_transfer's return value. i2c_transfer returns a value < 0 on error and 2 (for 2 successfully executed transfers) on success. But the ACPI code expects 0 on success, so currently acpi_gsb_i2c_read_bytes()'s caller does: if (status > 0) status = 0; This commit makes acpi_gsb_i2c_read_bytes() return a value which can be directly consumed by the ACPI code, mirroring acpi_gsb_i2c_write_bytes(), this commit also makes acpi_gsb_i2c_read_bytes() explitcly check that i2c_transfer returns 2, rather then accepting any value > 0. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: core: ACPI: Properly set status byte to 0 for multi-byte writesHans de Goede2018-08-201-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | acpi_gsb_i2c_write_bytes() returns i2c_transfer()'s return value, which is the number of transfers executed on success, so 1. The ACPI code expects us to store 0 in gsb->status for success, not 1. Specifically this breaks the following code in the Thinkpad 8 DSDT: ECWR = I2CW = ECWR /* \_SB_.I2C1.BAT0.ECWR */ If ((ECST == Zero)) { ECRD = I2CR /* \_SB_.I2C1.I2CR */ } Before this commit we set ECST to 1, causing the read to never happen breaking battery monitoring on the Thinkpad 8. This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer() returns 1, so the single write transfer completed successfully, and makes it return -EIO on for other (unexpected) return values >= 0. Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: imx: Simplify stopped state trackingEsben Haabendal2018-08-201-8/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Always update the stopped state when busy status have been checked. This is identical to what was done before, with the exception of error handling. Without this change, some errors cause the stopped state to be left in incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and i2c_imx_xfer(). Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: imx: Fix race condition in dma readEsben Haabendal2018-08-201-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a race condition, where the DMAEN bit ends up being set after I2C slave has transmitted a byte following the dummy read. When that happens, an interrupt is generated instead, and no DMA request is generated to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec). Fixed by setting the DMAEN bit before the dummy read. Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
| * i2c: pasemi: remove hardcoded bus numbers on smbusDarren Stevens2018-08-201-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | The pasemi smbus controller uses PCI_FUNC(dev->devfn) to define which number bus to attach to, however this fails when something else is probed first, for example an ATI Radeon graphics card will claim 9 or 10 busses, including the ones the pasemi wants. Patch the driver to call i2c_add_adapter rather than i2c_add_numbered_adapter. Signed-off-by: Darren Stevens <darren@stevens-zone.net> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: designware: Add SPDX license tagAndy Shevchenko2018-08-207-94/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace short statement in comment with proper SPDX license tag. Note, for i2c-desingware-slave.c the identifier is chosen in accordance with MODULE_LICENSE() macro since it is visible to user. Another point to this choice is that the header seems to be copy'n'paste from the other file of this very driver. Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: designware: Convert to use struct i2c_timingsAndy Shevchenko2018-08-083-34/+33
| | | | | | | | | | | | | | | | | | | | | | | | Instead of using custom variables and parser, convert the driver to use the ones provided by I2C core. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: core: Parse SDA hold time from firmwareAndy Shevchenko2018-08-081-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | There are two drivers already using the SDA hold time setting. It might be more in the future, thus, make I2C core to parse the setting for us if provided by firmware. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: designware-pcidrv: Mark expected switch fall-throughGustavo A. R. Silva2018-08-081-0/+1
| | | | | | | | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: amd8111: Mark expected switch fall-throughGustavo A. R. Silva2018-08-081-0/+1
| | | | | | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: sh_mobile: use core to detect 'no zero length read' quirkWolfram Sang2018-08-041-5/+5
| | | | | | | | | | | | | | | | And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: xlr: use core to detect 'no zero length' quirkWolfram Sang2018-08-041-6/+5
| | | | | | | | | | | | | | And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: rcar: use core to detect 'no zero length' quirkWolfram Sang2018-08-041-7/+6
| | | | | | | | | | | | | | | | And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: stu300: use core to detect 'no zero length' quirkWolfram Sang2018-08-041-6/+6
| | | | | | | | | | | | | | | | And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: pmcmsp: use core to detect 'no zero length' quirkWolfram Sang2018-08-041-16/+1
| | | | | | | | | | | | | | And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: mxs: use core to detect 'no zero length' quirkWolfram Sang2018-08-041-3/+5
| | | | | | | | | | | | | | And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: designware-master: use core to detect 'no zero length' quirkWolfram Sang2018-08-041-7/+5
| | | | | | | | | | | | | | | | | | | | And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: quirks: add zero length checksWolfram Sang2018-08-041-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | Some adapters do not support a message length of 0. Add this as a quirk so drivers don't have to open code it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * i2c: aspeed: Add an explicit type casting for *get_clk_reg_valJae Hyun Yoo2018-08-041-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This commit fixes this sparse warning: drivers/i2c/busses/i2c-aspeed.c:875:38: warning: incorrect type in assignment (different modifiers) drivers/i2c/busses/i2c-aspeed.c:875:38: expected unsigned int ( *get_clk_reg_val )( ... ) drivers/i2c/busses/i2c-aspeed.c:875:38: got void const *const data Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * Merge branch 'i2c-mux/for-next' of https://github.com/peda-r/i2c-mux into ↵Wolfram Sang2018-08-041-13/+11
| |\ | | | | | | | | | | | | | | | i2c/for-4.19 Simplify the probe function of the pca954x driver
| | * i2c: mux: pca954x: use helper variable in probeLinus Walleij2018-07-301-13/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This creates a struct device *dev helper variable in probe() which IMO makes the code less cluttered and easier to read. Also rename the of_node veriable to the common shortform "np" (node pointer). Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [peda: slightly edited commit message and removed some surplus newlines] Signed-off-by: Peter Rosin <peda@axentia.se>
| * | i2c: Add Actions Semiconductor Owl family S900 I2C driverManivannan Sadhasivam2018-08-043-0/+503
| | | | | | | | | | | | | | | | | | | | | | | | Add Actions Semiconductor Owl family S900 I2C driver. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controllerKarthikeyan Ramasubramanian2018-07-313-0/+687
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This bus driver supports the GENI based i2c hardware controller in the Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable module supporting a wide range of serial interfaces including I2C. The driver supports FIFO mode and DMA mode of transfer and switches modes dynamically depending on the size of the transfer. Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org> Signed-off-by: Sagar Dharia <sdharia@codeaurora.org> Signed-off-by: Girish Mahadevan <girishm@codeaurora.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Stephen Boyd <swboyd@chromium.org> [wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: rcar: handle RXDMA HW behaviour on Gen3Wolfram Sang2018-07-231-3/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Gen3, we can only do RXDMA once per transfer reliably. For that, we must reset the device, then we can have RXDMA once. This patch implements this. When there is no reset controller or the reset fails, RXDMA will be blocked completely. Otherwise, it will be disabled after the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu Yamasaki, yet completely refactored to handle multiple read messages within one transfer. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: aspeed: Adjust spinlock scope in the irq handlerJae Hyun Yoo2018-07-211-6/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adjusts spinlock scope to make it wrap the whole irq handler using a single lock/unlock which covers both master and slave handlers. Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: aspeed: Fix initial values of master and slave stateJae Hyun Yoo2018-07-211-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch changes the order of enum aspeed_i2c_master_state and enum aspeed_i2c_slave_state defines to make their initial value to ASPEED_I2C_MASTER_INACTIVE and ASPEED_I2C_SLAVE_STOP respectively. In case of multi-master use, if a slave data comes ahead of the first master xfer, master_state starts from an invalid state so this change fixes the issue. Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: aspeed: Add newline characters into message printings.Jae Hyun Yoo2018-07-211-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | There are some log printing without a newline character. This patch adds the missing newline characters. Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: exynos5: Describe the hardware variant for readabilityKrzysztof Kozlowski2018-07-211-8/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver supports multiple hardware variants of Exynos I2C controller which differ in FIFO depth, handling of interrupts and bus recovery in HSI2C_MASTER_ST_LOSE state. The difference in variant was a single bit set for Exynos7 variants and implicit lack of this bit for other variants. Make each variant explicit which also fixes the GCC warning about documentation: drivers/i2c/busses/i2c-exynos5.c:223: warning: Function parameter or member 'hw' not described in 'exynos_hsi2c_variant' No change in functionality. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: recovery: make pin init look like STOPWolfram Sang2018-07-211-9/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we initialize the pins, make sure it looks like STOP by dividing the delay into halves. It shouldn't matter because SDA is expected to be held low by a device, but for super-safety, let's do it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Reviewed-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: fsi: Add bus recoveryEddie James2018-07-211-0/+132
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bus recovery should reset the bus with the standard i2c recovery procedure. Populate the necessary fields so that the standard procedure can perform the reset. Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com> Tested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: fsi: Add I2C master lockingEddie James2018-07-211-4/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since there are many ports per master, each with it's own adapter and chardev, we need some locking to prevent transfers from changing the master state while other transfers are in progress. Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| * | i2c: fsi: Add transfer implementationEddie James2018-07-211-2/+193
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Execute I2C transfers from the FSI-attached I2C master. Use polling instead of interrupts as we have no hardware IRQ over FSI. Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>