| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
| |
The SoC camera framework has no functional drivers left, something that
has not changed for years. Move the leftovers to the staging tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs
can capture and compress video data from digital or analog sources. With
the Aspeed chip acting a service processor, the Video Engine can capture
the host processor graphics output.
Add a V4L2 driver to capture video data and compress it to JPEG images.
Make the video frames available through the V4L2 streaming interface.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Allwinner V3s SoC features a CSI module with parallel interface.
This patch implement a v4l2 framework driver for it.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Yong Deng <yong.deng@magewell.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support to the CEC device implemented with a STM32
microcontroller in X86 SECO Boards, including UDOO X86.
The communication is achieved via Braswell integrated SMBus
(i2c-i801). The driver use direct access to the PCI addresses, due to
the limitations of the specific driver in presence of ACPI calls.
The basic functionalities are tested with success with cec-ctl and
cec-compliance.
Inspired by cros-ec-cec implementation, attaches to i915 driver
cec-notifier.
Signed-off-by: Ettore Chimenti <ek5.chimenti@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add a V4L2 mem-to-mem scaler/CSC driver for the Pixel Pipeline (PXP)
version found on i.MX6ULL SoCs. A similar variant is used on i.MX7D.
Since this driver only uses the legacy pipeline, it should be reasonably
easy to extend it to work with the older PXP versions found on i.MX6UL,
i.MX6SX, i.MX6SL, i.MX28, and i.MX23.
The driver supports scaling and colorspace conversion. There is
currently no support for rotation, alpha-blending, and the LUTs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The ChromeOS Embedded Controller can expose a CEC bus, this patch add the
driver for such feature of the Embedded Controller.
This driver is part of the cros-ec MFD and will be add as a sub-device when
the feature bit is exposed by the EC.
The controller will only handle a single logical address and handles
all the messages retries and will only expose Success or Error.
The controller will be tied to the HDMI CEC notifier by using the platform
DMI Data and the i915 device name and connector name.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Support for camera subsystem on QComm MSM8996/APQ8096 is to be added
so remove hardware version from CAMSS driver's path.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|/
|
|
|
|
|
|
|
|
|
| |
Add the virtual codec driver that uses the Fast Walsh Hadamard Transform.
Keiichi Watanabe contributed the multiplanar support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Co-Developed-by: Keiichi Watanabe <keiichiw@chromium.org>
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Cadence CSI-2 RX Controller is an hardware block meant to be used as a
bridge between a CSI-2 bus and pixel grabbers.
It supports operating with internal or external D-PHY, with up to 4 lanes,
or without any D-PHY. The current code only supports the latter case.
It also support dynamic mapping of the CSI-2 virtual channels to the
associated pixel grabbers, but that isn't allowed at the moment either.
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CEC pin injection code for testing purposes
- DVB frontend cxd2099 promoted from staging
- new platform driver for Sony cxd2880 DVB devices
- new sensor drivers: mt9t112, ov2685, ov5695, ov772x, tda1997x,
tw9910.c
- removal of unused cx18 and ivtv alsa mixers
- the reneseas-ceu driver doesn't depend on soc_camera anymore and
moved from staging
- removed the mantis_vp3028 driver, unused since 2009
- s5p-mfc: add support for version 10 of the MSP
- added a decoder for imon protocol
- atomisp: lots of cleanups
- imx074 and mt9t031: don't depend on soc_camera anymore, being
promoted from staging
- added helper functions to better support DVB I2C binding
- lots of driver improvements and cleanups
* tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (438 commits)
media: v4l2-ioctl: rename a temp var that stores _IOC_SIZE(cmd)
media: fimc-capture: get rid of two warnings
media: dvb-usb-v2: fix a missing dependency of I2C_MUX
media: uvc: to the right check at uvc_ioctl_enum_framesizes()
media: cec-core: fix a bug at cec_error_inj_write()
media: tda9840: cleanup a warning
media: tm6000: avoid casting just to print pointer address
media: em28xx-input: improve error handling code
media: zr364xx: avoid casting just to print pointer address
media: vivid-radio-rx: add a cast to avoid a warning
media: saa7134-alsa: don't use casts to print a buffer address
media: solo6x10: get rid of an address space warning
media: zoran: don't cast pointers to print them
media: ir-kbd-i2c: change the if logic to avoid a warning
media: ir-kbd-i2c: improve error handling code
media: saa7134-input: improve error handling
media: s2255drv: fix a casting warning
media: ivtvfb: Cleanup some warnings
media: videobuf-dma-sg: Fix a weird cast
soc_camera: fix a weird cast on printk
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add driver for Renesas Capture Engine Unit (CEU).
The CEU interface supports capturing 'data' (YUV422) and 'images'
(NV[12|21|16|61]).
This driver aims to replace the soc_camera-based sh_mobile_ceu one.
Tested with ov7670 camera sensor, providing YUYV_2X8 data on Renesas RZ
platform GR-Peach.
Tested with ov7725 camera sensor on SH4 platform Migo-R.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: added two 'fall-through' comments]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
| |
| |
| |
| |
| |
| |
| | |
The m32r architecture is getting removed, so this one is no longer needed.
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|/
|
|
|
|
|
|
|
| |
The blackfin architecture is getting removed, so the video
capture driver is also obsolete.
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
|
|
|
| |
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
| |
Most of the I2C headers got moved a long time ago to
include/media/i2c. Stop including them at the patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This driver adds support for the Tegra CEC IP. It is based on the
NVIDIA drivers/misc/tegra-cec driver in their 3.10 kernel.
This has been converted to the CEC framework and cleaned up.
Tested with my Jetson TK1 board. It has also been tested with the
Tegra X1 in an embedded product.
Note of warning for the Tegra X2: this SoC supports two HDMI outputs,
but only one CEC adapter and the CEC bus is shared between the
two outputs. This is a design mistake and the CEC adapter can
control only one HDMI output. Never hook up both HDMI outputs
to the CEC bus in a hardware design: this is illegal as per the
CEC specification.
The CEC bus can be shared between multiple inputs and zero or one
outputs, but not between multiple outputs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Rockchip RGA is a separate 2D raster graphic acceleration unit. It
accelerates 2D graphics operations, such as point/line drawing, image
scaling, rotation, BitBLT, alpha blending and image blur/sharpness
The driver supports various operations from the rendering pipeline.
- copy
- fast solid color fill
- rotation
- flip
- alpha blending
The code in rga-hw.c is used to configure regs according to operations
The code in rga-buf.c is used to create private mmu table for RGA.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add a simple HDMI CEC GPIO driver that sits on top of the cec-pin framework.
While I have heard of SoCs that use the GPIO pin for CEC (apparently an
early RockChip SoC used that), the main use-case of this driver is to
function as a debugging tool.
By connecting the CEC line to a GPIO pin on a Raspberry Pi 3 for example
it turns it into a CEC debugger and protocol analyzer.
With 'cec-ctl --monitor-pin' the CEC traffic can be analyzed.
But of course it can also be used with any hardware project where the
HDMI CEC line is hooked up to a pull-up gpio line.
In addition this has (optional) support for tracing HPD changes if the
HPD is connected to a GPIO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
|
|
|
|
|
| |
Add Makefile and update platform/Kconfig and platform/Makefile
to enable building of the QCom CAMSS driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Amlogic SoC embeds a standalone CEC controller, this patch adds a driver
for such controller.
The controller does not need HPD to be active, and could support up to max
5 logical addresses, but only 1 is handled since the Suspend firmware can
make use of this unique logical address to wake up the device.
The Suspend firmware configuration will be added in an other patchset.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com:s/if (ret)/if (res)/ to fix obvious typo]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds Venus driver Makefile and changes v4l2 platform
Makefile/Kconfig in order to enable building of the driver.
Note that in this initial version the COMPILE_TEST-ing is not
supported because the drivers specific to ARM builds are still
in process of enabling the aforementioned compile testing.
Once that disadvantage is fixed the Venus driver compile testing
will be possible with follow-up changes.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This driver can handle SoC internal and external video bus multiplexers,
controlled by mux controllers provided by the mux controller framework,
such as MMIO register bitfields or GPIOs. The subdevice passes through
the mbus configuration of the active input to the output side.
Since the mux framework is not yet merged, this driver contains
temporary mmio-mux support to work without the framework. The driver
should be converted to use the multiplexer API once the "mux: minimal
mux subsystem" and "mux: mmio-based syscon mux controller" patches are
merged.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[hans.verkuil@cisco.com: add 'select REGMAP' to Kconfig]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds Digital Radio Interface (DRIF) support to R-Car Gen3 SoCs.
The driver exposes each instance of DRIF as a V4L2 SDR device. A DRIF
device represents a channel and each channel can have one or two
sub-channels respectively depending on the target board.
DRIF supports only Rx functionality. It receives samples from a RF
frontend tuner chip it is interfaced with. The combination of DRIF and the
tuner device, which is registered as a sub-device, determines the receive
sample rate and format.
In order to be compliant as a V4L2 SDR device, DRIF needs to bind with
the tuner device, which can be provided by a third party vendor. DRIF acts
as a slave device and the tuner device acts as a master transmitting the
samples. The driver allows asynchronous binding of a tuner device that
is registered as a v4l2 sub-device. The driver can learn about the tuner
it is interfaced with based on port endpoint properties of the device in
device tree. The V4L2 SDR device inherits the controls exposed by the
tuner device.
The device can also be configured to use either one or both of the data
pins at runtime based on the master (tuner) configuration.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch add cec driver for STM32 platforms.
cec hardware block isn't not always used with hdmi so
cec notifier is not implemented. That will be done later
when STM32 DSI driver will be available.
Driver compliance has been tested with cec-ctl and cec-compliance
tools.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
[hans.verkuil@cisco.com: modified platform/Makefile to use obj-y]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
| |
Depending on arch configs to include dirs is evil, and makes
harder to change drivers to work with COMPILE_TEST.
Replace them by obj-y.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
| |
This V4L2 subdev driver enables Digital Camera Memory Interface (DCMI)
of STMicroelectronics STM32 SoC series.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
First version of the Virtual Media Controller.
Add a simple version of the core of the driver, the capture and
sensor nodes in the topology, generating a grey image in a hardcoded
format.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix small typo in Kconfig]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Update the bindings documenting the new hdmi phandle and
update exynos4.dtsi accordingly.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
| |
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
| |
Move this out of the soc_camera directory into the atmel directory
where it belongs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Add v4l2 driver for Mediatek JPEG Decoder
Signed-off-by: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Reviewed-by: Ricky Liang <jcliang@chromium.org>
Tested-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
| |
This V4L2 driver enables DELTA multi-format video decoder
of STMicroelectronics STiH4xx SoC series.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
| |
The FDP1 driver performs advanced de-interlacing on a memory 2 memory
based video stream, and supports conversion from YCbCr/YUV
to RGB pixel formats
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
| |
Add MDP driver for MT8173
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Linking soc_mediabus into this driver causes multiple definition linker warnings
if soc_camera is also enabled:
drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_image_size+0x0): multiple definition of `__ksymtab_soc_mbus_image_size'
drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_image_size+0x0): first defined here
>> drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): multiple definition of `__ksymtab_soc_mbus_samples_per_pixel'
drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): first defined here
drivers/media/platform/soc_camera/built-in.o: In function `soc_mbus_config_compatible':
(.text+0x3840): multiple definition of `soc_mbus_config_compatible'
drivers/media/platform/soc_camera/soc_mediabus.o:(.text+0x134): first defined here
Since we really don't want to have to use any of the soc-camera code this patch
copies the relevant code and data structures from soc_mediabus and renames it to pxa_mbus_*.
The large table of formats has been culled a bit, removing formats that are not supported
by this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
| |
As the conversion to a v4l2 standalone device is finished, move
pxa_camera one directory up and finish severing any dependency to
soc_camera.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds V4L2 HVA (Hardware Video Accelerator) video encoder
driver for STMicroelectronics SoC. It uses the V4L2 mem2mem framework.
This patch only contains the core parts of the driver:
- the V4L2 interface with the userland (hva-v4l2.c)
- the hardware services (hva-hw.c)
- the memory management utilities (hva-mem.c)
This patch doesn't include the support of specific codec (e.g. H.264)
video encoding: this support is part of subsequent patches.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
| |
The s5p-tv driver has been replaced by the exynos drm driver for quite a
long time now. Remove this driver to avoid having duplicate drivers,
of which this one is considered dead code by Samsung.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add driver for the Image Sensor Controller. It manages
incoming data from a parallel based CMOS/CCD sensor.
It has an internal image processor, also integrates a
triple channel direct memory access controller master
interface.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* topic/vsp1: (36 commits)
[media] v4l: vsp1: wpf: Add flipping support
[media] v4l: vsp1: rwpf: Support runtime modification of controls
[media] v4l: vsp1: Simplify alpha propagation
[media] v4l: vsp1: clu: Support runtime modification of controls
[media] v4l: vsp1: lut: Support runtime modification of controls
[media] v4l: vsp1: Support runtime modification of controls
[media] v4l: vsp1: Add Cubic Look Up Table (CLU) support
[media] v4l: vsp1: lut: Expose configuration through a control
[media] v4l: vsp1: lut: Initialize the mutex
[media] v4l: vsp1: dl: Don't free fragments with interrupts disabled
[media] v4l: vsp1: Set entities functions
[media] v4l: vsp1: Don't create LIF entity when the userspace API is enabled
[media] v4l: vsp1: Don't register media device when userspace API is disabled
[media] v4l: vsp1: Base link creation on availability of entities
[media] media: Add video statistics computation functions
[media] media: Add video processing entity functions
[media] v4l: vsp1: sru: Fix intensity control ID
[media] v4l: vsp1: Stop the pipeline upon the first STREAMOFF
[media] v4l: vsp1: Constify operation structures
[media] v4l: vsp1: pipe: Fix typo in comment
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The FCP is a companion module of video processing modules in the
Renesas R-Car Gen3 SoCs. It provides data compression and decompression,
data caching, and conversion of AXI transactions in order to reduce the
memory bandwidth.
The driver is not meant to be used standalone but provides an API to the
video processing modules to control the FCP.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add v4l2 layer encoder driver for MT8173
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
[hans.verkuil@cisco.com: drop unnecessary ARM || ARM64 dependency]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The VPU driver for hw video codec embedded in Mediatek's MT8173 SOCs.
It is able to handle video decoding/encoding of in a range of formats.
The driver provides with VPU firmware download, memory management and
the communication interface between CPU and VPU.
For VPU initialization, it will create virtual memory for CPU access and
IOMMU address for vcodec hw device access. When a decode/encode instance
opens a device node, vpu driver will download vpu firmware to the device.
A decode/encode instant will decode/encode a frame using VPU
interface to interrupt vpu to handle decoding/encoding jobs.
Signed-off-by: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
[hans.verkuil@cisco.com: drop unnecessary ARM || ARM64 dependency]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
| |
A V4L2 driver for Renesas R-Car VIN driver that do not depend on
soc_camera. The driver is heavily based on its predecessor and aims to
replace it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Timberdale FPGA video driver has not seen any real development
since 2011 (and very little before that).
One of the problems with the timblogiw driver is that it uses videobuf
instead of the newer vb2 framework. The long term goal is to either
convert or remove any driver still using videobuf. Since none of the
core v4l developers has the hardware, we cannot convert it ourselves.
As far as I can tell it was only used in an Intel demo board in 2009
using Meego:
http://www.chinait.com/intelcontent/intelprc/admin/PDFFile/20106411545.pdf
which has since been superseded.
Moving this driver to staging is the first step towards removal. After 2 or
3 kernel cycles it will be removed altogether unless someone steps up to
clean up this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Richard Röjfors <richard@puffinpack.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Camera Adaptation Layer (CAL) is a block which consists of a dual
port CSI2/MIPI camera capture engine.
Port #0 can handle CSI2 camera connected to up to 4 data lanes.
Port #1 can handle CSI2 camera connected to up to 2 data lanes.
The driver implements the required API/ioctls to be V4L2 compliant.
Driver supports the following:
- V4L2 API using DMABUF/MMAP buffer access based on videobuf2 api
- Asynchronous sensor sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
|
|
|
|
|
|
|
| |
This patch adds the Kconfig and Makefile for the c8sectpfe driver
so it will be built. It also selects additional demodulator and tuners
which are required by the supported NIM cards.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|