summaryrefslogtreecommitdiffstats
path: root/drivers/iio (follow)
Commit message (Collapse)AuthorAgeFilesLines
* iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machinesHans de Goede2018-06-241-0/+2
| | | | | | | | | | | | | | | | | | | | Commit 5ec6486daa98 ("iio:imu: inv_mpu6050: support more interrupt types") causes inv_mpu_core_probe() to fail if the IRQ does not have a trigger-type setup. This happens on machines where the mpu6050 is enumerated through ACPI and an older Interrupt type ACPI resource is used for the interrupt, rather then a GpioInt type type, causing the mpu6050 driver to no longer work there. This happens on e.g. the Asus T100TA. This commits makes the mpu6050 fallback to the old IRQF_TRIGGER_RISING default if the irq-type is not setup, fixing this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Fixes: 5ec6486daa98 ("iio:imu: inv_mpu6050: support more interrupt types") Reviewed-by: Martin Kelly <mkelly@xevo.com> Reviewed-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* iio: mma8452: Fix ignoring MMA8452_INT_DRDYLeonard Crestez2018-06-241-1/+1
| | | | | | | | | | | | | | | | Interrupts are ignored if no event bit is set in the status status register and this breaks the buffer interface. No data is shown when running "iio_generic_buffer -n mma8451 -a" and interrupt counts go crazy. Fix by not returning IRQ_NONE if DRDY is set. Fixes: 605f72de137a ("iio: accel: mma8452: improvements to handle multiple events") Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* iio: tsl2x7x/tsl2772: avoid potential division by zeroColin Ian King2018-06-241-0/+2
| | | | | | | | | | | | It may be possible for tsl2772_get_lux to return a zero lux value and hence a division by zero can occur when lux_val is zero. Check for this case and return -ERANGE to avoid the division by zero. Detected by CoverityScan, CID#1469484 ("Division or modulo by zero") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* iio: pressure: bmp280: fix relative humidity unitTomasz Duszynski2018-06-241-3/+2
| | | | | | | | | | | | | | | | According to IIO ABI relative humidity reading should be returned in milli percent. This patch addresses that by applying proper scaling and returning integer instead of fractional format type specifier. Note that the fixes tag is before the driver was heavily refactored to introduce spi support, so the patch won't apply that far back. Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com> Fixes: 14beaa8f5ab1 ("iio: pressure: bmp280: add humidity support") Acked-by: Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* treewide: devm_kzalloc() -> devm_kcalloc()Kees Cook2018-06-135-13/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* treewide: devm_kmalloc() -> devm_kmalloc_array()Kees Cook2018-06-131-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The devm_kmalloc() function has a 2-factor argument form, devm_kmalloc_array(). This patch replaces cases of: devm_kmalloc(handle, a * b, gfp) with: devm_kmalloc_array(handle, a * b, gfp) as well as handling cases of: devm_kmalloc(handle, a * b * c, gfp) with: devm_kmalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kmalloc_array(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kmalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kmalloc..." instead of "= devm_kmalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kmalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kmalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kmalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kmalloc + devm_kmalloc_array (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kmalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kmalloc(HANDLE, C1 * C2 * C3, ...) | devm_kmalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kmalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kmalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kmalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kmalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kmalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kmalloc(HANDLE, C1 * C2 * C3, ...) | devm_kmalloc(HANDLE, C1 * C2, ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* treewide: kzalloc() -> kcalloc()Kees Cook2018-06-132-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* Merge tag 'staging-4.18-rc1' of ↵Linus Torvalds2018-06-0961-878/+5141
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging/IIO updates from Greg KH: "Here is the big staging and IIO driver update for 4.18-rc1. It was delayed as I wanted to make sure the final driver deletions did not cause any major merge issues, and all now looks good. There are a lot of patches here, just over 1000. The diffstat summary shows the major changes here: 1007 files changed, 16828 insertions(+), 227770 deletions(-) Because of this, we might be close to shrinking the overall kernel source code size for two releases in a row. There was loads of work in this release cycle, primarily: - tons of ks7010 driver cleanups - lots of mt7621 driver fixes and cleanups - most driver cleanups - wilc1000 fixes and cleanups - lots and lots of IIO driver cleanups and new additions - debugfs cleanups for all staging drivers - lots of other staging driver cleanups and fixes, the shortlog has the full details. but the big user-visable things here are the removal of 3 chunks of code: - ncpfs and ipx were removed on schedule, no one has cared about this code since it moved to staging last year, and if it needs to come back, it can be reverted. - lustre file system is removed. I've ranted at the lustre developers about once a year for the past 5 years, with no real forward progress at all to clean things up and get the code into the "real" part of the kernel. Given that the lustre developers continue to work on an external tree and try to port those changes to the in-kernel tree every once in a while, this whole thing really really is not working out at all. So I'm deleting it so that the developers can spend the time working in their out-of-tree location and get things cleaned up properly to get merged into the tree correctly at a later date. Because of these file removals, you will have merge issues on some of these files (2 in the ipx code, 1 in the ncpfs code, and 1 in the atomisp driver). Just delete those files, it's a simple merge :) All of this has been in linux-next for a while with no reported problems" * tag 'staging-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1011 commits) staging: ipx: delete it from the tree ncpfs: remove uapi .h files ncpfs: remove Documentation ncpfs: remove compat functionality staging: ncpfs: delete it staging: lustre: delete the filesystem from the tree. staging: vc04_services: no need to save the log debufs dentries staging: vc04_services: vchiq_debugfs_log_entry can be a void * staging: vc04_services: remove struct vchiq_debugfs_info staging: vc04_services: move client dbg directory into static variable staging: vc04_services: remove odd vchiq_debugfs_top() wrapper staging: vc04_services: no need to check debugfs return values staging: mt7621-gpio: reorder includes alphabetically staging: mt7621-gpio: change gc_map to don't use pointers staging: mt7621-gpio: use GPIOF_DIR_OUT and GPIOF_DIR_IN macros instead of custom values staging: mt7621-gpio: change 'to_mediatek_gpio' to make just a one line return staging: mt7621-gpio: dt-bindings: update documentation for #interrupt-cells property staging: mt7621-gpio: update #interrupt-cells for the gpio node staging: mt7621-gpio: dt-bindings: complete documentation for the gpio staging: mt7621-dts: add missing properties to gpio node ...
| * iio: imu: inv_mpu6050: add comment about frequenciesMartin Kelly2018-05-221-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | Although the driver allows frequencies between 4 and 1000 Hz, only the frequencies advertised in the available frequencies file are backed properly by a low-pass filter to prevent aliasing, so it's best to use them. Since this is not obvious to the user, add a comment explaining what's going on. Signed-off-by: Martin Kelly <mkelly@xevo.com> Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: dac: Add support for external reference voltage through the regulator ↵Silvan Murer2018-05-221-9/+61
| | | | | | | | | | | | | | | | framework. Signed-off-by: Silvan Murer <silvan.murer@gmail.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: dac: fix missing of_match_table assignment in the LTC 2632 deviceSilvan Murer2018-05-221-9/+10
| | | | | | | | | | | | Signed-off-by: Silvan Murer <silvan.murer@gmail.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: adc: fix spelling mistake: "Freeacale" -> "Freescale"Colin Ian King2018-05-221-1/+1
| | | | | | | | | | | | | | Trivial fix to spelling mistake in module description text Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: amplifiers: ad8366: move channel init before iio_device_register()Alexandru Ardelean2018-05-221-2/+4
| | | | | | | | | | | | | | | | Otherwise a race condition can occur, where userspace can start operations before the channels have been properly initialized. Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * staging: iio: ad2s1200: Move driver out of stagingDavid Veenstra2018-05-205-0/+234
| | | | | | | | | | | | | | | | Move the iio driver for the ad2s1200 and ad2s1205 resolver-to-digital converter out of staging, into mainline iio subsystems. Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio:dac:ad5686: Add AD5681R/AD5682R/AD5683/AD5683R supportStefan Popa2018-05-203-8/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AD5681R/AD5682R/AD5683/AD5683R are a family of one channel DACs with 12-bit, 14-bit and 16-bit precision respectively. The devices have either no built-in reference, or built-in 2.5V reference. These devices are similar to AD5691R/AD5692R/AD5693/AD5693R except with a few notable differences: * they use the SPI interface instead of I2C * in the write control register, DB18 and DB17 are used for setting the power mode, while DB16 is the REF bit. This is why a new regmap type was defined and checked accordingly. * the shift register is 24 bits wide, the first four bits are the command bits followed by the data bits. As the data comprises of 20-bit, 18-bit or 16-bit input code, this means that 4 LSB bits are don't care. This is why the data needs to be shifted on the left with four bits. Therefore, AD5683_REGMAP is checked inside a switch case in the ad5686_spi_write() function. On the other hand, similar devices such as AD5693R family, have the 4 MSB command bits followed by 4 don't care bits. Datasheet: http://www.analog.com/media/en/technical-documentation/data-sheets/AD5683R_5682R_5681R_5683.pdf Signed-off-by: Stefan Popa <stefan.popa@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio:dac:ad5686: Add AD5691R/AD5692R/AD5693/AD5693R supportStefan Popa2018-05-203-7/+109
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AD5691R/AD5692R/AD5693/AD5693R are a family of one channel DACs with 12-bit, 14-bit and 16-bit precision respectively. The devices have either no built-in reference, or built-in 2.5V reference. These devices are pretty similar to AD5671R/AD5675R and AD5694/AD5694R/AD5695R/AD5696/AD5696R, except that they have one channel. Another difference is that they use a write control register(addr 0x04) for setting the power down modes and the internal reference instead of separate registers for each function. Datasheet: http://www.analog.com/media/en/technical-documentation/data-sheets/AD5693R_5692R_5691R_5693.pdf Signed-off-by: Stefan Popa <stefan.popa@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: adc: stm32-dfsdm: include stm32-dfsdm-adc.hFabrice Gasnier2018-05-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | Fix the following sparse warnings: CHECK drivers/iio/adc/stm32-dfsdm-adc.c symbol 'stm32_dfsdm_get_buff_cb' was not declared. Should it be static? symbol 'stm32_dfsdm_release_buff_cb' was not declared. Should it be static? BTW, move interrupt.h to sort headers alphabetically. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: tsl2583: correct values in integration_time_availableBrian Masney2018-05-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The times reported by the in_illuminance_integration_time_available sysfs attribute are actually in milliseconds, not microseconds. This patch corrects the times with the correct unit. The fixes tag is inaccurate as the issue existed when the driver was still in staging. However, lots of changes occured before it graduated so this is as a good a point as any for backports. Signed-off-by: Brian Masney <masneyb@onstation.org> Fixes: f44d5c8ac399 ("staging: iio: tsl2583: move out of staging") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * staging: iio: tsl2x7x/tsl2772: move out of stagingBrian Masney2018-05-123-0/+1809
| | | | | | | | | | | | | | Move the tsl2772 driver out of staging and into mainline. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: accell: mma8452: Reduce sleep time when data not readyRichard Tresidder2018-05-121-1/+23
| | | | | | | | | | | | | | Modified the sleep method when data is not ready to allow for sampling > 50sps to work. Signed-off-by: Richard Tresidder <rtresidd@electromag.com.au> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: adc: ti-ads8688: add trigger and buffer supportSean Nyekjaer2018-05-121-3/+45
| | | | | | | | | | Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: potentiostat: lmp91000: add LMP91002 supportMatt Ranostay2018-05-121-0/+2
| | | | | | | | | | | | | | | | LMP91002 is register compatible so add devicetree and i2c client ids Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: magnetometer: mag3110: Add ability to run in continuous modeRichard Tresidder2018-05-121-18/+140
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds the ability to run the Mag3110 in continuous mode to speed up the sampling rate. Depending on the sampling rate requested the device can be put in or out of continuous mode automatically. Shifting out of continuous mode requires a potential 1 / ODR wait which is also implemented. Modified the sleep method when data is not ready to allow for sampling > 50sps to work. Signed-off-by: Richard Tresidder <rtresidd@electromag.com.au> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: adc: stm32-dfsdm: Add support for stm32mp1Fabrice Gasnier2018-05-121-0/+21
| | | | | | | | | | | | | | | | | | | | Add support for DFSDM (Digital Filter For Sigma Delta Modulators) to STM32MP1. This variant is close to STM32H7 DFSDM, it implements 6 filter instances. Registers map is also increased. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: imu: inv_mpu6050: make loop a do-whileMartin Kelly2018-05-121-2/+2
| | | | | | | | | | | | | | | | | | | | Prior to this loop, we check if fifo_count < bytes_per_datum and bail if so. This means that when we hit the loop, we know that fifo_count >= bytes_per_datum, so the check is unneeded and we can turn the loop into a do-while for a slight performance improvement. Signed-off-by: Martin Kelly <mkelly@xevo.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * Merge tag 'iio-for-4.18a' of ↵Greg Kroah-Hartman2018-05-1147-827/+2608
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: 1st round of IIO new device support, features and cleanup for the 4.18 cycle A nice mix this time of excellent cleanups (many to send drivers speeding toward staging graduations) and new drivers / device support. A good part of this is Brian Masney's never ending task on the tsl2x7x driver. The end is in sight so hopefully we'll get that one out of staging very soon! New device support * AD5686 - Support AD5685R (was wrongly present as AD5685) - Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel SPI DACs with various precisions. - Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R I2C DACs with various percisions and numbers of channels. * Analog front end rescale driver - New driver. - Support current sensing usings a shunt resistor. - Support simple voltage dividers. - support simple current sense amplifiers. * TI dac5571 - New driver and device bindings supporting: dac5571, dac6571, dac7571, dac5574, dac6574, dac7574, dac5573, dac6573 and dac7573 * Meson-adc - Support for Meson AXG with DT bindings. * mpu6050 - Support the mpu9255 which only requires additional WHOAMI entry and compatible string. * st_lsm6dsx - Support for lsm330dlc combinded accelerometer and gyro sensors with DT bindings. * stm32_adc - Add support for STM32MP1 with bindings. Staging graduations * adis16201 after some excelent cleanup by Himanshu Jha. * adis16029 after some excelent cleanup by Shreeya Patel. New features: * ABI docs - Add core ABI docs for angle channels. * inv_mpu6050 - Provide support for the full range of interrupts the device supports. * st_accel - Add SMO8840 ACPI ID seen in the wild on some Lenovo machines. * stx104 - Provide a multiple gpio get function. Cleanups / Minor fixes * core - Use new nested structure support to improve kernel-doc. * ad2s1200 - Use be16_to_cpup instead of opencoding. * ad5686 - Indentation tidy up. - Switch to SPDX - Refactor to allow various numbers of channels. - Refactor to separate core and SPI specific support, prior to addition of i2c equivalent devices. * ad7606 - Use drvdata directly from device rather than boucing via the platform_device structure. * ad7746 - Replace opencoded byte swapped i2c calls with _swapped variants. - White space and line break readability improvements. - Reorder includes and variable declarations where appropriate. * ad7791 - Changes to the AD ADC library used by this driver took in the sampling frequency. This lead to be the wrong path being the one tied to the resulting attribute, so it didn't work, and a warning to be printed. * ad7780 - Remove apparent support for sampling frequency control on devices that don't support changing the sampling attributes. * ade7854 - Fix a read of the wrong number of bits. - Improve error handling on i2c read/write errors. - Rework i2c and spi code to reduce duplication. * adis16201 (staging) - Improve meaning inherent in some macro names by adding units etc where relevant. - Adjust comments to improve detail and drop the irrelevant. - Rename register address definitions definitions to add a _REG postfix, clearly separating them from field definitions. Reorganize the definitions to group register address and fields. - Use sign_extend32 rather than open coding. - Reverse Xmas tree ordering where appropriate and align function args. - Remove unused headers. - Use GENMASK where appropriate instead of open coding. * adis16209 (staging) - Indent field definitions to visually separate them from register address definitions. - Use reverse xmas tree ordering where appropriate. - Add some whitespace where it will help readability. - Drop some unused headers. - Use GENMASK where appropriate. * ad2s1200 - Drop unnecessary includes and reorder alphabetically. - Reverse xmas tree and blank line cleanups. * atlas-ph-sensor - Use msleep instead of usleep_range where the precise value doesn't matter and the delays are long. * bcm150 - Drop transaction splitting as core now handles it. * cros_ec - Move the shared header to the include/iio/common directory. This brings it inline with the other multiple type devices. - Use drvdata directly from device rather than boucing via the platform_device structure. * hid-sensors - Use drvdata directly from device rather than boucing via the platform_device structure. * inv_mpu6050 - Clear out a second function definition for the same function. - Don't flush fifo when the iio buffer is full but just drop excess data. - Tidy up set_power_itg and ensure it is used in the right places. - Use set_power_itg rather than opencoding it again in the i2c mux control. - Make sure error paths disable the power if undoing power on. - Used managed devm_ functions during probe. Delete remove function. - Refactor to pull raw data read out of read_raw function. - Simplify data reading error paths. - Only enable the i2c mux for chips with the i2c aux bus (not icm20608) - Fix a potential deadlock due to varying lock ordering. - Fix an issue where first sample from gyro after enabling is unstable by dropping the first sample. - Fix an issue where the user_ctrl register is incorrectly overwritten. - Tidy up some grammar and spelling minor issus. * mcp320x - Use vendor compatible strings. * mcp4018 - Switch to using i2c .probe_new. * mcp4351 - switch to using i2c .probe_new. * meson-adc - rework handing on common ADC platform data so it can be shared across multiple families of SoCs. * sca3000 - Fix an error handling path if the ring configure fails. * st_lsm6dsx - Fix a wrong fifo threshold mask (no actual effect) * stm32-dfsdm - Style fixes and cleanups. - Check filter ID is in range and check spi-max-frequency. * tsl2x7x (staging) - Drop some unnecessary function calls, unused variables and unnecessary local variables. - Fix wrong interrupt type. - Avoid unnecessary double clear of interrupt. - Simplify proximity calibration call which did various things unrelated to actually calibrating. - Separate control of the proximity and ALS interrupts. - Improve consistency of logging. - Separate ALS and proximity persistence settings as they have separate hardware controls. - Tidy up variable ordering. - Add Brian to copyright notice given consider work on this driver. - Take advantage of hardware support for I2C address auto increment. - Combine individuaal enable and period attributes for the two directions on the threshold events into a single value as the hardware doesn't separate them. - Move integration_time* attributes from light channel to intensity value as they effect the intensity readings directly and the light reading only indirectly. Hence this better reflects reality. Also move the calibscale_available. - Avoid returning an error in the IRQ handler. - Hard code the reg value in _clear_interrupts as it only takes one value in the code. Result is the function has little purpose so opencode the two remaining i2c_smbus_write_byte calls. - Drop some unnecessary checking of the chip status register. - Tidy up return path in _write_interrupt_config. - Tidy up the ID verification code. - Move the power and diode settings defines into the header as these are needed for platform data configuration. - Various renames and comment cleanups for consistency and clarity. - Use actual device defaults for default startup settings. - SPDX - Add some range sanity checking to sysfs attribute writes. - Don't provide event interfaces if the interrupt line isn't available. - Use IIO_CONST_ATTR macro for calibscale_available as it's a constant string. - Fix the integration time and lux equations. - Make device IDs explicit index values in the device_channel_config array.
| | * iio: adc: stm32-adc: add support for STM32MP1Fabrice Gasnier2018-05-072-22/+91
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for STM32MP1 ADC. It's quite similar to STM32H7 ADC. Introduce new compatible to handle variants of this hardware such as vregready flag, trigger list, interrupts, clock rate. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: dac: add TI DAC5571 family supportSean Nyekjaer2018-05-063-0/+450
| | | | | | | | | | | | | | | | | | | | | This patch adds support for the Texas Intruments DAC5571 Family. Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: minor wording fixesMartin Kelly2018-05-063-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | Just some minor grammar/spelling fixes of things I noticed while reading the code. Signed-off-by: Martin Kelly <mkelly@xevo.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: fix user_ctrl register overwrittenJean-Baptiste Maneyrol2018-05-065-12/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When in spi mode, we are setting i2c disable bit in user_ctrl register. But the register is overwritten after when turning fifo on. So save user_ctrl init value and always use it when updating the register. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: skip first sample when gyro is onJean-Baptiste Maneyrol2018-05-063-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement generic skip first samples mechanism and use it to filter out first sample when gyro is on. The problem for these chips is that the first sample of the gyro is out of specs, because gyro is not completely stabilized. To ensure all data are within sensor specs, we just skip the first sample when turning gyro on. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: fix possible deadlock between mutex and iioJean-Baptiste Maneyrol2018-05-061-18/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Detected by kernel circular locking dependency checker. We are locking iio mutex (iio_device_claim_direct_mode) after locking our internal mutex. But when the buffer starts, iio first locks its mutex and then we lock our internal one. To avoid possible deadlock, we need to use the same order everwhere. So we change the ordering by locking first iio mutex, then our internal mutex. Fixes: 68cd6e5b206b ("iio: imu: inv_mpu6050: fix lock issues by using our own mutex") Cc: stable@vger.kernel.org Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: use i2c mux only for chip with i2c aux busJean-Baptiste Maneyrol2018-05-061-16/+25
| | | | | | | | | | | | | | | | | | | | | | | | icm20608 does not have i2c aux bus, so it does not make sense to allocate an i2c mux for this chip. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: afe: rescale: new driverPeter Rosin2018-04-285-0/+386
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If an ADC channel measures the midpoint of a voltage divider, the interesting voltage is often the voltage over the full resistance. E.g. if the full voltage is too big for the ADC to handle. Likewise, if an ADC channel measures the voltage across a shunt resistor, with or without amplification, the interesting value is often the current through the resistor. This driver solves these problems by allowing to linearly scale a channel and/or by allowing changes to the type of the channel. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: accel: bcm150: Remove handling for regmap raw_read_maxCharles Keepax2018-04-281-20/+3
| | | | | | | | | | | | | | | | | | | | | | | | The regmap core now handles splitting up transactions according to max_raw_read, so this code is no longer required in client drivers. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: clean read channel data error pathJean-Baptiste Maneyrol2018-04-281-6/+10
| | | | | | | | | | | | | | | | | | | | | | | | Delete the useless ored result and give a second chance to turn the chip back off at the end. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: clean read raw by factorizing out raw dataJean-Baptiste Maneyrol2018-04-281-54/+62
| | | | | | | | | | | | | | | | | | | | | Factorize reading channel data in its own function. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: use devm_* at init and delete removeJean-Baptiste Maneyrol2018-04-285-47/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | Use devm_* for iio_triggered_buffer_setup, iio_device_register, iio_trigger_register. Delete unneeded inv_mpu6050_remove_trigger, inv_mpu_core_remove, and inv_mpu_remove for spi driver. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: fix error path not turning chip back offJean-Baptiste Maneyrol2018-04-282-16/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | Some functions are turning the chip on and not back off in error path. With set_power function using a reference counter that would keep the chip on forever. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: adc: stm32-dfsdm: add check on spi-max-frequencyFabrice Gasnier2018-04-281-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | spi-max-frequency is requested for SPI master mode (only), to tune output clock. It may happen requested frequency isn't reachable. Add explicit check, so probe fails with error in this case. Otherwise, output clock may simply be silently turned off (conversions fail). Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: adc: stm32-dfsdm: add check on max filter idFabrice Gasnier2018-04-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | reg property should be checked against number of available filters. BTW, dfsdm->num_fls wasn't used. But it can be used for this purpose. This prevents using data out of allocated dfsdm->fl_list array. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: adc: stm32-dfsdm: misc style improvements and fixesFabrice Gasnier2018-04-281-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Misc fixes & style improvements: - checkpatch warns about line over 80 characters. - remove extra spaces and a blank line (e.g. checkpatch --strict) - remove bad error message always printed in probe routine. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: common: hid-sensors: simplify getting .drvdataWolfram Sang2018-04-281-6/+3
| | | | | | | | | | | | | | | | | | | | | | | | We should get drvdata from struct device directly. Going via platform_device is an unneeded step back and forth. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: common: cros_ec_sensors: simplify getting .drvdataWolfram Sang2018-04-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | We should get drvdata from struct device directly. Going via platform_device is an unneeded step back and forth. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: accel: st_accel: Add support for the SMO8840 ACPI idHans de Goede2018-04-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | The Lenovo Ideapad Miix 320 uses an st accelerometer with an ACPI id of SMO8840, add support for this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio:imu: inv_mpu6050: support more interrupt typesMartin Kelly2018-04-215-8/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, we support only rising edge interrupts, and in fact we assume that the interrupt we're given is rising edge (and things won't work if it's not). However, the device supports rising edge, falling edge, level low, and level high interrupts. Empirically, on my system, switching to level interrupts has fixed a problem I had with significant (~40%) interrupt loss with edge interrupts. This issue is likely related to the SoC I'm using (Allwinner H3), but being able to switch the interrupt type is still a very useful workaround. I tested this with each interrupt type and verified correct behavior in a logic analyzer. Add support for these interrupt types while also eliminating the error case of the device tree and driver using different interrupt types. Signed-off-by: Martin Kelly <mkelly@xevo.com> Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: use set_power_itg function in i2c muxJean-Baptiste Maneyrol2018-04-211-20/+13
| | | | | | | | | | | | | | | | | | | | | | | | Set power function is rewritten manually inside i2c mux select. Better use the already identical existing function. Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: imu: inv_mpu6050: clean set_power_itg and fix usageJean-Baptiste Maneyrol2018-04-211-20/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rewrite set_power_itg. Failing when turning power off is no more decreasing the counter now and sleeping only happens when effectively turning the chip on. Fix also usage in init function (setting power on one time is sufficient to ensure chip is effectively on). Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: sca3000: Handle errors returned by 'sca3000_configure_ring()' in ↵Christophe JAILLET2018-04-151-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 'sca3000_probe()' 'sca3000_configure_ring()' can fail, so test its return value and propagate it if needed. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * iio: sca3000: Fix an error handling path in 'sca3000_probe()'Christophe JAILLET2018-04-151-8/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use 'devm_iio_kfifo_allocate()' instead of 'iio_kfifo_allocate()' in order to simplify code and avoid a memory leak in an error path in 'sca3000_probe()'. A call to 'sca3000_unconfigure_ring()' was missing. Sent via the next merge window as unimportant bug and there are other patches dependent on it. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-21 10:48:29 +0100